LT5524 - Low Distortion IF Amplifier/ADC Driver with Digitally Controlled Gain

LT5524
Low Distortion IF
Amplifier/ADC Driver with
Digitally Controlled Gain
U
FEATURES
DESCRIPTIO
■
The LT®5524 is a programmable gain amplifier (PGA) with
bandwidth extending from low frequency (LF) to 540MHz.
It consists of a digitally controlled variable attenuator,
followed by a high linearity amplifier. Four parallel digital
inputs control the gain over a 22.5dB range with 1.5dB
step resolution. An on-chip power supply regulator/filter
helps isolate the amplifier signal path from external noise
sources.
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Output IP3 at 100MHz: 40dBm
Maximum Output Power: 16dBm
Bandwidth: LF to 540MHz
Propagation Delay: 0.8ns
Maximum Gain: 27dB
Gain Control Range: 22.5dB
Gain Control Step: 1.5dB
Gain Control Settling Time: 500ns
Noise Figure: 8.6dB at 100MHz (Max Gain)
Output Noise Floor: –138dBm/Hz (Max Gain)
Reverse Isolation: –92dB
Single Supply: 4.75V to 5.25V
Shutdown Mode
Enable/Disable Time: 1µs
Differential I/O Interface
20-Lead TSSOP Package
The LT5524’s open-loop architecture offers stable operation for any practical load conditions, including peakingfree AC response when driving capacitive loads, and
excellent reverse isolation.
The LT5524 may be operated broadband, where the output differential RC time constant sets the bandwidth, or it
may be used as a narrowband driver with the appropriate
output filter.
U
APPLICATIO S
■
■
■
■
High Linearity ADC Driver
IF Sampling Receivers
VGA IF Power Amplifier
50Ω Driver
Instrumentation Applications
U
■
, LTC and LT are registered trademarks of Linear Technology Corporation.
Patents Pending.
TYPICAL APPLICATIO
Output IP3 vs Frequency, ROUT = 200Ω
54
5V
CHOKE
RF
INPUT
IF
BPF
LO
IF
AMP
48
0.1µF
100Ω
LT5524
0.1µF
0.1µF
GAIN CONTROL
ADC
5524 TA01
OIP3 (dBm)
0.1µF
51
CHOKE
45
MAX GAIN
42
39
1.5dB
ATTENUATION
STEP
36
4 LINES
33
30
0
50
100
150
200
FREQUENCY (MHz)
5524 TA02
5524f
1
LT5524
U
W
W W
U
U
W
ABSOLUTE MAXIMUM RATINGS
PACKAGE/ORDER INFORMATION
(Notes 1, 2)
Power Supply Voltage (VCC1, VCC2) .......................... 6V
Output DC Voltage (OUT+, OUT–) ............................. 7V
Control Input Voltage (EN, PGAx) ............. –0.5V to VCC
Signal Input Voltage (IN+, IN–) ................... –0.5V to 3V
Operating Ambient Temperature Range .. – 40°C to 85°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
TOP VIEW
EN 1
20 NC
VCC1 2
19 VCC2
GND 3
18 GND
GND 4
17 GND
IN +
5
IN –
6
21
ORDER PART
NUMBER
LT5524EFE
16 OUT –
15 OUT +
GND 7
14 GND
GND 8
13 GND
PGA0 9
12 PGA3
PGA1 10
11 PGA2
FE PACKAGE
20-LEAD PLASTIC TSSOP
TJMAX = 150°C, θJA = 38°C/W
EXPOSED PAD (PIN 21) IS GND
MUST BE SOLDERED TO PCB
Consult LTC Marketing for parts specified with wider operating temperature ranges.
U
U
WW
PROGRA
ABLE GAI SETTI GS
ATTENUATION STEP
RELATIVE TO MAX GAIN
1
0dB
2
–1.5dB
3
–3.0dB
4
–4.5dB
5
–6.0dB
6
–7.5dB
7
–9.0dB
8
–10.5dB
9
–12.0dB
10
–13.5dB
11
–15.0dB
12
–16.5dB
13
–18.0dB
14
–19.5dB
15
–21.0dB
16
–22.5dB
*ROUT = 200Ω
PGA0
High
Low
High
Low
High
Low
High
Low
High
Low
High
Low
High
Low
High
Low
PGA1
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
High
High
Low
Low
PGA2
High
High
High
High
Low
Low
Low
Low
High
High
High
High
Low
Low
Low
Low
PGA3
High
High
High
High
High
High
High
High
Low
Low
Low
Low
Low
Low
Low
Low
POWER GAIN*
27.0dB
25.5dB
24.0dB
22.5dB
21.0dB
19.5dB
18.0dB
16.5dB
15.0dB
13.5dB
12.0dB
10.5dB
9.0dB
7.5dB
6.0dB
4.5dB (Note 3)
5524f
2
LT5524
DC ELECTRICAL CHARACTERISTICS VCC = 5V, VCCO = 5V, EN = 3V, TA = 25°C, unless otherwise noted.
