TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Total Ionizing Dose (TID) Radiation Testing of the RH1014MW Quad Precision Operational Amplifier for Linear Technology Customer: Linear Technology, PO# 58124L RAD Job Number: 10-492 Part Type Tested: RH1014MW#50197 Quad Precision Operational Amplifier. Traceability Information/Lot Number/ Date Code: Lot Date Code: 0942A, Fab Lot Number: W10737612.1, Wafer Number: 01, Assembly Lot Number: 508659.1. See photograph of unit under test in Appendix A. Quantity of Units: 12 units received, 5 units for biased irradiation, 5 units for unbiased irradiation and 2 units for control. Serial numbers 1101 and 1104-1107 were biased during irradiation, serial numbers 1108-1111 and 1113 were unbiased during irradiation and serial numbers 1124 and 1125 were used as control. Control units will be shared with RAD Job 10-493. See Appendix B for the radiation bias connection table. Radiation and Electrical Test Increments: 50-300rad(Si)/s ionizing radiation with electrical test increments: pre-irradiation, 10krad(Si), 20krad(Si), 30krad(Si) and 50krad(Si). Pre-Irradiation Burn-In: Burn-In performed by linear Technology prior to receipt by RAD. Overtest and Post-Irradiation Anneal: No overtest. 24-hour room temperature anneal followed by a 168-hour 100°C anneal. Both anneals shall be performed in the same electrical bias condition as the irradiations. Electrical measurements shall be made following each anneal increment. Radiation Test Standard: MIL-STD 883 and/or MIL-STD-750 TM1019 (latest revision), Condition A. Test Hardware and Software: LTS2020 Automated Tester, Entity ID TS03, Calibration Date: 04-28-10, Calibration Due 04-28-11. LTS2101 Family Board, Entity ID FB02. LTS0600 Test Fixture, Entity ID TF03. BGSS 970312 RH1014 DUT Board. Test Program: RH1014LT.SR2 Facility and Radiation Source: Radiation Assured Devices' Longmire Laboratories, Colorado Springs, CO. Gamma rays provided by JLSA 81-24 Co60 source. Dosimetry performed by Air Ionization Chamber (AIC) traceable to NIST. RAD's dosimetry has been audited by DSCC and RAD has been awarded Laboratory Suitability for MIL-STD-750 and MIL-STD-883 TM 1019. Irradiation and Test Temperature: Room temperature controlled to 24°C±6°C per MIL-STD-883 and MILSTD-750. High Dose Rate Test Result: PASSED the total ionizing dose characterization test to the maximum tested dose level of 50krad(Si) with all parameters remaining within their datasheet specifications. Further the units do not exhibit ELDRS as defined in the current test method. An ISO 9001:2008 and DSCC Certified Company 1 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 1.0. Overview and Background It is well known that total dose ionizing radiation can cause parametric degradation and ultimately functional failure in electronic devices. The damage occurs via electron-hole pair production, transport and trapping in the dielectric and interface regions. In discrete devices the bulk of the damage is frequently manifested as a reduction in the gain and/or breakdown voltage of the device. The damage will usually anneal with time following the end of the radiation exposure. Due to this annealing, and to ensure a worst-case test condition MIL-STD-883 TM1019.8 calls out a dose rate of 50 to 300rad(Si)/s as Condition A and further specifies that the time from the end of an incremental radiation exposure and electrical testing shall be 1-hour or less and the total time from the end of one incremental irradiation to the beginning of the next incremental radiation step should be 2-hours or less. The work described in this report was performed to meet MIL-STD-883 TM1019.8 Condition A. 2.0. Radiation Test Apparatus The total ionizing dose testing described in this final report was performed using the facilities at Radiation Assured Devices' Longmire Laboratories in Colorado Springs, CO. The high dose rate total ionizing dose (TID) source is a JLSA 81-24 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead. During the radiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from <1rad(Si)/s to a maximum of approximately 120rad(Si)/s, determined by the distance from the source. For high-dose rate experiments the bias boards are placed in a radial fashion equidistant from the raised Co-60 rods with the distance adjusted to provide the required dose rate. The irradiator calibration is maintained by Radiation Assured Devices Longmire Laboratories using air ionization chamber (AIC) equipment calibrated with traceability to the National Institute of Standards and Technology (NIST). Figure 2.1 shows a photograph of the JLSA 81-24 Co-60 irradiator at RAD's Longmire Laboratory facility. RAD is currently certified by the Defense Supply Center Columbus (DSCC) for Laboratory Suitability under MIL STD 750 and MIL-STD-883. Additional details regarding Radiation Assured Devices dosimetry for TM1019 Condition A testing are available in RAD's report to DSCC entitled: "Dose Rate Mapping of the J.L. Shepherd and Associates Model 81 Irradiator Installed by Radiation Assured Devices". An ISO 9001:2008 and DSCC Certified Company 2 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Figure 2.1. Radiation Assured Devices' high dose rate Co-60 irradiator. The dose rate is obtained by positioning the device-under-test at a fixed distance from the gamma cell. The dose rate for this irradiator varies from approximately 120rad(Si)/s close to the rods down to 1rad(Si)/s at a distance of approximately 2-feet. An ISO 9001:2008 and DSCC Certified Company 3 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 3.0. Radiation Test Conditions The RH1014MW Quad Precision Operational Amplifier described in this final report were irradiated using a split 15V supply and with all pins tied to ground, that is biased and unbiased. See the TID Bias Table in Appendix B for the full bias circuits. In our opinion, this bias circuit satisfies the requirements of MIL-STD-883H TM1019.8 Section 3.9.3 Bias and Loading Conditions which states "The bias applied to the test devices shall be selected to produce the greatest radiation induced damage or the worst-case damage for the intended application, if known. While maximum voltage is often worst case some bipolar linear device parameters (e.g. input bias current or maximum output load current) exhibit more degradation with 0 V bias." The devices were irradiated to a maximum total ionizing dose level of 50krad(Si) with incremental readings at 10krad(Si), 20krad(Si) and 30krad(Si). Electrical testing occurred within one hour following the end of each irradiation segment. For intermediate irradiations, the parts were tested and returned to total dose exposure within two hours from the end of the previous radiation increment. The TID bias board was positioned in the Co-60 cell to provide the required minimum of 50rad(Si)/s and was located inside a lead-aluminum enclosure. The lead-aluminum enclosure is required under MILSTD-883H TM1019.8 Section 3.4 that reads as follows: "Lead/Aluminum (Pb/Al) container. Test specimens shall be enclosed in a Pb/Al container to minimize dose enhancement effects caused by lowenergy, scattered radiation. A minimum of 1.5 mm Pb, surrounding an inner shield of at least 0.7 mm Al, is required. This Pb/Al container produces an approximate charged particle equilibrium for Si and for TLDs such as CaF2. The radiation field intensity shall be measured inside the Pb/Al container (1) initially, (2) when the source is changed, or (3) when the orientation or configuration of the source, container, or test-fixture is changed. This measurement shall be performed by placing a dosimeter (e.g., a TLD) in the device-irradiation container at the approximate test-device position. If it can be demonstrated that low energy scattered radiation is small enough that it will not cause dosimetry errors due to dose enhancement, the Pb/Al container may be omitted." The final dose rate within the high dose rate lead-aluminum enclosure was determined using calibration calculations based on air ionization chamber (AIC) dosimetry performed just prior to beginning the total dose irradiations. The final dose rate for this work was 52.54rad(Si)/s with a precision of ±5%. An ISO 9001:2008 and DSCC Certified Company 4 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 4.0. Tested Parameters During the total ionizing dose characterization testing the following electrical parameters were measured pre- and post-irradiation: 1. Positive Supply Current @ +/-15V (A) 2. Negative Supply Current @ +/-15V (A) 3. Offset Voltage @ +/-15V (V) 4. Offset Current @ +/-15V (A) 5. Positive Bias Current @ +/-15V (A) 6. Negative Bias Current @ +/-15V (A) 7. Common Mode Rejection Ratio (dB) 8. Power Supply Rejection Ratio (dB) 9. Open Loop Gain RL=10k VO=+/-10V (V/mV) 10. Positive Output Voltage @ +/-15V (V) 11. Negative Output Voltage @ +/-15V (V) 12. Positive Slew Rate @ +/-15V (V/us) 13. Negative Slew Rate @ +/-15V (V/us) 14. Positive Supply Current @ +5V (A) 15. Negative Supply Current @ +5V (A) 16. Offset Voltage @ +5V (V) 17. Offset Current @ +5V (A) 18. Positive Bias Current @ +5V (A) 19. Negative Bias Current @ +5V (A) 20. Positive Output Voltage RL=open @ +5V (V) 21. Positive Output Voltage RL=600 @ +5V (V) 22. Output Voltage Low RL=open @ +5V (V) 23. Output Voltage Low RL=600 @ +5V (V) 24. Output Voltage Low IL=1mA @ +5V (V) Appendix C details the measured parameters, test conditions, pre-irradiation specification and measurement resolution for each of the measurements. The parametric data was obtained as "read and record" and all the raw data plus an attributes summary are contained in this report as well as in a separate Excel file. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used in this work is 2.742 per MIL-HDBK-814 using one sided tolerance limits of 90/90 and a 5-piece sample size. The 90/90 KTL values were selected to match the statistical levels specified in the MIL-PRF-38535 sampling plan for the qualification of a radiation hardness assured (RHA) component. Note that the following criteria must be met for a device to pass the total ionizing dose test: following the radiation exposure each of the 5 pieces irradiated under electrical bias shall pass the specification value. The units irradiated without electrical bias and the KTL statistics are included in this report for reference only. If An ISO 9001:2008 and DSCC Certified Company 5 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 any of the 5 pieces irradiated under electrical bias exceed the datasheet specifications, then the lot could be logged as a failure. Further, MIL-STD-883H, TM 1019.8 Section 3.13.1.1 Characterization test to determine if a part exhibits ELDRS' states the following: Select a minimum random sample of 21 devices from a population representative of recent production runs. Smaller sample sizes may be used if agreed upon between the parties to the test. All of the selected devices shall have undergone appropriate elevated temperature reliability screens, e.g. burn-in and high temperature storage life. Divide the samples into four groups of 5 each and use the remaining part for a control. Perform pre-irradiation electrical characterization on all parts assuring that they meet the Group A electrical tests. Irradiate 5 samples under a 0 volt bias and another 5 under the irradiation bias given in the acquisition specification at 50300 rad(Si)/s and room temperature. Irradiate 5 samples under a 0 volt bias and another 5 under irradiation bias given in the acquisition specification at < 10mrad(Si)/s and room temperature. Irradiate all samples to the same dose levels, including 0.5 and 1.0 times the anticipated specification dose, and repeat the electrical characterization on each part at each dose level. Post irradiation electrical measurements shall be performed per paragraph 3.10 where the low dose rate test is considered Condition D. Calculate the radiation induced change in each electrical parameter (para) for each sample at each radiation level. Calculate the ratio of the median para at low dose rate to the median para at high dose rate for each irradiation bias group at each total dose level. If this ratio exceeds 1.5 for any of the most sensitive parameters then the part is considered to be ELDRS susceptible. This test does not apply to parameters which exhibit changes that are within experimental error or whose values are below the pre-irradiation electrical specification limits at low dose rate at the specification dose. Therefore, the data in this report can be analyzed along with the low dose rate report titled "Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1014MW Quad Precision Operational Amplifier for Linear Technology" to demonstrate that these parts do not exhibit ELDRS as defined in the current test method. 5.0. Total Ionizing Dose Test Results Based on this criterion the RH1014MW Quad Precision Operational Amplifier (from the lot date code identified on the first page of this test report) PASSED the total ionizing dose test to the maximum tested dose level of 50krad(Si) with all parameters remaining within their datasheet specifications. Figures 5.1 through 5.84 show plots of all the measured parameters versus total ionizing dose while Tables 5.1 - 5.84 show the corresponding raw data for each of these parameters. In the data plots the solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated An ISO 9001:2008 and DSCC Certified Company 6 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. In addition to the radiation test results, the data plots and tables described above contain anneal data. The anneals are performed to better understand the underlying physical mechanisms responsible for radiation-induced parametric shifts and are not part of the criteria used to establish whether or not the lot passes or fails the low dose rate test. In all cases the parts either improved or exhibited no change during the anneal. The control units, as expected, show no significant changes to any of the parameters. Therefore we can conclude that the electrical testing remained in control throughout the duration of the tests and the observed degradation was due to the radiation exposure. Appendix D lists the figures used in this section to facilitate the location of a particular parameter. An ISO 9001:2008 and DSCC Certified Company 7 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Positive Supply Current @ +/-15V (A) 2.50E-03 2.00E-03 1.50E-03 1.00E-03 5.00E-04 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 168hr 70 Anneal Figure 5.1. Plot of Positive Supply Current @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 8 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.1. Raw data for Positive Supply Current @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Supply Current @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 1.50E-03 1.53E-03 1.57E-03 1.50E-03 1.51E-03 1.49E-03 1.49E-03 1.51E-03 1.50E-03 1.49E-03 1.49E-03 1.52E-03 24hr Anneal 60 1.45E-03 1.48E-03 1.52E-03 1.45E-03 1.47E-03 1.48E-03 1.47E-03 1.49E-03 1.48E-03 1.47E-03 1.49E-03 1.52E-03 168hr Anneal 70 1.40E-03 1.43E-03 1.46E-03 1.40E-03 1.42E-03 1.46E-03 1.45E-03 1.47E-03 1.46E-03 1.46E-03 1.49E-03 1.52E-03 1.55E-03 2.99E-05 1.63E-03 1.47E-03 1.52E-03 3.04E-05 1.61E-03 1.44E-03 1.47E-03 2.84E-05 1.55E-03 1.40E-03 1.42E-03 2.72E-05 1.49E-03 1.35E-03 1.53E-03 7.92E-06 1.55E-03 1.50E-03 2.20E-03 PASS 1.50E-03 1.01E-05 1.53E-03 1.47E-03 2.20E-03 PASS 1.48E-03 9.30E-06 1.50E-03 1.45E-03 2.20E-03 PASS 1.46E-03 8.68E-06 1.49E-03 1.44E-03 2.20E-03 PASS 0 1.51E-03 1.54E-03 1.56E-03 1.50E-03 1.55E-03 1.49E-03 1.48E-03 1.50E-03 1.49E-03 1.48E-03 1.49E-03 1.51E-03 Total 10 1.51E-03 1.55E-03 1.59E-03 1.53E-03 1.53E-03 1.55E-03 1.54E-03 1.55E-03 1.55E-03 1.54E-03 1.50E-03 1.52E-03 Dose (krad(Si)) 20 30 1.53E-03 1.53E-03 1.56E-03 1.56E-03 1.60E-03 1.60E-03 1.54E-03 1.53E-03 1.55E-03 1.55E-03 1.54E-03 1.52E-03 1.53E-03 1.52E-03 1.55E-03 1.54E-03 1.54E-03 1.53E-03 1.54E-03 1.52E-03 1.50E-03 1.50E-03 1.52E-03 1.52E-03 1.53E-03 2.47E-05 1.60E-03 1.46E-03 1.54E-03 2.91E-05 1.62E-03 1.46E-03 1.56E-03 2.76E-05 1.63E-03 1.48E-03 1.49E-03 8.60E-06 1.51E-03 1.46E-03 2.20E-03 PASS 1.55E-03 7.02E-06 1.56E-03 1.53E-03 2.20E-03 PASS 1.54E-03 7.66E-06 1.56E-03 1.52E-03 2.20E-03 PASS An ISO 9001:2008 and DSCC Certified Company 9 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Negative Supply Current @ +/-15V (A) 0.00E+00 -5.00E-04 -1.00E-03 -1.50E-03 -2.00E-03 -2.50E-03 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.2. Plot of Negative Supply Current @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 10 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.2. Raw data for Negative Supply Current @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Supply Current @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 -1.50E-03 -1.53E-03 -1.57E-03 -1.50E-03 -1.51E-03 -1.50E-03 -1.49E-03 -1.52E-03 -1.50E-03 -1.49E-03 -1.50E-03 -1.51E-03 24hr Anneal 60 -1.45E-03 -1.48E-03 -1.52E-03 -1.45E-03 -1.47E-03 -1.47E-03 -1.47E-03 -1.49E-03 -1.48E-03 -1.47E-03 -1.49E-03 -1.52E-03 168hr Anneal 70 -1.40E-03 -1.43E-03 -1.46E-03 -1.40E-03 -1.42E-03 -1.46E-03 -1.45E-03 -1.48E-03 -1.47E-03 -1.46E-03 -1.50E-03 -1.52E-03 -1.55E-03 3.07E-05 -1.47E-03 -1.64E-03 -1.52E-03 2.98E-05 -1.44E-03 -1.60E-03 -1.47E-03 2.91E-05 -1.39E-03 -1.55E-03 -1.42E-03 2.68E-05 -1.35E-03 -1.50E-03 -1.53E-03 8.35E-06 -1.50E-03 -1.55E-03 -2.20E-03 PASS -1.50E-03 1.03E-05 -1.47E-03 -1.53E-03 -2.20E-03 PASS -1.48E-03 9.20E-06 -1.45E-03 -1.50E-03 -2.20E-03 PASS -1.46E-03 8.60E-06 -1.44E-03 -1.49E-03 -2.20E-03 PASS 0 -1.51E-03 -1.54E-03 -1.56E-03 -1.50E-03 -1.55E-03 -1.49E-03 -1.48E-03 -1.50E-03 -1.49E-03 -1.48E-03 -1.49E-03 -1.51E-03 Total 10 -1.51E-03 -1.55E-03 -1.59E-03 -1.53E-03 -1.53E-03 -1.55E-03 -1.54E-03 -1.56E-03 -1.55E-03 -1.54E-03 -1.50E-03 -1.52E-03 Dose (krad(Si)) 20 30 -1.54E-03 -1.53E-03 -1.56E-03 -1.56E-03 -1.61E-03 -1.60E-03 -1.54E-03 -1.53E-03 -1.55E-03 -1.55E-03 -1.54E-03 -1.52E-03 -1.53E-03 -1.52E-03 -1.55E-03 -1.54E-03 -1.54E-03 -1.53E-03 -1.54E-03 -1.52E-03 -1.50E-03 -1.50E-03 -1.52E-03 -1.52E-03 -1.53E-03 2.48E-05 -1.46E-03 -1.60E-03 -1.54E-03 2.91E-05 -1.46E-03 -1.62E-03 -1.56E-03 2.78E-05 -1.48E-03 -1.64E-03 -1.49E-03 8.91E-06 -1.46E-03 -1.51E-03 -2.20E-03 PASS -1.55E-03 8.17E-06 -1.52E-03 -1.57E-03 -2.20E-03 PASS -1.54E-03 8.17E-06 -1.52E-03 -1.56E-03 -2.20E-03 PASS An ISO 9001:2008 and DSCC Certified Company 11 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 8.00E-04 Offset Voltage 1 @ +/-15V (V) 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.3. Plot of Offset Voltage 1 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 12 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.3. Raw data for Offset Voltage 1 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Voltage 1 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 8.86E-05 5.47E-05 7.07E-05 5.50E-05 1.46E-05 1.22E-04 -4.23E-06 1.69E-06 1.30E-04 1.17E-05 -6.10E-05 -1.07E-05 24hr Anneal 60 9.03E-05 5.52E-05 7.12E-05 6.22E-05 1.64E-05 1.14E-04 -7.85E-06 -3.99E-06 1.21E-04 8.08E-06 -6.13E-05 -1.10E-05 168hr Anneal 70 7.09E-05 4.45E-05 6.19E-05 6.41E-05 6.00E-07 8.98E-05 -1.63E-05 -3.22E-05 9.81E-05 -3.50E-06 -6.30E-05 -1.12E-05 3.58E-05 2.96E-05 1.17E-04 -4.52E-05 5.67E-05 2.74E-05 1.32E-04 -1.83E-05 5.90E-05 2.72E-05 1.34E-04 -1.56E-05 4.84E-05 2.84E-05 1.26E-04 -2.96E-05 3.37E-05 6.31E-05 2.07E-04 -1.39E-04 -5.00E-04 PASS 5.00E-04 PASS 5.22E-05 6.76E-05 2.37E-04 -1.33E-04 -6.00E-04 PASS 6.00E-04 PASS 4.64E-05 6.56E-05 2.26E-04 -1.33E-04 -6.00E-04 PASS 6.00E-04 PASS 2.72E-05 6.19E-05 1.97E-04 -1.43E-04 -6.00E-04 PASS 6.00E-04 PASS 0 5.34E-05 2.14E-05 5.92E-05 4.26E-05 -1.36E-05 6.97E-05 -3.50E-05 -4.97E-05 6.99E-05 -1.82E-05 -6.28E-05 -1.10E-05 Total 10 3.61E-05 2.40E-05 3.27E-05 1.92E-05 -3.71E-05 7.70E-05 -3.14E-05 -4.27E-05 7.95E-05 -1.80E-05 -6.20E-05 -1.04E-05 Dose (krad(Si)) 20 30 4.67E-05 6.22E-05 2.70E-05 3.85E-05 4.31E-05 5.47E-05 2.78E-05 3.73E-05 -2.72E-05 -1.35E-05 8.56E-05 1.02E-04 -2.13E-05 -1.81E-05 -3.22E-05 -1.94E-05 9.16E-05 1.03E-04 -6.52E-06 1.69E-06 -6.24E-05 -6.13E-05 -1.12E-05 -1.12E-05 3.26E-05 2.96E-05 1.14E-04 -4.85E-05 1.50E-05 2.99E-05 9.69E-05 -6.69E-05 2.35E-05 2.97E-05 1.05E-04 -5.78E-05 7.31E-06 5.81E-05 1.67E-04 -1.52E-04 -3.00E-04 PASS 3.00E-04 PASS 1.29E-05 6.03E-05 1.78E-04 -1.53E-04 -4.50E-04 PASS 4.50E-04 PASS 2.34E-05 6.02E-05 1.89E-04 -1.42E-04 -4.50E-04 PASS 4.50E-04 PASS An ISO 9001:2008 and DSCC Certified Company 13 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 8.00E-04 Offset Voltage 2 @ +/-15V (V) 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.4. Plot of Offset Voltage 2 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 14 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.4. Raw data for Offset Voltage 2 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Voltage 2 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 1.29E-04 4.25E-05 1.09E-04 8.33E-05 7.72E-05 1.12E-04 2.12E-05 5.49E-05 5.07E-05 3.78E-05 1.32E-05 -9.30E-06 24hr Anneal 60 1.28E-04 4.90E-05 1.05E-04 7.98E-05 7.35E-05 1.06E-04 1.87E-05 5.15E-05 5.31E-05 3.19E-05 1.33E-05 -8.94E-06 168hr Anneal 