Data Sheet No. PD94122 IRU1015 1.5A LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR DESCRIPTION FEATURES Guaranteed < 1.3V Dropout at Full Load Current Fast Transient Response 1% Voltage Reference Initial Accuracy Output Current Limiting Built-In Thermal Shutdown The IRU1015 is a low dropout three-terminal adjustable regulator with minimum of 1.5A output current capability. This product is specifically designed to provide well regulated supply for low voltage IC applications such as 486DX4 processor, P55C I/O supply as well as high speed bus termination and low current 3.3V logic supply. The IRU1015 is also well suited for other applications such as VGA and sound card. The IRU1015 is guaranteed to have <1.3V dropout at full load current making it ideal to provide well regulated outputs of 2.5V to 3.3V with 4.75V to 7V input supply. APPLICATIONS 486DX4 Supply Voltage P55 I/O Supply Voltage VGA & Sound Card Applications Low Voltage High Speed Termination Applications Standard 3.3V Chip Set and Logic Applications TYPICAL APPLICATION 5V IRU1015 C1 1500uF Vin 3 Vout 2 3.3V / 1.5A R1 121 Adj R2 200 1 C2 1500uF 1015app1-1.1 Figure 1 - Typical application of IRU1015 in a 5V to 3.3V regulator Note: P55C is trademark of Intel Corp. PACKAGE ORDER INFORMATION Tj (°C) 0 To 150 Rev. 1.1 06/29/01 3-PIN PLASTIC TO-220 (T) IRU1015CT 3-PIN PLASTIC TO-263 (M) IRU1015CM 2-PIN PLASTIC TO-252 (D-Pak) IRU1015CD 1 IRU1015 ABSOLUTE MAXIMUM RATINGS Input Voltage (Vin) .................................................... Power Dissipation ..................................................... Storage Temperature Range ...................................... Operating Junction Temperature Range ..................... 7V Internally Limited -65°C To 150°C 0°C To 150°C PACKAGE INFORMATION 3-PIN PLASTIC TO-220 (T) 3-PIN PLASTIC TO-263 (M) FRONT VIEW FRONT VIEW 3 Tab is Vout 2-PIN PLASTIC TO-252 (D-Pak) Vin 2 Vout 1 Adj θJT=2.7°C/W θJA=60°C/W FRONT VIEW 3 Tab is Vout Vin Adj θJA=35°C/W for 1" Square pad Vin 1 Adj Tab is Vout Vout 1 3 θJA=70°C/W for 0.5" Square pad ELECTRICAL SPECIFICATIONS Unless otherwise specified, these specifications apply over Cin=1µF, Cout=10µF, and Tj=0 to 150!C. Typical values refer to Tj=25!C. PARAMETER Reference Voltage Line Regulation Load Regulation (Note 1) Dropout Voltage (Note 2) Current Limit Minimum Load Current (Note 3) Thermal Regulation Ripple Rejection Adjust Pin Current Adjust Pin Current Change Temperature Stability Long Term Stability RMS Output Noise SYM Vref ∆Vo Iadj TEST CONDITION MIN TYP Io=10mA, Tj=25!C, (Vin-Vo)=1.5V 1.238 1.250 Io=10mA, (Vin-Vo)=1.5V 1.225 1.250 Io=10mA, 1.3V<(Vin-Vo)<7V Vin=3.3V, Vadj=0, 10mA<Io<1.5A Note 2, Io=1.5A 1.1 Vin=3.3V, dVo=100mV 1.6 Vin=3.3V, Vadj=0V 5 MAX 1.262 1.275 0.2 0.4 1.3 10 % % V A mA 30ms Pulse, Vin-Vo=3V, Io=1.5A f=120Hz, Co=25µF Tantalum, Io=0.75A, Vin-Vo=3V Io=10mA, Vin-Vo=1.5V, Tj=25!C, Io=10mA, Vin-Vo=1.5V Io=10mA, Vin-Vo=1.5V, Tj=25!C Vin=3.3V, Vadj=0V, Io=10mA Tj=125!C, 1000Hrs Tj=25!C, 10Hz<f<10KHz 0.02 %/W Note 1: Low duty cycle pulse testing with Kelvin connections is required in order to maintain accurate data. Note 2: Dropout voltage is defined as the minimum differential voltage between Vin and Vout required to maintain regulation at Vout. It is measured when the output voltage drops 1% below its nominal value. 2 0.01 60 70 55 0.2 0.5 0.3 0.003 UNITS V dB 120 5 1 µA µA % % %Vo Note 3: Minimum load current is defined as the minimum current required at the output in order for the output voltage to maintain regulation. Typically the resistor dividers are selected such that it automatically maintains this current. Rev. 1.1 06/29/01 IRU1015 PIN DESCRIPTIONS PIN # PIN SYMBOL PIN DESCRIPTION 1 Adj A resistor divider from this pin to the Vout pin and ground sets the output voltage. 