(Note 7) (Test circuits shown in Figures 9 and 10)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
4.75
5
5.25
V
3
5
5.5
V
1.15
1.3
Normal Operating Conditions
VCC
Supply Voltage (Pins 2, 19)
(Note 4)
VCCO
OUT+, OUT– Output Pin DC Common Mode Voltage
OUT+, OUT–
Connected to VOSUP via
Choke Inductors or Resistors (Note 5)
Shutdown DC Characteristics, EN = 0.6V
VIN(BIAS)
IN+, IN– Bias Voltage
Max Gain (Note 6)
1.5
V
IIL(PGA)
PGAO, PGA1, PGA2, PGA3 Input Current
VIN = 0.6V
20
µA
IIH(PGA)
PGAO, PGA1, PGA2, PGA3 Input Current
VIN = 5V
20
µA
IOUT
OUT+, OUT– Current
All Gain Settings
ICC
VCC Supply Current
All Gain Settings (Note 4)
44
20
µA
100
µA
0.6
V
Enable and PGA Inputs DC Characteristics
VIL
EN and PGAx Input Low Voltage
x = 0, 1, 2, 3
VIH
EN and PGAx Input High Voltage
x = 0, 1, 2, 3
IIL(PGA)
PGAO, PGA1, PGA2, PGA3 Input Current
VIN = 0.6V
IIH(PGA)
PGAO, PGA1, PGA2, PGA3 Input Current
VIN = 3V and 5V
IIL(EN)
EN Input Current
VIN = 0.6V
IIH(EN)
EN Input Current
VIN = 3V
VIN = 5V
3
V
20
µA
15
30
µA
4
20
µA
18
38
100
µA
µA
1.48
1.65
V
DC Characteristics, EN = 3V
VIN(BIAS)
IN+, IN– Bias Voltage
RIN
Input Differential Resistance
All Gain Settings (DC)
122
Ω
gm
Amplifier Transconductance
Max Gain
0.15
S
IOUT
OUT+, OUT– Quiescent Current
All Gain Settings, VOUT = 5V
Max Gain (Note 6)
1.34
17
20
24
mA
IOUT(OFFSET) Output Current Mismatch
All Gain Settings, IN+, IN–
ICC
VCC1 + VCC2 Supply Current
Max Gain (Note 4)
Min Gain (Note 4)
34
36
40
43
mA
mA
ICC(TOTAL)
Total Supply Current
ICC + 2 • IOUT (Max Gain)
75
91
mA
Open
100
µA
5524f
3
LT5524
AC ELECTRICAL CHARACTERISTICS VCC = 5V, VCCO = 5V, EN = 3V, TA = 25°C, ROUT = 200Ω. Maximum gain
specifications are with respect to differential inputs and differential outputs, unless otherwise noted.
(Note 7) (Test circuits shown in Figures 9 and 10)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Dynamic Performance
BW
Large-Signal –3dB Bandwidth
VOUT(CLIP) Output Voltage Clipping Levels
All Gain Settings (Note 8), ROUT = 100Ω
Each OUT+, OUT– with Respect to Ground
LF to 540
2
MHz
8
V
(Note 11)
POUT(MAX) Clipping Limited Maximum Sinusoidal
Output Power
All Gain Settings, Single Tone,
fIN = 100MHz (Note 10)
16
dBm
gm
Amplifier Transconductance
Max Gain, fIN = 100MHz
0.15
S
S12
Reverse Isolation
fIN = 100MHz (Note 9)
–92
dB
Output Third Order Intercept Point for
PGA0 = High (PGA1, PGA2, PGA3 Any State)
POUT = 4dBm (Each Tone), 200kHz Tone Spacing,
fIN = 100MHz
+40
dBm
Output Third Order Intercept Point for
PGA0 = Low (PGA1, PGA2, PGA3 Any State)
POUT = 4dBm (Each Tone), 200kHz Tone Spacing,
fIN = 100MHz
+36
dBm
Distortion and Noise
OIP3
HD2
Second Harmonic Distortion
POUT = 5dBm (Single Tone), fIN = 50MHz
–76
dBc
HD3
Third Harmonic Distortion
POUT = 5dBm (Single Tone), fIN = 50MHz
–72
dBc
NFLOOR
Output Noise Floor
(PGAO, PGA2, PGA3 Any State)
PGA1 = High, fIN = 100MHz
PGA1 = Low, fIN = 100MHz
–138
–140
dBm/Hz
dBm/Hz
NF
Noise Figure
Max Gain Setting, fIN = 100MHz
8.6
dB
PGA Settling Time
Output Settles within 10% of Final Value
500
ns
Enable/Disable Time
Output Settles within 10% of Final Value
600
ns
27
dB
Amplifier Power Gain and Gain Step
GMAX
Maximum Gain
fIN = 20MHz and 200MHz
GMIN
Minimum Gain
fIN = 20MHz and 200MHz
GSTEP
Gain Step Size
fIN = 20MHz and 200MHz
Gain Step Accuracy
fIN = 20MHz and 200MHz
4.5
0.8
1.5
dB
2.2
dB
±0.2
dB
Amplifier I/O Impedance (Parallel Values, Specified Differentially)
RIN
Input Resistance
fIN = 100MHz
122
Ω
CIN
Input Capacitance
fIN = 100MHz
2
pF
RO
Output Resistance
fIN = 100MHz
5
kΩ
CO
Output Capacitance
fIN = 100MHz
1.7
pF
Note 1: Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2: All voltage values are with respect to ground.
Note 3: Default state for open PGA inputs.
Note 4: VCC1 and VCC2 (Pins 2 and 19) are internally connected.
Note 5: External VOSUP is adjusted such that VCCO output pin common
mode voltage is as specified when resistors are used. For choke inductors
or transformer, VOSUP = VCCO = 5V typ.
Note 6: Internally generated common mode input bias voltage requires
capacitive or transformer coupling to the signal source.
Note 7: Specifications over the –40°C to 85°C operating temperature
range are assured by design, characterization and correlation with
statistical process controls. Gain always refers to power gain. Input
matching is assumed. PIN is the available input power. POUT is the power
into the external load, ROUT, as seen by the LT5524 differential outputs. All
dBm figures are with respect to 50Ω.
Note 8: High frequency operation is limited by the RC time constants at
the input and output ports. The low frequency (LF) roll-off is set by I/O
interface choice.
Note 9: Limited by package and board isolation.
Note 10: See “Clipping Free Operation” in the Applications Information
section. Refer to Figure 7.
Note 11: Although the instantaneous AC voltage on the OUT+ or OUT– pins
may in some situations safely exceed 8V (with respect to ground), in no
case should the DC voltage on these pins be allowed to exceed the
ABSMAX tested limit of 7V.