70 1.03E-04 3.60E-05 9.28E-05 5.77E-05 6.02E-05 6.70E-05 -1.20E-05 2.27E-05 3.32E-05 7.20E-07 1.40E-05 -9.18E-06 6.93E-05 2.84E-05 1.47E-04 -8.71E-06 8.83E-05 3.29E-05 1.79E-04 -2.00E-06 8.71E-05 3.04E-05 1.70E-04 3.81E-06 7.00E-05 2.76E-05 1.46E-04 -5.62E-06 4.02E-05 3.09E-05 1.25E-04 -4.45E-05 -5.00E-04 PASS 5.00E-04 PASS 5.54E-05 3.43E-05 1.50E-04 -3.88E-05 -6.00E-04 PASS 6.00E-04 PASS 5.23E-05 3.35E-05 1.44E-04 -3.94E-05 -6.00E-04 PASS 6.00E-04 PASS 2.23E-05 3.06E-05 1.06E-04 -6.17E-05 -6.00E-04 PASS 6.00E-04 PASS 0 7.91E-05 3.19E-05 6.83E-05 3.98E-05 4.97E-05 5.19E-05 -1.55E-05 2.00E-05 3.17E-05 -4.23E-06 1.22E-05 -1.06E-05 Total 10 8.34E-05 2.80E-05 7.68E-05 4.53E-05 3.37E-05 6.10E-05 -8.09E-06 2.45E-05 3.31E-05 7.00E-06 1.53E-05 -9.06E-06 Dose (krad(Si)) 20 30 9.14E-05 1.02E-04 3.09E-05 3.28E-05 8.53E-05 9.41E-05 5.20E-05 5.97E-05 4.51E-05 5.77E-05 7.51E-05 8.93E-05 -3.75E-06 7.24E-06 3.26E-05 3.71E-05 3.81E-05 4.45E-05 1.51E-05 2.31E-05 1.40E-05 1.36E-05 -9.30E-06 -9.66E-06 5.38E-05 1.96E-05 1.08E-04 -7.65E-08 5.34E-05 2.52E-05 1.23E-04 -1.58E-05 6.09E-05 2.62E-05 1.33E-04 -1.10E-05 1.68E-05 2.72E-05 9.12E-05 -5.77E-05 -3.00E-04 PASS 3.00E-04 PASS 2.35E-05 2.63E-05 9.56E-05 -4.86E-05 -4.50E-04 PASS 4.50E-04 PASS 3.14E-05 2.94E-05 1.12E-04 -4.92E-05 -4.50E-04 PASS 4.50E-04 PASS An ISO 9001:2008 and DSCC Certified Company 15 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 8.00E-04 Offset Voltage 3 @ +/-15V (V) 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.5. Plot of Offset Voltage 3 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 16 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.5. Raw data for Offset Voltage 3 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Voltage 3 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 6.04E-05 -3.31E-05 4.91E-05 3.37E-05 3.79E-05 1.03E-04 2.95E-05 9.33E-05 5.94E-05 3.77E-05 -5.79E-05 -6.04E-06 24hr Anneal 60 6.34E-05 -2.21E-05 5.11E-05 3.68E-05 3.45E-05 9.35E-05 2.58E-05 8.99E-05 6.08E-05 2.75E-05 -5.79E-05 -5.19E-06 168hr Anneal 70 5.87E-05 -1.47E-05 4.54E-05 5.12E-05 2.67E-05 6.20E-05 6.15E-06 6.36E-05 4.25E-05 2.89E-06 -5.82E-05 -4.11E-06 1.08E-05 3.07E-05 9.50E-05 -7.34E-05 2.96E-05 3.65E-05 1.30E-04 -7.06E-05 3.27E-05 3.28E-05 1.23E-04 -5.72E-05 3.34E-05 2.94E-05 1.14E-04 -4.72E-05 4.72E-05 3.08E-05 1.32E-04 -3.72E-05 -5.00E-04 PASS 5.00E-04 PASS 6.46E-05 3.28E-05 1.54E-04 -2.53E-05 -6.00E-04 PASS 6.00E-04 PASS 5.95E-05 3.26E-05 1.49E-04 -2.98E-05 -6.00E-04 PASS 6.00E-04 PASS 3.54E-05 2.94E-05 1.16E-04 -4.53E-05 -6.00E-04 PASS 6.00E-04 PASS 0 2.68E-05 -3.53E-05 2.10E-05 1.91E-05 -8.70E-06 4.33E-05 -1.32E-05 5.17E-05 2.40E-05 -6.64E-06 -5.82E-05 -5.56E-06 Total 10 1.63E-05 -4.72E-05 7.00E-06 7.20E-07 -2.26E-05 4.97E-05 -1.16E-05 6.07E-05 3.07E-05 1.32E-06 -5.83E-05 -4.71E-06 Dose (krad(Si)) 20 30 2.68E-05 3.80E-05 -4.61E-05 -4.09E-05 1.70E-05 2.76E-05 1.26E-05 1.93E-05 -6.88E-06 1.00E-05 6.20E-05 7.79E-05 2.40E-07 1.16E-05 6.82E-05 7.75E-05 3.68E-05 4.74E-05 9.77E-06 2.15E-05 -5.73E-05 -5.83E-05 -5.80E-06 -6.64E-06 4.58E-06 2.62E-05 7.63E-05 -6.71E-05 -9.15E-06 2.57E-05 6.12E-05 -7.95E-05 6.72E-07 2.89E-05 7.99E-05 -7.85E-05 1.98E-05 2.90E-05 9.95E-05 -5.98E-05 -3.00E-04 PASS 3.00E-04 PASS 2.62E-05 3.09E-05 1.11E-04 -5.85E-05 -4.50E-04 PASS 4.50E-04 PASS 3.54E-05 3.03E-05 1.19E-04 -4.78E-05 -4.50E-04 PASS 4.50E-04 PASS An ISO 9001:2008 and DSCC Certified Company 17 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 8.00E-04 Offset Voltage 4 @ +/-15V (V) 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.6. Plot of Offset Voltage 4 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 18 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.6. Raw data for Offset Voltage 4 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Voltage 4 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 5.03E-05 9.39E-05 -2.18E-06 1.38E-04 5.75E-05 3.13E-05 9.43E-05 9.32E-05 1.36E-05 7.11E-05 -2.61E-05 3.01E-05 24hr Anneal 60 4.70E-05 9.04E-05 -9.18E-06 1.32E-04 5.37E-05 3.15E-05 8.86E-05 8.20E-05 3.74E-06 7.23E-05 -2.52E-05 2.88E-05 168hr Anneal 70 4.26E-05 7.74E-05 -2.08E-05 1.24E-04 3.49E-05 4.34E-06 7.83E-05 5.43E-05 -2.89E-05 4.76E-05 -2.60E-05 2.76E-05 4.87E-05 5.00E-05 1.86E-04 -8.84E-05 6.75E-05 5.22E-05 2.11E-04 -7.57E-05 6.28E-05 5.27E-05 2.07E-04 -8.16E-05 5.17E-05 5.37E-05 1.99E-04 -9.56E-05 4.16E-05 3.44E-05 1.36E-04 -5.28E-05 -5.00E-04 PASS 5.00E-04 PASS 6.07E-05 3.66E-05 1.61E-04 -3.98E-05 -6.00E-04 PASS 6.00E-04 PASS 5.56E-05 3.65E-05 1.56E-04 -4.45E-05 -6.00E-04 PASS 6.00E-04 PASS 3.11E-05 4.29E-05 1.49E-04 -8.64E-05 -6.00E-04 PASS 6.00E-04 PASS 0 -1.20E-07 4.90E-05 -3.20E-05 9.54E-05 6.51E-06 -1.63E-05 2.04E-05 2.52E-05 -3.76E-05 6.17E-05 -2.66E-05 2.80E-05 Total 10 6.88E-06 6.01E-05 -2.74E-05 1.00E-04 1.47E-05 -1.03E-05 4.33E-05 4.19E-05 -2.72E-05 5.02E-05 -2.60E-05 2.86E-05 Dose (krad(Si)) 20 30 1.62E-05 2.69E-05 6.72E-05 7.75E-05 -2.15E-05 -1.36E-05 1.07E-04 1.17E-04 2.22E-05 3.60E-05 3.01E-06 1.58E-05 5.68E-05 7.00E-05 5.71E-05 6.76E-05 -1.84E-05 -5.80E-06 5.60E-05 6.02E-05 -2.56E-05 -2.80E-05 2.86E-05 2.91E-05 2.38E-05 4.93E-05 1.59E-04 -1.12E-04 3.09E-05 4.97E-05 1.67E-04 -1.05E-04 3.83E-05 4.98E-05 1.75E-04 -9.82E-05 1.07E-05 3.86E-05 1.17E-04 -9.52E-05 -3.00E-04 PASS 3.00E-04 PASS 1.96E-05 3.56E-05 1.17E-04 -7.81E-05 -4.50E-04 PASS 4.50E-04 PASS 3.09E-05 3.60E-05 1.30E-04 -6.79E-05 -4.50E-04 PASS 4.50E-04 PASS An ISO 9001:2008 and DSCC Certified Company 19 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.00E-08 Offset Current 1 @ +/-15V (A) 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.7. Plot of Offset Current 1 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 20 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.7. Raw data for Offset Current 1 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Current 1 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 1.53E-10 1.73E-10 5.08E-10 7.90E-11 -1.80E-11 4.10E-11 1.08E-10 1.75E-10 4.20E-11 -8.70E-11 -4.60E-11 4.60E-11 24hr Anneal 60 1.96E-10 3.44E-10 6.42E-10 5.20E-11 1.20E-11 -1.00E-12 1.43E-10 1.06E-10 3.00E-12 -7.80E-11 -6.50E-11 5.10E-11 168hr Anneal 70 2.29E-10 5.30E-11 4.05E-10 3.00E-12 4.10E-11 3.30E-11 -2.90E-11 6.10E-11 -8.00E-11 4.50E-11 -5.90E-11 3.50E-11 9.04E-11 1.04E-10 3.74E-10 -1.94E-10 1.79E-10 1.99E-10 7.24E-10 -3.66E-10 2.49E-10 2.56E-10 9.50E-10 -4.52E-10 1.46E-10 1.69E-10 6.09E-10 -3.17E-10 -1.84E-11 4.45E-11 1.04E-10 -1.41E-10 -1.17E-08 PASS 1.17E-08 PASS 5.58E-11 9.71E-11 3.22E-10 -2.11E-10 -1.50E-08 PASS 1.50E-08 PASS 3.46E-11 8.92E-11 2.79E-10 -2.10E-10 -1.50E-08 PASS 1.50E-08 PASS 6.00E-12 5.89E-11 1.68E-10 -1.56E-10 -1.50E-08 PASS 1.50E-08 PASS 0 -1.70E-11 1.06E-10 -5.40E-11 -9.00E-11 -1.01E-10 -1.07E-10 -4.70E-11 -9.10E-11 -1.26E-10 4.20E-11 -6.80E-11 4.10E-11 Total 10 3.50E-11 1.33E-10 -1.10E-11 -6.00E-11 -8.90E-11 -4.60E-11 -4.40E-11 -4.30E-11 -1.43E-10 2.30E-11 -6.40E-11 2.10E-11 Dose (krad(Si)) 20 30 5.60E-11 1.21E-10 1.59E-10 1.58E-10 1.67E-10 1.93E-10 -3.30E-11 4.80E-11 -5.70E-11 -6.80E-11 -2.20E-11 -5.70E-11 -2.50E-11 4.70E-11 -5.00E-11 -2.00E-12 -4.10E-11 -1.80E-11 -2.10E-11 -6.20E-11 -7.40E-11 -5.90E-11 4.70E-11 6.20E-11 -3.12E-11 8.35E-11 1.98E-10 -2.60E-10 1.60E-12 8.74E-11 2.41E-10 -2.38E-10 5.84E-11 1.04E-10 3.45E-10 -2.28E-10 -6.58E-11 6.70E-11 1.18E-10 -2.49E-10 -1.00E-08 PASS 1.00E-08 PASS -5.06E-11 5.93E-11 1.12E-10 -2.13E-10 -1.00E-08 PASS 1.00E-08 PASS -3.18E-11 1.30E-11 3.81E-12 -6.74E-11 -1.00E-08 PASS 1.00E-08 PASS An ISO 9001:2008 and DSCC Certified Company 21 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.00E-08 Offset Current 2 @ +/-15V (A) 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.8. Plot of Offset Current 2 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 22 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.8. Raw data for Offset Current 2 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Current 2 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 -7.50E-11 9.30E-11 2.33E-10 3.11E-10 3.31E-10 1.83E-10 1.85E-10 1.73E-10 4.20E-11 8.70E-11 -6.00E-12 8.50E-11 24hr Anneal 60 7.50E-11 1.57E-10 1.96E-10 3.17E-10 3.20E-10 -1.50E-11 1.15E-10 -4.00E-12 8.20E-11 1.49E-10 -3.10E-11 8.20E-11 168hr Anneal 70 1.80E-10 -3.50E-11 5.30E-11 2.94E-10 2.24E-10 2.00E-11 7.20E-11 1.26E-10 1.08E-10 1.35E-10 -3.40E-11 7.90E-11 9.58E-11 1.49E-10 5.05E-10 -3.13E-10 1.79E-10 1.70E-10 6.44E-10 -2.87E-10 2.13E-10 1.06E-10 5.03E-10 -7.70E-11 1.43E-10 1.33E-10 5.07E-10 -2.21E-10 8.00E-13 7.14E-11 1.97E-10 -1.95E-10 -1.17E-08 PASS 1.17E-08 PASS 1.34E-10 6.56E-11 3.14E-10 -4.58E-11 -1.50E-08 PASS 1.50E-08 PASS 6.54E-11 7.25E-11 2.64E-10 -1.33E-10 -1.50E-08 PASS 1.50E-08 PASS 9.22E-11 4.70E-11 2.21E-10 -3.67E-11 -1.50E-08 PASS 1.50E-08 PASS 0 -1.14E-10 4.90E-11 -1.22E-10 -2.60E-11 3.40E-11 -3.20E-11 -9.40E-11 -7.40E-11 3.70E-11 -1.80E-11 -7.00E-12 6.60E-11 Total 10 -8.60E-11 9.80E-11 -9.50E-11 1.10E-11 2.20E-11 3.50E-11 -8.20E-11 -8.70E-11 7.00E-11 1.80E-11 -4.50E-11 9.50E-11 Dose (krad(Si)) 20 30 -1.19E-10 -1.15E-10 0.00E+00 4.50E-11 -6.10E-11 8.60E-11 1.56E-10 2.82E-10 6.50E-11 1.81E-10 2.80E-11 3.50E-11 -5.90E-11 -1.23E-10 -6.80E-11 2.00E-12 8.80E-11 4.50E-11 -2.50E-11 4.50E-11 -1.30E-11 -3.10E-11 9.70E-11 7.10E-11 -3.58E-11 8.02E-11 1.84E-10 -2.56E-10 -1.00E-11 8.08E-11 2.12E-10 -2.32E-10 8.20E-12 1.07E-10 3.03E-10 -2.86E-10 -3.62E-11 5.12E-11 1.04E-10 -1.77E-10 -1.00E-08 PASS 1.00E-08 PASS -9.20E-12 7.13E-11 1.86E-10 -2.05E-10 -1.00E-08 PASS 1.00E-08 PASS -7.20E-12 6.52E-11 1.72E-10 -1.86E-10 -1.00E-08 PASS 1.00E-08 PASS An ISO 9001:2008 and DSCC Certified Company 23 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.00E-08 Offset Current 3 @ +/-15V (A) 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.9. Plot of Offset Current 3 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 24 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.9. Raw data for Offset Current 3 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Current 3 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 2.90E-10 1.76E-10 2.19E-10 2.47E-10 -2.60E-11 1.21E-10 -7.80E-11 1.67E-10 1.90E-11 2.79E-10 6.00E-12 5.50E-11 24hr Anneal 60 1.77E-10 1.00E-10 1.92E-10 1.26E-10 -2.10E-11 1.76E-10 -1.50E-11 1.12E-10 -5.00E-12 3.23E-10 2.10E-11 5.20E-11 168hr Anneal 70 1.04E-10 2.00E-10 3.09E-10 1.50E-10 1.89E-10 1.39E-10 -9.20E-11 7.30E-11 9.00E-11 5.70E-11 1.70E-11 7.50E-11 5.60E-11 1.08E-10 3.51E-10 -2.39E-10 1.81E-10 1.23E-10 5.19E-10 -1.56E-10 1.15E-10 8.46E-11 3.47E-10 -1.17E-10 1.90E-10 7.63E-11 3.99E-10 -1.87E-11 2.82E-11 9.21E-11 2.81E-10 -2.24E-10 -1.17E-08 PASS 1.17E-08 PASS 1.02E-10 1.37E-10 4.78E-10 -2.74E-10 -1.50E-08 PASS 1.50E-08 PASS 1.18E-10 1.40E-10 5.02E-10 -2.65E-10 -1.50E-08 PASS 1.50E-08 PASS 5.34E-11 8.69E-11 2.92E-10 -1.85E-10 -1.50E-08 PASS 1.50E-08 PASS 0 -3.30E-11 2.30E-11 -8.80E-11 -8.80E-11 -1.39E-10 -1.70E-11 5.00E-12 -3.30E-11 -2.10E-11 1.70E-11 3.90E-11 7.20E-11 Total 10 -2.50E-11 5.60E-11 -3.80E-11 -7.30E-11 -1.08E-10 6.40E-11 -5.60E-11 4.00E-12 -3.70E-11 1.08E-10 1.50E-11 4.40E-11 Dose (krad(Si)) 20 30 5.80E-11 5.20E-11 1.04E-10 1.42E-10 3.70E-11 1.53E-10 -3.30E-11 4.90E-11 -1.08E-10 -1.16E-10 4.30E-11 3.70E-11 -5.00E-11 -1.14E-10 4.20E-11 6.80E-11 2.00E-12 1.30E-11 1.40E-10 1.37E-10 5.00E-12 3.80E-11 4.00E-11 7.50E-11 -6.50E-11 6.19E-11 1.05E-10 -2.35E-10 -3.76E-11 6.15E-11 1.31E-10 -2.06E-10 1.16E-11 8.31E-11 2.39E-10 -2.16E-10 -9.80E-12 2.03E-11 4.59E-11 -6.55E-11 -1.00E-08 PASS 1.00E-08 PASS 1.66E-11 6.87E-11 2.05E-10 -1.72E-10 -1.00E-08 PASS 1.00E-08 PASS 3.54E-11 6.97E-11 2.27E-10 -1.56E-10 -1.00E-08 PASS 1.00E-08 PASS An ISO 9001:2008 and DSCC Certified Company 25 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.00E-08 Offset Current 4 @ +/-15V (A) 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.10. Plot of Offset Current 4 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 26 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.10. Raw data for Offset Current 4 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Current 4 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 1.85E-10 6.90E-11 4.36E-10 -1.20E-11 2.50E-10 -3.00E-11 2.26E-10 1.32E-10 2.32E-10 5.00E-12 5.90E-11 9.00E-12 24hr Anneal 60 2.43E-10 1.04E-10 4.17E-10 1.09E-10 2.35E-10 -1.35E-10 1.59E-10 1.82E-10 1.49E-10 -4.00E-11 6.40E-11 0.00E+00 168hr Anneal 70 1.50E-10 1.41E-10 4.34E-10 1.60E-11 1.41E-10 9.00E-12 9.20E-11 1.75E-10 -7.50E-11 4.00E-12 6.10E-11 2.00E-12 1.53E-10 9.71E-11 4.19E-10 -1.14E-10 1.86E-10 1.73E-10 6.60E-10 -2.88E-10 2.22E-10 1.28E-10 5.72E-10 -1.29E-10 1.76E-10 1.54E-10 6.00E-10 -2.47E-10 6.88E-11 8.49E-11 3.02E-10 -1.64E-10 -1.17E-08 PASS 1.17E-08 PASS 1.13E-10 1.22E-10 4.47E-10 -2.21E-10 -1.50E-08 PASS 1.50E-08 PASS 6.30E-11 1.42E-10 4.52E-10 -3.26E-10 -1.50E-08 PASS 1.50E-08 PASS 4.10E-11 9.54E-11 3.03E-10 -2.21E-10 -1.50E-08 PASS 1.50E-08 PASS 0 -8.00E-12 7.00E-12 5.90E-11 -5.80E-11 -5.10E-11 -1.48E-10 2.60E-11 7.90E-11 -5.50E-11 -7.00E-12 6.70E-11 2.90E-11 Total 10 6.20E-11 6.80E-11 3.70E-11 -5.40E-11 3.30E-11 -1.52E-10 1.90E-11 1.30E-10 -1.10E-11 0.00E+00 7.40E-11 2.90E-11 Dose (krad(Si)) 20 30 9.50E-11 9.30E-11 9.30E-11 8.10E-11 1.20E-10 2.87E-10 1.00E-11 7.70E-11 1.36E-10 2.25E-10 -1.19E-10 -5.20E-11 8.10E-11 7.20E-11 1.32E-10 1.53E-10 2.70E-11 1.43E-10 5.80E-11 2.80E-11 5.80E-11 7.10E-11 2.50E-11 5.80E-11 -1.02E-11 4.75E-11 1.20E-10 -1.41E-10 2.92E-11 4.89E-11 1.63E-10 -1.05E-10 9.08E-11 4.86E-11 2.24E-10 -4.25E-11 -2.10E-11 8.62E-11 2.15E-10 -2.57E-10 -1.00E-08 PASS 1.00E-08 PASS -2.80E-12 1.01E-10 2.73E-10 -2.79E-10 -1.00E-08 PASS 1.00E-08 PASS 3.58E-11 9.46E-11 2.95E-10 -2.24E-10 -1.00E-08 PASS 1.00E-08 PASS An ISO 9001:2008 and DSCC Certified Company 27 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Bias Current 1 @ +/-15V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.11. Plot of Positive Bias Current 1 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 28 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.11. Raw data for Positive Bias Current 1 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Bias Current 1 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.35E-08 1.57E-08 1.37E-08 1.58E-08 1.44E-08 1.67E-08 1.46E-08 1.70E-08 1.33E-08 1.55E-08 1.33E-08 1.52E-08 1.40E-08 1.59E-08 1.39E-08 1.58E-08 1.44E-08 1.63E-08 1.29E-08 1.47E-08 9.97E-09 9.93E-09 1.00E-08 1.00E-08 50 2.02E-08 2.02E-08 2.15E-08 2.17E-08 1.99E-08 1.83E-08 1.91E-08 1.91E-08 1.94E-08 1.77E-08 9.92E-09 1.01E-08 24hr Anneal 60 2.24E-08 2.23E-08 2.37E-08 2.39E-08 2.18E-08 1.85E-08 1.92E-08 1.92E-08 1.97E-08 1.78E-08 9.93E-09 1.00E-08 168hr Anneal 70 2.20E-08 2.21E-08 2.35E-08 2.37E-08 2.17E-08 1.71E-08 1.80E-08 1.79E-08 1.86E-08 1.66E-08 9.93E-09 1.00E-08 0 1.04E-08 1.06E-08 1.10E-08 1.11E-08 1.03E-08 1.04E-08 1.10E-08 1.09E-08 1.14E-08 1.00E-08 9.94E-09 1.00E-08 Total 10 1.17E-08 1.19E-08 1.24E-08 1.25E-08 1.14E-08 1.17E-08 1.24E-08 1.21E-08 1.27E-08 1.13E-08 9.97E-09 1.01E-08 1.07E-08 3.72E-10 1.17E-08 9.66E-09 1.20E-08 4.60E-10 1.32E-08 1.07E-08 1.39E-08 5.67E-10 1.54E-08 1.23E-08 1.61E-08 6.67E-10 1.80E-08 1.43E-08 2.07E-08 8.54E-10 2.30E-08 1.83E-08 2.28E-08 9.31E-10 2.54E-08 2.03E-08 2.26E-08 9.40E-10 2.52E-08 2.00E-08 1.07E-08 5.30E-10 1.22E-08 9.29E-09 -3.00E-08 PASS 3.00E-08 PASS 1.20E-08 5.60E-10 1.36E-08 1.05E-08 -6.00E-08 PASS 6.00E-08 PASS 1.37E-08 5.93E-10 1.53E-08 1.21E-08 -7.50E-08 PASS 7.50E-08 PASS 1.56E-08 6.07E-10 1.72E-08 1.39E-08 -8.33E-08 PASS 8.33E-08 PASS 1.87E-08 7.25E-10 2.07E-08 1.67E-08 -1.00E-07 PASS 1.00E-07 PASS 1.89E-08 7.75E-10 2.10E-08 1.67E-08 -1.00E-07 PASS 1.00E-07 PASS 1.76E-08 7.92E-10 1.98E-08 1.55E-08 -1.00E-07 PASS 1.00E-07 PASS An ISO 9001:2008 and DSCC Certified Company 29 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Bias Current 2 @ +/-15V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.12. Plot of Positive Bias Current 2 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 30 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.12. Raw data for Positive Bias Current 2 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Bias Current 2 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.46E-08 1.70E-08 1.34E-08 1.56E-08 1.46E-08 1.68E-08 1.47E-08 1.70E-08 1.36E-08 1.58E-08 1.47E-08 1.67E-08 1.43E-08 1.63E-08 1.43E-08 1.62E-08 1.26E-08 1.45E-08 1.32E-08 1.52E-08 1.06E-08 1.07E-08 9.80E-09 9.78E-09 50 2.16E-08 2.02E-08 2.15E-08 2.19E-08 2.03E-08 2.02E-08 1.95E-08 1.96E-08 1.76E-08 1.84E-08 1.07E-08 9.76E-09 24hr Anneal 60 2.40E-08 2.22E-08 2.38E-08 2.40E-08 2.24E-08 2.05E-08 1.97E-08 1.98E-08 1.76E-08 1.85E-08 1.07E-08 9.81E-09 168hr Anneal 70 2.37E-08 2.15E-08 2.34E-08 2.38E-08 2.23E-08 1.89E-08 1.82E-08 1.82E-08 1.61E-08 1.72E-08 1.06E-08 9.77E-09 0 1.15E-08 1.01E-08 1.11E-08 1.12E-08 1.05E-08 1.14E-08 1.11E-08 1.12E-08 9.61E-09 1.04E-08 1.06E-08 9.75E-09 Total 10 1.26E-08 1.15E-08 1.25E-08 1.26E-08 1.18E-08 1.29E-08 1.25E-08 1.25E-08 1.09E-08 1.16E-08 1.07E-08 9.76E-09 1.09E-08 5.51E-10 1.24E-08 9.35E-09 1.22E-08 5.21E-10 1.37E-08 1.08E-08 1.42E-08 6.31E-10 1.59E-08 1.24E-08 1.64E-08 6.77E-10 1.83E-08 1.46E-08 2.11E-08 8.10E-10 2.33E-08 1.89E-08 2.33E-08 9.03E-10 2.58E-08 2.08E-08 2.29E-08 1.01E-09 2.57E-08 2.02E-08 1.07E-08 7.48E-10 1.28E-08 8.69E-09 -3.00E-08 PASS 3.00E-08 PASS 1.21E-08 8.03E-10 1.43E-08 9.89E-09 -6.00E-08 PASS 6.00E-08 PASS 1.38E-08 8.78E-10 1.62E-08 1.14E-08 -7.50E-08 PASS 7.50E-08 PASS 1.58E-08 9.18E-10 1.83E-08 1.33E-08 -8.33E-08 PASS 8.33E-08 PASS 1.91E-08 1.05E-09 2.20E-08 1.62E-08 -1.00E-07 PASS 1.00E-07 PASS 1.92E-08 1.15E-09 2.24E-08 1.60E-08 -1.00E-07 PASS 1.00E-07 PASS 1.77E-08 1.11E-09 2.08E-08 1.47E-08 -1.00E-07 PASS 1.00E-07 PASS An ISO 9001:2008 and DSCC Certified Company 31 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Bias Current 3 @ +/-15V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.13. Plot of Positive Bias Current 3 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 32 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.13. Raw data for Positive Bias Current 3 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Bias Current 3 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.34E-08 1.57E-08 1.36E-08 1.58E-08 1.39E-08 1.60E-08 1.41E-08 1.64E-08 1.39E-08 1.62E-08 1.42E-08 1.63E-08 1.36E-08 1.56E-08 1.38E-08 1.56E-08 1.29E-08 1.48E-08 1.29E-08 1.47E-08 1.01E-08 1.01E-08 9.40E-09 9.36E-09 50 2.00E-08 2.04E-08 2.05E-08 2.10E-08 2.06E-08 1.97E-08 1.88E-08 1.90E-08 1.80E-08 1.78E-08 1.01E-08 9.37E-09 24hr Anneal 60 2.23E-08 2.26E-08 2.28E-08 2.31E-08 2.29E-08 1.99E-08 1.89E-08 1.90E-08 1.80E-08 1.79E-08 1.01E-08 9.38E-09 168hr Anneal 70 2.19E-08 2.18E-08 2.23E-08 2.27E-08 2.26E-08 1.83E-08 1.76E-08 1.76E-08 1.65E-08 1.68E-08 1.01E-08 9.37E-09 0 1.04E-08 1.03E-08 1.06E-08 1.07E-08 1.08E-08 1.10E-08 1.05E-08 1.08E-08 9.88E-09 1.01E-08 1.01E-08 9.38E-09 Total 10 1.17E-08 1.17E-08 1.20E-08 1.21E-08 1.20E-08 1.25E-08 1.19E-08 1.20E-08 1.12E-08 1.13E-08 1.02E-08 9.39E-09 1.06E-08 2.09E-10 1.11E-08 9.99E-09 1.19E-08 2.10E-10 1.25E-08 1.13E-08 1.38E-08 2.77E-10 1.45E-08 1.30E-08 1.60E-08 2.73E-10 1.68E-08 1.53E-08 2.05E-08 3.49E-10 2.15E-08 1.96E-08 2.27E-08 2.83E-10 2.35E-08 2.19E-08 2.23E-08 4.24E-10 2.34E-08 2.11E-08 1.04E-08 4.77E-10 1.17E-08 9.13E-09 -3.00E-08 PASS 3.00E-08 PASS 1.18E-08 5.43E-10 1.33E-08 1.03E-08 -6.00E-08 PASS 6.00E-08 PASS 1.35E-08 5.84E-10 1.51E-08 1.19E-08 -7.50E-08 PASS 7.50E-08 PASS 1.54E-08 6.44E-10 1.72E-08 1.36E-08 -8.33E-08 PASS 8.33E-08 PASS 1.87E-08 7.76E-10 2.08E-08 1.65E-08 -1.00E-07 PASS 1.00E-07 PASS 1.87E-08 8.16E-10 2.10E-08 1.65E-08 -1.00E-07 PASS 1.00E-07 PASS 1.74E-08 7.36E-10 1.94E-08 1.53E-08 -1.00E-07 PASS 1.00E-07 PASS An ISO 9001:2008 and DSCC Certified Company 33 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Bias Current 4 @ +/-15V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.14. Plot of Positive Bias Current 4 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 34 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.14. Raw data for Positive Bias Current 4 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Bias Current 4 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.47E-08 1.71E-08 1.41E-08 1.64E-08 1.51E-08 1.75E-08 1.52E-08 1.75E-08 1.35E-08 1.57E-08 1.45E-08 1.64E-08 1.43E-08 1.63E-08 1.36E-08 1.55E-08 1.42E-08 1.61E-08 1.26E-08 1.45E-08 1.03E-08 1.03E-08 1.05E-08 1.05E-08 50 2.19E-08 2.10E-08 2.25E-08 2.24E-08 2.02E-08 1.98E-08 1.96E-08 1.87E-08 1.92E-08 1.74E-08 1.02E-08 1.05E-08 24hr Anneal 60 2.43E-08 2.32E-08 2.49E-08 2.47E-08 2.24E-08 2.01E-08 1.97E-08 1.89E-08 1.96E-08 1.75E-08 1.02E-08 1.05E-08 168hr Anneal 70 2.40E-08 2.29E-08 2.47E-08 2.45E-08 2.22E-08 1.86E-08 1.83E-08 1.77E-08 1.84E-08 1.63E-08 1.02E-08 1.05E-08 0 1.14E-08 1.10E-08 1.15E-08 1.15E-08 1.05E-08 1.13E-08 1.13E-08 1.07E-08 1.12E-08 9.93E-09 1.02E-08 1.05E-08 Total 10 1.27E-08 1.23E-08 1.29E-08 1.31E-08 1.16E-08 1.27E-08 1.26E-08 1.19E-08 1.25E-08 1.11E-08 1.03E-08 1.05E-08 1.12E-08 4.41E-10 1.24E-08 9.96E-09 1.25E-08 5.77E-10 1.41E-08 1.09E-08 1.45E-08 7.03E-10 1.64E-08 1.26E-08 1.68E-08 7.51E-10 1.89E-08 1.48E-08 2.16E-08 9.72E-10 2.43E-08 1.89E-08 2.39E-08 1.07E-09 2.68E-08 2.10E-08 2.36E-08 1.08E-09 2.66E-08 2.07E-08 1.09E-08 5.89E-10 1.25E-08 9.27E-09 -3.00E-08 PASS 3.00E-08 PASS 1.22E-08 6.79E-10 1.40E-08 1.03E-08 -6.00E-08 PASS 6.00E-08 PASS 1.38E-08 