FieldPower® MPB Product Information Decentralised Automation Building automation Building automation FieldPower® MPB – Belimo system partner FieldPower® for the Multi-point bus – strategic cabling In cooperation with BELIMO, the world's leading manufacturer of heating, cooling and climate control systems, the FieldPower® installation base has been extended to include the MP bus. The Multi-point bus is a simple actuating and sensing bus. It requires neither a special bus line nor a shielded cable. It can be implemented using the standard TT or NYM installation cables. However, when using conventional wiring methods, it is not possible to carry out the installation in a quick and precise manner. This prevents it from being completely accepted as a system solution. Research shows that more than half of all installation errors occur because of erroneous connections. These occur even Quick installation with no errors •The installation cable is first partially stripped using Weidmüller AM16 tool and the individual wires are connected reliably and securely with IDC contacts (the patented insulation displacement contact with external spring). •The wires cannot be mixed up since they are never cut all the way through. Other contact problems, such as insulation that is pushed under, are also no longer possible. •The wire colours along with the labelling are within the contact module. So here too there is no way for a mix-up to occur. •The end position of the contact discs is clear and can even be seen from a distance of three metres. when using a clear connection diagram under clean working conditions. But it is not the electricians who are at fault. They must be familiar with a variety of different communication systems while struggling with tighter deadlines and the shortage of qualified personnel. Now FieldPower® allows them to achieve both goals: No wiring errors all the way from the controller in the electrical cabinet to the end device – using standard installation cable. For further information, please visit www.weidmueller.com/int/belimo Stern Fieldbus system (optional) Linien A comprehensive feature set •The FieldPower® Terminal for solid-core wires from 1.5 to 6 mm² with standard Baum Netzwerk TT or NYM mit installation Maschen lines in one variant. •The 5-pole version allows for longer line lengths with its doubled earth. •IP20 or IP42/65 protection to fit the installed location. •The PUSH IN contacts can be used to create a flexible bus topology. •A pluggable electronics module (under Belimo order code “ZFP-MP”) is used to connect the sensors and actuators with the MP bus and with the sensors' shield connection. •The service interface is used for initial commissioning. This process is significantly simplified since the closed cover is detected automatically. •The RJ interface can be used to access the entire bus from any FieldPower® MPB module. •All MP devices can be isolated from the bus without having the master separated in the electrical cabinet. Belimo Automation AG is a publicly held technology company with over 1100 employees worldwide. Since 1975, Belimo has been designing, manufacturing and selling electrical drives for ventilation flaps and fixtures in heating, ventilation and climate control systems. Belimo has a comprehensive product line and is the global market leader in this specific market. Belimo has chosen the FieldPower® system as the standard solution for the control and supply of sensors and actuators using MP bus distribution. Some feedback from the field: The electrician: "I've finally found a simple way to verify and log my work using the PC software. And there's enough space in the box for carrying out a proper installation." The system integrator: "The cabling system means that I only have to connect the controller. The PC software log from the electrician confirms that the installation was proper and that all MP devices are ready for operation." The building developer: "Thanks to this system the construction takes only half the time. The MP devices can be diagnosed quickly and there's no need to open up the electrical cabinet! All facilities now have a consistent setup." 