5524f
4
LT5524
U W
TYPICAL PERFOR A CE CHARACTERISTICS
TA = 25°C, VCC = 5V, VCCO = 5V, EN = 3V, control
input levels VIL = 0.6V, VIH = 3V unless otherwise noted. (Test circuit shown in Figure 9)
Gain Error vs Attenuation Step at
25MHz, ROUT = 200Ω
Frequency Response for All Gain
Steps, ROUT = 200Ω
30
0.8
27
0.8
25°C
–40°C
85°C
0.6
24
15
12
9
0.4
GAIN ERROR (dB)
18
25°C
–40°C
85°C
0.6
0.4
21
GAIN ERROR (dB)
POWER GAIN (dB)
Gain Error vs Attenuation Step at
100MHz, ROUT = 200Ω
0.2
0
–0.2
0.2
0
–0.2
–0.4
–0.4
–0.6
–0.6
6
3
–0.8
0
100
FREQUENCY (MHz)
10
0
1000
3
12 15
6
9
18
ATTENUATION STEP (dB)
5524 G01
Maximum Gain vs VCC at
120MHz, ROUT = 200Ω
25
5.2
27.4
20
27.2
–40°C
85°C
27.0
25°C
26.8
4.4
26.6
4.2
26.4
4.9
5.1
4.7
4.9
5.1
5.5
5.3
VCC (V)
–5
–31 –28 –25 –22 –19 –16 –13 –10
PIN (dBm)
OIP3 vs Frequency at Pin = –23dBm,
Max Gain and 1.5dB Attenuation
Step, ROUT = 200Ω
–7
5524 G06
5524 G05
5524 G04
Harmonic Distortion vs POUT at
50MHz, Max Gain, ROUT = 200Ω
–40
54
–45
51
–50
–55
48
–60
HD(dBc)
45
MAX GAIN
42
39
–65
HD3
–70
HD2
–75
–80
1.5dB
ATTENUATION
STEP
36
–85
HD5
–90
33
30
ROUT = 200Ω
0
26.2
4.5
5.5
5.3
10
5
85°C
VCC (V)
OIP3 (dBm)
4.7
POUT (dBm)
GAIN (dB)
25°C
21
15
–40°C
4.8
4.0
4.5
12 15
6
9
18
ATTENUATION STEP (dB)
POUT vs PIN at 50MHz, Max Gain
27.6
4.6
3
5524 G03
5.4
5.0
0
5524 G02
Minimum Gain vs VCC at 120MHz,
ROUT = 200Ω
GAIN (dB)
–0.8
21
HD4
–95
–100
0
50
100
150
200
FREQUENCY (MHz)
5524 G07
–6
–3
0
6
3
POUT (dBm)
9
12
15
5524 G08
5524f
5
LT5524
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Two tones, 200kHz spacing, TA = 25°C, EN = 3V,
VCC = 5V, VCCO = 5V, control input levels VIL = 0.6V, VIH = 3V unless otherwise noted. (Test circuit shown in Figure 10)
NF vs Attenuation Step at
Freq = 100MHz
Noise Figure vs Frequency
Output Noise Floor vs Attenuation
Step, Freq = 100MHz, ROUT = 200Ω
–136
30
10.0
27
9.5
8.5
15
9
3dB ATTENUATION STEP
(PGA1 = LOW)
7.5
18
12
MAX GAIN
8.0
NOISE FLOOR (dBm/Hz)
21
NF (dB)
NF (dB)
9.0
–137
24
1.5dB ATTENUATION STEP
(PGA0 = LOW)
6
PGA1 = HIGH
–138
–139
PGA1 = LOW
–140
–141
3
7.0
0
50
0
100 150 200 250 300 350 400
FREQUENCY (MHz)
–142
0
3
6
9
12
18
15
ATTENUATION STEP (dB)
5524 G09
21
0
3
6
9
12 15 18
ATTENUATION STEP (dB)
5524 G11
5524 G10
Pulse Response vs Output Level at
Max Gain. Indicated Voltage Levels
are into 50Ω External Load
21
Single-Ended Output Current
vs Attenuation Step
VIN(BIAS) vs Attenuation Step
21.0
1.60
20.5
1.55
CURRENT (mA)
2VP-P
1.5VP-P
1VP-P
INPUTS
20.0
VIN(BIAS) (V)
COUT = 0.82pF
85°C
1.50
–40°C
1.45
85°C
25°C
25°C
19.5
–40°C
19.0
2ns/DIV
5524 G12
1.40
0
6
9
12 15 18
ATTENUATION STEP (dB)
3
21
0
6
9
12 15 18
ATTENUATION STEP (dB)
3
5524 G14
5524 G13
ICC Shutdown Current vs VCC,
EN = 0.6V
Total ICC vs Attenuation Step
70
78
85°C
75
25°C
60
85°C
50
CURRENT (µA)
CURRENT (mA)
80
73
–40°C
70
25°C
40
30
–40°C
20
68
65
21
10
0
3
6
9
12 15 18
ATTENUATION STEP (dB)
21
0
4.5
4.7
4.9
5.1
5.3
5.5
INPUT VCC (V)
5524 G15
5524 G16
5524f
6
LT5524
U
U
U
PI FU CTIO S
EN (Pin 1): Enable Pin for Amplifier. When the input
voltage is higher than 3V, the amplifier is turned on. When
the input voltage is less than or equal to 0.6V, the amplifier
is turned off. This pin is internally pulled to ground if not
connected.
PGA2 (Pin 11): Amplifier PGA Control Input Pin for the 6dB
Attenuation Step (see Programmable Gain table). Input is
high when the input voltage is greater than 3V. Input is low
when the input voltage is less than or equal to 0.6V. This
pin is internally pulled to ground if not connected.
VCC1 (Pin 2): Power Supply. This pin is internally connected
to VCC2 (Pin 19). Decoupling capacitors (1000pF and 0.1µF
for example) may be required in some applications.