7.43E-10 1.59E-08 1.18E-08 -7.50E-08 PASS 7.50E-08 PASS 1.57E-08 7.91E-10 1.79E-08 1.36E-08 -8.33E-08 PASS 8.33E-08 PASS 1.89E-08 9.55E-10 2.16E-08 1.63E-08 -1.00E-07 PASS 1.00E-07 PASS 1.92E-08 1.03E-09 2.20E-08 1.63E-08 -1.00E-07 PASS 1.00E-07 PASS 1.79E-08 9.46E-10 2.04E-08 1.53E-08 -1.00E-07 PASS 1.00E-07 PASS An ISO 9001:2008 and DSCC Certified Company 35 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Bias Current 1 @ +/-15V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.15. Plot of Negative Bias Current 1 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 36 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.15. Raw data for Negative Bias Current 1 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Bias Current 1 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.36E-08 1.59E-08 1.38E-08 1.60E-08 1.46E-08 1.69E-08 1.46E-08 1.70E-08 1.32E-08 1.55E-08 1.34E-08 1.53E-08 1.41E-08 1.60E-08 1.39E-08 1.58E-08 1.43E-08 1.63E-08 1.29E-08 1.47E-08 9.91E-09 9.95E-09 1.01E-08 1.02E-08 50 2.03E-08 2.04E-08 2.20E-08 2.19E-08 1.99E-08 1.84E-08 1.93E-08 1.93E-08 1.96E-08 1.77E-08 9.91E-09 1.01E-08 24hr Anneal 60 2.26E-08 2.27E-08 2.44E-08 2.40E-08 2.20E-08 1.86E-08 1.94E-08 1.94E-08 1.98E-08 1.78E-08 9.86E-09 1.01E-08 168hr Anneal 70 2.22E-08 2.22E-08 2.40E-08 2.38E-08 2.18E-08 1.73E-08 1.80E-08 1.81E-08 1.86E-08 1.66E-08 9.91E-09 1.01E-08 0 1.04E-08 1.07E-08 1.09E-08 1.10E-08 1.02E-08 1.03E-08 1.10E-08 1.09E-08 1.13E-08 1.02E-08 9.89E-09 1.01E-08 Total 10 1.18E-08 1.20E-08 1.24E-08 1.25E-08 1.14E-08 1.17E-08 1.24E-08 1.22E-08 1.26E-08 1.13E-08 9.93E-09 1.01E-08 1.07E-08 3.60E-10 1.16E-08 9.67E-09 1.20E-08 4.69E-10 1.33E-08 1.07E-08 1.40E-08 6.10E-10 1.56E-08 1.23E-08 1.63E-08 6.67E-10 1.81E-08 1.44E-08 2.09E-08 9.76E-10 2.36E-08 1.82E-08 2.31E-08 1.01E-09 2.59E-08 2.04E-08 2.28E-08 1.02E-09 2.56E-08 2.00E-08 1.07E-08 4.66E-10 1.20E-08 9.45E-09 -3.00E-08 PASS 3.00E-08 PASS 1.20E-08 5.33E-10 1.35E-08 1.06E-08 -6.00E-08 PASS 6.00E-08 PASS 1.37E-08 6.00E-10 1.54E-08 1.21E-08 -7.50E-08 PASS 7.50E-08 PASS 1.56E-08 6.48E-10 1.74E-08 1.39E-08 -8.33E-08 PASS 8.33E-08 PASS 1.89E-08 8.02E-10 2.11E-08 1.67E-08 -1.00E-07 PASS 1.00E-07 PASS 1.90E-08 8.39E-10 2.13E-08 1.67E-08 -1.00E-07 PASS 1.00E-07 PASS 1.77E-08 7.57E-10 1.98E-08 1.56E-08 -1.00E-07 PASS 1.00E-07 PASS An ISO 9001:2008 and DSCC Certified Company 37 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Bias Current 2 @ +/-15V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.16. Plot of Negative Bias Current 2 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 38 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.16. Raw data for Negative Bias Current 2 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Bias Current 2 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.45E-08 1.69E-08 1.34E-08 1.57E-08 1.45E-08 1.69E-08 1.49E-08 1.74E-08 1.37E-08 1.60E-08 1.47E-08 1.68E-08 1.42E-08 1.63E-08 1.43E-08 1.63E-08 1.27E-08 1.46E-08 1.33E-08 1.53E-08 1.06E-08 1.07E-08 9.87E-09 9.90E-09 50 2.16E-08 2.03E-08 2.18E-08 2.22E-08 2.06E-08 2.04E-08 1.98E-08 1.98E-08 1.78E-08 1.86E-08 1.07E-08 9.85E-09 24hr Anneal 60 2.42E-08 2.25E-08 2.40E-08 2.45E-08 2.27E-08 2.06E-08 1.99E-08 1.99E-08 1.77E-08 1.87E-08 1.06E-08 9.86E-09 168hr Anneal 70 2.40E-08 2.16E-08 2.36E-08 2.42E-08 2.26E-08 1.89E-08 1.84E-08 1.84E-08 1.62E-08 1.74E-08 1.06E-08 9.85E-09 0 1.14E-08 1.02E-08 1.10E-08 1.12E-08 1.06E-08 1.15E-08 1.10E-08 1.12E-08 9.66E-09 1.04E-08 1.06E-08 9.88E-09 Total 10 1.26E-08 1.16E-08 1.24E-08 1.26E-08 1.18E-08 1.29E-08 1.25E-08 1.25E-08 1.10E-08 1.17E-08 1.07E-08 9.88E-09 1.09E-08 4.88E-10 1.22E-08 9.53E-09 1.22E-08 4.71E-10 1.35E-08 1.09E-08 1.42E-08 6.27E-10 1.59E-08 1.25E-08 1.66E-08 6.73E-10 1.84E-08 1.47E-08 2.13E-08 7.98E-10 2.35E-08 1.91E-08 2.36E-08 9.16E-10 2.61E-08 2.11E-08 2.32E-08 1.10E-09 2.62E-08 2.02E-08 1.07E-08 7.26E-10 1.27E-08 8.74E-09 -3.00E-08 PASS 3.00E-08 PASS 1.21E-08 7.66E-10 1.42E-08 1.00E-08 -6.00E-08 PASS 6.00E-08 PASS 1.38E-08 8.05E-10 1.60E-08 1.16E-08 -7.50E-08 PASS 7.50E-08 PASS 1.59E-08 8.97E-10 1.83E-08 1.34E-08 -8.33E-08 PASS 8.33E-08 PASS 1.93E-08 1.08E-09 2.22E-08 1.63E-08 -1.00E-07 PASS 1.00E-07 PASS 1.94E-08 1.15E-09 2.25E-08 1.62E-08 -1.00E-07 PASS 1.00E-07 PASS 1.79E-08 1.07E-09 2.08E-08 1.49E-08 -1.00E-07 PASS 1.00E-07 PASS An ISO 9001:2008 and DSCC Certified Company 39 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Bias Current 3 @ +/-15V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.17. Plot of Negative Bias Current 3 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 40 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.17. Raw data for Negative Bias Current 3 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Bias Current 3 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.35E-08 1.58E-08 1.37E-08 1.60E-08 1.40E-08 1.62E-08 1.41E-08 1.64E-08 1.38E-08 1.61E-08 1.43E-08 1.64E-08 1.36E-08 1.55E-08 1.39E-08 1.58E-08 1.29E-08 1.49E-08 1.30E-08 1.49E-08 1.02E-08 1.02E-08 9.48E-09 9.47E-09 50 2.04E-08 2.06E-08 2.08E-08 2.13E-08 2.07E-08 1.99E-08 1.88E-08 1.92E-08 1.81E-08 1.82E-08 1.02E-08 9.45E-09 24hr Anneal 60 2.26E-08 2.27E-08 2.30E-08 2.33E-08 2.28E-08 2.02E-08 1.89E-08 1.92E-08 1.80E-08 1.83E-08 1.02E-08 9.46E-09 168hr Anneal 70 2.21E-08 2.20E-08 2.27E-08 2.30E-08 2.29E-08 1.85E-08 1.75E-08 1.77E-08 1.66E-08 1.69E-08 1.02E-08 9.49E-09 0 1.04E-08 1.03E-08 1.06E-08 1.06E-08 1.07E-08 1.11E-08 1.06E-08 1.08E-08 9.84E-09 1.01E-08 1.02E-08 9.45E-09 Total 10 1.17E-08 1.18E-08 1.20E-08 1.20E-08 1.20E-08 1.26E-08 1.19E-08 1.21E-08 1.12E-08 1.14E-08 1.02E-08 9.46E-09 1.05E-08 1.66E-10 1.10E-08 1.01E-08 1.19E-08 1.71E-10 1.24E-08 1.14E-08 1.38E-08 2.28E-10 1.44E-08 1.32E-08 1.61E-08 2.30E-10 1.67E-08 1.55E-08 2.08E-08 3.16E-10 2.16E-08 1.99E-08 2.29E-08 2.61E-10 2.36E-08 2.22E-08 2.25E-08 4.34E-10 2.37E-08 2.13E-08 1.05E-08 4.99E-10 1.18E-08 9.08E-09 -3.00E-08 PASS 3.00E-08 PASS 1.18E-08 5.68E-10 1.34E-08 1.03E-08 -6.00E-08 PASS 6.00E-08 PASS 1.35E-08 5.84E-10 1.52E-08 1.19E-08 -7.50E-08 PASS 7.50E-08 PASS 1.55E-08 6.16E-10 1.72E-08 1.38E-08 -8.33E-08 PASS 8.33E-08 PASS 1.88E-08 7.81E-10 2.10E-08 1.67E-08 -1.00E-07 PASS 1.00E-07 PASS 1.89E-08 8.48E-10 2.12E-08 1.66E-08 -1.00E-07 PASS 1.00E-07 PASS 1.75E-08 7.51E-10 1.95E-08 1.54E-08 -1.00E-07 PASS 1.00E-07 PASS An ISO 9001:2008 and DSCC Certified Company 41 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Bias Current 4 @ +/-15V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.18. Plot of Negative Bias Current 4 @ +/-15V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 42 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.18. Raw data for Negative Bias Current 4 @ +/-15V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Bias Current 4 @ +/-15V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.48E-08 1.72E-08 1.43E-08 1.65E-08 1.53E-08 1.77E-08 1.52E-08 1.76E-08 1.36E-08 1.60E-08 1.43E-08 1.65E-08 1.45E-08 1.65E-08 1.38E-08 1.57E-08 1.42E-08 1.62E-08 1.27E-08 1.45E-08 1.04E-08 1.04E-08 1.05E-08 1.06E-08 50 2.21E-08 2.11E-08 2.30E-08 2.25E-08 2.05E-08 1.98E-08 1.98E-08 1.89E-08 1.94E-08 1.75E-08 1.03E-08 1.05E-08 24hr Anneal 60 2.46E-08 2.34E-08 2.54E-08 2.49E-08 2.26E-08 2.01E-08 1.99E-08 1.92E-08 1.97E-08 1.76E-08 1.03E-08 1.05E-08 168hr Anneal 70 2.42E-08 2.31E-08 2.52E-08 2.45E-08 2.24E-08 1.86E-08 1.84E-08 1.79E-08 1.84E-08 1.64E-08 1.03E-08 1.06E-08 0 1.13E-08 1.10E-08 1.16E-08 1.15E-08 1.05E-08 1.13E-08 1.13E-08 1.07E-08 1.12E-08 9.96E-09 1.03E-08 1.05E-08 Total 10 1.28E-08 1.24E-08 1.30E-08 1.30E-08 1.17E-08 1.26E-08 1.27E-08 1.20E-08 1.25E-08 1.11E-08 1.04E-08 1.06E-08 1.12E-08 4.52E-10 1.24E-08 9.95E-09 1.26E-08 5.68E-10 1.41E-08 1.10E-08 1.46E-08 7.09E-10 1.66E-08 1.27E-08 1.70E-08 7.27E-10 1.90E-08 1.50E-08 2.18E-08 9.97E-10 2.46E-08 1.91E-08 2.42E-08 1.14E-09 2.73E-08 2.11E-08 2.39E-08 1.13E-09 2.70E-08 2.08E-08 1.09E-08 5.73E-10 1.25E-08 9.32E-09 -3.00E-08 PASS 3.00E-08 PASS 1.22E-08 6.50E-10 1.40E-08 1.04E-08 -6.00E-08 PASS 6.00E-08 PASS 1.39E-08 7.23E-10 1.59E-08 1.19E-08 -7.50E-08 PASS 7.50E-08 PASS 1.59E-08 8.16E-10 1.81E-08 1.36E-08 -8.33E-08 PASS 8.33E-08 PASS 1.91E-08 9.74E-10 2.18E-08 1.64E-08 -1.00E-07 PASS 1.00E-07 PASS 1.93E-08 1.02E-09 2.21E-08 1.65E-08 -1.00E-07 PASS 1.00E-07 PASS 1.79E-08 9.16E-10 2.05E-08 1.54E-08 -1.00E-07 PASS 1.00E-07 PASS An ISO 9001:2008 and DSCC Certified Company 43 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Common Mode Rejection Ratio 1 (dB) 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.19. Plot of Common Mode Rejection Ratio 1 (dB) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 44 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.19. Raw data for Common Mode Rejection Ratio 1 (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection Ratio 1 (dB) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.11E+02 1.07E+02 1.13E+02 1.14E+02 1.07E+02 1.10E+02 1.15E+02 1.16E+02 1.09E+02 1.18E+02 1.13E+02 1.09E+02 24hr Anneal 60 1.11E+02 1.07E+02 1.14E+02 1.15E+02 1.08E+02 1.11E+02 1.16E+02 1.17E+02 1.10E+02 1.17E+02 1.13E+02 1.09E+02 168hr Anneal 70 1.13E+02 1.08E+02 1.15E+02 1.17E+02 1.09E+02 1.12E+02 1.19E+02 1.19E+02 1.11E+02 1.21E+02 1.12E+02 1.09E+02 1.11E+02 3.42E+00 1.20E+02 1.01E+02 1.10E+02 3.26E+00 1.19E+02 1.01E+02 1.11E+02 3.50E+00 1.20E+02 1.01E+02 1.12E+02 3.98E+00 1.23E+02 1.01E+02 1.15E+02 4.25E+00 1.27E+02 1.03E+02 9.60E+01 PASS 1.14E+02 3.78E+00 1.24E+02 1.03E+02 9.40E+01 PASS 1.14E+02 3.74E+00 1.25E+02 1.04E+02 9.40E+01 PASS 1.16E+02 4.68E+00 1.29E+02 1.04E+02 9.40E+01 PASS 0 1.15E+02 1.09E+02 1.17E+02 1.20E+02 1.10E+02 1.14E+02 1.22E+02 1.25E+02 1.12E+02 1.27E+02 1.12E+02 1.09E+02 Total 10 1.11E+02 1.07E+02 1.14E+02 1.16E+02 1.08E+02 1.13E+02 1.19E+02 1.22E+02 1.11E+02 1.21E+02 1.13E+02 1.09E+02 Dose (krad(Si)) 20 30 1.12E+02 1.11E+02 1.07E+02 1.07E+02 1.14E+02 1.13E+02 1.15E+02 1.15E+02 1.08E+02 1.07E+02 1.11E+02 1.11E+02 1.18E+02 1.17E+02 1.20E+02 1.18E+02 1.10E+02 1.10E+02 1.21E+02 1.20E+02 1.12E+02 1.13E+02 1.09E+02 1.09E+02 1.14E+02 4.80E+00 1.27E+02 1.01E+02 1.11E+02 3.68E+00 1.21E+02 1.01E+02 1.11E+02 3.46E+00 1.20E+02 1.01E+02 1.20E+02 6.50E+00 1.38E+02 1.02E+02 9.70E+01 PASS 1.17E+02 4.78E+00 1.30E+02 1.04E+02 9.70E+01 PASS 1.16E+02 4.83E+00 1.29E+02 1.03E+02 9.70E+01 PASS An ISO 9001:2008 and DSCC Certified Company 45 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Common Mode Rejection Ratio 2 (dB) 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.20. Plot of Common Mode Rejection Ratio 2 (dB) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 46 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.20. Raw data for Common Mode Rejection Ratio 2 (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection Ratio 2 (dB) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.09E+02 1.11E+02 1.10E+02 1.11E+02 1.03E+02 1.08E+02 1.13E+02 1.21E+02 1.09E+02 1.07E+02 1.15E+02 1.07E+02 24hr Anneal 60 1.10E+02 1.12E+02 1.10E+02 1.12E+02 1.04E+02 1.09E+02 1.13E+02 1.22E+02 1.09E+02 1.08E+02 1.15E+02 1.07E+02 168hr Anneal 70 1.10E+02 1.13E+02 1.11E+02 1.13E+02 1.04E+02 1.10E+02 1.15E+02 1.26E+02 1.10E+02 1.08E+02 1.15E+02 1.07E+02 1.09E+02 3.33E+00 1.18E+02 1.00E+02 1.09E+02 3.21E+00 1.18E+02 9.99E+01 1.09E+02 3.40E+00 1.19E+02 1.00E+02 1.10E+02 3.54E+00 1.20E+02 1.00E+02 1.13E+02 6.17E+00 1.29E+02 9.56E+01 9.60E+01 PASS 1.12E+02 5.51E+00 1.27E+02 9.66E+01 9.40E+01 PASS 1.12E+02 5.87E+00 1.28E+02 9.62E+01 9.40E+01 PASS 1.14E+02 7.41E+00 1.34E+02 9.36E+01 9.40E+01 PASS 0 1.12E+02 1.14E+02 1.13E+02 1.14E+02 1.05E+02 1.11E+02 1.17E+02 1.44E+02 1.11E+02 1.09E+02 1.15E+02 1.07E+02 Total 10 1.10E+02 1.12E+02 1.11E+02 1.12E+02 1.04E+02 1.10E+02 1.15E+02 1.28E+02 1.11E+02 1.08E+02 1.15E+02 1.07E+02 Dose (krad(Si)) 20 30 1.10E+02 1.09E+02 1.12E+02 1.11E+02 1.11E+02 1.10E+02 1.12E+02 1.12E+02 1.04E+02 1.03E+02 1.09E+02 1.09E+02 1.14E+02 1.14E+02 1.25E+02 1.23E+02 1.10E+02 1.10E+02 1.08E+02 1.08E+02 1.15E+02 1.15E+02 1.07E+02 1.07E+02 1.11E+02 3.95E+00 1.22E+02 1.01E+02 1.10E+02 3.53E+00 1.20E+02 1.00E+02 1.09E+02 3.42E+00 1.19E+02 1.00E+02 1.19E+02 1.45E+01 1.58E+02 7.88E+01 9.70E+01 PASS 1.14E+02 8.01E+00 1.36E+02 9.25E+01 9.70E+01 PASS 1.13E+02 6.99E+00 1.33E+02 9.42E+01 9.70E+01 PASS An ISO 9001:2008 and DSCC Certified Company 47 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Common Mode Rejection Ratio 3 (dB) 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.21. Plot of Common Mode Rejection Ratio 3 (dB) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 48 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.21. Raw data for Common Mode Rejection Ratio 3 (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection Ratio 3 (dB) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.08E+02 1.14E+02 1.15E+02 1.20E+02 1.08E+02 1.10E+02 1.22E+02 1.23E+02 1.13E+02 1.10E+02 1.13E+02 1.21E+02 24hr Anneal 60 1.09E+02 1.16E+02 1.16E+02 1.22E+02 1.08E+02 1.11E+02 1.25E+02 1.24E+02 1.14E+02 1.10E+02 1.14E+02 1.21E+02 168hr Anneal 70 1.09E+02 1.18E+02 1.19E+02 1.29E+02 1.09E+02 1.12E+02 1.31E+02 1.32E+02 1.16E+02 1.11E+02 1.14E+02 1.21E+02 1.14E+02 5.75E+00 1.30E+02 9.83E+01 1.13E+02 5.21E+00 1.27E+02 9.87E+01 1.14E+02 5.94E+00 1.31E+02 9.81E+01 1.17E+02 8.29E+00 1.40E+02 9.43E+01 1.18E+02 7.93E+00 1.39E+02 9.58E+01 9.60E+01 PASS 1.16E+02 6.61E+00 1.34E+02 9.76E+01 9.40E+01 PASS 1.17E+02 7.27E+00 1.37E+02 9.68E+01 9.40E+01 PASS 1.20E+02 1.05E+01 1.49E+02 9.15E+01 9.40E+01 PASS 0 1.11E+02 1.21E+02 1.23E+02 1.45E+02 1.10E+02 1.14E+02 1.34E+02 1.35E+02 1.18E+02 1.13E+02 1.13E+02 1.21E+02 Total 10 1.09E+02 1.17E+02 1.18E+02 1.24E+02 1.09E+02 1.12E+02 1.39E+02 1.38E+02 1.16E+02 1.12E+02 1.14E+02 1.21E+02 Dose (krad(Si)) 20 30 1.09E+02 1.09E+02 1.16E+02 1.16E+02 1.17E+02 1.16E+02 1.24E+02 1.22E+02 1.09E+02 1.08E+02 1.11E+02 1.11E+02 1.31E+02 1.26E+02 1.29E+02 1.26E+02 1.15E+02 1.14E+02 1.11E+02 1.10E+02 1.13E+02 1.14E+02 1.21E+02 1.22E+02 1.22E+02 1.43E+01 1.61E+02 8.28E+01 1.15E+02 6.55E+00 1.33E+02 9.74E+01 1.15E+02 6.28E+00 1.32E+02 9.75E+01 1.23E+02 1.10E+01 1.53E+02 9.24E+01 9.70E+01 PASS 1.23E+02 1.40E+01 1.62E+02 8.50E+01 9.70E+01 PASS 1.19E+02 9.63E+00 1.46E+02 9.29E+01 9.70E+01 PASS An ISO 9001:2008 and DSCC Certified Company 49 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Common Mode Rejection Ratio 4 (dB) 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.22. Plot of Common Mode Rejection Ratio 4 (dB) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 50 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.22. Raw data for Common Mode Rejection Ratio 4 (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection Ratio 4 (dB) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.09E+02 1.03E+02 1.09E+02 1.16E+02 1.08E+02 1.08E+02 1.14E+02 1.09E+02 1.06E+02 1.11E+02 1.13E+02 1.08E+02 24hr Anneal 60 1.10E+02 1.04E+02 1.09E+02 1.17E+02 1.08E+02 1.08E+02 1.15E+02 1.09E+02 1.07E+02 1.12E+02 1.13E+02 1.09E+02 168hr Anneal 70 1.10E+02 1.04E+02 1.10E+02 1.20E+02 1.09E+02 1.09E+02 1.17E+02 1.10E+02 1.07E+02 1.13E+02 1.13E+02 1.08E+02 1.09E+02 4.85E+00 1.23E+02 9.61E+01 1.09E+02 4.49E+00 1.21E+02 9.66E+01 1.10E+02 4.96E+00 1.23E+02 9.61E+01 1.11E+02 5.83E+00 1.27E+02 9.49E+01 1.10E+02 3.30E+00 1.20E+02 1.01E+02 9.60E+01 PASS 1.10E+02 3.11E+00 1.18E+02 1.01E+02 9.40E+01 PASS 1.10E+02 3.31E+00 1.19E+02 1.01E+02 9.40E+01 PASS 1.11E+02 3.78E+00 1.22E+02 1.01E+02 9.40E+01 PASS 0 1.12E+02 1.05E+02 1.11E+02 1.23E+02 1.10E+02 1.10E+02 1.17E+02 1.11E+02 1.09E+02 1.15E+02 1.13E+02 1.08E+02 Total 10 1.10E+02 1.04E+02 1.10E+02 1.18E+02 1.09E+02 1.09E+02 1.17E+02 1.10E+02 1.08E+02 1.13E+02 1.13E+02 1.08E+02 Dose (krad(Si)) 20 30 1.10E+02 1.09E+02 1.04E+02 1.04E+02 1.09E+02 1.09E+02 1.18E+02 1.17E+02 1.08E+02 1.08E+02 1.09E+02 1.09E+02 1.16E+02 1.15E+02 1.10E+02 1.09E+02 1.07E+02 1.07E+02 1.13E+02 1.12E+02 1.13E+02 1.13E+02 1.08E+02 1.08E+02 1.12E+02 6.89E+00 1.31E+02 9.32E+01 1.10E+02 5.27E+00 1.25E+02 9.56E+01 1.10E+02 5.18E+00 1.24E+02 9.56E+01 1.12E+02 3.55E+00 1.22E+02 1.03E+02 9.70E+01 PASS 1.12E+02 3.70E+00 1.22E+02 1.01E+02 9.70E+01 PASS 1.11E+02 3.56E+00 1.21E+02 1.01E+02 9.70E+01 PASS An ISO 9001:2008 and DSCC Certified Company 51 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Power Supply Rejection Ratio 1 (dB) 1.60E+02 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.23. Plot of Power Supply Rejection Ratio 1 (dB) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 52 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.23. Raw data for Power Supply Rejection Ratio 1 (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio 1 (dB) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.24E+02 1.30E+02 1.19E+02 1.47E+02 1.25E+02 1.33E+02 1.31E+02 1.42E+02 1.19E+02 1.42E+02 1.37E+02 1.31E+02 24hr Anneal 60 1.25E+02 1.37E+02 1.19E+02 1.36E+02 1.26E+02 1.35E+02 1.27E+02 1.42E+02 1.20E+02 1.42E+02 1.52E+02 1.34E+02 168hr Anneal 70 1.28E+02 1.37E+02 1.17E+02 1.31E+02 1.29E+02 1.44E+02 1.25E+02 1.50E+02 1.22E+02 1.35E+02 1.41E+02 1.30E+02 1.28E+02 6.97E+00 1.47E+02 1.09E+02 1.29E+02 1.08E+01 1.59E+02 9.95E+01 1.29E+02 7.67E+00 1.50E+02 1.08E+02 1.28E+02 7.33E+00 1.49E+02 1.08E+02 1.34E+02 8.66E+00 1.58E+02 1.10E+02 9.67E+01 PASS 1.33E+02 9.20E+00 1.59E+02 1.08E+02 9.40E+01 PASS 1.33E+02 9.52E+00 1.59E+02 1.07E+02 9.40E+01 PASS 1.35E+02 1.17E+01 1.67E+02 1.03E+02 9.40E+01 PASS 0 1.30E+02 1.40E+02 1.18E+02 1.29E+02 1.31E+02 1.50E+02 1.26E+02 1.39E+02 1.24E+02 1.34E+02 1.52E+02 1.30E+02 Total 10 1.28E+02 1.40E+02 1.18E+02 1.30E+02 1.28E+02 1.45E+02 1.27E+02 1.38E+02 1.22E+02 1.36E+02 1.36E+02 1.30E+02 Dose (krad(Si)) 20 30 1.28E+02 1.28E+02 1.34E+02 1.38E+02 1.18E+02 1.19E+02 1.31E+02 1.32E+02 1.28E+02 1.25E+02 1.41E+02 1.39E+02 1.28E+02 1.28E+02 1.55E+02 1.43E+02 1.22E+02 1.22E+02 1.45E+02 1.38E+02 1.37E+02 1.39E+02 1.32E+02 1.35E+02 1.30E+02 7.93E+00 1.51E+02 1.08E+02 1.29E+02 7.97E+00 1.51E+02 1.07E+02 1.28E+02 5.77E+00 1.44E+02 1.12E+02 1.34E+02 1.05E+01 1.63E+02 1.06E+02 1.00E+02 PASS 1.34E+02 9.01E+00 1.58E+02 1.09E+02 1.00E+02 PASS 1.38E+02 1.34E+01 1.75E+02 1.01E+02 9.80E+01 PASS An ISO 9001:2008 and DSCC Certified Company 53 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Power Supply Rejection Ratio 2 (dB) 1.60E+02 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.24. Plot of Power Supply Rejection Ratio 2 (dB) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 54 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.24. Raw data for Power Supply Rejection Ratio 2 (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio 2 (dB) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.24E+02 1.24E+02 1.33E+02 1.23E+02 1.26E+02 1.28E+02 1.28E+02 1.26E+02 1.39E+02 1.23E+02 1.35E+02 1.29E+02 24hr Anneal 60 1.26E+02 1.24E+02 1.35E+02 1.24E+02 1.28E+02 1.29E+02 1.26E+02 1.26E+02 1.37E+02 1.21E+02 1.34E+02 1.27E+02 168hr Anneal 70 1.28E+02 1.24E+02 1.42E+02 1.25E+02 1.33E+02 1.34E+02 1.25E+02 1.24E+02 1.51E+02 1.20E+02 1.33E+02 1.28E+02 1.27E+02 3.68E+00 1.37E+02 1.17E+02 1.26E+02 3.91E+00 1.37E+02 1.15E+02 1.27E+02 4.37E+00 1.39E+02 1.15E+02 1.31E+02 7.24E+00 1.50E+02 1.11E+02 1.29E+02 7.22E+00 1.49E+02 1.09E+02 9.67E+01 PASS 1.29E+02 6.13E+00 1.45E+02 1.12E+02 9.40E+01 PASS 1.28E+02 5.71E+00 1.43E+02 1.12E+02 9.40E+01 PASS 1.31E+02 1.28E+01 1.66E+02 9.56E+01 9.40E+01 PASS 0 1.30E+02 1.24E+02 1.51E+02 1.27E+02 1.36E+02 1.36E+02 1.24E+02 1.23E+02 1.40E+02 1.20E+02 1.34E+02 1.28E+02 Total 10 1.27E+02 1.24E+02 1.44E+02 1.25E+02 1.29E+02 1.35E+02 1.25E+02 1.24E+02 1.47E+02 1.21E+02 1.32E+02 1.28E+02 Dose (krad(Si)) 20 30 1.26E+02 1.26E+02 1.25E+02 1.25E+02 1.36E+02 1.34E+02 1.25E+02 1.25E+02 1.28E+02 1.27E+02 1.32E+02 1.30E+02 1.26E+02 1.26E+02 1.24E+02 1.25E+02 1.42E+02 1.41E+02 1.22E+02 1.22E+02 1.34E+02 1.32E+02 1.27E+02 1.27E+02 1.33E+02 1.06E+01 1.62E+02 1.04E+02 1.30E+02 7.82E+00 1.51E+02 1.09E+02 1.28E+02 4.69E+00 1.41E+02 1.15E+02 1.29E+02 8.74E+00 1.53E+02 1.05E+02 1.00E+02 PASS 1.31E+02 1.06E+01 1.60E+02 1.01E+02 1.00E+02 PASS 1.29E+02 8.12E+00 1.52E+02 1.07E+02 9.80E+01 PASS An ISO 9001:2008 and DSCC Certified Company 55 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Power Supply Rejection Ratio 3 (dB) 1.60E+02 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.25. Plot of Power Supply Rejection Ratio 3 (dB) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 56 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.25. Raw data for Power Supply Rejection Ratio 3 (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio 3 (dB) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.31E+02 1.32E+02 1.37E+02 1.22E+02 1.28E+02 1.25E+02 1.72E+02 1.23E+02 1.48E+02 1.56E+02 1.35E+02 1.20E+02 24hr Anneal 60 1.32E+02 1.29E+02 1.35E+02 1.21E+02 1.31E+02 1.24E+02 1.34E+02 1.23E+02 1.45E+02 1.38E+02 1.33E+02 1.19E+02 168hr Anneal 70 1.38E+02 1.29E+02 1.31E+02 1.20E+02 1.46E+02 1.29E+02 1.33E+02 1.22E+02 1.32E+02 1.30E+02 1.30E+02 1.20E+02 1.31E+02 7.84E+00 1.53E+02 1.10E+02 1.30E+02 5.47E+00 1.45E+02 1.15E+02 1.29E+02 5.47E+00 1.44E+02 1.14E+02 1.33E+02 9.89E+00 1.60E+02 1.06E+02 1.34E+02 8.27E+00 1.56E+02 1.11E+02 9.67E+01 PASS 1.45E+02 2.09E+01 2.02E+02 8.74E+01 9.40E+01 PASS 1.33E+02 9.04E+00 1.58E+02 1.08E+02 9.40E+01 PASS 1.29E+02 4.41E+00 1.41E+02 1.17E+02 9.40E+01 PASS 0 1.50E+02 1.28E+02 1.27E+02 1.19E+02 1.41E+02 1.29E+02 1.32E+02 1.21E+02 1.31E+02 1.32E+02 1.34E+02 