2 Vout The output of the regulator. A minimum of 10µF capacitor must be connected from this pin to ground to insure stability. 3 Vin The input pin of the regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum drop out voltage during the load transient response. This pin must always be 1.3V higher than Vout in order for the device to regulate properly. BLOCK DIAGRAM Vin 3 2 Vout + 1.25V + CURRENT LIMIT THERMAL SHUTDOWN 1015blk1-1.0 1 Adj Figure 2 - Simplified block diagram of the IRU1015 APPLICATION INFORMATION Introduction The IRU1015 adjustable Low Dropout (LDO) regulator is a three-terminal device which can easily be programmed with the addition of two external resistors to any voltages within the range of 1.25 to 5.5 V.This regulator unlike the first generation of the three-terminal regulators such as LM117 that required 3V differential between the input and the regulated output, only needs 1.3V differential to maintain output regulation. This is a key requirement for today’s microprocessors that need typically 3.3V supply and are often generated from the 5V supply. Another major requirement of these microproces- Rev. 1.1 06/29/01 sors is the need to switch the load current from zero to full load in tens of nanoseconds at their pins, which translates to an approximately 300 to 500ns current step at the regulator. In addition, the output voltage tolerances are sometimes tight and they include the transient response as part of the specification. The IRU1015 is specifically designed to meet the fast current transient needs as well as provide an accurate initial voltage, reducing the overall system cost with the need for fewer output capacitors. 3 IRU1015 Output Voltage Setting The IRU1015 can be programmed to any voltages in the range of 1.25V to 5.5V with the addition of R1 and R2 external resistors according to the following formula: VOUT = VREF × o1 + R2 p + IADJ × R2 R1 Where: VREF = 1.25V Typically IADJ = 50µA Typically R1 and R2 as shown in figure 3: regulator and not to the load. In fact, if R1 is connected to the load side, the effective resistance between the regulator and the load is gained up by the factor of (1+R2/ R1), or the effective resistance will be, Rp(eff)=Rp*(1+R2/ R1). It is important to note that for high current applications, this can represent a significant percentage of the overall load regulation and one must keep the path from the regulator to the load as short as possible to minimize this effect. PARASITIC LINE RESISTANCE Rp Vin Vin Vout Vout Vin Vout IRU1015 IRU1015 Adj Vin Vref IAdj = 50uA Adj R1 RL R1 R2 R2 1015app2-1.0 1015app3-1.0 Figure 3 - Typical application of the IRU1015 for programming the output voltage. The IRU1015 keeps a constant 1.25V between the output pin and the adjust pin. By placing a resistor R1 across these two pins a constant current flows through R1, adding to the Iadj current and into the R2 resistor producing a voltage equal to the (1.25/R1)*R2 + Iadj*R2 which will be added to the 1.25V to set the output voltage. This is summarized in the above equation. Since the minimum load current requirement of the IRU1015 is 10mA, R1 is typically selected to be 121Ω resistor so that it automatically satisfies the minimum current requirement. Notice that since Iadj is typically in the range of 50µA it only adds a small error to the output voltage and should only be considered when a very precise output voltage setting is required. For example, in a typical 3.3V application where R1=121Ω and R2=200Ω the error due to Iadj is only 0.3% of the nominal set point. Load Regulation Since the IRU1015 is only a three-terminal device, it is not possible to provide true remote sensing of the output voltage at the load. Figure 4 shows that the best load regulation is achieved when the bottom side of R2 is connected to the load and the top side of R1 resistor is connected directly to the case or the Vout pin of the 4 Figure 4 - Schematic showing connection for best load regulation Stability The IRU1015 requires the use of an output capacitor as part of the frequency compensation in order to make the regulator stable. Typical designs for microprocessor applications use standard electrolytic capacitors with a typical ESR in the range of 50 to 100mΩ and an output capacitance of 500 to 1000µF. Fortunately as the capacitance increases, the ESR decreases resulting in a fixed RC time constant. The IRU1015 takes advantage of this phenomena in making the overall regulator loop stable. For most applications a minimum of 100µF aluminum electrolytic capacitor such as Sanyo MVGX series, Panasonic FA series as well as the Nichicon PL series insures both stability and good transient response. Thermal Design The IRU1015 incorporates an internal thermal shutdown that protects the device when the junction temperature exceeds the maximum allowable junction temperature. Although this device can operate with junction temperatures in the range of 150!C, it is recommended that the selected heat sink be chosen such that during maximum continuous load operation the junction temperature is kept below this number. The example below Rev. 1.1 06/29/01 IRU1015 shows the steps in selecting the proper regulator heat sink for an AMD 486DX4-120 MHz processor. Assuming the following specifications: VIN = 5V VOUT = 3.45V IOUT(MAX) = 1.2A TA = 35!C The steps for selecting a proper heat sink to keep the junction temperature below 135°C is given as: 1) Calculate the maximum power dissipation using: PD = IOUT × (VIN - VOUT) PD = 1.2 × (5 - 3.45) = 1.86W 2) Select a package from the regulator data sheet and record its junction to case (or Tab) thermal resistance. Selecting TO-220 package gives us: θJC = 2.7!C/W 3) Assuming that the heat sink is black anodized, calculate the maximum Heat sink temperature allowed: Assume, θcs=0.05°C/W (heat-sink-to-case thermal resistance for black anodized) TS = TJ - PD × (θJC + θCS) TS = 135 - 1.86 × (2.7 + 0.05) = 129!C 4) With the maximum heat sink temperature calculated in the previous step, the heat-sink-to-air thermal resistance (θSA) is calculated by first calculating the temperature rise above the ambient as follows: ∆T = TS - TA = 129 - 35 = 94!C ∆T = Temperature Rise Above Ambient θSA = ∆T 94 = = 50!C/W PD 1.86 Thermalloy AAVID 0 6041PB 574602 Air Flow (LFM) 100 No HS Required No HS Required Note: For further information regarding the above companies and their latest product offerings and application support contact your local representative or the numbers listed below: AAVID...............PH# (603) 528 3400 Thermalloy.........PH# (214) 243-4321 Designing for Microprocessor Applications As it was mentioned before the IRU1015 is designed specifically to provide power for the new generation of the low voltage processors requiring voltages in the range of 2.5V to 3.6V generated by stepping down the 5V supply. These processors demand a fast regulator that supports their large load current changes. The worst case current step seen by the regulator is anywhere in the range of 1 to 7A with the slew rate of 300 to 500ns which could happen when the processor transitions from “Stop Clock” mode to the “Full Active” mode. The load current step at the processor is actually much faster, in the order of 15 to 20ns, however, the de-coupling capacitors placed in the cavity of the processor socket handle this transition until the regulator responds to the load current levels. Because of this requirement the selection of high frequency low ESR and low ESL output capacitor is imperative in the design of these regulator circuits. Figure 5 shows the effects of a fast transient on the output voltage of the regulator. As shown in this figure, the ESR of the output capacitor produces an instantaneous drop equal to the (∆VESR=ESR*∆I) and the ESL effect will be equal to the rate of change of the output current times the inductance of the capacitor (∆VESL =L*∆I/∆t). The output capacitance effect is a droop in the output voltage proportional to the time it takes for the regulator to respond to the change in the current, (∆VC = ∆t * ∆I / C ) where ∆t is the response time of the regulator. 