PGA3 (Pin 12): Amplifier PGA Control Input Pin for 12dB
Attenuation Step (see Programmable Gain table). Input is
high when the input voltage is greater than 3V. Input is low
when the input voltage is less than or equal to 0.6V. This
pin is internally pulled to ground if not connected.
GND (Pins 3, 4, 7, 8, 13, 14, 17, 18): Ground.
IN+ (Pin 5): Positive Signal Input Pin with Internal DC
Bias.
OUT+ (Pin 15): Positive Amplifier Output. A transformer
with center tap tied to VCC or a choke inductor is recommended to source the DC quiescent current.
IN– (Pin 6): Negative Signal Input Pin with Internal DC
Bias.
OUT– (Pin 16): Negative Amplifier Output. A transformer
with center tap tied to VCC or a choke inductor is recommended to source the DC quiescent current.
PGA0 (Pin 9): Amplifier PGA Control Input Pin for the 1.5dB
Attenuation Step (see Programmable Gain table). Input is
high when the input voltage is greater than 3V. Input is low
when the input voltage is less than or equal to 0.6V. This
pin is internally pulled to ground if not connected.
VCC2 (Pin 19): Power Supply. This pin is internally connected to VCC1 (Pin 2).
NC (Pin 20): Not Connected.
PGA1 (Pin 10): Amplifier PGA Control Input Pin for the 3dB
Attenuation Step (see Programmable Gain table). Input is
high when the input voltage is greater than 3V. Input is low
when the input voltage is less than or equal to 0.6V. This
pin is internally pulled to ground if not connected.
Exposed Pad (Pin 21): Ground. This pin must be soldered
to the printed circuit board ground plane for good heat
transfer.
W
BLOCK DIAGRA
LT5524
5
6
IN+
ATTENUATOR
IN–
RIN
100Ω
VOLTAGE REGULATOR
AND BIAS
GND (3, 4, 7, 8
13, 14, 17, 18)
VCC1
2
VCC2
19
OUT –
OUT+
GAIN CONTROL
LOGIC
PGA3
12
16
AMPLIFIER
ENABLE
CONTROL
PGA2 PGA1
11
10
15
PGA0
9
NC
20
EN
1
21
5524 F01
Figure 1. Functional Block Diagram
5524f
7
LT5524
U
W
U U
APPLICATIO S I FOR ATIO
Circuit Operation
The LT5524 is a high linearity amplifier with high impedance output (Figure 1). It consists of the following
sections:
• An input variable attenuator “gain-control” block with
122Ω input impedance
• A differential transconductance amplifier, with enable
input
• An internal bias block with internal voltage regulator
• A gain control logic block
The LT5524 amplifier provides amplification with very low
distortion using a linearized open-loop architecture. In
contrast with high linearity amplifiers employing negative
feedback, the LT5524 offers:
where:
gm is the LT5524 transconductance = 0.15S.
RIN is the LT5524 differential input impedance ≅ 122Ω.
Input impedance matching is assumed.
ROUT is the external differential output impedance as
seen by the LT5524’s differential outputs. ROUT should
be distinguished from the actual load impedance, RLOAD,
which will typically be coupled to the LT5524 output by
an impedance transformation network.
The power gain as a function of ROUT is plotted in Figure 2.
The ideal relationship is linear. The curved line indicates
the roll-off due to the finite (noninfinite) output resistance
of the LT5524.
45
• Stable operation for any practical load
40
• A capacitive output reactance (not inductive) that provides peaking free AC response to capacitive loads
35
The LT5524 is a transconductance amplifier and its operation can be understood conceptually as consisting of two
steps: First, the input signal voltage is converted to an
output current. The intermodulation distortion (in dBc) of
the LT5524 output current is determined by the input
signal level, and is almost independent of the output load
conditions. Thus, the LT5524’s input IP3 is also nearly
independent of the output load.
Next, the external output load (ROUT) converts the output
current to output voltage (or power). The LT5524’s voltage and power gain both increase with increasing ROUT.
Accordingly, the output power and output IP3 also increase with increasing ROUT. The actual output linearity
performance in the application will thus be set by the
choice of output load, as well as by the output network.
Maximum Gain Calculation
The maximum power gain (with the 0dB attenuation step)
is:
GAIN (dB)
• Exceptional reverse isolation of –100dB at 50MHz and
–78dB at 300MHz (package and board leakage limited)
30
25
20
15
10
IDEAL
WITH RO
5
0
20
100
1000 2000
ROUT (Ω)
5524 F02
Figure 2. Power Gain as a Function of ROUT
The actual available output power (as well as power gain
and OIP3) will be reduced by losses in the output interface,
consisting of:
• The insertion loss of the output impedance transformation network (for example the transformer insertion
loss in Figure 6)
• About –3dB loss if a matching resistor (RMATCH in
Figure 6) is used to provide output load impedance
back-matching (for example when driving transmission lines)
GPWR(dB) = 10 • log(gm2 • RIN • ROUT)
5524f
8
LT5524
U
W
U U
APPLICATIO S I FOR ATIO
VOSUP
Input Interface
C3
For the lowest noise and highest linearity, the LT5524
should be driven with a differential input signal. Singleended drive will severely degrade linearity and noise
performance.
• Match the source impedance to the LT5524, RIN ≅ 122Ω
• Provide well balanced differential input drive (capacitor
C2 in Figure 4)
• Minimize insertion loss to avoid degrading the noise
figure (NF)
RLOAD
50Ω
C2
RLOAD
50Ω
ROUT
+
LT5524 F05
Figure 5. Output Impedance-Matched
and Capacitively Coupled to a Differential Load
Input matching network design criteria are:
• DC block the LT5524 internal bias voltage (see Input
Bias Voltage section for DC coupling information)
R2
51Ω C1
–
RIN
122Ω
IN–
Example input matching networks are shown in Figures 3
and 4.
R1
51Ω
LT5524
IN+
Note: In Figure 5, (choke) inductors may be placed in
parallel with or used to replace resistors R1 and R2, thus
eliminating the DC voltage drop across these resistors.