1.20E+02 Total 10 1.39E+02 1.27E+02 1.30E+02 1.20E+02 1.35E+02 1.31E+02 1.32E+02 1.21E+02 1.34E+02 1.34E+02 1.31E+02 1.20E+02 Dose (krad(Si)) 20 30 1.38E+02 1.42E+02 1.30E+02 1.29E+02 1.33E+02 1.35E+02 1.21E+02 1.21E+02 1.37E+02 1.30E+02 1.29E+02 1.27E+02 1.35E+02 1.42E+02 1.23E+02 1.23E+02 1.40E+02 1.36E+02 1.34E+02 1.40E+02 1.30E+02 1.31E+02 1.19E+02 1.20E+02 1.33E+02 1.23E+01 1.67E+02 9.96E+01 1.30E+02 7.40E+00 1.50E+02 1.10E+02 1.32E+02 6.97E+00 1.51E+02 1.13E+02 1.29E+02 4.49E+00 1.41E+02 1.17E+02 1.00E+02 PASS 1.30E+02 5.33E+00 1.45E+02 1.16E+02 1.00E+02 PASS 1.32E+02 6.68E+00 1.50E+02 1.14E+02 9.80E+01 PASS An ISO 9001:2008 and DSCC Certified Company 57 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Power Supply Rejection Ratio 4 (dB) 1.60E+02 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.26. Plot of Power Supply Rejection Ratio 4 (dB) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 58 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.26. Raw data for Power Supply Rejection Ratio 4 (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio 4 (dB) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.21E+02 1.22E+02 1.23E+02 1.31E+02 1.32E+02 1.23E+02 1.23E+02 1.35E+02 1.32E+02 1.28E+02 1.33E+02 1.28E+02 24hr Anneal 60 1.22E+02 1.24E+02 1.22E+02 1.29E+02 1.33E+02 1.23E+02 1.25E+02 1.36E+02 1.31E+02 1.25E+02 1.33E+02 1.29E+02 168hr Anneal 70 1.23E+02 1.24E+02 1.21E+02 1.26E+02 1.53E+02 1.26E+02 1.26E+02 1.46E+02 1.46E+02 1.22E+02 1.31E+02 1.28E+02 1.25E+02 3.86E+00 1.36E+02 1.15E+02 1.26E+02 5.19E+00 1.40E+02 1.12E+02 1.26E+02 4.88E+00 1.39E+02 1.13E+02 1.29E+02 1.33E+01 1.66E+02 9.30E+01 1.30E+02 7.61E+00 1.51E+02 1.09E+02 9.67E+01 PASS 1.28E+02 5.12E+00 1.42E+02 1.14E+02 9.40E+01 PASS 1.28E+02 5.63E+00 1.43E+02 1.13E+02 9.40E+01 PASS 1.33E+02 1.15E+01 1.65E+02 1.01E+02 9.40E+01 PASS 0 1.24E+02 1.25E+02 1.21E+02 1.24E+02 1.47E+02 1.26E+02 1.26E+02 1.58E+02 1.47E+02 1.24E+02 1.32E+02 1.27E+02 Total 10 1.23E+02 1.24E+02 1.22E+02 1.25E+02 1.37E+02 1.27E+02 1.27E+02 1.58E+02 1.43E+02 1.25E+02 1.29E+02 1.27E+02 Dose (krad(Si)) 20 30 1.22E+02 1.22E+02 1.23E+02 1.23E+02 1.22E+02 1.23E+02 1.26E+02 1.26E+02 1.39E+02 1.32E+02 1.26E+02 1.24E+02 1.26E+02 1.25E+02 1.43E+02 1.41E+02 1.35E+02 1.35E+02 1.25E+02 1.26E+02 1.29E+02 1.28E+02 1.30E+02 1.29E+02 1.28E+02 1.09E+01 1.58E+02 9.83E+01 1.26E+02 6.22E+00 1.43E+02 1.09E+02 1.27E+02 7.26E+00 1.46E+02 1.07E+02 1.36E+02 1.55E+01 1.79E+02 9.40E+01 1.00E+02 PASS 1.36E+02 1.43E+01 1.75E+02 9.69E+01 1.00E+02 PASS 1.31E+02 7.94E+00 1.53E+02 1.09E+02 9.80E+01 PASS An ISO 9001:2008 and DSCC Certified Company 59 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Open Loop Gain 1 RL=10k VO=+/-10V (V/mV) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 6.00E+04 5.00E+04 4.00E+04 3.00E+04 2.00E+04 1.00E+04 0.00E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.27. Plot of Open Loop Gain 1 RL=10k VO=+/-10V (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 60 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.27. Raw data for Open Loop Gain 1 RL=10k VO=+/-10V (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Open Loop Gain 1 RL=10k VO=+/-10V (V/mV) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.00E+04 4.86E+04 4.58E+04 4.55E+04 4.84E+04 3.21E+04 3.97E+04 4.62E+04 4.96E+04 4.64E+04 5.35E+04 4.78E+04 24hr Anneal 60 5.84E+04 4.49E+04 5.58E+04 5.09E+04 5.13E+04 5.20E+04 4.85E+04 3.67E+04 4.30E+04 4.77E+04 4.80E+04 5.20E+04 168hr Anneal 70 5.26E+04 4.56E+04 4.98E+04 4.80E+04 5.23E+04 4.40E+04 4.99E+04 5.64E+04 5.68E+04 4.99E+04 5.12E+04 5.63E+04 5.28E+04 5.31E+03 6.74E+04 3.82E+04 4.57E+04 3.46E+03 5.51E+04 3.62E+04 5.23E+04 5.18E+03 6.65E+04 3.81E+04 4.96E+04 2.96E+03 5.78E+04 4.15E+04 5.11E+04 5.74E+03 6.68E+04 3.53E+04 1.67E+02 PASS 4.28E+04 7.00E+03 6.20E+04 2.36E+04 1.00E+02 PASS 4.56E+04 5.91E+03 6.18E+04 2.94E+04 1.00E+02 PASS 5.14E+04 5.33E+03 6.60E+04 3.68E+04 1.00E+02 PASS 0 5.36E+04 4.68E+04 5.23E+04 4.83E+04 5.53E+04 3.76E+04 5.09E+04 5.69E+04 4.73E+04 5.72E+04 5.44E+04 5.11E+04 Total 10 4.75E+04 5.74E+04 5.42E+04 5.12E+04 6.04E+04 5.46E+04 4.99E+04 5.47E+04 5.08E+04 6.90E+04 6.30E+04 5.53E+04 Dose (krad(Si)) 20 30 5.03E+04 4.37E+04 4.89E+04 5.74E+04 5.25E+04 5.53E+04 5.05E+04 5.40E+04 5.63E+04 5.37E+04 4.93E+04 5.07E+04 4.80E+04 5.06E+04 5.21E+04 4.27E+04 5.75E+04 5.26E+04 5.24E+04 5.88E+04 4.48E+04 6.01E+04 6.08E+04 5.83E+04 5.13E+04 3.60E+03 6.12E+04 4.14E+04 5.41E+04 5.09E+03 6.81E+04 4.02E+04 5.17E+04 2.89E+03 5.96E+04 4.38E+04 5.00E+04 8.09E+03 7.22E+04 2.78E+04 1.20E+03 PASS 5.58E+04 7.71E+03 7.69E+04 3.47E+04 5.00E+02 PASS 5.19E+04 3.67E+03 6.19E+04 4.18E+04 2.00E+02 PASS An ISO 9001:2008 and DSCC Certified Company 61 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Open Loop Gain 2 RL=10k VO=+/-10V (V/mV) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 7.00E+04 6.00E+04 5.00E+04 4.00E+04 3.00E+04 2.00E+04 1.00E+04 0.00E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.28. Plot of Open Loop Gain 2 RL=10k VO=+/-10V (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 62 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.28. Raw data for Open Loop Gain 2 RL=10k VO=+/-10V (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Open Loop Gain 2 RL=10k VO=+/-10V (V/mV) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.53E+04 5.29E+04 5.32E+04 5.02E+04 6.55E+04 4.44E+04 5.39E+04 5.24E+04 5.04E+04 5.43E+04 5.09E+04 7.49E+04 24hr Anneal 60 4.25E+04 5.88E+04 5.07E+04 4.91E+04 6.12E+04 4.03E+04 4.56E+04 5.05E+04 5.16E+04 5.57E+04 4.87E+04 5.78E+04 168hr Anneal 70 4.79E+04 5.27E+04 4.29E+04 4.62E+04 5.90E+04 4.75E+04 4.97E+04 5.03E+04 4.55E+04 4.74E+04 5.32E+04 5.99E+04 5.46E+04 7.35E+03 7.47E+04 3.44E+04 5.34E+04 7.48E+03 7.39E+04 3.29E+04 5.25E+04 7.61E+03 7.33E+04 3.16E+04 4.98E+04 6.25E+03 6.69E+04 3.26E+04 5.23E+04 6.10E+03 6.90E+04 3.55E+04 1.67E+02 PASS 5.11E+04 4.05E+03 6.22E+04 4.00E+04 1.00E+02 PASS 4.87E+04 5.95E+03 6.51E+04 3.24E+04 1.00E+02 PASS 4.81E+04 1.94E+03 5.34E+04 4.28E+04 1.00E+02 PASS 0 6.34E+04 4.97E+04 4.90E+04 7.72E+04 5.94E+04 6.88E+04 5.73E+04 5.04E+04 5.84E+04 5.82E+04 5.67E+04 7.21E+04 Total 10 5.04E+04 5.70E+04 6.15E+04 6.21E+04 4.11E+04 4.83E+04 5.84E+04 5.04E+04 5.04E+04 5.56E+04 5.42E+04 5.32E+04 Dose (krad(Si)) 20 30 4.42E+04 5.42E+04 5.82E+04 6.38E+04 5.70E+04 4.35E+04 5.89E+04 5.43E+04 6.19E+04 5.71E+04 4.88E+04 5.48E+04 4.80E+04 5.95E+04 5.14E+04 5.26E+04 5.26E+04 5.16E+04 4.75E+04 4.28E+04 5.63E+04 5.30E+04 5.25E+04 5.78E+04 5.98E+04 1.16E+04 9.14E+04 2.81E+04 5.44E+04 8.80E+03 7.86E+04 3.03E+04 5.60E+04 6.87E+03 7.49E+04 3.72E+04 5.86E+04 6.59E+03 7.67E+04 4.05E+04 1.20E+03 PASS 5.26E+04 4.21E+03 6.42E+04 4.11E+04 5.00E+02 PASS 4.96E+04 2.24E+03 5.58E+04 4.35E+04 2.00E+02 PASS An ISO 9001:2008 and DSCC Certified Company 63 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Open Loop Gain 3 RL=10k VO=+/-10V (V/mV) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 6.00E+04 5.00E+04 4.00E+04 3.00E+04 2.00E+04 1.00E+04 0.00E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.29. Plot of Open Loop Gain 3 RL=10k VO=+/-10V (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 64 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.29. Raw data for Open Loop Gain 3 RL=10k VO=+/-10V (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Open Loop Gain 3 RL=10k VO=+/-10V (V/mV) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 5.05E+04 5.20E+04 4.94E+04 4.89E+04 4.23E+04 4.72E+04 4.28E+04 4.13E+04 5.06E+04 4.24E+04 5.15E+04 5.67E+04 24hr Anneal 60 3.95E+04 5.01E+04 3.99E+04 4.70E+04 5.13E+04 3.73E+04 5.82E+04 5.80E+04 4.30E+04 5.06E+04 6.29E+04 4.69E+04 168hr Anneal 70 4.84E+04 5.92E+04 5.81E+04 5.21E+04 4.32E+04 4.40E+04 6.25E+04 5.25E+04 6.42E+04 6.05E+04 3.61E+04 4.97E+04 5.33E+04 5.18E+03 6.75E+04 3.91E+04 4.86E+04 3.72E+03 5.88E+04 3.84E+04 4.56E+04 5.57E+03 6.08E+04 3.03E+04 5.22E+04 6.72E+03 7.06E+04 3.38E+04 5.10E+04 5.23E+03 6.53E+04 3.66E+04 1.67E+02 PASS 4.49E+04 3.89E+03 5.55E+04 3.42E+04 1.00E+02 PASS 4.94E+04 9.20E+03 7.46E+04 2.42E+04 1.00E+02 PASS 5.68E+04 8.41E+03 7.98E+04 3.37E+04 1.00E+02 PASS 0 5.41E+04 6.37E+04 6.18E+04 5.61E+04 4.91E+04 4.39E+04 5.70E+04 5.02E+04 6.52E+04 4.11E+04 5.30E+04 5.45E+04 Total 10 4.49E+04 6.33E+04 5.56E+04 4.87E+04 4.36E+04 3.89E+04 5.50E+04 5.77E+04 5.55E+04 5.38E+04 4.62E+04 5.84E+04 Dose (krad(Si)) 20 30 5.42E+04 5.75E+04 5.15E+04 5.99E+04 5.94E+04 5.20E+04 5.89E+04 4.82E+04 4.86E+04 4.90E+04 4.71E+04 4.74E+04 5.11E+04 4.74E+04 4.64E+04 4.74E+04 5.33E+04 5.89E+04 5.34E+04 5.38E+04 5.10E+04 5.19E+04 5.75E+04 6.52E+04 5.70E+04 5.91E+03 7.32E+04 4.07E+04 5.12E+04 8.21E+03 7.37E+04 2.87E+04 5.45E+04 4.68E+03 6.74E+04 4.17E+04 5.15E+04 9.81E+03 7.84E+04 2.46E+04 1.20E+03 PASS 5.22E+04 7.54E+03 7.28E+04 3.15E+04 5.00E+02 PASS 5.03E+04 3.34E+03 5.94E+04 4.11E+04 2.00E+02 PASS An ISO 9001:2008 and DSCC Certified Company 65 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Open Loop Gain 4 RL=10k VO=+/-10V (V/mV) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 6.00E+04 5.00E+04 4.00E+04 3.00E+04 2.00E+04 1.00E+04 0.00E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.30. Plot of Open Loop Gain 4 RL=10k VO=+/-10V (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 66 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.30. Raw data for Open Loop Gain 4 RL=10k VO=+/-10V (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Open Loop Gain 4 RL=10k VO=+/-10V (V/mV) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.55E+04 4.73E+04 5.58E+04 5.24E+04 4.94E+04 3.79E+04 4.60E+04 4.88E+04 4.84E+04 5.07E+04 6.13E+04 4.33E+04 24hr Anneal 60 5.04E+04 5.17E+04 5.33E+04 4.50E+04 4.86E+04 4.85E+04 4.08E+04 4.79E+04 3.76E+04 3.72E+04 4.59E+04 4.71E+04 168hr Anneal 70 5.12E+04 5.55E+04 6.07E+04 4.40E+04 5.14E+04 6.01E+04 4.59E+04 5.24E+04 4.51E+04 4.58E+04 5.46E+04 4.99E+04 4.97E+04 4.87E+03 6.30E+04 3.63E+04 5.01E+04 4.09E+03 6.13E+04 3.88E+04 4.98E+04 3.19E+03 5.86E+04 4.11E+04 5.26E+04 6.17E+03 6.95E+04 3.56E+04 4.82E+04 3.02E+03 5.65E+04 3.99E+04 1.67E+02 PASS 4.64E+04 5.02E+03 6.02E+04 3.26E+04 1.00E+02 PASS 4.24E+04 5.47E+03 5.74E+04 2.74E+04 1.00E+02 PASS 4.99E+04 6.47E+03 6.76E+04 3.21E+04 1.00E+02 PASS 0 4.91E+04 6.03E+04 5.16E+04 4.83E+04 4.93E+04 5.24E+04 5.15E+04 5.33E+04 5.73E+04 6.71E+04 6.04E+04 7.02E+04 Total 10 4.38E+04 5.61E+04 6.21E+04 5.36E+04 4.32E+04 4.43E+04 5.17E+04 4.97E+04 4.14E+04 4.40E+04 5.68E+04 4.26E+04 Dose (krad(Si)) 20 30 5.06E+04 4.78E+04 5.50E+04 5.56E+04 6.09E+04 4.37E+04 6.62E+04 4.76E+04 4.79E+04 5.37E+04 4.19E+04 4.90E+04 7.16E+04 4.50E+04 5.25E+04 5.23E+04 5.65E+04 4.54E+04 5.47E+04 4.93E+04 5.41E+04 5.67E+04 6.77E+04 5.00E+04 5.17E+04 4.95E+03 6.53E+04 3.82E+04 5.18E+04 8.16E+03 7.42E+04 2.94E+04 5.61E+04 7.50E+03 7.67E+04 3.55E+04 5.63E+04 6.41E+03 7.39E+04 3.88E+04 1.20E+03 PASS 4.62E+04 4.32E+03 5.81E+04 3.44E+04 5.00E+02 PASS 5.54E+04 1.07E+04 8.47E+04 2.62E+04 2.00E+02 PASS An ISO 9001:2008 and DSCC Certified Company 67 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Positive Output Voltage 1 @ +/-15V (V) 1.42E+01 1.40E+01 1.38E+01 1.36E+01 1.34E+01 1.32E+01 1.30E+01 1.28E+01 1.26E+01 1.24E+01 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 168hr 70 Anneal Figure 5.31. Plot of Positive Output Voltage 1 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 68 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.31. Raw data for Positive Output Voltage 1 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 1 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 24hr Anneal 60 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 168hr Anneal 70 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.09E-02 1.41E+01 1.40E+01 1.41E+01 1.06E-02 1.41E+01 1.40E+01 1.41E+01 1.02E-02 1.41E+01 1.40E+01 1.41E+01 1.01E-02 1.41E+01 1.40E+01 1.41E+01 6.39E-03 1.41E+01 1.40E+01 1.25E+01 PASS 1.41E+01 6.32E-03 1.41E+01 1.40E+01 1.25E+01 PASS 1.41E+01 6.10E-03 1.41E+01 1.40E+01 1.25E+01 PASS 1.41E+01 6.67E-03 1.41E+01 1.40E+01 1.25E+01 PASS 0 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 Total 10 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 Dose (krad(Si)) 20 30 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.03E-02 1.41E+01 1.40E+01 1.41E+01 1.00E-02 1.41E+01 1.40E+01 1.41E+01 1.00E-02 1.41E+01 1.40E+01 1.41E+01 6.23E-03 1.41E+01 1.40E+01 1.25E+01 PASS 1.41E+01 6.23E-03 1.41E+01 1.40E+01 1.25E+01 PASS 1.41E+01 7.01E-03 1.41E+01 1.40E+01 1.25E+01 PASS An ISO 9001:2008 and DSCC Certified Company 69 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Positive Output Voltage 2 @ +/-15V (V) 1.42E+01 1.40E+01 1.38E+01 1.36E+01 1.34E+01 1.32E+01 1.30E+01 1.28E+01 1.26E+01 1.24E+01 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.32. Plot of Positive Output Voltage 2 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 70 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.32. Raw data for Positive Output Voltage 2 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 2 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 24hr Anneal 60 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 168hr Anneal 70 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 8.17E-03 1.41E+01 1.41E+01 1.41E+01 7.89E-03 1.41E+01 1.41E+01 1.41E+01 8.47E-03 1.41E+01 1.41E+01 1.41E+01 8.41E-03 1.41E+01 1.40E+01 1.41E+01 6.40E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.78E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.07E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.00E-03 1.41E+01 1.41E+01 1.25E+01 PASS 0 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 Total 10 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 Dose (krad(Si)) 20 30 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 7.73E-03 1.41E+01 1.41E+01 1.41E+01 8.32E-03 1.41E+01 1.41E+01 1.41E+01 7.73E-03 1.41E+01 1.41E+01 1.41E+01 5.90E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.00E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.14E-03 1.41E+01 1.41E+01 1.25E+01 PASS An ISO 9001:2008 and DSCC Certified Company 71 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Positive Output Voltage 3 @ +/-15V (V) 1.42E+01 1.40E+01 1.38E+01 1.36E+01 1.34E+01 1.32E+01 1.30E+01 1.28E+01 1.26E+01 1.24E+01 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.33. Plot of Positive Output Voltage 3 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 72 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.33. Raw data for Positive Output Voltage 3 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 3 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 24hr Anneal 60 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 168hr Anneal 70 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 8.46E-03 1.41E+01 1.40E+01 1.41E+01 8.62E-03 1.41E+01 1.40E+01 1.41E+01 7.92E-03 1.41E+01 1.40E+01 1.41E+01 8.17E-03 1.41E+01 1.40E+01 1.41E+01 6.53E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.58E-03 1.41E+01 1.40E+01 1.25E+01 PASS 1.41E+01 6.46E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 5.93E-03 1.41E+01 1.40E+01 1.25E+01 PASS 0 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 Total 10 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 Dose (krad(Si)) 20 30 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 7.92E-03 1.41E+01 1.40E+01 1.41E+01 8.17E-03 1.41E+01 1.40E+01 1.41E+01 8.17E-03 1.41E+01 1.40E+01 1.41E+01 6.06E-03 1.41E+01 1.40E+01 1.25E+01 PASS 1.41E+01 6.14E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.28E-03 1.41E+01 1.41E+01 1.25E+01 PASS An ISO 9001:2008 and DSCC Certified Company 73 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Positive Output Voltage 4 @ +/-15V (V) 1.42E+01 1.40E+01 1.38E+01 1.36E+01 1.34E+01 1.32E+01 1.30E+01 1.28E+01 1.26E+01 1.24E+01 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.34. Plot of Positive Output Voltage 4 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 74 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.34. Raw data for Positive Output Voltage 4 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 4 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 24hr Anneal 60 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 168hr Anneal 70 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.00E-02 1.41E+01 1.40E+01 1.41E+01 9.86E-03 1.41E+01 1.40E+01 1.41E+01 9.77E-03 1.41E+01 1.40E+01 1.41E+01 9.73E-03 1.41E+01 1.40E+01 1.41E+01 6.10E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.07E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 5.97E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.24E-03 1.41E+01 1.41E+01 1.25E+01 PASS 0 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 Total 10 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 Dose (krad(Si)) 20 30 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 9.67E-03 1.41E+01 1.40E+01 1.41E+01 1.03E-02 1.41E+01 1.40E+01 1.41E+01 9.85E-03 1.41E+01 1.40E+01 1.41E+01 6.35E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.35E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.78E-03 1.41E+01 1.41E+01 1.25E+01 PASS An ISO 9001:2008 and DSCC Certified Company 75 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Negative Output Voltage 1 @ +/-15V (V) -1.20E+01 -1.25E+01 -1.30E+01 -1.35E+01 -1.40E+01 -1.45E+01 -1.50E+01 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.35. Plot of Negative Output Voltage 1 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 76 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.35. Raw data for Negative Output Voltage 1 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Output Voltage 1 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 Total Dose (krad(Si)) 10 20 30 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 50 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 24hr Anneal 60 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 168hr Anneal 70 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 5.22E-03 4.88E-03 5.22E-03 5.31E-03 5.41E-03 4.72E-03 4.69E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 3.21E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.21E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.32E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.83E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS An ISO 9001:2008 and DSCC Certified Company 77 -1.44E+01 3.83E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.51E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.29E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Negative Output Voltage 2 @ +/-15V (V) -1.20E+01 -1.25E+01 -1.30E+01 -1.35E+01 -1.40E+01 -1.45E+01 -1.50E+01 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.36. Plot of Negative Output Voltage 2 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 78 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.36. Raw data for Negative Output Voltage 2 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Output Voltage 2 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 Total Dose (krad(Si)) 10 20 30 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 50 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 24hr Anneal 60 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 168hr Anneal 70 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 3.27E-03 3.13E-03 3.42E-03 2.97E-03 2.61E-03 3.03E-03 2.92E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 2.61E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.30E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.70E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.19E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS An ISO 9001:2008 and DSCC Certified Company 79 -1.44E+01 2.61E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.45E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.45E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Negative Output Voltage 3 @ +/-15V (V) -1.20E+01 -1.25E+01 -1.30E+01 -1.35E+01 -1.40E+01 -1.45E+01 -1.50E+01 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.37. Plot of Negative Output Voltage 3 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 80 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.37. Raw data for Negative Output Voltage 3 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Output Voltage 3 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 Total Dose (krad(Si)) 10 20 30 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 50 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 24hr Anneal 60 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 168hr Anneal 70 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 2.28E-03 1.82E-03 2.28E-03 2.77E-03 2.70E-03 2.45E-03 2.30E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 2.61E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.39E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.30E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.70E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS An ISO 9001:2008 and DSCC Certified Company 81 -1.44E+01 3.16E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.45E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.92E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Negative Output Voltage 4 @ +/-15V (V) -1.20E+01 -1.25E+01 -1.30E+01 -1.35E+01 -1.40E+01 -1.45E+01 -1.50E+01 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.38. Plot