2 3 FieldPower® MPB FieldPower® Terminal MPB FieldPower® Box MPB With bright-grey hood Contact unit for error-free Multi-point bus distribution from the electrical cabinet to the end device, with conventional installation cables. Grau Grey Gelb Yellow Braun Brown Schwarz Black Schwarz Black 67 60 74,9 157 104 181 Technical data Rated data according to IEC 60947-7-1 Rated cross-section Rated voltage/Rated current Rated impulse voltage General data Insulation material/material colour UL 94 flammability class free from halogens/Silicone-free Protection degree Assembly temperature range, min.-max. Operating temperature, min.-max. Can be coded IDC connection clamping capacity - power cable solid, min.-max. stranded, min.-max. flexible, min.-max. flexible, min.-max. Blade size PUSH IN connection clamping capacity - distribution solid, min.-max. stranded, min.-max. flexible, min.-max. flexible, wire end ferrule 8 mm, DIN 46228/1, min-max. flexible, wire end ferrule 8 mm, DIN 46228/4, min-max. flexible, wire end ferrule 12 mm, DIN 46228/1, min-max. flexible, wire end ferrule 12 mm, DIN 46228/4, min-max. flexible, min.-max. Stripping length/Blade size 6 mm2 800 V/41 A 8 kV 6 mm2 800 V/41 A 8 kV Polycarbonate/grey V0 Yes/Yes IP 20 10 °C...40 °C -40 °C...55 °C Yes Polycarbonate/black 5VA Yes/Yes IP 65 10 °C...40 °C -40 °C...55 °C Yes 1.5 mm2…6 mm2 2.5 mm2…6 mm2 2.5 mm2…6 mm2 2.5 mm2…6 mm2 0.6 x 3.5 mm 1.5 mm2…6 mm2 2.5 mm2…6 mm2 2.5 mm2…6 mm2 2.5 mm2…6 mm2 0.6 x 3.5 mm 0.5 mm2…6 mm2 0.5 mm2…6 mm2 0.5 mm2…10 mm2 0.5 mm2…6 mm2 0.5 mm2…4 mm2 0.5 mm2…6 mm2 0.5 mm2…4 mm2 0.5 mm2…6 mm2 14 mm/0.6 x 3.5 mm 0.5 mm2…6 mm2 0.5 mm2…6 mm2 0.5 mm2…10 mm2 0.5 mm2…6 mm2 0.5 mm2…4 mm2 0.5 mm2…6 mm2 0.5 mm2…4 mm2 0.5 mm2…6 mm2 14 mm/0.6 x 3.5 mm Note Ordering data Type FP Terminal LG MPB Note Qty. 1 Order No. 1206530000 Type FP Box MPB Enclosure seals can be ordered separately. Accessories Note 4 Plug-in connector PTS 4 MPB 1010910000 (Qty. = 10) Plug-in connector PTS 4 MPB 1010910000 (Qty. = 10) Qty. 1 Order No. 1180300000 FieldPower® MPB PTS 4 MPB Contact unit for error-free Multi-point bus distribution from the electrical cabinet to the end device, with conventional installation cables. Codable and latchable with a plug connector at the beginning instead of a contact header. 55,45 Accessories from Belimo 36,15 22 27,3 Technical data Rated data according to IEC 60947-7-1 Rated cross-section Rated voltage/Rated current Rated impulse voltage General data Type of mounting Insulation material/material colour UL 94 flammability class Continuous operating temp., min.-max. Outgoing direction of conductor Test point Can be coded Conductor connection system No. of poles Number of connections / pole Clamping capacity, PUSH IN connection Clamping range, min.-max. solid, min.-max. stranded, min.-max. flexible, min.-max. flexible, wire end ferrule 8 mm, DIN 46228/1, min.-max. flexible, wire end ferrule 8 mm, DIN 46228/4, min.-max. flexible, wire end ferrule 12 mm, DIN 46228/1, min.-max. flexible, wire end ferrule 12 mm, DIN 46228/4, min.-max. flexible, min.-max. Stripping length/Blade size The connection element "ZFP-MP" (see figure) can be otained from BELIMO. 4 mm² 690 V / 32 A 8 kV Features: • Can optionally connect two MP devices or one MP device and one sensor • Service socket for Belimo tools • MP drives connected with plug-in connector Plugged PA GF/ black V0 -50 °C...120 °C 90° 2 mm YES / Not coded PUSH IN 5 1 Suitable for Weidmüller: FP Terminal LG MPB BELIMO: EXT-WR-FP20-MP (IP20) and 0.5 mm²…4 mm² 0.5 mm²…4 mm² 0.5 mm²…4 mm² 0.5 mm²…4 mm² 0.5 mm²…4 mm² 0.5 mm²…4 mm² 0.5 mm²…4 mm² 0.5 mm²…4 mm² 0.5 mm²…4 mm² 12 mm / 3.0 x 0.5 mm Weidmüller: FP Box MPB BELIMO: EXT-WR-FP65-MP (IP65) Note Ordering data Type PTS 4 MPB Qty. 10 Note Accessories Note 5 ZVR ZP2.5 locking element 1816130000 Order No. 1010910000 Accessories