VOSUP
IN+
IN–
LT5524
–
RIN
122Ω
C1
RMATCH
255Ω
(OPTIONAL)
ROUT
+
RLOAD
50Ω
T2
4:1
•
•
•
LT5524 F06
R1
50Ω
C1
VSRC R2
50Ω
C2
LT5524
IN+
Figure 6. Output Impedance-Matched and
Transformer-Coupled to a Single-Ended Load
–
RIN
122Ω
IN–
+
LT5524 F03
Figure 3. Input Capacitively-Coupled to a Differential Source
RSRC
50Ω
T1
1:2
•
VSRC
IN+
•
•
IN–
C2
0.33µF
• Provide DC isolation between the LT5524 DC output
voltage and RLOAD.
• Provide a path for the output DC current from the output
voltage source VOSUP.
LT5524
–
RIN
122Ω
+
Output network design criteria are:
LT5524 F04
Figure 4. Input Transformer-Coupled to a Single-Ended Source
Output Interface
The output interface network provides an impedance
transformation between the actual load impedance, RLOAD,
and the LT5524 output loading, ROUT, chosen to maximize
power or linearity, or to minimize output noise, or for some
other criteria as explained in the following sections.
Two examples of output matching networks are shown in
Figures 5 and 6 (as implemented in the LT5524 demo
boards).
• Provide an impedance transformation, if required, between the load impedance, RLOAD, and the optimum
ROUT loading.
• Set the bandwidth of the output network.
• Optional: Provide board output impedance matching
using resistor RMATCH (when driving a transmission
line).
• Use high linearity passive parts to avoid introducing
noninearity.
Note that there is a noise penalty of up to 6dB when using
power delivered by only one output in Figure 5.
5524f
9
LT5524
U
W
U U
APPLICATIO S I FOR ATIO
Clipping Free Operation
To avoid current clipping, the output signal current should
not exceed the DC quiescent current, IOUT = 20mA (typical). Correspondingly, the maximum input voltage,
VIN(MAX), is IOUT/gm = 133mV (peak). In power terms,
PIN(MAX) = –11.5dBm (assuming RIN = 122Ω).
To avoid output voltage clipping (due to LT5524 output
stage saturation or breakdown), the single-ended output
voltage swing should stay within the specified limits; i.e.,
2V ≤ VOUT ≤ 8V. For a DC output bias of 5V, the maximum
single ended swing will be 3Vpeak and the maximum
differential swing will be 6Vpeak. The simultaneous onset
of both current and voltage limiting occurs when ROUT =
6Vpeak/20mA = 300Ω (typ) for a maximum POUT =
17.8dBm. This calculation applies for a sinusoidal signal.
For nonsinusoidal signals, use the appropriate crest factor to calculate the actual maximum power that avoids
output clipping.
Although the instantaneous AC voltage on the OUT+ or
OUT– pins may in some situations safely exceed 8V (with
respect to ground), in no case should the DC voltage on
these pins be allowed to exceed the ABSMAX tested limit
of 7V.
For nonoptimal ROUT values, the maximum available output power will be lower and can be calculated (considering
current limiting for ROUT < 300Ω, and voltage limiting for
ROUT > 300Ω). The result of this calculation is shown in
Figure 7.
The LT5524 input should not be overdriven (PIN >
–11.5dBm at maximum gain). The consequences of overdrive are reduced bandwidth and, when the frequency is
greater than 50MHz, reduced output power. At reduced
gain settings, the maximum PIN is increased by an amount
equal to the gain reduction.
Input Bias Voltage
The LT5524 IN+, IN– signal inputs are internally biased to
1.48V common mode when enabled, and to 1.26V in
VCC = VCCO = 5V
CURRENT
LIMIT
20
POUT(MAX) (dBm)
The LT5524 is a class A amplifier. To avoid signal distortion, the user must ensure that the LT5524 outputs do not
enter into current or voltage limiting. The following discussion applies to maximum gain operation.
25
VOLTAGE
LIMIT
15
10
5
0
20
100
1000 2000
ROUT (Ω)
5524 F07
Figure 7. Maximum Output Power as a Function of ROUT
shutdown mode. These inputs are typically coupled by
means of a capacitor or a transformer to a signal source,
and impedance matching is assumed. In shutdown mode,
the internal bias can handle up to 1µA leakage on the input
coupling capacitors. This reduces the turn-on delay due to
the input coupling RC time constant when exiting shutdown mode.
If DC coupling to the input is required, the external
common mode bias should track the LT5524’s internal
common mode level. The DC current from the LT5524
inputs should not exceed IIN(SINK) = –200µA and IIN(SOURCE)
= 400µA.
Stability Considerations
The LT5524’s open-loop architecture allows it to drive any
practical load. Note that LT5524 gain is proportional to the
load impedance, and may exceed the reverse isolation at
frequencies above 1GHz if the LT5524’s outputs are left
unloaded, with instability as the undesirable consequence.
In such cases, placing a resistive differential load (e.g., 4k)
or a small capacitor at the LT5524 outputs can be used to
limit the maximum gain.
The LT5524 has about 20GHz gain-bandwidth product.
Hence, attention must be paid to the printed circuit board
layout to avoid output pin to input pin signal coupling (the
evaluation board layout is a good example). Due to the
LT5524’s internal power supply regulator, external supply
decoupling capacitors typically are not required. Likewise,
decoupling capacitors on the LT5524 control inputs typically are not needed. Note, however, that the Exposed Pad
5524f
10
LT5524
U
W
U U
APPLICATIO S I FOR ATIO
on the LT5524 package must be soldered to a good ground
plane on the PCB.
PGA Function, Linearity and NF
As described in the Circuit Operation section, the LT5524
consists of a variable (step) attenuator followed by a high
gain output amplifier. The overall gain of the LT5524 is
digitally controlled by means of four gain control pins with
internal pull-down. Minimum gain is programmed when
the gain control pins are set low or left floating. In
shutdown mode, these PGA inputs draw <10µA leakage
current, regardless of the applied voltage.
