Bulletin I25201 rev. B 03/03 80RIA SERIES PHASE CONTROL THYRISTORS Stud Version Features Hermetic glass-metal seal International standard case TO-209AC (TO-94) 80A Typical Applications DC motor controls Controlled DC power supplies AC controllers Major Ratings and Characteristics Parameters 80RIA Unit 80 A 85 °C 125 A @ 50Hz 1900 A @ 60Hz 1990 A @ 50Hz 18 KA2s @ 60Hz 16 KA2s 400 to 1200 V 110 µs - 40 to 125 °C IT(AV) @ TC IT(RMS) ITSM I 2t V DRM /V RRM tq typical TJ www.irf.com case style TO-209AC (TO-94) 1 80RIA Series Bulletin I25201 rev. B 03/03 ELECTRICAL SPECIFICATIONS Voltage Ratings Type number Voltage V DRM/V RRM, max. repetitive VRSM , maximum non- I DRM/I RRM max. Code peak and off-state voltage repetitive peak voltage @ TJ = 125°C V V mA 40 400 500 80 800 900 120 1200 1300 80RIA 15 On-state Conduction Parameter I T(AV) 80RIA Units Conditions Max. average on-state current 80 A @ Case temperature 85 °C I T(RMS) Max. RMS on-state current 125 A I TSM Max. peak, one-cycle 1900 t = 10ms non-repetitive surge current 1990 t = 8.3ms reapplied 1600 t = 10ms 100% VRRM 1675 t = 8.3ms reapplied Sinusoidal half wave, 18 t = 10ms No voltage Initial TJ = TJ max. I2t Maximum I2t for fusing 16 I 2√t Maximum I2√t for fusing V T(TO)1 Low level value of threshold voltage V T(TO) 2 High level value of threshold voltage r t1 Low level value of on-state High level value of on-state slope resistance No voltage t = 8.3ms reapplied t = 10ms 100% VRRM 11.7 t = 8.3ms reapplied 180.5 KA2 s KA2√s t = 0.1 to 10ms, no voltage reapplied (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. 0.99 V (I > π x IT(AV)),TJ = TJ max. 1.13 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. 2.29 mΩ (I > π x IT(AV)),TJ = TJ max. 1.84 V TM Max. on-state voltage 1.60 IH Maximum holding current 200 IL Typical latching current 400 2 DC @ 75°C case temperature 12.7 slope resistance r t2 A 180° conduction, half sine wave V mA Ipk= 250A, TJ = 25°C tp = 10ms sine pulse T J = 25°C, anode supply 12V resistive load www.irf.com 80RIA Series Bulletin I25201 rev. B 03/03 Switching Parameter di/dt 80RIA Units Max. non-repetitive rate of rise of turned-on current Conditions TJ = 125°C, Vd = rated VDRM, ITM = 2xdi/dt snubber 300 A/µs 0.2µF, 15Ω, Gate pulse: 20V, 65Ω, tp = 6µs, tr= 0.5µs Per JEDEC Standard RS-397, 5.2.2.6. td tq Typical delay time Gate pulse: 10V, 15Ω source, tp = 6µs, tr = 0.1µs, 1 µs Typical turn-off time Vd = rated VDRM, ITM = 50Adc, TJ = 25°C. ITM = 50A, TJ = TJ max, di/dt = -5A/µs min., VR = 50V, 110 dv/dt = 20V/µs, Gate bias: 0V 25Ω, tp = 500µs Blocking Parameter 80RIA Units Conditions dv/dt Maximum critical rate of rise of off-state voltage 500 V/µs TJ = 125°C exponential to 67% rated VDRM IRRM IDRM Max. peak reverse and off-state leakage current 15 mA TJ = 125°C rated V DRM /V RRM applied 80RIA Units Triggering Parameter PGM Maximum peak gate