of Negative Output Voltage 4 @ +/-15V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 82 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.38. Raw data for Negative Output Voltage 4 @ +/-15V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Output Voltage 4 @ +/-15V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 Total Dose (krad(Si)) 10 20 30 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 50 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 24hr Anneal 60 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 168hr Anneal 70 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 6.16E-03 5.63E-03 5.59E-03 6.07E-03 5.94E-03 5.55E-03 5.59E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 2.86E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.36E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.35E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.35E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS An ISO 9001:2008 and DSCC Certified Company 83 -1.44E+01 3.35E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.32E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 3.35E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Positive Slew Rate 1 @ +/-15V (V/us) 5.00E-01 4.50E-01 4.00E-01 3.50E-01 3.00E-01 2.50E-01 2.00E-01 1.50E-01 1.00E-01 5.00E-02 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.39. Plot of Positive Slew Rate 1 @ +/-15V (V/us) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 84 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.39. Raw data for Positive Slew Rate 1 @ +/-15V (V/us) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Slew Rate 1 @ +/-15V (V/us) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.19E-01 4.30E-01 4.62E-01 4.26E-01 4.27E-01 4.20E-01 4.30E-01 4.42E-01 4.20E-01 4.42E-01 4.42E-01 4.39E-01 24hr Anneal 60 4.13E-01 4.31E-01 4.55E-01 4.29E-01 4.28E-01 4.23E-01 4.26E-01 4.41E-01 4.20E-01 4.44E-01 4.45E-01 4.48E-01 168hr Anneal 70 4.19E-01 4.24E-01 4.58E-01 4.24E-01 4.20E-01 4.30E-01 4.30E-01 4.45E-01 4.17E-01 4.53E-01 4.47E-01 4.38E-01 4.47E-01 1.66E-02 4.92E-01 4.01E-01 4.33E-01 1.68E-02 4.79E-01 3.87E-01 4.31E-01 1.51E-02 4.73E-01 3.90E-01 4.29E-01 1.64E-02 4.74E-01 3.84E-01 4.41E-01 9.73E-03 4.67E-01 4.14E-01 1.17E-01 PASS 4.31E-01 1.10E-02 4.61E-01 4.01E-01 1.10E-01 PASS 4.31E-01 1.09E-02 4.61E-01 4.01E-01 1.10E-01 PASS 4.35E-01 1.41E-02 4.74E-01 3.96E-01 1.10E-01 PASS 0 4.32E-01 4.48E-01 4.77E-01 4.47E-01 4.44E-01 4.41E-01 4.49E-01 4.59E-01 4.37E-01 4.61E-01 4.40E-01 4.40E-01 Total 10 4.33E-01 4.42E-01 4.75E-01 4.43E-01 4.41E-01 4.37E-01 4.45E-01 4.65E-01 4.41E-01 4.74E-01 4.42E-01 4.41E-01 Dose (krad(Si)) 20 30 4.32E-01 4.32E-01 4.41E-01 4.46E-01 4.71E-01 4.75E-01 4.39E-01 4.40E-01 4.50E-01 4.40E-01 4.44E-01 4.28E-01 4.44E-01 4.36E-01 4.54E-01 4.50E-01 4.31E-01 4.39E-01 4.65E-01 4.51E-01 4.41E-01 4.49E-01 4.41E-01 4.42E-01 4.50E-01 1.66E-02 4.95E-01 4.04E-01 4.47E-01 1.63E-02 4.91E-01 4.02E-01 4.47E-01 1.51E-02 4.88E-01 4.05E-01 4.49E-01 1.06E-02 4.79E-01 4.20E-01 2.00E-01 PASS 4.52E-01 1.62E-02 4.97E-01 4.08E-01 1.30E-01 PASS 4.48E-01 1.27E-02 4.82E-01 4.13E-01 1.20E-01 PASS An ISO 9001:2008 and DSCC Certified Company 85 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Positive Slew Rate 2 @ +/-15V (V/us) 6.00E-01 5.00E-01 4.00E-01 3.00E-01 2.00E-01 1.00E-01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.40. Plot of Positive Slew Rate 2 @ +/-15V (V/us) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 86 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.40. Raw data for Positive Slew Rate 2 @ +/-15V (V/us) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Slew Rate 2 @ +/-15V (V/us) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.49E-01 4.84E-01 4.78E-01 4.73E-01 4.59E-01 4.43E-01 4.60E-01 4.59E-01 4.82E-01 4.52E-01 4.73E-01 5.13E-01 24hr Anneal 60 4.43E-01 4.74E-01 4.69E-01 4.64E-01 4.63E-01 4.46E-01 4.68E-01 4.57E-01 4.80E-01 4.44E-01 4.88E-01 5.11E-01 168hr Anneal 70 4.39E-01 4.75E-01 4.75E-01 4.74E-01 4.54E-01 4.49E-01 4.69E-01 4.67E-01 4.82E-01 4.56E-01 4.83E-01 4.98E-01 4.83E-01 1.45E-02 5.23E-01 4.43E-01 4.69E-01 1.43E-02 5.08E-01 4.29E-01 4.63E-01 1.18E-02 4.95E-01 4.30E-01 4.63E-01 1.63E-02 5.08E-01 4.19E-01 4.73E-01 1.97E-02 5.27E-01 4.19E-01 1.17E-01 PASS 4.59E-01 1.44E-02 4.99E-01 4.20E-01 1.10E-01 PASS 4.59E-01 1.52E-02 5.01E-01 4.17E-01 1.10E-01 PASS 4.65E-01 1.27E-02 4.99E-01 4.30E-01 1.10E-01 PASS 0 4.77E-01 4.97E-01 4.91E-01 4.85E-01 4.90E-01 4.56E-01 4.80E-01 4.76E-01 4.94E-01 4.69E-01 4.80E-01 5.05E-01 Total 10 4.68E-01 5.02E-01 4.88E-01 4.88E-01 4.76E-01 4.57E-01 4.88E-01 4.87E-01 5.13E-01 4.76E-01 4.90E-01 5.19E-01 Dose (krad(Si)) 20 30 4.58E-01 4.58E-01 4.90E-01 4.90E-01 4.92E-01 4.95E-01 4.90E-01 4.88E-01 4.78E-01 4.85E-01 4.55E-01 4.51E-01 4.76E-01 4.80E-01 4.77E-01 4.75E-01 5.05E-01 5.01E-01 4.73E-01 4.58E-01 4.90E-01 4.87E-01 5.11E-01 5.04E-01 4.88E-01 7.48E-03 5.09E-01 4.67E-01 4.84E-01 1.30E-02 5.20E-01 4.49E-01 4.82E-01 1.43E-02 5.21E-01 4.42E-01 4.75E-01 1.40E-02 5.13E-01 4.37E-01 2.00E-01 PASS 4.84E-01 2.04E-02 5.40E-01 4.28E-01 1.30E-01 PASS 4.77E-01 1.79E-02 5.26E-01 4.28E-01 1.20E-01 PASS An ISO 9001:2008 and DSCC Certified Company 87 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Positive Slew Rate 3 @ +/-15V (V/us) 5.00E-01 4.50E-01 4.00E-01 3.50E-01 3.00E-01 2.50E-01 2.00E-01 1.50E-01 1.00E-01 5.00E-02 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.41. Plot of Positive Slew Rate 3 @ +/-15V (V/us) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 88 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.41. Raw data for Positive Slew Rate 3 @ +/-15V (V/us) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Slew Rate 3 @ +/-15V (V/us) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.23E-01 4.56E-01 4.48E-01 4.48E-01 4.37E-01 4.13E-01 4.42E-01 4.39E-01 4.59E-01 4.25E-01 4.55E-01 4.90E-01 24hr Anneal 60 4.24E-01 4.55E-01 4.47E-01 4.41E-01 4.31E-01 4.17E-01 4.39E-01 4.41E-01 4.66E-01 4.30E-01 4.67E-01 4.83E-01 168hr Anneal 70 4.21E-01 4.46E-01 4.37E-01 4.37E-01 4.34E-01 4.23E-01 4.43E-01 4.42E-01 4.58E-01 4.29E-01 4.59E-01 4.81E-01 4.51E-01 1.18E-02 4.83E-01 4.18E-01 4.42E-01 1.28E-02 4.77E-01 4.07E-01 4.40E-01 1.24E-02 4.73E-01 4.06E-01 4.35E-01 9.03E-03 4.60E-01 4.10E-01 4.46E-01 1.64E-02 4.91E-01 4.01E-01 1.17E-01 PASS 4.36E-01 1.75E-02 4.84E-01 3.88E-01 1.10E-01 PASS 4.39E-01 1.80E-02 4.88E-01 3.89E-01 1.10E-01 PASS 4.39E-01 1.36E-02 4.76E-01 4.02E-01 1.10E-01 PASS 0 4.38E-01 4.67E-01 4.61E-01 4.66E-01 4.54E-01 4.33E-01 4.50E-01 4.53E-01 4.77E-01 4.40E-01 4.55E-01 4.77E-01 Total 10 4.36E-01 4.74E-01 4.64E-01 4.66E-01 4.54E-01 4.29E-01 4.58E-01 4.60E-01 4.71E-01 4.54E-01 4.64E-01 4.94E-01 Dose (krad(Si)) 20 30 4.35E-01 4.33E-01 4.68E-01 4.61E-01 4.66E-01 4.49E-01 4.72E-01 4.62E-01 4.59E-01 4.48E-01 4.27E-01 4.24E-01 4.59E-01 4.49E-01 4.54E-01 4.56E-01 4.73E-01 4.66E-01 4.39E-01 4.37E-01 4.62E-01 4.57E-01 4.86E-01 4.79E-01 4.57E-01 1.19E-02 4.90E-01 4.25E-01 4.59E-01 1.46E-02 4.99E-01 4.19E-01 4.60E-01 1.47E-02 5.00E-01 4.20E-01 4.51E-01 1.68E-02 4.97E-01 4.05E-01 2.00E-01 PASS 4.54E-01 1.55E-02 4.97E-01 4.12E-01 1.30E-01 PASS 4.50E-01 1.79E-02 4.99E-01 4.01E-01 1.20E-01 PASS An ISO 9001:2008 and DSCC Certified Company 89 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Positive Slew Rate 4 @ +/-15V (V/us) 6.00E-01 5.00E-01 4.00E-01 3.00E-01 2.00E-01 1.00E-01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.42. Plot of Positive Slew Rate 4 @ +/-15V (V/us) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 90 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.42. Raw data for Positive Slew Rate 4 @ +/-15V (V/us) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Slew Rate 4 @ +/-15V (V/us) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.47E-01 4.56E-01 5.01E-01 4.47E-01 4.63E-01 4.46E-01 4.49E-01 4.73E-01 4.57E-01 4.74E-01 4.69E-01 4.66E-01 24hr Anneal 60 4.47E-01 4.57E-01 4.93E-01 4.55E-01 4.54E-01 4.38E-01 4.55E-01 4.82E-01 4.54E-01 4.73E-01 4.73E-01 4.74E-01 168hr Anneal 70 4.35E-01 4.48E-01 4.83E-01 4.47E-01 4.45E-01 4.57E-01 4.56E-01 4.76E-01 4.53E-01 4.77E-01 4.78E-01 4.79E-01 4.71E-01 1.73E-02 5.18E-01 4.23E-01 4.63E-01 2.24E-02 5.24E-01 4.01E-01 4.61E-01 1.82E-02 5.11E-01 4.11E-01 4.52E-01 1.83E-02 5.02E-01 4.01E-01 4.69E-01 1.34E-02 5.06E-01 4.32E-01 1.17E-01 PASS 4.60E-01 1.31E-02 4.96E-01 4.24E-01 1.10E-01 PASS 4.60E-01 1.73E-02 5.08E-01 4.13E-01 1.10E-01 PASS 4.64E-01 1.17E-02 4.96E-01 4.32E-01 1.10E-01 PASS 0 4.72E-01 4.68E-01 5.11E-01 4.68E-01 4.86E-01 4.61E-01 4.60E-01 4.93E-01 4.61E-01 4.82E-01 4.67E-01 4.67E-01 Total 10 4.67E-01 4.61E-01 5.10E-01 4.63E-01 4.77E-01 4.68E-01 4.75E-01 4.93E-01 4.66E-01 5.01E-01 4.73E-01 4.62E-01 Dose (krad(Si)) 20 30 4.68E-01 4.60E-01 4.70E-01 4.61E-01 4.98E-01 4.99E-01 4.66E-01 4.58E-01 4.75E-01 4.76E-01 4.61E-01 4.60E-01 4.72E-01 4.59E-01 4.96E-01 4.78E-01 4.68E-01 4.59E-01 4.91E-01 4.88E-01 4.72E-01 4.68E-01 4.67E-01 4.71E-01 4.81E-01 1.83E-02 5.31E-01 4.31E-01 4.76E-01 2.02E-02 5.31E-01 4.20E-01 4.75E-01 1.31E-02 5.11E-01 4.40E-01 4.71E-01 1.52E-02 5.13E-01 4.30E-01 2.00E-01 PASS 4.81E-01 1.56E-02 5.23E-01 4.38E-01 1.30E-01 PASS 4.78E-01 1.51E-02 5.19E-01 4.36E-01 1.20E-01 PASS An ISO 9001:2008 and DSCC Certified Company 91 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Negative Slew Rate 1 @ +/-15V (V/us) 0.00E+00 -1.00E-01 -2.00E-01 -3.00E-01 -4.00E-01 -5.00E-01 -6.00E-01 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.43. Plot of Negative Slew Rate 1 @ +/-15V (V/us) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 92 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.43. Raw data for Negative Slew Rate 1 @ +/-15V (V/us) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Slew Rate 1 @ +/-15V (V/us) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 -4.78E-01 -4.77E-01 -5.19E-01 -4.77E-01 -4.80E-01 -4.66E-01 -4.73E-01 -5.05E-01 -4.75E-01 -5.09E-01 -4.97E-01 -4.88E-01 24hr Anneal 60 -4.60E-01 -4.93E-01 -5.10E-01 -4.80E-01 -4.72E-01 -4.66E-01 -4.79E-01 -4.91E-01 -4.67E-01 -4.89E-01 -4.96E-01 -4.89E-01 168hr Anneal 70 -4.72E-01 -4.73E-01 -5.10E-01 -4.62E-01 -4.85E-01 -4.79E-01 -4.95E-01 -5.08E-01 -4.69E-01 -4.94E-01 -4.91E-01 -4.94E-01 -4.96E-01 2.11E-02 -4.38E-01 -5.53E-01 -4.86E-01 1.84E-02 -4.36E-01 -5.37E-01 -4.83E-01 1.93E-02 -4.30E-01 -5.36E-01 -4.80E-01 1.84E-02 -4.30E-01 -5.31E-01 -4.96E-01 1.87E-02 -4.44E-01 -5.47E-01 -1.17E-01 PASS -4.86E-01 1.99E-02 -4.31E-01 -5.40E-01 -1.10E-01 PASS -4.78E-01 1.18E-02 -4.46E-01 -5.11E-01 -1.10E-01 PASS -4.89E-01 1.52E-02 -4.47E-01 -5.31E-01 -1.10E-01 PASS 0 -4.85E-01 -5.03E-01 -5.40E-01 -5.12E-01 -4.99E-01 -4.75E-01 -4.95E-01 -5.07E-01 -4.91E-01 -5.12E-01 -4.97E-01 -4.98E-01 Total 10 -4.73E-01 -4.98E-01 -5.30E-01 -4.89E-01 -5.07E-01 -4.97E-01 -4.99E-01 -5.22E-01 -4.96E-01 -5.21E-01 -4.88E-01 -4.91E-01 Dose (krad(Si)) 20 30 -4.84E-01 -4.69E-01 -4.90E-01 -4.96E-01 -5.37E-01 -5.27E-01 -4.88E-01 -4.99E-01 -4.94E-01 -4.87E-01 -4.93E-01 -4.88E-01 -4.92E-01 -4.84E-01 -5.03E-01 -5.09E-01 -4.82E-01 -4.76E-01 -5.19E-01 -5.21E-01 -4.95E-01 -4.92E-01 -4.92E-01 -5.05E-01 -5.08E-01 2.05E-02 -4.52E-01 -5.64E-01 -4.99E-01 2.12E-02 -4.41E-01 -5.58E-01 -4.99E-01 2.18E-02 -4.39E-01 -5.58E-01 -4.96E-01 1.45E-02 -4.56E-01 -5.36E-01 -2.00E-01 PASS -5.07E-01 1.33E-02 -4.71E-01 -5.43E-01 -1.30E-01 PASS -4.98E-01 1.40E-02 -4.59E-01 -5.36E-01 -1.20E-01 PASS An ISO 9001:2008 and DSCC Certified Company 93 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Negative Slew Rate 2 @ +/-15V (V/us) 0.00E+00 -1.00E-01 -2.00E-01 -3.00E-01 -4.00E-01 -5.00E-01 -6.00E-01 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.44. Plot of Negative Slew Rate 2 @ +/-15V (V/us) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 94 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.44. Raw data for Negative Slew Rate 2 @ +/-15V (V/us) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Slew Rate 2 @ +/-15V (V/us) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 -5.15E-01 -5.47E-01 -5.40E-01 -5.19E-01 -5.23E-01 -4.99E-01 -5.16E-01 -5.17E-01 -5.39E-01 -5.02E-01 -5.46E-01 -5.57E-01 24hr Anneal 60 -4.88E-01 -5.38E-01 -5.30E-01 -5.24E-01 -5.16E-01 -4.78E-01 -5.24E-01 -5.20E-01 -5.41E-01 -4.99E-01 -5.35E-01 -5.66E-01 168hr Anneal 70 -4.86E-01 -5.22E-01 -5.34E-01 -5.21E-01 -5.14E-01 -4.89E-01 -5.33E-01 -5.21E-01 -5.42E-01 -5.14E-01 -5.38E-01 -5.66E-01 -5.34E-01 1.07E-02 -5.05E-01 -5.64E-01 -5.29E-01 1.39E-02 -4.91E-01 -5.67E-01 -5.19E-01 1.92E-02 -4.67E-01 -5.72E-01 -5.15E-01 1.79E-02 -4.66E-01 -5.65E-01 -5.30E-01 1.95E-02 -4.76E-01 -5.84E-01 -1.17E-01 PASS -5.15E-01 1.59E-02 -4.71E-01 -5.58E-01 -1.10E-01 PASS -5.12E-01 2.44E-02 -4.46E-01 -5.79E-01 -1.10E-01 PASS -5.20E-01 2.03E-02 -4.64E-01 -5.76E-01 -1.10E-01 PASS 0 -5.27E-01 -5.46E-01 -5.52E-01 -5.55E-01 -5.40E-01 -5.13E-01 -5.33E-01 -5.23E-01 -5.66E-01 -5.24E-01 -5.44E-01 -5.57E-01 Total 10 -5.07E-01 -5.41E-01 -5.38E-01 -5.50E-01 -5.31E-01 -5.16E-01 -5.37E-01 -5.31E-01 -5.59E-01 -5.29E-01 -5.44E-01 -5.62E-01 Dose (krad(Si)) 20 30 -5.30E-01 -5.20E-01 -5.38E-01 -5.32E-01 -5.54E-01 -5.31E-01 -5.47E-01 -5.49E-01 -5.41E-01 -5.39E-01 -5.23E-01 -5.10E-01 -5.33E-01 -5.56E-01 -5.45E-01 -5.35E-01 -5.46E-01 -5.38E-01 -5.29E-01 -5.11E-01 -5.40E-01 -5.45E-01 -5.64E-01 -5.65E-01 -5.44E-01 1.11E-02 -5.14E-01 -5.74E-01 -5.33E-01 1.63E-02 -4.89E-01 -5.78E-01 -5.42E-01 9.08E-03 -5.17E-01 -5.67E-01 -5.32E-01 2.04E-02 -4.76E-01 -5.88E-01 -2.00E-01 PASS -5.34E-01 1.57E-02 -4.91E-01 -5.78E-01 -1.30E-01 PASS -5.35E-01 1.01E-02 -5.08E-01 -5.63E-01 -1.20E-01 PASS An ISO 9001:2008 and DSCC Certified Company 95 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Negative Slew Rate 3 @ +/-15V (V/us) 0.00E+00 -1.00E-01 -2.00E-01 -3.00E-01 -4.00E-01 -5.00E-01 -6.00E-01 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.45. Plot of Negative Slew Rate 3 @ +/-15V (V/us) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 96 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.45. Raw data for Negative Slew Rate 3 @ +/-15V (V/us) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Slew Rate 3 @ +/-15V (V/us) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 -4.82E-01 -5.10E-01 -4.96E-01 -5.07E-01 -4.89E-01 -4.70E-01 -4.93E-01 -4.95E-01 -5.02E-01 -4.76E-01 -5.12E-01 -5.26E-01 24hr Anneal 60 -4.63E-01 -5.01E-01 -4.89E-01 -4.91E-01 -4.88E-01 -4.63E-01 -4.83E-01 -4.91E-01 -5.18E-01 -4.74E-01 -5.15E-01 -5.36E-01 168hr Anneal 70 -4.67E-01 -5.04E-01 -4.93E-01 -4.94E-01 -4.89E-01 -4.83E-01 -5.08E-01 -4.97E-01 -5.13E-01 -4.79E-01 -4.99E-01 -5.40E-01 -5.01E-01 1.11E-02 -4.71E-01 -5.32E-01 -4.97E-01 1.18E-02 -4.64E-01 -5.29E-01 -4.86E-01 1.41E-02 -4.48E-01 -5.25E-01 -4.89E-01 1.37E-02 -4.52E-01 -5.27E-01 -4.98E-01 1.41E-02 -4.59E-01 -5.36E-01 -1.17E-01 PASS -4.87E-01 1.36E-02 -4.50E-01 -5.24E-01 -1.10E-01 PASS -4.86E-01 2.08E-02 -4.29E-01 -5.43E-01 -1.10E-01 PASS -4.96E-01 1.49E-02 -4.55E-01 -5.37E-01 -1.10E-01 PASS 0 -4.85E-01 -5.26E-01 -5.20E-01 -5.09E-01 -5.21E-01 -4.77E-01 -4.97E-01 -5.06E-01 -5.35E-01 -4.90E-01 -5.06E-01 -5.26E-01 Total 10 -4.80E-01 -5.33E-01 -5.10E-01 -5.24E-01 -5.10E-01 -4.85E-01 -5.12E-01 -5.04E-01 -5.37E-01 -4.97E-01 -5.17E-01 -5.37E-01 Dose (krad(Si)) 20 30 -4.87E-01 -4.85E-01 -5.25E-01 -5.09E-01 -5.07E-01 -4.96E-01 -5.11E-01 -5.13E-01 -4.95E-01 -5.04E-01 -4.76E-01 -4.79E-01 -5.03E-01 -5.02E-01 -5.15E-01 -5.00E-01 -5.37E-01 -5.17E-01 -4.90E-01 -4.91E-01 -5.10E-01 -5.10E-01 -5.43E-01 -5.29E-01 -5.12E-01 1.64E-02 -4.67E-01 -5.57E-01 -5.11E-01 2.01E-02 -4.56E-01 -5.66E-01 -5.05E-01 1.47E-02 -4.65E-01 -5.45E-01 -5.01E-01 2.18E-02 -4.41E-01 -5.61E-01 -2.00E-01 PASS -5.07E-01 1.95E-02 -4.54E-01 -5.60E-01 -1.30E-01 PASS -5.04E-01 2.34E-02 -4.40E-01 -5.68E-01 -1.20E-01 PASS An ISO 9001:2008 and DSCC Certified Company 97 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Negative Slew Rate 4 @ +/-15V (V/us) 0.00E+00 -1.00E-01 -2.00E-01 -3.00E-01 -4.00E-01 -5.00E-01 -6.00E-01 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.46. Plot of Negative Slew Rate 4 @ +/-15V (V/us) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 98 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.46. Raw data for Negative Slew Rate 4 @ +/-15V (V/us) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Slew Rate 4 @ +/-15V (V/us) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 -4.99E-01 -5.12E-01 -5.44E-01 -5.05E-01 -5.09E-01 -5.06E-01 -5.11E-01 -5.49E-01 -5.09E-01 -5.22E-01 -5.34E-01 -5.25E-01 24hr Anneal 60 -4.98E-01 -5.04E-01 -5.54E-01 -5.18E-01 -5.10E-01 -5.08E-01 -5.00E-01 -5.43E-01 -5.03E-01 -5.31E-01 -5.11E-01 -5.17E-01 168hr Anneal 70 -5.09E-01 -5.01E-01 -5.42E-01 -4.98E-01 -5.10E-01 -4.96E-01 -5.12E-01 -5.25E-01 -5.05E-01 -5.50E-01 -5.22E-01 -5.39E-01 -5.34E-01 1.84E-02 -4.84E-01 -5.85E-01 -5.14E-01 1.76E-02 -4.66E-01 -5.62E-01 -5.17E-01 2.21E-02 -4.56E-01 -5.77E-01 -5.12E-01 1.75E-02 -4.64E-01 -5.60E-01 -5.24E-01 1.74E-02 -4.77E-01 -5.72E-01 -1.17E-01 PASS -5.19E-01 1.76E-02 -4.71E-01 -5.68E-01 -1.10E-01 PASS -5.17E-01 1.90E-02 -4.65E-01 -5.69E-01 -1.10E-01 PASS -5.18E-01 2.10E-02 -4.60E-01 -5.75E-01 -1.10E-01 PASS 0 -5.12E-01 -5.34E-01 -5.63E-01 -5.15E-01 -5.39E-01 -5.20E-01 -5.34E-01 -5.53E-01 -5.20E-01 -5.39E-01 -5.33E-01 -5.28E-01 Total 10 -5.14E-01 -5.16E-01 -5.74E-01 -5.25E-01 -5.39E-01 -5.39E-01 -5.43E-01 -5.46E-01 -5.24E-01 -5.49E-01 -5.39E-01 -5.28E-01 Dose (krad(Si)) 20 30 -5.16E-01 -5.14E-01 -5.26E-01 -5.39E-01 -5.67E-01 -5.61E-01 -5.28E-01 -5.20E-01 -5.32E-01 -5.37E-01 -5.14E-01 -5.16E-01 -5.31E-01 -5.09E-01 -5.45E-01 -5.42E-01 -5.18E-01 -5.10E-01 -5.45E-01 -5.44E-01 -5.25E-01 -5.19E-01 -5.27E-01 -5.17E-01 -5.33E-01 2.06E-02 -4.76E-01 -5.89E-01 -5.34E-01 2.46E-02 -4.66E-01 -6.01E-01 -5.34E-01 1.95E-02 -4.80E-01 -5.87E-01 -5.33E-01 1.39E-02 -4.95E-01 -5.71E-01 -2.00E-01 PASS -5.40E-01 9.78E-03 -5.13E-01 -5.67E-01 -1.30E-01 PASS -5.31E-01 1.46E-02 -4.91E-01 -5.71E-01 -1.20E-01 PASS An ISO 9001:2008 and DSCC Certified Company 99 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Positive Supply Current @ +5V (A) 2.50E-03 2.00E-03 1.50E-03 1.00E-03 5.00E-04 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.47. Plot of Positive Supply Current @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 100 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.47. Raw data for Positive Supply Current @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Supply Current @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 1.31E-03 1.33E-03 1.36E-03 1.30E-03 1.33E-03 1.34E-03 1.31E-03 1.34E-03 1.33E-03 1.31E-03 1.32E-03 1.34E-03 24hr Anneal 60 1.28E-03 1.29E-03 1.31E-03 1.25E-03 1.30E-03 1.32E-03 1.28E-03 1.32E-03 1.30E-03 1.29E-03 1.32E-03 1.34E-03 168hr Anneal 70 1.23E-03 1.23E-03 1.25E-03 1.20E-03 1.23E-03 1.30E-03 1.26E-03 1.29E-03 1.28E-03 1.26E-03 1.33E-03 1.34E-03 1.38E-03 2.20E-05 1.44E-03 1.32E-03 1.32E-03 2.35E-05 1.39E-03 1.26E-03 1.28E-03 2.10E-05 1.34E-03 1.23E-03 1.23E-03 1.69E-05 1.27E-03 1.18E-03 1.36E-03 1.85E-05 1.41E-03 1.31E-03 2.00E-03 PASS 1.32E-03 1.58E-05 1.37E-03 1.28E-03 2.00E-03 PASS 1.30E-03 1.60E-05 1.34E-03 1.25E-03 2.00E-03 PASS 1.28E-03 1.74E-05 1.32E-03 1.23E-03 2.00E-03 PASS 0 1.37E-03 1.38E-03 1.37E-03 1.32E-03 1.40E-03 1.33E-03 1.30E-03 1.33E-03 1.32E-03 1.29E-03 1.32E-03 1.34E-03 Total 10 1.35E-03 1.36E-03 1.39E-03 1.35E-03 1.36E-03 1.42E-03 1.38E-03 1.41E-03 1.39E-03 1.39E-03 1.33E-03 1.34E-03 Dose (krad(Si)) 20 30 1.38E-03 1.37E-03 1.39E-03 1.37E-03 1.42E-03 1.41E-03 1.37E-03 1.35E-03 1.39E-03 1.39E-03 1.40E-03 1.39E-03 1.37E-03 1.35E-03 1.40E-03 1.38E-03 1.38E-03 1.37E-03 1.38E-03 1.35E-03 1.32E-03 1.32E-03 1.34E-03 1.34E-03 1.37E-03 2.86E-05 1.45E-03 1.29E-03 1.36E-03 1.62E-05 1.41E-03 1.32E-03 1.39E-03 1.94E-05 1.44E-03 1.34E-03 1.31E-03 1.74E-05 1.36E-03 1.27E-03 2.00E-03 PASS 1.40E-03 1.60E-05 1.44E-03 1.35E-03 2.00E-03 PASS 1.38E-03 1.51E-05 1.43E-03 1.34E-03 2.00E-03 PASS An ISO 9001:2008 and DSCC Certified Company 101 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased Negative Supply Current @ +5V (A) 0.00E+00 -5.00E-04 -1.00E-03 -1.50E-03 -2.00E-03 -2.50E-03 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.48. Plot of Negative Supply Current @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 102 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.48. Raw data for Negative Supply Current @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Supply Current @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 -1.30E-03 -1.30E-03 -1.34E-03 -1.28E-03 -1.31E-03 -1.32E-03 -1.29E-03 -1.31E-03 -1.30E-03 -1.28E-03 -1.30E-03 -1.32E-03 24hr Anneal 60 -1.26E-03 -1.27E-03 -1.29E-03 -1.23E-03 -1.28E-03 -1.30E-03 -1.27E-03 -1.29E-03 -1.28E-03 -1.26E-03 -1.30E-03 -1.32E-03 168hr Anneal 70 -1.20E-03 -1.20E-03 -1.23E-03 -1.18E-03 -1.22E-03 -1.27E-03 -1.24E-03 -1.27E-03 -1.25E-03 -1.24E-03 -1.30E-03 -1.32E-03 -1.36E-03 2.14E-05 -1.30E-03 -1.42E-03 -1.30E-03 2.22E-05 -1.24E-03 -1.37E-03 -1.27E-03 2.19E-05 -1.21E-03 -1.33E-03 -1.21E-03 1.88E-05 -1.16E-03 -1.26E-03 -1.34E-03 1.76E-05 -1.29E-03 -1.39E-03 -2.00E-03 PASS -1.30E-03 1.57E-05 -1.26E-03 -1.34E-03 -2.00E-03 PASS -1.28E-03 1.51E-05 -1.24E-03 -1.32E-03 -2.00E-03 PASS -1.26E-03 1.54E-05 -1.21E-03 -1.30E-03 -2.00E-03 PASS 0 -1.35E-03 -1.35E-03 -1.35E-03 -1.30E-03 -1.38E-03 -1.31E-03 -1.28E-03 -1.30E-03 -1.30E-03 -1.27E-03 -1.30E-03 -1.32E-03 Total 10 -1.33E-03 -1.35E-03 -1.37E-03 -1.33E-03 -1.34E-03 -1.40E-03 -1.36E-03 -1.39E-03 -1.37E-03 -1.36E-03 -1.30E-03 -1.32E-03 Dose (krad(Si)) 20 30 -1.36E-03 -1.35E-03 -1.37E-03 -1.36E-03 -1.40E-03 -1.39E-03 -1.35E-03 -1.33E-03 -1.37E-03 -1.36E-03 -1.39E-03 -1.36E-03 -1.35E-03 -1.32E-03 -1.38E-03 -1.36E-03 -1.36E-03 -1.34E-03 -1.35E-03 -1.32E-03 -1.30E-03 -1.30E-03 -1.32E-03 -1.32E-03 -1.35E-03 2.96E-05 -1.27E-03 -1.43E-03 -1.34E-03 1.74E-05 -1.30E-03 -1.39E-03 -1.37E-03 1.75E-05 -1.32E-03 -1.42E-03 -1.29E-03 1.57E-05 -1.25E-03 -1.33E-03 -2.00E-03 PASS -1.38E-03 1.60E-05 -1.33E-03 -1.42E-03 -2.00E-03 PASS -1.36E-03 1.58E-05 -1.32E-03 -1.41E-03 -2.00E-03 PASS An ISO 9001:2008 and DSCC Certified Company 103 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-03 Offset Voltage 1 @ +5V (V) 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.49. Plot of Offset Voltage 1 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 104 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.49. Raw data for Offset Voltage 1 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Voltage 1 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 5.77E-05 2.73E-05 3.02E-06 8.45E-06 -1.44E-05 8.93E-05 -6.00E-05 -4.08E-05 1.16E-04 -2.18E-05 -1.06E-04 -3.98E-05 24hr Anneal 60 6.02E-05 2.14E-05 9.61E-07 1.05E-05 -1.50E-05 7.88E-05 -6.49E-05 -4.82E-05 1.09E-04 -3.01E-05 -1.06E-04 -3.98E-05 168hr Anneal 70 3.16E-05 5.19E-06 -1.57E-05 6.15E-06 -3.84E-05 4.53E-05 -8.09E-05 -8.17E-05 7.53E-05 -4.79E-05 -1.07E-04 -4.00E-05 -7.00E-06 2.70E-05 6.69E-05 -8.10E-05 1.64E-05 2.74E-05 9.17E-05 -5.88E-05 1.56E-05 2.83E-05 9.32E-05 -6.19E-05 -2.23E-06 2.63E-05 6.98E-05 -7.43E-05 -5.46E-06 7.47E-05 1.99E-04 -2.10E-04 -6.50E-04 PASS 6.50E-04 PASS 1.66E-05 8.04E-05 2.37E-04 -2.04E-04 -7.50E-04 PASS 7.50E-04 PASS 8.88E-06 7.92E-05 2.26E-04 -2.08E-04 -7.50E-04 PASS 7.50E-04 PASS -1.80E-05 7.35E-05 1.84E-04 -2.20E-04 -7.50E-04 PASS 7.50E-04 PASS 0 1.13E-05 -1.58E-05 -1.39E-05 -1.52E-05 -5.06E-05 2.28E-05 -9.98E-05 -1.04E-04 4.38E-05 -6.58E-05 -1.06E-04 -3.88E-05 Total 10 4.34E-06 -1.07E-05 -3.65E-05 -3.30E-05 -7.04E-05 3.60E-05 -9.21E-05 -9.22E-05 5.87E-05 -5.78E-05 -1.07E-04 -3.94E-05 Dose (krad(Si)) 20 30 1.25E-05 2.85E-05 -5.32E-06 6.52E-06 -2.37E-05 -1.23E-05 -2.32E-05 -1.33E-05 -5.89E-05 -4.44E-05 4.78E-05 6.38E-05 -8.44E-05 -7.34E-05 -8.06E-05 -6.51E-05 7.14E-05 8.56E-05 -4.85E-05 -3.83E-05 -1.06E-04 -1.08E-04 -4.01E-05 -4.01E-05 -1.68E-05 2.21E-05 4.36E-05 -7.73E-05 -2.92E-05 2.84E-05 4.86E-05 -1.07E-04 -1.97E-05 2.65E-05 5.30E-05 -9.24E-05 -4.05E-05 6.94E-05 1.50E-04 -2.31E-04 -4.50E-04 PASS 4.50E-04 PASS -2.95E-05 7.20E-05 1.68E-04 -2.27E-04 -6.00E-04 PASS 6.00E-04 PASS -1.89E-05 7.35E-05 1.83E-04 -2.20E-04 -6.00E-04 PASS 6.00E-04 PASS An ISO 9001:2008 and DSCC Certified Company 105 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-03 Offset Voltage 2 @ +5V (V) 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.50. Plot of Offset Voltage 2 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 106 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.50. Raw data for Offset Voltage 2 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Voltage 2 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 1.25E-04 1.05E-05 9.96E-05 8.61E-05 7.35E-05 1.09E-04 -1.47E-05 1.45E-05 4.37E-05 1.57E-06 -1.56E-05 -3.77E-05 24hr Anneal 60 1.22E-04 1.50E-05 9.32E-05 7.92E-05 6.72E-05 9.78E-05 -2.09E-05 7.60E-06 4.15E-05 -9.06E-06 -1.56E-05 -3.73E-05 168hr Anneal 70 9.19E-05 -2.54E-06 7.64E-05 5.42E-05 4.61E-05 5.31E-05 -5.78E-05 -2.38E-05 1.68E-05 -4.47E-05 -1.58E-05 -3.85E-05 5.86E-05 3.66E-05 1.59E-04 -4.17E-05 7.89E-05 4.27E-05 1.96E-04 -3.83E-05 7.52E-05 3.93E-05 1.83E-04 -3.25E-05 5.32E-05 3.60E-05 1.52E-04 -4.56E-05 1.18E-05 4.54E-05 1.36E-04 -1.13E-04 -6.50E-04 PASS 6.50E-04 PASS 3.07E-05 4.85E-05 1.64E-04 -1.02E-04 -7.50E-04 PASS 7.50E-04 PASS 2.34E-05 4.78E-05 1.54E-04 -1.08E-04 -7.50E-04 PASS 7.50E-04 PASS -1.13E-05 4.57E-05 1.14E-04 -1.37E-04 -7.50E-04 PASS 7.50E-04 PASS 0 6.69E-05 -5.92E-06 5.27E-05 3.52E-05 3.92E-05 3.44E-05 -6.18E-05 -2.89E-05 1.38E-05 -5.06E-05 -1.64E-05 -3.88E-05 Total 10 7.53E-05 -3.87E-06 6.34E-05 4.36E-05 2.63E-05 4.82E-05 -5.15E-05 -2.04E-05 1.98E-05 -3.44E-05 -1.59E-05 -3.80E-05 Dose (krad(Si)) 20 30 8.45E-05 9.63E-05 -8.49E-07 1.08E-06 7.40E-05 8.29E-05 5.14E-05 5.97E-05 4.07E-05 5.30E-05 6.46E-05 8.01E-05 -4.18E-05 -3.52E-05 -1.26E-05 -2.66E-06 2.50E-05 3.20E-05 -2.52E-05 -1.53E-05 -1.63E-05 -1.58E-05 -3.75E-05 -3.91E-05 3.76E-05 2.73E-05 1.13E-04 -3.73E-05 4.09E-05 3.13E-05 1.27E-04 -4.48E-05 4.99E-05 3.33E-05 1.41E-04 -4.14E-05 -1.86E-05 4.14E-05 9.49E-05 -1.32E-04 -4.50E-04 PASS 4.50E-04 PASS -7.68E-06 4.08E-05 1.04E-04 -1.20E-04 -6.00E-04 PASS 6.00E-04 PASS 2.00E-06 4.28E-05 1.19E-04 -1.15E-04 -6.00E-04 PASS 6.00E-04 PASS An ISO 9001:2008 and DSCC Certified Company 107 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-03 Offset Voltage 3 @ +5V (V) 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.51. Plot of Offset Voltage 3 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 108 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.51. Raw data for Offset Voltage 3 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Voltage 3 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 2.09E-05 -7.71E-05 1.93E-06 -3.24E-05 9.29E-06 7.75E-05 -1.86E-05 3.21E-05 2.41E-05 -2.54E-06 -1.12E-04 -7.75E-05 24hr Anneal 60 2.02E-05 -6.84E-05 5.99E-07 -3.34E-05 4.94E-06 6.86E-05 -2.51E-05 2.45E-05 2.09E-05 -1.44E-05 -1.11E-04 -7.82E-05 168hr Anneal 70 8.08E-06 -6.58E-05 -9.66E-06 -2.55E-05 -1.21E-05 2.90E-05 -5.25E-05 -4.47E-06 -2.06E-06 -4.42E-05 -1.11E-04 -7.91E-05 -3.63E-05 3.17E-05 5.07E-05 -1.23E-04 -1.55E-05 3.98E-05 9.35E-05 -1.25E-04 -1.52E-05 3.56E-05 8.24E-05 -1.13E-04 -2.10E-05 2.78E-05 5.51E-05 -9.71E-05 2.46E-06 3.51E-05 9.87E-05 -9.38E-05 -6.50E-04 PASS 6.50E-04 PASS 2.25E-05 3.69E-05 1.24E-04 -7.85E-05 -7.50E-04 PASS 7.50E-04 PASS 1.49E-05 3.70E-05 1.16E-04 -8.65E-05 -7.50E-04 PASS 7.50E-04 PASS -1.49E-05 3.34E-05 7.68E-05 -1.07E-04 -7.50E-04 PASS 7.50E-04 PASS 0 -2.22E-05 -8.46E-05 -3.33E-05 -5.54E-05 -4.15E-05 6.76E-06 -7.42E-05 -1.80E-05 -2.15E-05 -5.76E-05 -1.11E-04 -7.70E-05 Total 10 -2.91E-05 -9.40E-05 -4.44E-05 -6.93E-05 -5.60E-05 1.69E-05 -6.76E-05 -5.56E-06 -1.16E-05 -4.59E-05 -1.14E-04 -7.91E-05 Dose (krad(Si)) 20 30 -1.70E-05 -4.47E-06 -9.08E-05 -8.59E-05 -3.24E-05 -2.17E-05 -5.67E-05 -4.77E-05 -3.73E-05 -2.17E-05 3.46E-05 5.20E-05 -5.52E-05 -4.04E-05 3.98E-06 1.41E-05 -3.02E-06 6.15E-06 -3.10E-05 -1.96E-05 -1.12E-04 -1.13E-04 -7.83E-05 -7.85E-05 -4.74E-05 2.41E-05 1.86E-05 -1.13E-04 -5.86E-05 2.47E-05 9.26E-06 -1.26E-04 -4.68E-05 2.84E-05 3.09E-05 -1.25E-04 -3.29E-05 3.26E-05 5.64E-05 -1.22E-04 -4.50E-04 PASS 4.50E-04 PASS -2.27E-05 3.37E-05 6.96E-05 -1.15E-04 -6.00E-04 PASS 6.00E-04 PASS -1.01E-05 3.43E-05 8.41E-05 -1.04E-04 -6.00E-04 PASS 6.00E-04 PASS An ISO 9001:2008 and DSCC Certified Company 109 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-03 Offset Voltage 4 @ +5V (V) 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.52. Plot of Offset Voltage 4 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 110 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.52. Raw data for Offset Voltage 4 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Voltage 4 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 5.25E-05 1.05E-04 -3.10E-05 1.01E-04 5.25E-05 4.07E-05 9.79E-05 8.32E-05 -1.69E-06 4.08E-05 -5.52E-05 2.04E-05 24hr Anneal 60 4.48E-05 9.53E-05 -4.01E-05 9.28E-05 4.26E-05 3.51E-05 8.98E-05 7.14E-05 -1.17E-05 3.91E-05 -5.59E-05 1.97E-05 168hr Anneal 70 3.62E-05 7.69E-05 -5.86E-05 7.98E-05 1.98E-05 2.77E-06 7.50E-05 3.73E-05 -5.13E-05 9.65E-06 -5.59E-05 1.89E-05 3.46E-05 5.19E-05 1.77E-04 -1.08E-04 5.60E-05 5.49E-05 2.06E-04 -9.44E-05 4.71E-05 5.49E-05 1.98E-04 -1.03E-04 3.08E-05 5.63E-05 1.85E-04 -1.23E-04 2.99E-05 3.61E-05 1.29E-04 -6.91E-05 -6.50E-04 PASS 6.50E-04 PASS 5.22E-05 3.94E-05 1.60E-04 -5.59E-05 -7.50E-04 PASS 7.50E-04 PASS 4.48E-05 3.89E-05 1.51E-04 -6.19E-05 -7.50E-04 PASS 7.50E-04 PASS 1.47E-05 4.65E-05 1.42E-04 -1.13E-04 -7.50E-04 PASS 7.50E-04 PASS 0 -9.54E-06 5.20E-05 -6.54E-05 5.13E-05 -9.30E-06 -2.20E-05 1.56E-05 5.91E-06 -6.40E-05 2.02E-05 -5.73E-05 1.87E-05 Total 10 3.13E-06 6.58E-05 -5.83E-05 6.03E-05 3.58E-07 -1.06E-05 3.64E-05 2.72E-05 -4.76E-05 1.68E-05 -5.71E-05 1.92E-05 Dose (krad(Si)) 20 30 1.48E-05 2.62E-05 7.37E-05 8.59E-05 -4.96E-05 -4.31E-05 6.86E-05 7.86E-05 1.23E-05 2.53E-05 3.13E-06 1.58E-05 5.41E-05 7.07E-05 4.16E-05 5.66E-05 -3.67E-05 -2.14E-05 2.27E-05 2.75E-05 -5.62E-05 -5.70E-05 1.88E-05 1.99E-05 3.81E-06 4.93E-05 1.39E-04 -1.31E-04 1.43E-05 5.09E-05 1.54E-04 -1.25E-04 2.40E-05 5.02E-05 1.62E-04 -1.14E-04 -8.86E-06 3.49E-05 8.68E-05 -1.05E-04 -4.50E-04 PASS 4.50E-04 PASS 4.44E-06 3.40E-05 9.77E-05 -8.88E-05 -6.00E-04 PASS 6.00E-04 PASS 1.70E-05 3.57E-05 1.15E-04 -8.08E-05 -6.00E-04 PASS 6.00E-04 PASS An ISO 9001:2008 and DSCC Certified Company 111 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.00E-08 Offset Current 1 @ +5V (A) 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.53. Plot of Offset Current 1 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 112 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.53. Raw data for Offset Current 1 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Current 1 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 1.87E-10 2.42E-10 4.98E-10 8.90E-11 5.00E-11 4.10E-11 1.70E-10 2.61E-10 5.20E-11 -8.00E-11 -6.40E-11 3.70E-11 24hr Anneal 60 2.98E-10 3.90E-10 7.47E-10 6.60E-11 8.60E-11 3.50E-11 9.20E-11 1.32E-10 -2.20E-11 7.00E-12 -6.50E-11 5.90E-11 168hr Anneal 70 2.91E-10 7.40E-11 4.82E-10 5.00E-11 8.20E-11 7.00E-11 -4.70E-11 7.00E-11 -4.50E-11 4.80E-11 -7.10E-11 5.70E-11 8.92E-11 1.18E-10 4.12E-10 -2.34E-10 2.13E-10 1.77E-10 6.97E-10 -2.71E-10 3.17E-10 2.77E-10 1.08E-09 -4.42E-10 1.96E-10 1.87E-10 7.09E-10 -3.17E-10 -3.60E-11 5.79E-11 1.23E-10 -1.95E-10 -1.17E-08 PASS 1.17E-08 PASS 8.88E-11 1.31E-10 4.47E-10 -2.70E-10 -1.50E-08 PASS 1.50E-08 PASS 4.88E-11 6.27E-11 2.21E-10 -1.23E-10 -1.50E-08 PASS 1.50E-08 PASS 1.92E-11 6.02E-11 1.84E-10 -1.46E-10 -1.50E-08 PASS 1.50E-08 PASS 0 -6.00E-12 1.01E-10 -2.70E-11 -6.50E-11 -1.51E-10 -1.06E-10 -4.20E-11 -1.16E-10 -1.18E-10 3.20E-11 -4.50E-11 6.30E-11 Total 10 2.20E-11 1.45E-10 -8.00E-12 -6.10E-11 -1.01E-10 -7.90E-11 -6.70E-11 -6.20E-11 -1.51E-10 1.00E-11 -8.60E-11 2.60E-11 Dose (krad(Si)) 20 30 8.20E-11 9.40E-11 1.64E-10 2.06E-10 1.50E-10 1.93E-10 -1.10E-11 3.00E-11 -9.60E-11 -7.70E-11 -3.90E-11 -1.03E-10 -1.70E-11 -2.10E-11 1.60E-11 3.90E-11 -7.80E-11 -1.00E-11 -6.10E-11 -8.50E-11 -6.50E-11 -5.80E-11 4.00E-11 4.40E-11 -2.96E-11 9.17E-11 2.22E-10 -2.81E-10 -6.00E-13 9.42E-11 2.58E-10 -2.59E-10 5.78E-11 1.10E-10 3.61E-10 -2.45E-10 -7.00E-11 6.50E-11 1.08E-10 -2.48E-10 -1.00E-08 PASS 1.00E-08 PASS -6.98E-11 5.73E-11 8.72E-11 -2.27E-10 -1.00E-08 PASS 1.00E-08 PASS -3.58E-11 3.70E-11 6.55E-11 -1.37E-10 -1.00E-08 PASS 1.00E-08 PASS An ISO 9001:2008 and DSCC Certified Company 113 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.00E-08 Offset Current 2 @ +5V (A) 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.54. Plot of Offset Current 2 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 114 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.54. Raw data for Offset Current 2 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Current 2 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 -1.01E-10 2.40E-11 2.97E-10 3.04E-10 4.35E-10 1.91E-10 1.64E-10 8.40E-11 7.80E-11 7.70E-11 -3.10E-11 9.10E-11 24hr Anneal 60 1.14E-10 1.36E-10 1.89E-10 3.78E-10 4.12E-10 2.00E-11 9.40E-11 -2.00E-11 7.10E-11 1.72E-10 -3.30E-11 7.90E-11 168hr Anneal 70 1.94E-10 -2.90E-11 3.30E-11 3.53E-10 3.09E-10 2.90E-11 4.40E-11 8.10E-11 1.28E-10 1.50E-10 -1.70E-11 8.10E-11 8.50E-11 1.58E-10 5.19E-10 -3.49E-10 1.92E-10 2.22E-10 8.00E-10 -4.16E-10 2.46E-10 1.39E-10 6.28E-10 -1.36E-10 1.72E-10 1.67E-10 6.30E-10 -2.86E-10 1.70E-11 6.02E-11 1.82E-10 -1.48E-10 -1.17E-08 PASS 1.17E-08 PASS 1.19E-10 5.45E-11 2.68E-10 -3.06E-11 -1.50E-08 PASS 1.50E-08 PASS 6.74E-11 7.34E-11 2.69E-10 -1.34E-10 -1.50E-08 PASS 1.50E-08 PASS 8.64E-11 5.22E-11 2.30E-10 -5.67E-11 -1.50E-08 PASS 1.50E-08 PASS 0 -1.44E-10 6.00E-11 -1.49E-10 -4.00E-11 3.50E-11 -5.00E-11 -9.60E-11 -9.30E-11 5.00E-11 -3.30E-11 -3.70E-11 9.70E-11 Total 10 -8.60E-11 4.90E-11 -1.24E-10 1.20E-11 0.00E+00 2.70E-11 -4.90E-11 -9.50E-11 4.40E-11 3.10E-11 -2.30E-11 8.60E-11 Dose (krad(Si)) 20 30 -1.73E-10 -1.38E-10 1.50E-11 5.90E-11 -1.24E-10 4.80E-11 1.92E-10 2.89E-10 7.90E-11 1.67E-10 5.00E-12 9.20E-11 -1.38E-10 -6.90E-11 -9.10E-11 -6.00E-12 7.00E-11 4.80E-11 -2.00E-12 2.00E-11 -4.30E-11 -7.00E-12 7.20E-11 7.90E-11 -4.76E-11 9.75E-11 2.20E-10 -3.15E-10 -2.98E-11 7.22E-11 1.68E-10 -2.28E-10 -2.20E-12 1.49E-10 4.06E-10 -4.10E-10 -4.44E-11 5.94E-11 1.18E-10 -2.07E-10 -1.00E-08 PASS 1.00E-08 PASS -8.40E-12 6.06E-11 1.58E-10 -1.75E-10 -1.00E-08 PASS 1.00E-08 PASS -3.12E-11 8.27E-11 1.96E-10 -2.58E-10 -1.00E-08 PASS 1.00E-08 PASS An ISO 9001:2008 and DSCC Certified Company 115 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.00E-08 Offset Current 3 @ +5V (A) 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.55. Plot of Offset Current 3 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 116 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.55. Raw data for Offset Current 3 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Current 3 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 3.50E-10 2.04E-10 2.88E-10 3.05E-10 3.60E-11 2.20E-10 -5.50E-11 1.61E-10 -6.30E-11 3.28E-10 2.50E-11 7.10E-11 24hr Anneal 60 2.28E-10 1.12E-10 2.74E-10 1.43E-10 4.30E-11 2.09E-10 -1.36E-10 2.18E-10 -2.40E-11 2.92E-10 9.00E-12 6.60E-11 168hr Anneal 70 1.54E-10 2.17E-10 3.47E-10 1.08E-10 2.58E-10 1.36E-10 -1.12E-10 6.00E-11 1.06E-10 6.00E-11 2.90E-11 4.40E-11 5.24E-11 1.08E-10 3.49E-10 -2.44E-10 2.37E-10 1.24E-10 5.77E-10 -1.03E-10 1.60E-10 9.21E-11 4.12E-10 -9.24E-11 2.17E-10 9.28E-11 4.71E-10 -3.76E-11 3.78E-11 9.22E-11 2.91E-10 -2.15E-10 -1.17E-08 PASS 1.17E-08 PASS 1.18E-10 1.73E-10 5.91E-10 -3.55E-10 -1.50E-08 PASS 1.50E-08 PASS 1.12E-10 1.82E-10 6.12E-10 -3.88E-10 -1.50E-08 PASS 1.50E-08 PASS 5.00E-11 9.61E-11 3.14E-10 -2.14E-10 -1.50E-08 PASS 1.50E-08 PASS 0 -3.60E-11 -1.50E-11 -8.00E-11 -1.23E-10 -1.47E-10 -1.40E-11 -2.60E-11 -1.50E-11 -4.80E-11 -3.00E-12 1.50E-11 3.60E-11 Total 10 -4.90E-11 3.60E-11 -6.20E-11 -9.70E-11 -9.80E-11 1.60E-11 -5.00E-11 2.90E-11 -7.40E-11 7.10E-11 1.60E-11 7.50E-11 Dose (krad(Si)) 20 30 4.00E-11 6.90E-11 5.70E-11 1.26E-10 -1.20E-11 1.68E-10 -6.70E-11 7.00E-12 -1.11E-10 -1.08E-10 4.60E-11 3.00E-11 -1.08E-10 -9.10E-11 3.60E-11 7.70E-11 -4.60E-11 1.20E-11 1.11E-10 1.61E-10 2.80E-11 3.40E-11 5.90E-11 7.50E-11 -8.02E-11 5.59E-11 7.31E-11 -2.33E-10 -5.40E-11 5.47E-11 9.60E-11 -2.04E-10 -1.86E-11 7.08E-11 1.76E-10 -2.13E-10 -2.12E-11 1.70E-11 2.56E-11 -6.80E-11 -1.00E-08 PASS 1.00E-08 PASS -1.60E-12 5.94E-11 1.61E-10 -1.64E-10 -1.00E-08 PASS 1.00E-08 PASS 7.80E-12 8.55E-11 2.42E-10 -2.27E-10 -1.00E-08 PASS 1.00E-08 PASS An ISO 9001:2008 and DSCC Certified Company 117 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.00E-08 Offset Current 4 @ +5V (A) 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.56. Plot of Offset Current 4 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 118 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.56. Raw data for Offset Current 4 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Offset Current 4 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 50 1.56E-10 9.00E-12 4.22E-10 -8.70E-11 1.92E-10 -1.14E-10 9.80E-11 1.18E-10 1.45E-10 -1.20E-10 6.20E-11 -2.60E-11 24hr Anneal 60 2.77E-10 1.56E-10 4.39E-10 1.37E-10 2.41E-10 -2.75E-10 -3.60E-11 8.80E-11 -1.00E-11 -2.93E-10 7.40E-11 0.00E+00 168hr Anneal 70 2.08E-10 1.68E-10 4.66E-10 3.60E-11 1.95E-10 -3.80E-11 3.10E-11 1.27E-10 -1.29E-10 -4.30E-11 6.10E-11 -5.00E-12 7.34E-11 6.68E-11 2.57E-10 -1.10E-10 1.38E-10 1.94E-10 6.71E-10 -3.95E-10 2.50E-10 1.21E-10 5.81E-10 -8.06E-11 2.15E-10 1.56E-10 6.43E-10 -2.14E-10 -8.20E-12 9.69E-11 2.58E-10 -2.74E-10 -1.17E-08 PASS 1.17E-08 PASS 2.54E-11 1.31E-10 3.85E-10 -3.34E-10 -1.50E-08 PASS 1.50E-08 PASS -1.05E-10 1.70E-10 3.60E-10 -5.71E-10 -1.50E-08 PASS 1.50E-08 PASS -1.04E-11 9.55E-11 2.51E-10 -2.72E-10 -1.50E-08 PASS 1.50E-08 PASS 0 -1.40E-11 -1.00E-11 3.40E-11 -8.40E-11 -6.10E-11 -1.90E-10 1.20E-11 4.40E-11 -8.50E-11 -2.30E-11 6.80E-11 1.20E-11 Total 10 4.50E-11 1.90E-11 2.10E-11 -9.70E-11 2.30E-11 -1.99E-10 1.20E-11 3.00E-11 -5.00E-11 -5.90E-11 4.90E-11 2.00E-12 Dose (krad(Si)) 20 30 4.20E-11 4.80E-11 6.20E-11 1.40E-11 9.70E-11 1.49E-10 -4.70E-11 1.50E-11 6.80E-11 1.41E-10 -1.42E-10 -1.02E-10 3.90E-11 1.20E-11 5.20E-11 9.50E-11 -9.00E-12 7.00E-11 -4.50E-11 -1.16E-10 4.80E-11 5.00E-11 1.00E-11 2.40E-11 -2.70E-11 4.63E-11 1.00E-10 -1.54E-10 2.20E-12 5.64E-11 1.57E-10 -1.53E-10 4.44E-11 5.48E-11 1.95E-10 -1.06E-10 -4.84E-11 9.25E-11 2.05E-10 -3.02E-10 -1.00E-08 PASS 1.00E-08 PASS -5.32E-11 9.01E-11 1.94E-10 -3.00E-10 -1.00E-08 PASS 1.00E-08 PASS -2.10E-11 7.79E-11 1.93E-10 -2.35E-10 -1.00E-08 PASS 1.00E-08 PASS An ISO 9001:2008 and DSCC Certified Company 119 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Bias Current 1 @ +5V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.57. Plot of Positive Bias Current 1 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 120 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.57. Raw data for Positive Bias Current 1 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Bias Current 1 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.51E-08 1.77E-08 1.54E-08 1.79E-08 1.61E-08 1.87E-08 1.63E-08 1.90E-08 1.50E-08 1.75E-08 1.50E-08 1.73E-08 1.58E-08 1.79E-08 1.57E-08 1.79E-08 1.61E-08 1.84E-08 1.47E-08 1.69E-08 1.12E-08 1.12E-08 1.14E-08 1.13E-08 50 2.25E-08 2.27E-08 2.40E-08 2.43E-08 2.24E-08 2.07E-08 2.16E-08 2.16E-08 2.19E-08 2.02E-08 1.12E-08 1.13E-08 24hr Anneal 60 2.48E-08 2.49E-08 2.62E-08 2.66E-08 2.45E-08 2.11E-08 2.19E-08 2.20E-08 2.25E-08 2.04E-08 1.12E-08 1.13E-08 168hr Anneal 70 2.42E-08 2.46E-08 2.59E-08 2.62E-08 2.41E-08 1.93E-08 2.01E-08 2.02E-08 2.08E-08 1.88E-08 1.12E-08 1.14E-08 0 1.16E-08 1.20E-08 1.22E-08 1.23E-08 1.16E-08 1.16E-08 1.23E-08 1.23E-08 1.26E-08 1.14E-08 1.12E-08 1.13E-08 Total 10 1.30E-08 1.33E-08 1.38E-08 1.40E-08 1.28E-08 1.32E-08 1.39E-08 1.38E-08 1.43E-08 1.28E-08 1.12E-08 1.14E-08 1.19E-08 3.18E-10 1.28E-08 1.10E-08 1.34E-08 4.83E-10 1.47E-08 1.21E-08 1.56E-08 5.93E-10 1.72E-08 1.40E-08 1.82E-08 6.49E-10 1.99E-08 1.64E-08 2.32E-08 9.05E-10 2.56E-08 2.07E-08 2.54E-08 9.29E-10 2.80E-08 2.29E-08 2.50E-08 9.60E-10 2.76E-08 2.24E-08 1.20E-08 5.20E-10 1.35E-08 1.06E-08 -5.00E-08 PASS 5.00E-08 PASS 1.36E-08 5.66E-10 1.51E-08 1.20E-08 -8.00E-08 PASS 8.00E-08 PASS 1.55E-08 5.91E-10 1.71E-08 1.39E-08 -1.00E-07 PASS 1.00E-07 PASS 1.77E-08 6.17E-10 1.94E-08 1.60E-08 -1.08E-07 PASS 1.08E-07 PASS 2.12E-08 7.19E-10 2.32E-08 1.92E-08 -1.25E-07 PASS 1.25E-07 PASS 2.16E-08 8.24E-10 2.38E-08 1.93E-08 -1.25E-07 PASS 1.25E-07 PASS 1.98E-08 8.05E-10 2.20E-08 1.76E-08 -1.25E-07 PASS 1.25E-07 PASS An ISO 9001:2008 and DSCC Certified Company 121 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Bias Current 2 @ +5V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.58. Plot of Positive Bias Current 2 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 122 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.58. Raw data for Positive Bias Current 2 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Bias Current 2 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.65E-08 1.92E-08 1.53E-08 1.78E-08 1.65E-08 1.90E-08 1.66E-08 1.93E-08 1.55E-08 1.80E-08 1.66E-08 1.90E-08 1.63E-08 1.85E-08 1.63E-08 1.84E-08 1.46E-08 1.67E-08 1.51E-08 1.73E-08 1.20E-08 1.20E-08 1.12E-08 1.12E-08 50 2.43E-08 2.29E-08 2.43E-08 2.46E-08 2.29E-08 2.29E-08 2.22E-08 2.23E-08 2.03E-08 2.10E-08 1.20E-08 1.12E-08 24hr Anneal 60 2.67E-08 2.50E-08 2.66E-08 2.69E-08 2.52E-08 2.34E-08 2.26E-08 2.25E-08 2.04E-08 2.13E-08 1.20E-08 1.12E-08 168hr Anneal 70 2.63E-08 2.40E-08 2.61E-08 2.64E-08 2.49E-08 2.12E-08 2.06E-08 2.04E-08 1.83E-08 1.94E-08 1.20E-08 1.12E-08 0 1.28E-08 1.15E-08 1.25E-08 1.25E-08 1.20E-08 1.28E-08 1.25E-08 1.25E-08 1.10E-08 1.17E-08 1.20E-08 1.12E-08 Total 10 1.42E-08 1.31E-08 1.41E-08 1.42E-08 1.35E-08 1.45E-08 1.42E-08 1.42E-08 1.26E-08 1.32E-08 1.20E-08 1.12E-08 1.22E-08 5.27E-10 1.37E-08 1.08E-08 1.38E-08 5.19E-10 1.53E-08 1.24E-08 1.61E-08 6.21E-10 1.78E-08 1.44E-08 1.87E-08 6.83E-10 2.05E-08 1.68E-08 2.38E-08 8.38E-10 2.61E-08 2.15E-08 2.61E-08 9.16E-10 2.86E-08 2.36E-08 2.55E-08 1.05E-09 2.84E-08 2.27E-08 1.21E-08 7.43E-10 1.41E-08 1.01E-08 -5.00E-08 PASS 5.00E-08 PASS 1.37E-08 7.99E-10 1.59E-08 1.15E-08 -8.00E-08 PASS 8.00E-08 PASS 1.57E-08 8.74E-10 1.81E-08 1.33E-08 -1.00E-07 PASS 1.00E-07 PASS 1.80E-08 9.35E-10 2.06E-08 1.54E-08 -1.08E-07 PASS 1.08E-07 PASS 2.18E-08 1.04E-09 2.46E-08 1.89E-08 -1.25E-07 PASS 1.25E-07 PASS 2.20E-08 1.18E-09 2.53E-08 1.88E-08 -1.25E-07 PASS 1.25E-07 PASS 2.00E-08 1.14E-09 2.31E-08 1.69E-08 -1.25E-07 PASS 1.25E-07 PASS An ISO 9001:2008 and DSCC Certified Company 123 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Bias