The 6dB and 12dB attenuation steps (PGA2 and PGA3) are
implemented by switching the amplifier inputs to an input
attenuator tap. The 3dB attenuation step (PGA1) changes
the amplifier transconductance. The output IP3 is approximately independent of the PGA1, PGA2 and PGA3 gain
settings. However, the 1.5dB attenuation step utilizes a
current steering technique that disables the internal linearity compensation circuit, and the OIP3 can be reduced by
as much as 6dB when PGA0 is low. Therefore, to achieve
the LT5524’s highest linearity performance, the PGA0 pin
should be set high.
The LT5524 noise figure is 8.6dB at 100MHz in the maximum gain state. For the –3dB attenuation setting, the NF
is 9.2dB. The noise figure increases in direct proportion to
the amount of programmed gain reduction for the 1.5dB,
6dB and 12dB steps.
The output noise floor is proportional to the output load
impedance, ROUT. It is almost constant for PGA1 = high
and for any PGA0, PGA2, PGA3 state. When PGA1 = low,
the output noise floor is 2dB lower (see Typical Performance Characteristics).
Other Linearity Considerations
LT5524 linearity is a strong function of signal frequency.
OIP3 decreases about 13dB for every octave of frequency
increase above 100MHz.
As noted in the Circuit Operation section, at any given
frequency and input level, the LT5524 provides a current
output with fairly constant intermodulation distortion figure in dBc, regardless of the output load value. For higher
ROUT values, more gain and output power is available, and
better OIP3 figures can be achieved. However, high ROUT
values are not easily implemented in practice, limited by
the availability of high ratio output impedance transformation networks.
Linearity can also be limited by the output RC time constant (bandwidth limitations), particularly for high ROUT
values. A solution is outlined in the Bandpass Applications
section.
The LT5524 linearity degrades when common mode signal is present. The input transformer center tap should be
decoupled to ground to provide a balanced input differential signal and to avoid linearity degradation for high
attenuation steps. When the signal frequency is lower than
50MHz, and there is significant common mode signal,
then high attenuation settings may result in degraded
linearity.
At signal frequencies below 100MHz, the LT5524’s internal linearity compensation circuitry may provide “sweet
spots” with very high OIP3, in excess of +52dBm. This
almost perfect distortion correction cannot be sustained
over the full operating temperature range and with variations of the LT5524 output load (complex impedance
ZOUT). Users are advised to rely on data shown in the
Typical Performance Characteristics curves to estimate
the dependable linearity performance.
Wideband Applications
At low frequencies, the value of the decoupling capacitors,
choke inductors and choice of transformer will set the
minimum frequency of operation. Output DC coupling is
possible, but this typically reduces the LT5524’s output
DC bias voltage, and thus the output swing and available
power.
At high frequencies, the output RC time constants set an
upper limit to the maximum frequency of operation in the
case of the wideband output networks presented so far.
For example the LT5524 output capacitance, COUT = 1.7pF,
and a pure resistive load, ROUT = 200Ω, will set the –3dB
bandwidth to about 400MHz. In an actual application, the
RLOAD • CLOAD product may be even more restrictive. The
use of wideband output networks will not only limit the
5524f
11
LT5524
U
W
U U
APPLICATIO S I FOR ATIO
bandwidth, but will also degrade linearity because part of
the available power is wasted driving the capacitive load.
The LT5524’s output reactance is capacitive. Therefore
improved AC response is possible by using external series
output inductors. When driving purely resistive loads, an
inductor in series with the LT5524 output may help to
achieve maximally flat AC response as exemplified in the
characterization setup schematic (Figure 9).
The series inductor can extend the application bandwidth,
but it provides no improvement in linearity performance.
Series inductance may also produce peaking in the AC
response. This can be the case when (high Q) choke
inductors are used in an output interface such as in
Figure 5, and the PCB trace (connection) to the load is too
long. Since the LT5524’s output impedance is relatively
high, the PCB trace acts as a series inductor. The most
direct solution is to shorten the connection lines by
placing the driver closer to the load. Another solution to
flatten the AC response is to place resistance close to the
LT5524 outputs. In this way the connection line behaves
more like a terminated transmission line, and the AC
peaking due to the capacitive load can be removed.
Bandpass Applications
For narrow band IF applications, the LT5524’s output
capacitance and the application load capacitance can be
incorporated as part of an LC impedance transformation
network, giving improved linearity performance for signal
frequencies greater than 100MHz. Figure 8 is an example
of such a network.
The network consists of two parallel resonant LC tank
circuits critically coupled by capacitors C1 and C2. The
ROUT to RLOAD transformation ratio in this particular
implementation is 2. The choice of impedance transformation ratio is more flexible than in the wideband case.
The LC network is a bandpass filter, a useful feature in
many applications.
A variety of bandpass matching network configurations
are conceivable, depending on the requirements of the
particular application. The design of these networks is
facilitated by the fact that the LT5524 outputs are not
destabilized by reactive loading.
Note that these LC networks may distort the output signal
if their amplitude and phase response exhibit nonlinear
behavior. For example, if resistors R1 and R2 in Figure 5
are replaced with LC resonant tank circuits, then severe
OIP3 degradation may occur.
Low Output Noise Floor Applications
In some applications the maximum output noise floor is
specified. The LT5524 output noise floor is elevated above
the available noise power (–174dBm/Hz into 50Ω) by the
NF + Gain. Consequently, reduction of the LT5524’s power
gain is the only way to reduce the output noise floor.