5) Next, a heat sink with lower θsa than the one calculated in step 4 must be selected. One way to do this is to simply look at the graphs of the "Heat Sink Temp Rise Above the Ambient" vs. the "Power Dissipation" and select a heat sink that results in lower temperature rise than the one calculated in the previous step. The following heat sinks from AAVID and Thermalloy meet this criteria. Rev. 1.1 06/29/01 5 IRU1015 2) With the output capacitance being 1500µF: V ESR V ESL VC T LOAD CURRENT ∆t × ∆I 2 × 1.2 = = 1.6mV C 1500 Where: ∆t = 2µs is the regulator response time 1015plt1-1.0 To set the output voltage, we need to select R1 and R2: LOAD CURRENT RISE TIME Figure 5 - Typical regulator response to the fast load current step An example of a regulator design to meet the AMD specification for 486DX4-120MHz is given below. Assume the specification for the processor as shown in Table 1: Type of Processor AMD 486DX4 ∆Vc = Vout Nominal 3.45 V Imax 1.2 A Max Allowed Output Tolerance ±150 mV 3) Assuming R1 = 121Ω, 1% VOUT 3.45 o p× 121 =o o p× 121 = 213Ω - 1p - 1p R2 =o VREF 1.25 Select R2 = 215Ω, 1% Selecting both R1 and R2 resistors to be 1% tolerance results in the least amount of error introduced by the resistor dividers leaving a ≈ ±2.5% error budget for the IRU1015 reference which is well within the initial accuracy of the device. Finally, the input capacitor is selected as follows: Table 1 - GTL+ specification for Pentium Pro The first step is to select the voltage step allowed in the output due to the output capacitor’s ESR: 1) Assuming the regulator’s initial accuracy plus the resistor divider tolerance is ≈ ±86mV (±2.5% of 3.45V nominal), then the total step allowed for the ESR and the ESL, is -64mV. Assuming that the ESL drop is -10mV, the remaining ESR step will be -54mV. Therefore the output capacitor ESR must be: ESR ≤ 54 = 45mΩ 1.2 The Sanyo MVGX series is a good choice to achieve both price and performance goals. The 6MV1500GX, 1500µF, 6.3V has an ESR of less than 36mΩ typical. Selecting a single capacitor achieves our design goal. The next step is to calculate the drop due to the capacitance discharge and make sure that this drop in voltage is less than the selected ESL drop in the previous step. 6 4) Assuming that the input voltage can drop 150mV before the main power supply responds, and that the main power supply response time is ≈ 50ms, then the minimum input capacitance for a 1.2A load step is given by: CIN = 1.2 × 50 = 400µF 0.15 The ESR should be less than: ESR = (VIN - VOUT - ∆V - VDROP) ∆I Where: VDROP L Input voltage drop allowed in step 4 ∆V L Maximum regulator dropout voltage ∆I L Load current step ESR = (5 - 3.45 - 1.2 - 0.15) = 0.167Ω 1.2 Select a single 1500µF the same type as the output capacitors exceeds our requirements.Figure 6 shows the completed schematic for our example. Rev. 1.1 06/29/01 IRU1015 5V C1 1500uF Vin 3.45V Vout C2 1500uF IRU1015 Adj R1 121 1% R2 215 1% Layout Consideration The output capacitors must be located as close to the Vout terminal of the device as possible. It is recommended to use a section of a layer of the PC board as a plane to connect the Vout pin to the output capacitors to prevent any high frequency oscillation that may result from excessive trace inductance. 1015app4-1.1 Figure 6 - Final schematic for the regulator design Rev. 1.1 06/29/01 7 IRU1015 Notes IR WORLD HEADQUARTERS : 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. Data and specifications subject to change without notice. 02/01 8 Rev. 1.1 06/29/01