Current 3 @ +5V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.59. Plot of Positive Bias Current 3 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 124 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.59. Raw data for Positive Bias Current 3 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Bias Current 3 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.51E-08 1.76E-08 1.55E-08 1.81E-08 1.57E-08 1.81E-08 1.59E-08 1.84E-08 1.57E-08 1.83E-08 1.60E-08 1.84E-08 1.54E-08 1.77E-08 1.56E-08 1.78E-08 1.49E-08 1.70E-08 1.46E-08 1.68E-08 1.14E-08 1.14E-08 1.08E-08 1.08E-08 50 2.25E-08 2.30E-08 2.31E-08 2.35E-08 2.33E-08 2.22E-08 2.14E-08 2.15E-08 2.07E-08 2.03E-08 1.14E-08 1.08E-08 24hr Anneal 60 2.49E-08 2.52E-08 2.54E-08 2.57E-08 2.56E-08 2.25E-08 2.17E-08 2.17E-08 2.09E-08 2.06E-08 1.14E-08 1.08E-08 168hr Anneal 70 2.43E-08 2.43E-08 2.49E-08 2.52E-08 2.51E-08 2.05E-08 1.98E-08 1.98E-08 1.88E-08 1.89E-08 1.14E-08 1.08E-08 0 1.17E-08 1.17E-08 1.19E-08 1.19E-08 1.23E-08 1.23E-08 1.18E-08 1.20E-08 1.13E-08 1.13E-08 1.14E-08 1.07E-08 Total 10 1.31E-08 1.33E-08 1.36E-08 1.36E-08 1.36E-08 1.41E-08 1.35E-08 1.36E-08 1.29E-08 1.28E-08 1.15E-08 1.08E-08 1.19E-08 2.42E-10 1.26E-08 1.12E-08 1.34E-08 2.36E-10 1.41E-08 1.28E-08 1.56E-08 3.03E-10 1.64E-08 1.48E-08 1.81E-08 3.27E-10 1.90E-08 1.72E-08 2.31E-08 3.98E-10 2.42E-08 2.20E-08 2.53E-08 3.37E-10 2.63E-08 2.44E-08 2.48E-08 4.50E-10 2.60E-08 2.35E-08 1.17E-08 4.54E-10 1.30E-08 1.05E-08 -5.00E-08 PASS 5.00E-08 PASS 1.34E-08 5.26E-10 1.48E-08 1.19E-08 -8.00E-08 PASS 8.00E-08 PASS 1.53E-08 5.53E-10 1.68E-08 1.38E-08 -1.00E-07 PASS 1.00E-07 PASS 1.75E-08 6.36E-10 1.93E-08 1.58E-08 -1.08E-07 PASS 1.08E-07 PASS 2.12E-08 7.41E-10 2.32E-08 1.92E-08 -1.25E-07 PASS 1.25E-07 PASS 2.15E-08 7.70E-10 2.36E-08 1.94E-08 -1.25E-07 PASS 1.25E-07 PASS 1.95E-08 7.05E-10 2.15E-08 1.76E-08 -1.25E-07 PASS 1.25E-07 PASS An ISO 9001:2008 and DSCC Certified Company 125 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Bias Current 4 @ +5V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.60. Plot of Positive Bias Current 4 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 126 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.60. Raw data for Positive Bias Current 4 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Bias Current 4 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.66E-08 1.93E-08 1.60E-08 1.86E-08 1.69E-08 1.97E-08 1.71E-08 1.97E-08 1.54E-08 1.79E-08 1.64E-08 1.87E-08 1.62E-08 1.85E-08 1.55E-08 1.77E-08 1.61E-08 1.82E-08 1.45E-08 1.67E-08 1.16E-08 1.16E-08 1.19E-08 1.19E-08 50 2.45E-08 2.37E-08 2.52E-08 2.52E-08 2.30E-08 2.25E-08 2.21E-08 2.14E-08 2.18E-08 2.00E-08 1.16E-08 1.19E-08 24hr Anneal 60 2.70E-08 2.60E-08 2.77E-08 2.74E-08 2.52E-08 2.31E-08 2.26E-08 2.18E-08 2.24E-08 2.04E-08 1.16E-08 1.19E-08 168hr Anneal 70 2.64E-08 2.55E-08 2.73E-08 2.71E-08 2.48E-08 2.09E-08 2.06E-08 2.00E-08 2.07E-08 1.85E-08 1.16E-08 1.19E-08 0 1.27E-08 1.24E-08 1.28E-08 1.28E-08 1.19E-08 1.28E-08 1.27E-08 1.20E-08 1.25E-08 1.13E-08 1.16E-08 1.19E-08 Total 10 1.42E-08 1.38E-08 1.44E-08 1.46E-08 1.32E-08 1.44E-08 1.42E-08 1.36E-08 1.41E-08 1.28E-08 1.16E-08 1.19E-08 1.25E-08 3.71E-10 1.36E-08 1.15E-08 1.41E-08 5.73E-10 1.56E-08 1.25E-08 1.64E-08 7.04E-10 1.83E-08 1.45E-08 1.90E-08 7.57E-10 2.11E-08 1.70E-08 2.43E-08 9.73E-10 2.70E-08 2.17E-08 2.67E-08 1.04E-09 2.95E-08 2.38E-08 2.62E-08 1.06E-09 2.91E-08 2.33E-08 1.22E-08 6.12E-10 1.39E-08 1.06E-08 -5.00E-08 PASS 5.00E-08 PASS 1.38E-08 6.79E-10 1.57E-08 1.20E-08 -8.00E-08 PASS 8.00E-08 PASS 1.57E-08 7.39E-10 1.78E-08 1.37E-08 -1.00E-07 PASS 1.00E-07 PASS 1.80E-08 7.92E-10 2.01E-08 1.58E-08 -1.08E-07 PASS 1.08E-07 PASS 2.16E-08 9.49E-10 2.42E-08 1.90E-08 -1.25E-07 PASS 1.25E-07 PASS 2.21E-08 1.03E-09 2.49E-08 1.92E-08 -1.25E-07 PASS 1.25E-07 PASS 2.02E-08 9.64E-10 2.28E-08 1.75E-08 -1.25E-07 PASS 1.25E-07 PASS An ISO 9001:2008 and DSCC Certified Company 127 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Bias Current 1 @ +5V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.61. Plot of Negative Bias Current 1 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 128 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.61. Raw data for Negative Bias Current 1 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Bias Current 1 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.52E-08 1.78E-08 1.56E-08 1.81E-08 1.63E-08 1.90E-08 1.63E-08 1.91E-08 1.49E-08 1.75E-08 1.50E-08 1.73E-08 1.58E-08 1.80E-08 1.58E-08 1.80E-08 1.61E-08 1.84E-08 1.46E-08 1.68E-08 1.12E-08 1.12E-08 1.14E-08 1.14E-08 50 2.27E-08 2.29E-08 2.46E-08 2.44E-08 2.25E-08 2.08E-08 2.18E-08 2.19E-08 2.20E-08 2.02E-08 1.12E-08 1.14E-08 24hr Anneal 60 2.51E-08 2.53E-08 2.70E-08 2.67E-08 2.46E-08 2.11E-08 2.20E-08 2.22E-08 2.25E-08 2.05E-08 1.12E-08 1.14E-08 168hr Anneal 70 2.46E-08 2.47E-08 2.64E-08 2.63E-08 2.43E-08 1.94E-08 2.01E-08 2.03E-08 2.08E-08 1.88E-08 1.12E-08 1.14E-08 0 1.15E-08 1.21E-08 1.22E-08 1.22E-08 1.15E-08 1.15E-08 1.23E-08 1.22E-08 1.25E-08 1.14E-08 1.11E-08 1.14E-08 Total 10 1.31E-08 1.34E-08 1.37E-08 1.39E-08 1.28E-08 1.32E-08 1.39E-08 1.38E-08 1.42E-08 1.29E-08 1.12E-08 1.14E-08 1.19E-08 3.66E-10 1.29E-08 1.09E-08 1.34E-08 4.66E-10 1.47E-08 1.21E-08 1.57E-08 6.22E-10 1.74E-08 1.40E-08 1.83E-08 7.02E-10 2.02E-08 1.64E-08 2.34E-08 9.96E-10 2.62E-08 2.07E-08 2.58E-08 1.04E-09 2.86E-08 2.29E-08 2.53E-08 1.00E-09 2.80E-08 2.25E-08 1.20E-08 5.04E-10 1.34E-08 1.06E-08 -5.00E-08 PASS 5.00E-08 PASS 1.36E-08 5.26E-10 1.50E-08 1.21E-08 -8.00E-08 PASS 8.00E-08 PASS 1.55E-08 6.11E-10 1.72E-08 1.38E-08 -1.00E-07 PASS 1.00E-07 PASS 1.77E-08 6.47E-10 1.95E-08 1.59E-08 -1.08E-07 PASS 1.08E-07 PASS 2.13E-08 8.13E-10 2.35E-08 1.91E-08 -1.25E-07 PASS 1.25E-07 PASS 2.17E-08 8.51E-10 2.40E-08 1.93E-08 -1.25E-07 PASS 1.25E-07 PASS 1.99E-08 7.68E-10 2.20E-08 1.78E-08 -1.25E-07 PASS 1.25E-07 PASS An ISO 9001:2008 and DSCC Certified Company 129 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Bias Current 2 @ +5V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.62. Plot of Negative Bias Current 2 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 130 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.62. Raw data for Negative Bias Current 2 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Bias Current 2 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.64E-08 1.91E-08 1.54E-08 1.79E-08 1.64E-08 1.91E-08 1.68E-08 1.96E-08 1.56E-08 1.82E-08 1.66E-08 1.91E-08 1.61E-08 1.85E-08 1.62E-08 1.85E-08 1.47E-08 1.68E-08 1.51E-08 1.74E-08 1.20E-08 1.20E-08 1.13E-08 1.13E-08 50 2.43E-08 2.30E-08 2.46E-08 2.49E-08 2.34E-08 2.31E-08 2.25E-08 2.25E-08 2.04E-08 2.12E-08 1.19E-08 1.13E-08 24hr Anneal 60 2.69E-08 2.52E-08 2.69E-08 2.73E-08 2.56E-08 2.34E-08 2.27E-08 2.27E-08 2.05E-08 2.15E-08 1.19E-08 1.13E-08 168hr Anneal 70 2.66E-08 2.41E-08 2.62E-08 2.68E-08 2.53E-08 2.13E-08 2.07E-08 2.06E-08 1.85E-08 1.96E-08 1.20E-08 1.13E-08 0 1.27E-08 1.15E-08 1.24E-08 1.25E-08 1.20E-08 1.27E-08 1.24E-08 1.25E-08 1.11E-08 1.17E-08 1.19E-08 1.13E-08 Total 10 1.41E-08 1.32E-08 1.41E-08 1.43E-08 1.35E-08 1.46E-08 1.42E-08 1.41E-08 1.27E-08 1.33E-08 1.21E-08 1.13E-08 1.22E-08 4.49E-10 1.35E-08 1.10E-08 1.38E-08 4.70E-10 1.51E-08 1.25E-08 1.61E-08 6.10E-10 1.78E-08 1.44E-08 1.88E-08 6.88E-10 2.07E-08 1.69E-08 2.41E-08 8.13E-10 2.63E-08 2.18E-08 2.64E-08 9.29E-10 2.89E-08 2.39E-08 2.58E-08 1.11E-09 2.88E-08 2.27E-08 1.21E-08 6.80E-10 1.39E-08 1.02E-08 -5.00E-08 PASS 5.00E-08 PASS 1.38E-08 7.76E-10 1.59E-08 1.16E-08 -8.00E-08 PASS 8.00E-08 PASS 1.57E-08 8.18E-10 1.80E-08 1.35E-08 -1.00E-07 PASS 1.00E-07 PASS 1.81E-08 9.41E-10 2.06E-08 1.55E-08 -1.08E-07 PASS 1.08E-07 PASS 2.19E-08 1.11E-09 2.50E-08 1.89E-08 -1.25E-07 PASS 1.25E-07 PASS 2.22E-08 1.16E-09 2.53E-08 1.90E-08 -1.25E-07 PASS 1.25E-07 PASS 2.01E-08 1.09E-09 2.31E-08 1.72E-08 -1.25E-07 PASS 1.25E-07 PASS An ISO 9001:2008 and DSCC Certified Company 131 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Bias Current 3 @ +5V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.63. Plot of Negative Bias Current 3 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 132 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.63. Raw data for Negative Bias Current 3 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Bias Current 3 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.52E-08 1.77E-08 1.56E-08 1.82E-08 1.58E-08 1.82E-08 1.59E-08 1.85E-08 1.57E-08 1.83E-08 1.60E-08 1.85E-08 1.54E-08 1.76E-08 1.57E-08 1.79E-08 1.49E-08 1.71E-08 1.48E-08 1.70E-08 1.15E-08 1.15E-08 1.08E-08 1.08E-08 50 2.28E-08 2.34E-08 2.35E-08 2.39E-08 2.33E-08 2.24E-08 2.13E-08 2.18E-08 2.07E-08 2.07E-08 1.15E-08 1.08E-08 24hr Anneal 60 2.51E-08 2.54E-08 2.58E-08 2.60E-08 2.56E-08 2.28E-08 2.16E-08 2.20E-08 2.08E-08 2.09E-08 1.14E-08 1.08E-08 168hr Anneal 70 2.45E-08 2.46E-08 2.53E-08 2.54E-08 2.55E-08 2.07E-08 1.97E-08 1.99E-08 1.89E-08 1.90E-08 1.14E-08 1.08E-08 0 1.17E-08 1.17E-08 1.18E-08 1.18E-08 1.22E-08 1.23E-08 1.19E-08 1.20E-08 1.13E-08 1.13E-08 1.14E-08 1.08E-08 Total 10 1.30E-08 1.34E-08 1.35E-08 1.35E-08 1.35E-08 1.41E-08 1.35E-08 -2.52E-08 1.29E-08 1.29E-08 1.15E-08 1.08E-08 1.18E-08 1.86E-10 1.23E-08 1.13E-08 1.34E-08 2.05E-10 1.40E-08 1.28E-08 1.56E-08 2.60E-10 1.63E-08 1.49E-08 1.82E-08 2.89E-10 1.90E-08 1.74E-08 2.34E-08 3.75E-10 2.44E-08 2.23E-08 2.56E-08 3.51E-10 2.65E-08 2.46E-08 2.50E-08 4.85E-10 2.64E-08 2.37E-08 1.18E-08 4.54E-10 1.30E-08 1.05E-08 -5.00E-08 PASS 5.00E-08 PASS 5.64E-09 1.73E-08 5.29E-08 -4.17E-08 -8.00E-08 PASS 8.00E-08 PASS 1.54E-08 5.38E-10 1.68E-08 1.39E-08 -1.00E-07 PASS 1.00E-07 PASS 1.76E-08 6.07E-10 1.93E-08 1.60E-08 -1.08E-07 PASS 1.08E-07 PASS 2.14E-08 7.45E-10 2.34E-08 1.93E-08 -1.25E-07 PASS 1.25E-07 PASS 2.16E-08 8.09E-10 2.38E-08 1.94E-08 -1.25E-07 PASS 1.25E-07 PASS 1.96E-08 7.33E-10 2.17E-08 1.76E-08 -1.25E-07 PASS 1.25E-07 PASS An ISO 9001:2008 and DSCC Certified Company 133 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Bias Current 4 @ +5V (A) 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.64. Plot of Negative Bias Current 4 @ +5V (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 134 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.64. Raw data for Negative Bias Current 4 @ +5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Bias Current 4 @ +5V (A) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Dose (krad(Si)) 20 30 1.66E-08 1.94E-08 1.60E-08 1.87E-08 1.71E-08 1.99E-08 1.71E-08 1.97E-08 1.55E-08 1.82E-08 1.63E-08 1.87E-08 1.63E-08 1.86E-08 1.57E-08 1.79E-08 1.61E-08 1.84E-08 1.45E-08 1.66E-08 1.17E-08 1.17E-08 1.19E-08 1.19E-08 50 2.48E-08 2.37E-08 2.57E-08 2.51E-08 2.32E-08 2.24E-08 2.23E-08 2.15E-08 2.20E-08 1.99E-08 1.17E-08 1.19E-08 24hr Anneal 60 2.73E-08 2.62E-08 2.82E-08 2.76E-08 2.55E-08 2.28E-08 2.26E-08 2.19E-08 2.24E-08 2.02E-08 1.17E-08 1.19E-08 168hr Anneal 70 2.67E-08 2.57E-08 2.78E-08 2.71E-08 2.51E-08 2.09E-08 2.07E-08 2.02E-08 2.05E-08 1.86E-08 1.17E-08 1.19E-08 0 1.27E-08 1.24E-08 1.28E-08 1.28E-08 1.19E-08 1.26E-08 1.27E-08 1.21E-08 1.24E-08 1.13E-08 1.16E-08 1.19E-08 Total 10 1.43E-08 1.39E-08 1.45E-08 1.46E-08 1.32E-08 1.43E-08 1.43E-08 1.36E-08 1.41E-08 1.27E-08 1.17E-08 1.19E-08 1.25E-08 3.83E-10 1.36E-08 1.15E-08 1.41E-08 5.61E-10 1.56E-08 1.25E-08 1.65E-08 6.95E-10 1.84E-08 1.45E-08 1.92E-08 7.09E-10 2.11E-08 1.72E-08 2.45E-08 1.02E-09 2.73E-08 2.17E-08 2.70E-08 1.10E-09 3.00E-08 2.40E-08 2.65E-08 1.12E-09 2.95E-08 2.34E-08 1.22E-08 5.83E-10 1.38E-08 1.06E-08 -5.00E-08 PASS 5.00E-08 PASS 1.38E-08 6.74E-10 1.57E-08 1.20E-08 -8.00E-08 PASS 8.00E-08 PASS 1.58E-08 7.60E-10 1.78E-08 1.37E-08 -1.00E-07 PASS 1.00E-07 PASS 1.80E-08 8.37E-10 2.03E-08 1.57E-08 -1.08E-07 PASS 1.08E-07 PASS 2.16E-08 1.00E-09 2.44E-08 1.89E-08 -1.25E-07 PASS 1.25E-07 PASS 2.20E-08 1.08E-09 2.49E-08 1.90E-08 -1.25E-07 PASS 1.25E-07 PASS 2.02E-08 9.22E-10 2.27E-08 1.77E-08 -1.25E-07 PASS 1.25E-07 PASS An ISO 9001:2008 and DSCC Certified Company 135 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Positive Output Voltage 1 RL=open @ +5V (V) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 4.35E+00 4.30E+00 4.25E+00 4.20E+00 4.15E+00 4.10E+00 4.05E+00 4.00E+00 3.95E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.65. Plot of Positive Output Voltage 1 RL=open @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 136 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.65. Raw data for Positive Output Voltage 1 RL=open @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 1 RL=open @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.27E+00 4.26E+00 4.27E+00 4.26E+00 4.26E+00 4.27E+00 4.27E+00 4.27E+00 24hr Anneal 60 4.29E+00 4.28E+00 4.28E+00 4.28E+00 4.29E+00 4.27E+00 4.28E+00 4.27E+00 4.27E+00 4.28E+00 4.27E+00 4.27E+00 168hr Anneal 70 4.29E+00 4.30E+00 4.30E+00 4.30E+00 4.29E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.29E+00 4.27E+00 4.27E+00 4.26E+00 1.73E-03 4.26E+00 4.26E+00 4.27E+00 3.35E-03 4.28E+00 4.26E+00 4.28E+00 6.87E-03 4.30E+00 4.26E+00 4.30E+00 3.49E-03 4.31E+00 4.29E+00 4.26E+00 4.32E-03 4.27E+00 4.25E+00 4.00E+00 PASS 4.26E+00 3.96E-03 4.28E+00 4.25E+00 4.00E+00 PASS 4.27E+00 3.78E-03 4.28E+00 4.26E+00 4.00E+00 PASS 4.28E+00 4.44E-03 4.29E+00 4.27E+00 4.00E+00 PASS 0 4.27E+00 4.26E+00 4.27E+00 4.26E+00 4.26E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.28E+00 4.27E+00 4.27E+00 Total 10 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.27E+00 4.25E+00 4.26E+00 4.25E+00 4.25E+00 4.26E+00 4.27E+00 4.27E+00 Dose (krad(Si)) 20 30 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.25E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.25E+00 4.26E+00 4.26E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.82E-03 4.28E+00 4.25E+00 4.27E+00 4.74E-03 4.28E+00 4.25E+00 4.26E+00 2.83E-03 4.27E+00 4.25E+00 4.27E+00 4.98E-03 4.29E+00 4.26E+00 4.00E+00 PASS 4.26E+00 5.20E-03 4.27E+00 4.24E+00 4.00E+00 PASS 4.26E+00 4.83E-03 4.27E+00 4.24E+00 4.00E+00 PASS An ISO 9001:2008 and DSCC Certified Company 137 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Positive Output Voltage 2 RL=open @ +5V (V) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 4.35E+00 4.30E+00 4.25E+00 4.20E+00 4.15E+00 4.10E+00 4.05E+00 4.00E+00 3.95E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.66. Plot of Positive Output Voltage 2 RL=open @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 138 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.66. Raw data for Positive Output Voltage 2 RL=open @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 2 RL=open @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.25E+00 4.26E+00 4.26E+00 4.27E+00 4.26E+00 4.25E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 24hr Anneal 60 4.26E+00 4.27E+00 4.27E+00 4.29E+00 4.27E+00 4.25E+00 4.26E+00 4.26E+00 4.27E+00 4.26E+00 4.27E+00 4.26E+00 168hr Anneal 70 4.28E+00 4.29E+00 4.28E+00 4.31E+00 4.29E+00 4.26E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.26E+00 4.25E+00 7.89E-03 4.28E+00 4.23E+00 4.26E+00 8.47E-03 4.28E+00 4.24E+00 4.27E+00 9.12E-03 4.30E+00 4.25E+00 4.29E+00 1.13E-02 4.32E+00 4.26E+00 4.25E+00 4.97E-03 4.26E+00 4.24E+00 4.00E+00 PASS 4.26E+00 5.03E-03 4.27E+00 4.24E+00 4.00E+00 PASS 4.26E+00 4.97E-03 4.27E+00 4.25E+00 4.00E+00 PASS 4.26E+00 4.98E-03 4.28E+00 4.25E+00 4.00E+00 PASS 0 4.24E+00 4.26E+00 4.26E+00 4.27E+00 4.25E+00 4.25E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 Total 10 4.25E+00 4.25E+00 4.25E+00 4.27E+00 4.25E+00 4.24E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.27E+00 4.26E+00 Dose (krad(Si)) 20 30 4.24E+00 4.24E+00 4.25E+00 4.26E+00 4.25E+00 4.25E+00 4.26E+00 4.27E+00 4.25E+00 4.25E+00 4.24E+00 4.24E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.26E+00 4.26E+00 4.25E+00 4.25E+00 4.27E+00 4.27E+00 4.26E+00 4.26E+00 4.26E+00 1.08E-02 4.29E+00 4.23E+00 4.26E+00 6.48E-03 4.27E+00 4.24E+00 4.25E+00 7.54E-03 4.27E+00 4.23E+00 4.26E+00 4.04E-03 4.27E+00 4.25E+00 4.00E+00 PASS 4.25E+00 4.66E-03 4.26E+00 4.23E+00 4.00E+00 PASS 4.25E+00 5.05E-03 4.26E+00 4.24E+00 4.00E+00 PASS An ISO 9001:2008 and DSCC Certified Company 139 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Positive Output Voltage 3 RL=open @ +5V (V) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 4.35E+00 4.30E+00 4.25E+00 4.20E+00 4.15E+00 4.10E+00 4.05E+00 4.00E+00 3.95E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.67. Plot of Positive Output Voltage 3 RL=open @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 140 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.67. Raw data for Positive Output Voltage 3 RL=open @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 3 RL=open @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.27E+00 4.28E+00 4.27E+00 4.28E+00 4.27E+00 4.26E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.28E+00 4.27E+00 24hr Anneal 60 4.28E+00 4.29E+00 4.28E+00 4.30E+00 4.29E+00 4.27E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 168hr Anneal 70 4.29E+00 4.31E+00 4.30E+00 4.31E+00 4.30E+00 4.28E+00 4.29E+00 4.28E+00 4.29E+00 4.28E+00 4.28E+00 4.27E+00 4.26E+00 5.72E-03 4.28E+00 4.25E+00 4.27E+00 6.06E-03 4.29E+00 4.26E+00 4.29E+00 8.20E-03 4.31E+00 4.27E+00 4.30E+00 5.81E-03 4.32E+00 4.28E+00 4.26E+00 4.66E-03 4.28E+00 4.25E+00 4.00E+00 PASS 4.27E+00 4.27E-03 4.28E+00 4.26E+00 4.00E+00 PASS 4.28E+00 4.60E-03 4.29E+00 4.26E+00 4.00E+00 PASS 4.28E+00 5.00E-03 4.30E+00 4.27E+00 4.00E+00 PASS 0 4.26E+00 4.27E+00 4.27E+00 4.28E+00 4.27E+00 4.27E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.27E+00 Total 10 4.26E+00 4.27E+00 4.26E+00 4.27E+00 4.27E+00 4.25E+00 4.26E+00 4.26E+00 4.27E+00 4.26E+00 4.28E+00 4.27E+00 Dose (krad(Si)) 20 30 4.26E+00 4.26E+00 4.26E+00 4.27E+00 4.26E+00 4.26E+00 4.27E+00 4.27E+00 4.26E+00 4.26E+00 4.25E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.27E+00 4.27E+00 4.26E+00 4.26E+00 4.28E+00 4.28E+00 4.27E+00 4.27E+00 4.27E+00 8.79E-03 4.29E+00 4.24E+00 4.27E+00 4.74E-03 4.28E+00 4.25E+00 4.26E+00 5.22E-03 4.28E+00 4.25E+00 4.28E+00 4.55E-03 4.29E+00 4.26E+00 4.00E+00 PASS 4.26E+00 5.15E-03 4.27E+00 4.24E+00 4.00E+00 PASS 4.26E+00 4.77E-03 4.27E+00 4.25E+00 4.00E+00 PASS An ISO 9001:2008 and DSCC Certified Company 141 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Positive Output Voltage 4 RL=open @ +5V (V) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 4.30E+00 4.25E+00 4.20E+00 4.15E+00 4.10E+00 4.05E+00 4.00E+00 3.95E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.68. Plot of Positive Output Voltage 4 RL=open @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 142 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.68. Raw data for Positive Output Voltage 4 RL=open @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 4 RL=open @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 4.26E+00 4.25E+00 4.25E+00 4.25E+00 4.26E+00 4.25E+00 4.26E+00 4.25E+00 4.25E+00 4.26E+00 4.25E+00 4.25E+00 24hr Anneal 60 4.27E+00 4.26E+00 4.26E+00 4.26E+00 4.27E+00 4.26E+00 4.26E+00 4.26E+00 4.25E+00 4.26E+00 4.25E+00 4.25E+00 168hr Anneal 70 4.28E+00 4.28E+00 4.27E+00 4.27E+00 4.29E+00 4.26E+00 4.27E+00 4.26E+00 4.26E+00 4.26E+00 4.25E+00 4.25E+00 4.25E+00 1.34E-03 4.25E+00 4.24E+00 4.25E+00 2.28E-03 4.26E+00 4.25E+00 4.26E+00 3.19E-03 4.27E+00 4.26E+00 4.28E+00 7.33E-03 4.30E+00 4.26E+00 4.25E+00 3.67E-03 4.26E+00 4.24E+00 4.00E+00 PASS 4.25E+00 4.16E-03 4.26E+00 4.24E+00 4.00E+00 PASS 4.26E+00 3.81E-03 4.27E+00 4.25E+00 4.00E+00 PASS 4.26E+00 3.36E-03 4.27E+00 4.25E+00 4.00E+00 PASS 0 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.26E+00 4.26E+00 4.25E+00 4.26E+00 4.25E+00 4.25E+00 Total 10 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.26E+00 4.24E+00 4.25E+00 4.24E+00 4.24E+00 4.25E+00 4.26E+00 4.25E+00 Dose (krad(Si)) 20 30 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.24E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.24E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 4.25E+00 2.74E-03 4.26E+00 4.24E+00 4.25E+00 3.70E-03 4.26E+00 4.24E+00 4.25E+00 1.92E-03 4.25E+00 4.24E+00 4.26E+00 2.79E-03 4.26E+00 4.25E+00 4.00E+00 PASS 4.25E+00 4.09E-03 4.26E+00 4.23E+00 4.00E+00 PASS 4.25E+00 4.09E-03 4.26E+00 4.24E+00 4.00E+00 PASS An ISO 9001:2008 and DSCC Certified Company 143 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Positive Output Voltage 1 RL=600 @ +5V (V) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 4.00E+00 3.50E+00 3.00E+00 2.50E+00 2.00E+00 1.50E+00 1.00E+00 5.00E-01 0.00E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.69. Plot of Positive Output Voltage 1 RL=600 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 144 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.69. Raw data for Positive Output Voltage 1 RL=600 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 1 RL=600 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 3.79E+00 3.80E+00 3.83E+00 3.80E+00 3.79E+00 3.79E+00 3.80E+00 3.80E+00 3.79E+00 3.82E+00 3.80E+00 3.80E+00 24hr Anneal 60 3.79E+00 3.80E+00 3.83E+00 3.80E+00 3.79E+00 3.79E+00 3.80E+00 3.80E+00 3.79E+00 3.82E+00 3.80E+00 3.80E+00 168hr Anneal 70 3.79E+00 3.80E+00 3.83E+00 3.80E+00 3.79E+00 3.79E+00 3.80E+00 3.80E+00 3.79E+00 3.82E+00 3.80E+00 3.80E+00 3.80E+00 1.65E-02 3.85E+00 3.76E+00 3.80E+00 1.65E-02 3.84E+00 3.75E+00 