NOTE:
C3 + CLOAD = 12pF
C4 + CLOAD = 12pF
VCC
T1
1:2
L5
56nH
C8
0.1µF
IN+
VSRC
TC2-1T
C9
0.33µF
IN–
C3
LT5524
+
ROUT
200Ω
C6
2.2pF
C2
12pF
C5
5.6pF L4
56nH
RLOAD
100Ω
C4
GAIN = 27dB
PGA0 PGA1 PGA2 PGA3
L3
56nH
–
DUT
RSRC
50Ω
L6
C1
56nH 12pF
VOSUP
C7
0.1µF
RLOAD
50Ω
CLOAD
RLOAD
50Ω
CLOAD
1dB BANDWIDTH:
fL = 130MHz
fU = 220MHz
5524 F08
Figure 8. Bandpass Output Transformation Network Example
5524f
12
LT5524
U
W
U U
APPLICATIO S I FOR ATIO
Rather, it represents a compromise that most accurately
measures the actual operation of the part by itself,
undistorted by the artifacts of the impedance transformation
network, or by external bandwidth limiting factors. Balun
transformers are used to interface with single-ended test
equipment. Input and output resistive attenuators (not
shown) provide broadband I/O impedance control. The
L1, L2 inductors are selected for maximally flat AC output
response. COUT (normally open) shows the placement of
capacitive loading when this is specified as a
characterization variable. The VCCO monitor pin allows
setting the output DC level (5V typical) by adjusting
voltage VOSUP.
In fixed gain applications, the LT5524 can be set to 3dB
attenuation relative to maximum gain. As shown in the
Typical Performance Characteristics, this gives a 2dB
reduction in the output noise floor with no loss of linearity.
In general, the output noise floor can be reduced by
decreasing ROUT (and hence power gain), at the cost of
reduced OIP3.
LT5524 Characterization
The LT5524’s typical performance data are based on the
test circuits shown in Figures 9 and 10. Figure 9 does not
necessarily reflect the use of the LT5524 in an actual
application. (For that, see the Application Boards section.)
VCC
R9
35.7Ω
C1
0.33µF
C7
47nF
T1
1:1
RSRC
50Ω
VSRC
R10
35.7Ω
C2
0.1µF
COUT
(OPT)
R7
35.7Ω
C8
47nF
IN+
R8
35.7Ω
LT5524
IN–
ROUT
+
R5
51k
R6
51k
R3
37.4Ω
L2
(OPT)
R4
37.4Ω
C5
47nF
T1
1:1
C6
47nF
RLOAD
50Ω
COUT
(OPT)
VCCO
MONITOR
PGA0 PGA1 PGA2 PGA3
L1
(OPT)
VOSUP
C3
4.7µF
C4
0.1µF
R2
25Ω
–
DUT
ATT =
7.7dB
ETC-11-13
R1
25Ω
ETC-11-13
ROUT R3, R4 ATT L1, L2
100Ω 37.4Ω 9dB 0Ω
200Ω 87.4Ω 12dB 33nH
5524 F09
Figure 9. Characterization Board (Simplified Schematic)
VCC
C2
0.1µF
IF
IN
T1
1:2
C1
0.47µF
J1
0Ω TC2-1T
TRANSFORMER DEMO BOARD
EN
1
2
3
4
5
6
7
8
9
10
PGA0 PGA1
VOSUP
EN
NC
VCC1
VCC2
GND
GND
LT5524
GND
GND
IN+
OUT–
IN–
OUT+
GND
GND
GND
GND
PGA0
PGA3
PGA1
PGA2
20
NC
19
18
17
16
15
14
13
12
11
C4
0.1µF
C3
4.7µF
IF
OUT
T2
4:1
ROUT
100Ω
•
•
RMATCH
255Ω
•
TC4-1W
RLOAD
50Ω
J2
0Ω
PGA2 PGA3
5524 F10
Figure 10. Output Transformer Application Board (Simplified Schematic)
5524f
13
LT5524
U
W
U U
APPLICATIO S I FOR ATIO
Application (Demo) Boards
(T2 transformer). For the Typical Performance Characteristics curves, all linearity tests are performed on this
board. By removing RMATCH, the performance with ROUT
= 200Ω can be evaluated (provided the lack of impedance
back-matching is suitably remedied).
The LT5524 demo boards are provided in the versions
shown in Figure 10 (with output transformer) and Figure 11 (without output transformer). All I/O signal ports
are matched to 50Ω. Moreover, 40k resistors (not shown)
connect all five control pins (EN, PGA0, PGA1, PGA2,
PGA3) to VCC, such that the LT5524 is shipped in maximum gain state.
The transformer board can provide a differential output
when Jumper J2 is removed.
The Wideband Differential Output Application Board (Figure 11) is an example of direct coupling (no transformer)
to the load, and has wider output bandwidth. This board
gives direct access to the LT5524’s output pins, and was
used for stability tests. Higher VOSUP (6.5V) is required to
compensate for the DC voltage drop on R1 and R2. Use
TP2, TP3 to monitor the actual LT5524 output bias voltage. By replacing R1 and R2 with inductors, this board can
operate with a 5V supply. However, this may limit the
minimum signal frequency. For example, an 820nH choke
inductor will limit the lowest signal frequency to 40MHz.
The gain setting can be changed by connecting the control
pins to ground. Test points (TP1, TP2, TP3) are provided
to monitor the input and output DC bias voltage. Jumper
J1 can be removed when differential input is desired, but
in that case, T1 should be changed to a 1:1 center-tap
transformer to preserve 50Ω input matching. The demo
board is shipped with optional output back-matching
resistor RMATCH = 255Ω. This results in a net output load,
ROUT = 100Ω, presented to the LT5524.