power 3 IGM Max. peak positive gate current 3 +VGM Maximum peak positive gate voltage -VGM Maximum peak negative W TJ = TJ max, t p ≤ 5ms TJ = TJ max, f = 50Hz, d% = 50 A TJ = TJ max, t p ≤ 5ms 12 PG(AV) Maximum average gate power Conditions 20 V TJ = TJ max, tp ≤ 5ms 10 gate voltage IGT VGT Max. DC gate current required 270 to trigger 120 TJ = - 40°C mA TJ = 25°C 60 TJ = 125°C Max. DC gate voltage required 3.5 TJ = - 40°C to trigger 2.5 V 1.5 TJ = 25°C TJ = 125°C IGD DC gate current not to trigger 6 mA VGD DC gate voltage not to trigger 0.25 V TJ = TJ max www.irf.com Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 6V anode-to-cathode applied Max. gate current/ voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied 3 80RIA Series Bulletin I25201 rev. B 03/03 Thermal and Mechanical Specification Parameter 80RIA Units TJ Max. operating temperature range -40 to 125 Tstg Max. storage temperature range -40 to 150 RthJC Max. thermal resistance, 0.1 case to heatsink Mounting torque, ± 10% wt DC operation K/W RthCS Max. thermal resistance, T °C 0.30 junction to case Conditions Mounting surface, smooth, flat and greased 15.5 (137) Approximate weight Case style 14 (120) Nm (lbf-in) 130 g TO-209AC(TO-94) Non lubricated threads Lubricated threads See Outline Table ∆RthJ-C Conduction (The following table shows the increment of thermal resistence RthJ-C when devices operate at different conduction angles than DC) Conduction angle Sinusoidal conduction Rectangular conduction Units 180° 0.042 0.030 120° 0.050 0.052 90° 0.064 0.070 60° 0.095 0.100 30° 0.164 0.165 K/W Conditions T J = T J max. Ordering Information Table Device Code 1 - 2 - 8 0 1 2 RIA 120 3 4 ITAV x 10A 0 = Eyelet terminals (Gate and Auxiliary Cathode Leads) 1 = Fast - on terminals (Gate and Auxiliary Cathode Leads) 3 - RIA = Essential part number 4 - Voltage code: Code x 10 = VRRM (See Voltage Rating Table) 5 - None = Stud base 1/2"-20UNF- 2A threads NOTE: For Metric Device M12 x 1.75 E6 Contact factory 4 www.irf.com 80RIA Series Bulletin I25201 rev. B 03/03 Outline Table GLASS METAL SEAL 16.5 (0.65) MAX. 37 )M IN. 2.5 (0.10) MAX. IN. 79 9 .5 ( 0. 4.3 (0.17) DIA. )M 8.5 (0.3) DIA. (0 . FLEXIBLE LEAD 20 C.S. 16mm 2 (.025 s.i.) 170 (6.69) C.S. 0.4 mm (.0006 s.i.) 2 Fast-on Terminals AMP. 280000-1 REF-250 RED CATHODE WHITE GATE 215 (8.46) 55 (2.17) MIN. 10 (0.39) RED SHRINK 23.5 (0.92) MAX. DIA. MAX. 10 (0.39) MAX. 24 (0.94) MAX. WHITE SHRINK 21 (0.83) 157 (6.18) RED SILICON RUBBER SW 27 1/2"-20UNF-2A * Case Style TO-209AC (TO-94) All dimensions in millimeters (inches) 29.5 (1.16) MAX. 130 80RIA Series RthJC (DC) = 0.30 K/ W 120 110 Conduc tion Angle 100 30° 60° 90° 120° 90 180° 80 0 10 20 30 40 50 60 70 80 90 Maximum Allowable Case Temperature (°C) Maximum Allowable Case Temperature (°C) * FOR METRIC DEVICE: M12 X 1.75 E6 CONTACT FACTORY 130 80RIA Series RthJC (DC) = 0.30 K/ W 120 110 Conduction Period 100 90 30° 80 60° 90° 120° 180° DC 70 0 20 40 60 80 100 120 Average On-state Current (A) Average On-state Current (A) Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics www.irf.com 140 5 80RIA Series 120 W K/ 0.4 1 = K/ W -D elt 80 A 90 W K/ 100 hS R t 180° 120° 90° 60° 30° 110 6 0. 