Seals for FieldPower® Box Seal for round cable Blanking seal IP65 enclosure seals for the FieldPower Box modules: made from silicone-free, halogen-free material. The seals are slit in the middle to allow for simple installation with uncut power cables. ® ø Technical data General data Material UL 94 flammability class Colour Thickness Line type Free from halogens Silicone-free Ingress protection class EPDM HB black 18 mm round Yes Yes IP 65 EPDM HB black 18 mm Yes Yes IP 65 Note Ordering data Clamping range Ø 7.5 - 9 mm 9 - 11 mm 11 - 13 mm 13 - 15 mm 15 - 17 mm Note Accessories Note 6 Type RKDG D9 PT6 RKDG D11 PT6 RKDG D13 PT6 RKDG D15 PT6 RKDG D17 PT6 Qty. 10 10 10 10 10 Order No. 4329610000 4323210000 4323230000 4323220000 4324010000 Type DG D0 PT6 Qty. 10 Order No. 4323240000 Tools Sheathing stripper • Sheathing stripper for PVC cables Technical data Max. stripping performance Cable model Conductor cross-section Conductor diameter Max. stripping length Adjustable depth of cut Cutting performance Max. cutting performance mm2 mm mm mm AM 16 AM 25 • Sheathing stripper for round PVC cables • Insulation can be stripped from any point along the cable • Especially suitable for stripping cables in the cable duct, too. • Hinged knife for circumferential and longitudial cuts • Handle tips with integrated cutter for opening slit insulation • Pivoting blade for circumferential, lengthwise and spiral cuts • Retaining clip with integrated blade to break open an incision in the insulation • Integrated spare blade AM 16 PVC round cable AM 25 PVC round cable 6…17.3 6…25 0.8 - 2.5 mm up to 4.5 mm 53 60 135 135 mm2 Tool data Lengthmm Weightg Note Ordering data Version Type AM 16 Qty. 1 Order No. 9204190000 Type AM 25 Qty. 1 Order No. 9001540000 Type Spare blade Qty. 1 Order No. 9204260000 Type Spare blade Qty. 2 Order No. 9001530000 Note Accessories Note 7 Sheathing stripper Sheathing stripper Tools KT 20 SD S / SDK PZ2 Cutter Screwdriver Cutting tool that does not damage the conductor; for cutting copper and aluminium cables with a diameter of up to 20 mm. • Not suitable for steel wires, steel-armoured cables, aluminium alloys and hard-drawn copper conductors! • Easy handling because of automatic opening • Safety lock reduces risk of injury Technical data Max. cutting performance copper cable Solid (max. conductor cross-section) mm2 / AWG Stranded (max. conductor cross-section) mm2 / AWG Flexible (max. conductor cross-section) mm2 / AWG Flexible, Stranded (max. diameter) mm Sector line Max. cutting performance aluminium cable stranded (conductor cross-section max.) mm2 / AWG Stranded (max. diameter) mm solidmm2 Data-/ telephone-/ control cable O.D. max. mm Tool data Length / width / height mm Weightg KT20 16 / 6 35 / 2 70 / 2/0 20 Note Tool closed Ordering data 20 215 / 66 / 29 400 Version Type KT 20 Note Specifying solid-core aluminium cable corresponds to sector-shaped conductor with individual strands Accessories Note 8 70 / 2/0 20 35 Type Qty. 1 Qty. Order No. 9002300000 Order No. Type SDK PZ2 SD 0,5 x 3,0 x 80 SD 0,6 x 3,5 x 100 Qty. 1 1 1 Order No. 9008540000 9008320000 9008330000 Type Qty. Order No. Drilling templates Drilling templates 29.9 69.2 PT6 108.5 139.5 89 89 104 FieldPower® Box 165 181 9 Weidmüller – Your partner in Industrial Connectivity As experienced experts we support our customers and partners around the world with products, solutions and services in the industrial environment of power, signal and data. We are at home in their industries and markets and know the technological challenges of tomorrow. We are therefore continuously developing innovative, sustainable and useful solutions for their individual needs. Together we set standards in Industrial Connectivity. Weidmüller Interface GmbH & Co. KG Klingenbergstraße 16 32758 Detmold, Germany T +49 5231 14-0 F +49 5231 14-292083 [email protected] www.weidmueller.com Your local Weidmüller partner can be found on our website: www.weidmueller.com/countries Order number: 1437900000/04/2013/SMDM