The Output Transformer Application Board (Figure 10) is
one example of an output impedance transformation
VCC
C2
0.1µF
IF
IN
T1
1:2
J1
0Ω TC2-1T
DIFFERENTIAL OUTPUT
RESISTIVE DEMO BOARD
C1
0.47µF
EN
VOSUP
1
2
3
4
5
6
7
8
9
10
PGA0 PGA1
EN
NC
VCC1
VCC2
GND
GND
LT5524
GND
GND
IN+
OUT–
IN–
OUT+
GND
GND
GND
GND
PGA0
PGA3
PGA1
PGA2
20
19
18
17
16
15
14
13
12
11
R1
50Ω
NC
ROUT
50Ω
R2
50Ω
C4
0.1µF
C5
47nF
C6
47nF
C3
4.7µF
IF
OUT
RLOAD
100Ω
J2
0PEN
PGA2 PGA3
5524 F11
Figure 11. Wideband Differential Output Application Board (Simplified Schematic)
5524f
14
LT5524
U
PACKAGE DESCRIPTIO
FE Package
20-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663)
Exposed Pad Variation CB
6.40 – 6.60*
(.252 – .260)
3.86
(.152)
3.86
(.152)
20 1918 17 16 15 14 13 12 11
6.60 ±0.10
2.74
(.108)
4.50 ±0.10
6.40
2.74 (.252)
(.108) BSC
SEE NOTE 4
0.45 ±0.05
1.05 ±0.10
0.65 BSC
1 2 3 4 5 6 7 8 9 10
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.25
REF
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
1.20
(.047)
MAX
0° – 8°
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE20 (CB) TSSOP 0204
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
5524f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT5524
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT5511
High Linearity Upconverting Mixer
RF Output to 3GHz, 17dBm IIP3, Integrated LO Buffer
LT5512
DC-3GHz High Signal Level Downconverting Mixer
DC to 3GHz, 21dBm IIP3, Integrated LO Buffer
LT5514
Ultralow Distortion IF Amplifier/ADC Driver with Digitally
Controlled Gain
47dBm OIP3 at 100MHz, 33dB Maximum Gain, 22.5dB Gain
Control Range
LT5515
1.5GHz to 2.5GHz Direct Conversion Quadrature Demodulator
20dBm IIP3, Integrated LO Quadrature Generator
LT5516
0.8GHz to 1.5GHz Direct Conversion Quadrature Demodulator
21.5dBm IIP3, Integrated LO Quadrature Generator
LT5517
40MHz to 900MHz Quadrature Demodulator
21dBm IIP3, Integrated LO Quadrature Generator
LT5519
0.7GHz to 1.4GHz High Linearity Upconverting Mixer
17.1dBm IIP3 at 1GHz, Integrated RF Output Transformer with 50Ω
Matching, Single-Ended LO and RF Ports Operation
LT5520
1.3GHz to 2.3GHz High Linearity Upconverting Mixer
15.9dBm IIP3 at 1.9GHz, Integrated RF Output Transformer with 50Ω
Matching, Single-Ended LO and RF Ports Operation
LT5521
3.7GHz Very High Linearity Upconverting Mixer
24.2dBm IIP3 at 1.9GHz, Wide 3.15V to 5.25V Supply Range,
–5dBm LO Drive, –42dBm LO-RF Leakage
LT5522
600MHz to 2.7GHz High Signal Level Downconverting Mixer
4.5V to 5.25V Supply, 25dBm IIP3 at 900MHz, NF = 12.5dB,
50Ω Single-Ended RF and LO Ports
LT5526
High Linearity, Low Power Downconverting Mixer
16.5dBm IIP3, 0.6dB Gain, 11dB NF at 900MHz,
28mA Supply Current
Infrastructure
RF Power Detectors
LT5504
800MHz to 2.7GHz RF Measuring Receiver
80dB Dynamic Range, Temperature Compensated,
2.7V to 5.25V Supply
LTC®5505
RF Power Detectors with >40dB Dynamic Range
300MHz to 3GHz, Temperature Compensated, 2.7V to 6V Supply
LTC5507
100kHz to 1000MHz RF Power Detector
100kHz to 1GHz, Temperature Compensated, 2.7V to 6V Supply
LTC5508
300MHz to 7GHz RF Power Detector
44dB Dynamic Range, Temperature Compensated, SC70 Package
LTC5509
300MHz to 3GHz RF Power Detector
36dB Dynamic Range, Low Power Consumption, SC70 Package
LTC5530
300MHz to 7GHz Precision RF Power Detector
Precision VOUT Offset Control, Shutdown, Adjustable Gain
LTC5531
300MHz to 7GHz Precision RF Power Detector
Precision VOUT Offset Control, Shutdown, Adjustable Offset
LTC5532
300MHz to 7GHz Precision RF Power Detector
Precision VOUT Offset Control, Adjustable Gain and Offset
LT5534
50MHz to 3GHz Wide Dynamic Range Log RF Power Detector
60dB Dynamic Range, Superb Temperature Stability and Accuracy,
Low Supply Current, SC70 Package
LTC5535
Precision RF Detector with 12MHz Baseband Bandwidth
600MHz to 7GHz Adjustable Gain, Precision VOUT Offset Control
Low Voltage RF Building Blocks
LT5500
1.8GHz to 2.7GHz Receiver Front End
1.8V to 5.25V Supply, Dual-Gain LNA, Mixer, LO Buffer
LT5502
400MHz Quadrature IF Demodulator with RSSI
1.8V to 5.25V Supply, 70MHz to 400MHz IF, 84dB Limiting Gain,
90dB RSSI Range
LT5503
1.2GHz to 2.7GHz Direct IQ Modulator and
Upconverting Mixer
1.8V to 5.25V Supply, Four-Step RF Power Control,
120MHz Modulation Bandwidth
LT5506
500MHz Quadrature IF Demodulator with VGA
1.8V to 5.25V Supply, 40MHz to 500MHz IF, –4dB to 57dB
Linear Power Gain, 8.8MHz Baseband Bandwidth
LT5546
500MHz Ouadrature IF Demodulator with
VGA and 17MHz Baseband Bandwidth
17MHz Baseband Bandwidth, 40MHz to 500MHz IF, 1.8V to 5.25V
Supply, –7dB to 56dB Linear Power Gain
5524f
16
Linear Technology Corporation
LT/TP 0904 1K • PRINTED IN THE USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2004