1.4 K/ W RMSLimit 60 R 70 a Maximum Average On-state Power Loss (W) Bulletin I25201 rev. B 03/03 2K /W 50 40 Conduction Angle 3 K/ 30 80RIA Series TJ = 125°C 20 10 W 5 K/ W 0 0 10 20 30 40 50 60 70 80 0 Average On-state Current (A) 25 50 75 100 125 Maximum Allowable Ambient Temperature (°C) Maximum Average On-state Power Loss (W) Fig. 3 - On-state Power Loss Characteristics 180 DC 180° 120° 90° 60° 30° 160 140 120 R th SA 0. 6 = 0. 4 K/ W 100 80 K/ W -D el ta 1K /W RMSLimit Conduc tion Period 60 R 1.4 K/ W 2 K/ W 3 K/ W 40 80RIA Series TJ = 125°C 20 5 K/ W 0 0 20 40 60 80 100 120 Average On-state Current (A) 140 0 25 50 75 100 125 Maximum Allowable Ambient Temperature (°C) 1800 At Any Rated Load Condition And With Rated VRRM Applied Following Surge. Initial TJ = 125°C @60 Hz 0.0083 s @50 Hz 0.0100 s 1600 1400 1200 1000 80RIA Series 800 1 10 100 Number Of Equa l Amplitude Half Cycle Current Pulses (N) Fig. 5 - Maximum Non-Repetitive Surge Current 6 Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) Fig. 4 - On-state Power Loss Characteristics 2000 Maximum Non Repetitive Surge Current 1900 Versus Pulse Train Duration. Control 1800 Of Conduction May Not Be Maintained. Initial TJ = 125°C 1700 No Voltage Reapplied 1600 Rated VRRM Reapplied 1500 1400 1300 1200 1100 1000 900 80RIA Series 800 700 0.01 0.1 1 Pulse Train Duration (s) Fig. 6 - Maximum Non-Repetitive Surge Current www.irf.com 80RIA Series Bulletin I25201 rev. B 03/03 Instantaneous On-state Current (A) 10000 1000 100 TJ = 25°C TJ = 125°C 10 80RIA Series 1 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 Instantaneous On-state Voltage (V) Fig. 7 - On-state Voltage Drop Characteristics (K/ W) 1 Steady State Value Transient Thermal Impedance Z thJC R thJC = 0.30 K/ W (DC Operation) 0.1 0.01 80RIA Series 0.001 0.0001 0.001 0.01 0.1 1 10 Sq uare Wave Pulse Duration (s) Fig. 8 - Thermal Impedance ZthJC Characteristics Rectangular gate pulse a) Recommended load line for rated di/ dt : 20V, 30ohms; tr<=0.5 µs b) Recommended load line for <=30% rated di/ dt : 20V, 65ohms 10 tr<=1 µs IGD 0.01 (1) (2) (a) (3) (4) (b) VGD 0.1 0.001 (1) PGM = 100W, tp = 500µs (2) PGM = 50W, tp = 1ms (3) PGM = 20W, tp = 2.5ms (4) PGM = 10W, tp = 5ms Tj=-40 °C 1 Tj=25 °C Tj=125 °C Instantaneous Gate Voltage (V) 100 Device: 80RIA Series 0.1 Frequency Limited by PG(AV) 1 10 100 1000 Instantaneous Gate Current (A) Fig. 9 - Gate Characteristics www.irf.com 7 80RIA Series Bulletin I25201 rev. B 03/03 Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 03 /03 8 www.irf.com