3.80E+00 1.65E-02 3.85E+00 3.75E+00 3.80E+00 1.63E-02 3.84E+00 3.75E+00 3.80E+00 1.18E-02 3.83E+00 3.77E+00 3.13E+00 PASS 3.80E+00 1.22E-02 3.83E+00 3.76E+00 3.00E+00 PASS 3.80E+00 1.23E-02 3.83E+00 3.76E+00 3.00E+00 PASS 3.80E+00 1.22E-02 3.83E+00 3.76E+00 3.00E+00 PASS 0 3.79E+00 3.80E+00 3.83E+00 3.80E+00 3.79E+00 3.79E+00 3.80E+00 3.80E+00 3.79E+00 3.82E+00 3.80E+00 3.80E+00 Total 10 3.79E+00 3.80E+00 3.83E+00 3.80E+00 3.79E+00 3.79E+00 3.81E+00 3.80E+00 3.79E+00 3.82E+00 3.80E+00 3.80E+00 Dose (krad(Si)) 20 30 3.79E+00 3.79E+00 3.80E+00 3.80E+00 3.83E+00 3.83E+00 3.80E+00 3.80E+00 3.79E+00 3.79E+00 3.79E+00 3.79E+00 3.81E+00 3.80E+00 3.80E+00 3.80E+00 3.79E+00 3.79E+00 3.82E+00 3.82E+00 3.80E+00 3.80E+00 3.80E+00 3.80E+00 3.80E+00 1.59E-02 3.84E+00 3.76E+00 3.80E+00 1.61E-02 3.85E+00 3.76E+00 3.80E+00 1.63E-02 3.85E+00 3.76E+00 3.80E+00 1.21E-02 3.83E+00 3.77E+00 3.40E+00 PASS 3.80E+00 1.21E-02 3.83E+00 3.77E+00 3.40E+00 PASS 3.80E+00 1.24E-02 3.83E+00 3.77E+00 3.20E+00 PASS An ISO 9001:2008 and DSCC Certified Company 145 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Positive Output Voltage 2 RL=600 @ +5V (V) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 4.50E+00 4.00E+00 3.50E+00 3.00E+00 2.50E+00 2.00E+00 1.50E+00 1.00E+00 5.00E-01 0.00E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.70. Plot of Positive Output Voltage 2 RL=600 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 146 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.70. Raw data for Positive Output Voltage 2 RL=600 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 2 RL=600 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 3.80E+00 3.82E+00 3.82E+00 3.83E+00 3.80E+00 3.80E+00 3.82E+00 3.81E+00 3.83E+00 3.81E+00 3.82E+00 3.83E+00 24hr Anneal 60 3.80E+00 3.82E+00 3.82E+00 3.83E+00 3.80E+00 3.80E+00 3.82E+00 3.81E+00 3.83E+00 3.81E+00 3.82E+00 3.83E+00 168hr Anneal 70 3.80E+00 3.82E+00 3.82E+00 3.83E+00 3.80E+00 3.80E+00 3.82E+00 3.81E+00 3.83E+00 3.81E+00 3.82E+00 3.83E+00 3.82E+00 1.34E-02 3.85E+00 3.78E+00 3.81E+00 1.32E-02 3.85E+00 3.78E+00 3.81E+00 1.34E-02 3.85E+00 3.78E+00 3.81E+00 1.36E-02 3.85E+00 3.78E+00 3.81E+00 1.16E-02 3.84E+00 3.78E+00 3.13E+00 PASS 3.81E+00 1.16E-02 3.84E+00 3.78E+00 3.00E+00 PASS 3.81E+00 1.12E-02 3.84E+00 3.78E+00 3.00E+00 PASS 3.81E+00 1.08E-02 3.84E+00 3.78E+00 3.00E+00 PASS 0 3.80E+00 3.82E+00 3.82E+00 3.83E+00 3.81E+00 3.80E+00 3.82E+00 3.82E+00 3.83E+00 3.81E+00 3.82E+00 3.83E+00 Total 10 3.80E+00 3.83E+00 3.82E+00 3.83E+00 3.81E+00 3.80E+00 3.82E+00 3.82E+00 3.83E+00 3.81E+00 3.82E+00 3.83E+00 Dose (krad(Si)) 20 30 3.80E+00 3.80E+00 3.83E+00 3.82E+00 3.82E+00 3.82E+00 3.83E+00 3.83E+00 3.81E+00 3.80E+00 3.80E+00 3.80E+00 3.82E+00 3.82E+00 3.82E+00 3.82E+00 3.83E+00 3.83E+00 3.81E+00 3.81E+00 3.82E+00 3.82E+00 3.83E+00 3.83E+00 3.82E+00 1.26E-02 3.85E+00 3.78E+00 3.82E+00 1.31E-02 3.85E+00 3.78E+00 3.82E+00 1.31E-02 3.85E+00 3.78E+00 3.81E+00 1.09E-02 3.84E+00 3.78E+00 3.40E+00 PASS 3.81E+00 1.08E-02 3.84E+00 3.78E+00 3.40E+00 PASS 3.81E+00 1.12E-02 3.84E+00 3.78E+00 3.20E+00 PASS An ISO 9001:2008 and DSCC Certified Company 147 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Positive Output Voltage 3 RL=600 @ +5V (V) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 4.00E+00 3.50E+00 3.00E+00 2.50E+00 2.00E+00 1.50E+00 1.00E+00 5.00E-01 0.00E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.71. Plot of Positive Output Voltage 3 RL=600 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 148 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.71. Raw data for Positive Output Voltage 3 RL=600 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 3 RL=600 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 3.78E+00 3.82E+00 3.81E+00 3.82E+00 3.79E+00 3.79E+00 3.81E+00 3.81E+00 3.82E+00 3.80E+00 3.81E+00 3.82E+00 24hr Anneal 60 3.79E+00 3.82E+00 3.81E+00 3.82E+00 3.79E+00 3.79E+00 3.81E+00 3.81E+00 3.82E+00 3.80E+00 3.81E+00 3.82E+00 168hr Anneal 70 3.79E+00 3.82E+00 3.81E+00 3.82E+00 3.79E+00 3.79E+00 3.81E+00 3.81E+00 3.82E+00 3.80E+00 3.81E+00 3.82E+00 3.81E+00 1.47E-02 3.85E+00 3.77E+00 3.80E+00 1.49E-02 3.84E+00 3.76E+00 3.80E+00 1.47E-02 3.85E+00 3.76E+00 3.80E+00 1.41E-02 3.84E+00 3.77E+00 3.80E+00 1.19E-02 3.84E+00 3.77E+00 3.13E+00 PASS 3.80E+00 1.20E-02 3.83E+00 3.77E+00 3.00E+00 PASS 3.80E+00 1.19E-02 3.84E+00 3.77E+00 3.00E+00 PASS 3.80E+00 1.15E-02 3.83E+00 3.77E+00 3.00E+00 PASS 0 3.79E+00 3.82E+00 3.81E+00 3.82E+00 3.80E+00 3.79E+00 3.81E+00 3.81E+00 3.82E+00 3.80E+00 3.81E+00 3.82E+00 Total 10 3.79E+00 3.82E+00 3.81E+00 3.82E+00 3.80E+00 3.79E+00 3.81E+00 3.81E+00 3.82E+00 3.80E+00 3.81E+00 3.82E+00 Dose (krad(Si)) 20 30 3.79E+00 3.79E+00 3.82E+00 3.82E+00 3.81E+00 3.81E+00 3.82E+00 3.82E+00 3.80E+00 3.80E+00 3.79E+00 3.79E+00 3.81E+00 3.81E+00 3.81E+00 3.81E+00 3.82E+00 3.82E+00 3.80E+00 3.80E+00 3.81E+00 3.81E+00 3.82E+00 3.82E+00 3.81E+00 1.36E-02 3.84E+00 3.77E+00 3.81E+00 1.40E-02 3.84E+00 3.77E+00 3.81E+00 1.46E-02 3.85E+00 3.77E+00 3.80E+00 1.15E-02 3.84E+00 3.77E+00 3.40E+00 PASS 3.81E+00 1.15E-02 3.84E+00 3.77E+00 3.40E+00 PASS 3.81E+00 1.15E-02 3.84E+00 3.77E+00 3.20E+00 PASS An ISO 9001:2008 and DSCC Certified Company 149 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Positive Output Voltage 4 RL=600 @ +5V (V) TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Ps90%/90% (-KTL) Biased 4.50E+00 4.00E+00 3.50E+00 3.00E+00 2.50E+00 2.00E+00 1.50E+00 1.00E+00 5.00E-01 0.00E+00 0 10 20 30 40 Total Dose (krad(Si)) 50 24hr 60 Anneal 168hr 70 Figure 5.72. Plot of Positive Output Voltage 4 RL=600 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 150 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.72. Raw data for Positive Output Voltage 4 RL=600 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage 4 RL=600 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 50 3.80E+00 3.81E+00 3.83E+00 3.81E+00 3.80E+00 3.80E+00 3.81E+00 3.81E+00 3.80E+00 3.83E+00 3.81E+00 3.81E+00 24hr Anneal 60 3.80E+00 3.81E+00 3.84E+00 3.81E+00 3.80E+00 3.80E+00 3.81E+00 3.81E+00 3.80E+00 3.83E+00 3.81E+00 3.81E+00 168hr Anneal 70 3.80E+00 3.81E+00 3.83E+00 3.81E+00 3.80E+00 3.80E+00 3.81E+00 3.81E+00 3.80E+00 3.83E+00 3.81E+00 3.81E+00 3.81E+00 1.53E-02 3.85E+00 3.77E+00 3.81E+00 1.54E-02 3.85E+00 3.77E+00 3.81E+00 1.54E-02 3.85E+00 3.77E+00 3.81E+00 1.54E-02 3.85E+00 3.77E+00 3.81E+00 1.13E-02 3.84E+00 3.78E+00 3.13E+00 PASS 3.81E+00 1.19E-02 3.84E+00 3.77E+00 3.00E+00 PASS 3.81E+00 1.13E-02 3.84E+00 3.78E+00 3.00E+00 PASS 3.81E+00 1.19E-02 3.84E+00 3.77E+00 3.00E+00 PASS 0 3.80E+00 3.81E+00 3.84E+00 3.81E+00 3.80E+00 3.80E+00 3.81E+00 3.81E+00 3.80E+00 3.83E+00 3.81E+00 3.81E+00 Total 10 3.80E+00 3.81E+00 3.84E+00 3.81E+00 3.80E+00 3.80E+00 3.81E+00 3.81E+00 3.80E+00 3.83E+00 3.81E+00 3.81E+00 Dose (krad(Si)) 20 30 3.80E+00 3.80E+00 3.81E+00 3.81E+00 3.84E+00 3.84E+00 3.81E+00 3.81E+00 3.80E+00 3.80E+00 3.80E+00 3.80E+00 3.81E+00 3.81E+00 3.81E+00 3.81E+00 3.80E+00 3.80E+00 3.83E+00 3.83E+00 3.81E+00 3.81E+00 3.81E+00 3.81E+00 3.81E+00 1.53E-02 3.85E+00 3.77E+00 3.81E+00 1.53E-02 3.85E+00 3.77E+00 3.81E+00 1.51E-02 3.85E+00 3.77E+00 3.81E+00 1.11E-02 3.84E+00 3.78E+00 3.40E+00 PASS 3.81E+00 1.13E-02 3.84E+00 3.78E+00 3.40E+00 PASS 3.81E+00 1.17E-02 3.84E+00 3.78E+00 3.20E+00 PASS An ISO 9001:2008 and DSCC Certified Company 151 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 1 RL=open @ +5V (V) 4.50E-02 4.00E-02 3.50E-02 3.00E-02 2.50E-02 2.00E-02 1.50E-02 1.00E-02 5.00E-03 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.73. Plot of Output Voltage Low 1 RL=open @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 152 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.73. Raw data for Output Voltage Low 1 RL=open @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 1 RL=open @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 1.38E-02 1.41E-02 1.40E-02 1.41E-02 1.38E-02 1.38E-02 1.41E-02 1.39E-02 1.41E-02 1.43E-02 1.37E-02 1.38E-02 24hr Anneal 60 1.39E-02 1.40E-02 1.41E-02 1.40E-02 1.39E-02 1.41E-02 1.42E-02 1.40E-02 1.40E-02 1.42E-02 1.38E-02 1.38E-02 168hr Anneal 70 1.39E-02 1.39E-02 1.40E-02 1.39E-02 1.37E-02 1.38E-02 1.40E-02 1.38E-02 1.39E-02 1.40E-02 1.37E-02 1.37E-02 1.40E-02 5.48E-05 1.41E-02 1.38E-02 1.40E-02 1.52E-04 1.44E-02 1.35E-02 1.40E-02 8.37E-05 1.42E-02 1.38E-02 1.39E-02 1.10E-04 1.42E-02 1.36E-02 1.39E-02 1.79E-04 1.44E-02 1.34E-02 3.33E-02 PASS 1.40E-02 1.95E-04 1.46E-02 1.35E-02 4.00E-02 PASS 1.41E-02 1.00E-04 1.44E-02 1.38E-02 4.00E-02 PASS 1.39E-02 1.00E-04 1.42E-02 1.36E-02 4.00E-02 PASS 0 1.36E-02 1.38E-02 1.38E-02 1.38E-02 1.37E-02 1.38E-02 1.39E-02 1.36E-02 1.37E-02 1.40E-02 1.37E-02 1.38E-02 Total 10 1.37E-02 1.38E-02 1.40E-02 1.38E-02 1.38E-02 1.37E-02 1.39E-02 1.37E-02 1.39E-02 1.41E-02 1.39E-02 1.38E-02 Dose (krad(Si)) 20 30 1.38E-02 1.39E-02 1.39E-02 1.40E-02 1.40E-02 1.40E-02 1.39E-02 1.40E-02 1.38E-02 1.39E-02 1.37E-02 1.38E-02 1.40E-02 1.41E-02 1.38E-02 1.37E-02 1.40E-02 1.39E-02 1.42E-02 1.41E-02 1.39E-02 1.37E-02 1.39E-02 1.38E-02 1.37E-02 8.94E-05 1.40E-02 1.35E-02 1.38E-02 1.10E-04 1.41E-02 1.35E-02 1.39E-02 8.37E-05 1.41E-02 1.37E-02 1.38E-02 1.58E-04 1.42E-02 1.34E-02 2.50E-02 PASS 1.39E-02 1.67E-04 1.43E-02 1.34E-02 2.50E-02 PASS 1.39E-02 1.95E-04 1.45E-02 1.34E-02 3.00E-02 PASS An ISO 9001:2008 and DSCC Certified Company 153 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 2 RL=open @ +5V (V) 4.50E-02 4.00E-02 3.50E-02 3.00E-02 2.50E-02 2.00E-02 1.50E-02 1.00E-02 5.00E-03 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.74. Plot of Output Voltage Low 2 RL=open @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 154 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.74. Raw data for Output Voltage Low 2 RL=open @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 2 RL=open @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 1.38E-02 1.41E-02 1.39E-02 1.40E-02 1.37E-02 1.37E-02 1.39E-02 1.40E-02 1.41E-02 1.38E-02 1.38E-02 1.39E-02 24hr Anneal 60 1.38E-02 1.42E-02 1.40E-02 1.39E-02 1.38E-02 1.39E-02 1.40E-02 1.42E-02 1.42E-02 1.40E-02 1.39E-02 1.39E-02 168hr Anneal 70 1.38E-02 1.41E-02 1.39E-02 1.40E-02 1.37E-02 1.37E-02 1.39E-02 1.40E-02 1.42E-02 1.37E-02 1.38E-02 1.38E-02 1.39E-02 1.48E-04 1.43E-02 1.35E-02 1.39E-02 1.58E-04 1.43E-02 1.35E-02 1.39E-02 1.67E-04 1.44E-02 1.35E-02 1.39E-02 1.58E-04 1.43E-02 1.35E-02 1.39E-02 1.82E-04 1.44E-02 1.34E-02 3.33E-02 PASS 1.39E-02 1.58E-04 1.43E-02 1.35E-02 4.00E-02 PASS 1.41E-02 1.34E-04 1.44E-02 1.37E-02 4.00E-02 PASS 1.39E-02 2.12E-04 1.45E-02 1.33E-02 4.00E-02 PASS 0 1.35E-02 1.39E-02 1.38E-02 1.37E-02 1.34E-02 1.36E-02 1.38E-02 1.38E-02 1.40E-02 1.36E-02 1.37E-02 1.39E-02 Total 10 1.36E-02 1.40E-02 1.38E-02 1.38E-02 1.36E-02 1.35E-02 1.39E-02 1.39E-02 1.40E-02 1.38E-02 1.38E-02 1.39E-02 Dose (krad(Si)) 20 30 1.37E-02 1.37E-02 1.41E-02 1.41E-02 1.39E-02 1.39E-02 1.39E-02 1.39E-02 1.36E-02 1.38E-02 1.35E-02 1.38E-02 1.40E-02 1.40E-02 1.40E-02 1.41E-02 1.40E-02 1.41E-02 1.37E-02 1.37E-02 1.38E-02 1.38E-02 1.40E-02 1.39E-02 1.37E-02 2.07E-04 1.42E-02 1.31E-02 1.38E-02 1.67E-04 1.42E-02 1.33E-02 1.38E-02 1.95E-04 1.44E-02 1.33E-02 1.38E-02 1.67E-04 1.42E-02 1.33E-02 2.50E-02 PASS 1.38E-02 1.92E-04 1.43E-02 1.33E-02 2.50E-02 PASS 1.38E-02 2.30E-04 1.45E-02 1.32E-02 3.00E-02 PASS An ISO 9001:2008 and DSCC Certified Company 155 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 3 RL=open @ +5V (V) 4.50E-02 4.00E-02 3.50E-02 3.00E-02 2.50E-02 2.00E-02 1.50E-02 1.00E-02 5.00E-03 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.75. Plot of Output Voltage Low 3 RL=open @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 156 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.75. Raw data for Output Voltage Low 3 RL=open @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 3 RL=open @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 1.38E-02 1.41E-02 1.41E-02 1.39E-02 1.38E-02 1.39E-02 1.40E-02 1.42E-02 1.41E-02 1.40E-02 1.38E-02 1.40E-02 24hr Anneal 60 1.39E-02 1.42E-02 1.40E-02 1.42E-02 1.39E-02 1.39E-02 1.41E-02 1.42E-02 1.41E-02 1.39E-02 1.39E-02 1.39E-02 168hr Anneal 70 1.39E-02 1.43E-02 1.38E-02 1.39E-02 1.38E-02 1.38E-02 1.41E-02 1.40E-02 1.40E-02 1.38E-02 1.39E-02 1.39E-02 1.39E-02 1.87E-04 1.44E-02 1.34E-02 1.39E-02 1.52E-04 1.44E-02 1.35E-02 1.40E-02 1.52E-04 1.45E-02 1.36E-02 1.39E-02 2.07E-04 1.45E-02 1.34E-02 1.40E-02 2.00E-04 1.45E-02 1.35E-02 3.33E-02 PASS 1.40E-02 1.14E-04 1.44E-02 1.37E-02 4.00E-02 PASS 1.40E-02 1.34E-04 1.44E-02 1.37E-02 4.00E-02 PASS 1.39E-02 1.34E-04 1.43E-02 1.36E-02 4.00E-02 PASS 0 1.35E-02 1.40E-02 1.38E-02 1.40E-02 1.35E-02 1.37E-02 1.40E-02 1.39E-02 1.39E-02 1.36E-02 1.38E-02 1.40E-02 Total 10 1.37E-02 1.41E-02 1.39E-02 1.39E-02 1.37E-02 1.37E-02 1.40E-02 1.40E-02 1.40E-02 1.37E-02 1.40E-02 1.41E-02 Dose (krad(Si)) 20 30 1.38E-02 1.37E-02 1.40E-02 1.41E-02 1.38E-02 1.40E-02 1.40E-02 1.40E-02 1.38E-02 1.37E-02 1.37E-02 1.37E-02 1.40E-02 1.41E-02 1.42E-02 1.42E-02 1.40E-02 1.41E-02 1.36E-02 1.39E-02 1.38E-02 1.40E-02 1.39E-02 1.40E-02 1.38E-02 2.51E-04 1.44E-02 1.31E-02 1.39E-02 1.67E-04 1.43E-02 1.34E-02 1.39E-02 1.10E-04 1.42E-02 1.36E-02 1.38E-02 1.64E-04 1.43E-02 1.34E-02 2.50E-02 PASS 1.39E-02 1.64E-04 1.43E-02 1.34E-02 2.50E-02 PASS 1.39E-02 2.45E-04 1.46E-02 1.32E-02 3.00E-02 PASS An ISO 9001:2008 and DSCC Certified Company 157 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 4 RL=open @ +5V (V) 4.50E-02 4.00E-02 3.50E-02 3.00E-02 2.50E-02 2.00E-02 1.50E-02 1.00E-02 5.00E-03 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.76. Plot of Output Voltage Low 4 RL=open @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 158 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.76. Raw data for Output Voltage Low 4 RL=open @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 4 RL=open @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 1.39E-02 1.39E-02 1.40E-02 1.39E-02 1.38E-02 1.39E-02 1.39E-02 1.39E-02 1.40E-02 1.42E-02 1.37E-02 1.36E-02 24hr Anneal 60 1.38E-02 1.39E-02 1.40E-02 1.40E-02 1.38E-02 1.39E-02 1.39E-02 1.38E-02 1.38E-02 1.42E-02 1.37E-02 1.37E-02 168hr Anneal 70 1.37E-02 1.40E-02 1.40E-02 1.40E-02 1.37E-02 1.38E-02 1.40E-02 1.37E-02 1.38E-02 1.41E-02 1.38E-02 1.37E-02 1.39E-02 2.30E-04 1.45E-02 1.32E-02 1.39E-02 7.07E-05 1.41E-02 1.37E-02 1.39E-02 1.00E-04 1.42E-02 1.36E-02 1.39E-02 1.64E-04 1.43E-02 1.34E-02 1.38E-02 2.61E-04 1.46E-02 1.31E-02 3.33E-02 PASS 1.40E-02 1.30E-04 1.43E-02 1.36E-02 4.00E-02 PASS 1.39E-02 1.64E-04 1.44E-02 1.35E-02 4.00E-02 PASS 1.39E-02 1.64E-04 1.43E-02 1.34E-02 4.00E-02 PASS 0 1.34E-02 1.36E-02 1.38E-02 1.38E-02 1.36E-02 1.37E-02 1.37E-02 1.36E-02 1.36E-02 1.40E-02 1.37E-02 1.36E-02 Total 10 1.37E-02 1.36E-02 1.39E-02 1.37E-02 1.37E-02 1.36E-02 1.38E-02 1.36E-02 1.36E-02 1.40E-02 1.36E-02 1.37E-02 Dose (krad(Si)) 20 30 1.37E-02 1.37E-02 1.38E-02 1.39E-02 1.41E-02 1.42E-02 1.38E-02 1.39E-02 1.38E-02 1.36E-02 1.37E-02 1.38E-02 1.38E-02 1.40E-02 1.37E-02 1.36E-02 1.37E-02 1.36E-02 1.41E-02 1.42E-02 1.37E-02 1.37E-02 1.37E-02 1.38E-02 1.36E-02 1.67E-04 1.41E-02 1.32E-02 1.37E-02 1.10E-04 1.40E-02 1.34E-02 1.38E-02 1.52E-04 1.43E-02 1.34E-02 1.37E-02 1.64E-04 1.42E-02 1.33E-02 2.50E-02 PASS 1.37E-02 1.79E-04 1.42E-02 1.32E-02 2.50E-02 PASS 1.38E-02 1.73E-04 1.43E-02 1.33E-02 3.00E-02 PASS An ISO 9001:2008 and DSCC Certified Company 159 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 1 RL=600 @ +5V (V) 1.20E-02 1.00E-02 8.00E-03 6.00E-03 4.00E-03 2.00E-03 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.77. Plot of Output Voltage Low 1 RL=600 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 160 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.77. Raw data for Output Voltage Low 1 RL=600 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 1 RL=600 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 5.00E-03 5.10E-03 5.30E-03 5.10E-03 5.20E-03 5.20E-03 5.20E-03 5.20E-03 5.30E-03 5.30E-03 5.20E-03 5.20E-03 24hr Anneal 60 5.00E-03 5.10E-03 5.30E-03 5.30E-03 5.00E-03 5.10E-03 5.20E-03 5.20E-03 5.10E-03 5.30E-03 5.20E-03 5.20E-03 168hr Anneal 70 5.00E-03 5.10E-03 5.10E-03 4.90E-03 4.90E-03 5.00E-03 5.20E-03 5.30E-03 5.10E-03 5.30E-03 5.30E-03 5.20E-03 5.28E-03 1.48E-04 5.69E-03 4.87E-03 5.14E-03 1.14E-04 5.45E-03 4.83E-03 5.14E-03 1.52E-04 5.56E-03 4.72E-03 5.00E-03 1.00E-04 5.27E-03 4.73E-03 5.28E-03 8.37E-05 5.51E-03 5.05E-03 1.00E-02 PASS 5.24E-03 5.48E-05 5.39E-03 5.09E-03 1.00E-02 PASS 5.18E-03 8.37E-05 5.41E-03 4.95E-03 1.00E-02 PASS 5.18E-03 1.30E-04 5.54E-03 4.82E-03 1.00E-02 PASS 0 5.10E-03 5.30E-03 5.40E-03 5.20E-03 5.30E-03 5.10E-03 5.10E-03 5.30E-03 5.10E-03 5.20E-03 5.20E-03 5.20E-03 Total 10 5.10E-03 5.20E-03 5.40E-03 5.40E-03 5.00E-03 5.30E-03 5.40E-03 5.30E-03 5.20E-03 5.50E-03 5.40E-03 5.20E-03 Dose (krad(Si)) 20 30 5.20E-03 5.10E-03 5.30E-03 5.30E-03 5.50E-03 5.50E-03 5.30E-03 5.30E-03 5.40E-03 5.20E-03 5.30E-03 5.20E-03 5.50E-03 5.30E-03 5.40E-03 5.30E-03 5.30E-03 5.20E-03 5.50E-03 5.40E-03 5.30E-03 5.20E-03 5.30E-03 5.10E-03 5.26E-03 1.14E-04 5.57E-03 4.95E-03 5.22E-03 1.79E-04 5.71E-03 4.73E-03 5.34E-03 1.14E-04 5.65E-03 5.03E-03 5.16E-03 8.94E-05 5.41E-03 4.91E-03 1.00E-02 PASS 5.34E-03 1.14E-04 5.65E-03 5.03E-03 1.00E-02 PASS 5.40E-03 1.00E-04 5.67E-03 5.13E-03 1.00E-02 PASS An ISO 9001:2008 and DSCC Certified Company 161 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 2 RL=600 @ +5V (V) 1.20E-02 1.00E-02 8.00E-03 6.00E-03 4.00E-03 2.00E-03 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.78. Plot of Output Voltage Low 2 RL=600 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 162 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.78. Raw data for Output Voltage Low 2 RL=600 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 2 RL=600 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 5.40E-03 5.50E-03 5.40E-03 5.30E-03 5.50E-03 5.40E-03 5.60E-03 5.60E-03 5.50E-03 5.30E-03 5.40E-03 5.60E-03 24hr Anneal 60 5.40E-03 5.50E-03 5.40E-03 5.30E-03 5.40E-03 5.30E-03 5.50E-03 5.40E-03 5.50E-03 5.30E-03 5.50E-03 5.60E-03 168hr Anneal 70 5.10E-03 5.30E-03 5.10E-03 5.20E-03 5.10E-03 5.30E-03 5.40E-03 5.40E-03 5.40E-03 5.40E-03 5.40E-03 5.60E-03 5.52E-03 8.37E-05 5.75E-03 5.29E-03 5.42E-03 8.37E-05 5.65E-03 5.19E-03 5.40E-03 7.07E-05 5.59E-03 5.21E-03 5.16E-03 8.94E-05 5.41E-03 4.91E-03 5.50E-03 7.07E-05 5.69E-03 5.31E-03 1.00E-02 PASS 5.48E-03 1.30E-04 5.84E-03 5.12E-03 1.00E-02 PASS 5.40E-03 1.00E-04 5.67E-03 5.13E-03 1.00E-02 PASS 5.38E-03 4.47E-05 5.50E-03 5.26E-03 1.00E-02 PASS 0 5.40E-03 5.60E-03 5.50E-03 5.50E-03 5.40E-03 5.30E-03 5.30E-03 5.40E-03 5.50E-03 5.40E-03 5.50E-03 5.50E-03 Total 10 5.30E-03 5.80E-03 5.50E-03 5.50E-03 5.40E-03 5.50E-03 5.50E-03 5.50E-03 5.70E-03 5.40E-03 5.50E-03 5.70E-03 Dose (krad(Si)) 20 30 5.50E-03 5.50E-03 5.60E-03 5.60E-03 5.60E-03 5.60E-03 5.50E-03 5.40E-03 5.50E-03 5.50E-03 5.40E-03 5.50E-03 5.60E-03 5.50E-03 5.60E-03 5.50E-03 5.70E-03 5.60E-03 5.60E-03 5.40E-03 5.50E-03 5.50E-03 5.70E-03 5.60E-03 5.48E-03 8.37E-05 5.71E-03 5.25E-03 5.50E-03 1.87E-04 6.01E-03 4.99E-03 5.54E-03 5.48E-05 5.69E-03 5.39E-03 5.38E-03 8.37E-05 5.61E-03 5.15E-03 1.00E-02 PASS 5.52E-03 1.10E-04 5.82E-03 5.22E-03 1.00E-02 PASS 5.58E-03 1.10E-04 5.88E-03 5.28E-03 1.00E-02 PASS An ISO 9001:2008 and DSCC Certified Company 163 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 3 RL=600 @ +5V (V) 1.20E-02 1.00E-02 8.00E-03 6.00E-03 4.00E-03 2.00E-03 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.79. Plot of Output Voltage Low 3 RL=600 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 164 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.79. Raw data for Output Voltage Low 3 RL=600 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 3 RL=600 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 5.10E-03 5.10E-03 5.20E-03 5.20E-03 5.20E-03 5.10E-03 5.30E-03 5.20E-03 5.40E-03 5.30E-03 5.30E-03 5.40E-03 24hr Anneal 60 5.10E-03 5.30E-03 5.20E-03 5.30E-03 5.20E-03 5.10E-03 5.20E-03 5.20E-03 5.30E-03 5.20E-03 5.20E-03 5.40E-03 168hr Anneal 70 4.90E-03 5.10E-03 5.10E-03 5.00E-03 5.00E-03 5.10E-03 5.30E-03 5.20E-03 5.30E-03 5.10E-03 5.30E-03 5.40E-03 5.28E-03 1.10E-04 5.58E-03 4.98E-03 5.16E-03 5.48E-05 5.31E-03 5.01E-03 5.22E-03 8.37E-05 5.45E-03 4.99E-03 5.02E-03 8.37E-05 5.25E-03 4.79E-03 5.28E-03 8.37E-05 5.51E-03 5.05E-03 1.00E-02 PASS 5.26E-03 1.14E-04 5.57E-03 4.95E-03 1.00E-02 PASS 5.20E-03 7.07E-05 5.39E-03 5.01E-03 1.00E-02 PASS 5.20E-03 1.00E-04 5.47E-03 4.93E-03 1.00E-02 PASS 0 5.20E-03 5.40E-03 5.20E-03 5.30E-03 5.30E-03 5.10E-03 5.30E-03 5.30E-03 5.40E-03 5.30E-03 5.20E-03 5.40E-03 Total 10 5.10E-03 5.50E-03 5.50E-03 5.50E-03 5.40E-03 5.20E-03 5.40E-03 5.20E-03 5.50E-03 5.20E-03 5.40E-03 5.40E-03 Dose (krad(Si)) 20 30 5.10E-03 5.10E-03 5.50E-03 5.40E-03 5.30E-03 5.30E-03 5.40E-03 5.30E-03 5.30E-03 5.30E-03 5.10E-03 5.20E-03 5.40E-03 5.30E-03 5.30E-03 5.30E-03 5.40E-03 5.40E-03 5.20E-03 5.20E-03 5.40E-03 5.40E-03 5.40E-03 5.40E-03 5.28E-03 8.37E-05 5.51E-03 5.05E-03 5.40E-03 1.73E-04 5.87E-03 4.93E-03 5.32E-03 1.48E-04 5.73E-03 4.91E-03 5.28E-03 1.10E-04 5.58E-03 4.98E-03 1.00E-02 PASS 5.30E-03 1.41E-04 5.69E-03 4.91E-03 1.00E-02 PASS 5.28E-03 1.30E-04 5.64E-03 4.92E-03 1.00E-02 PASS An ISO 9001:2008 and DSCC Certified Company 165 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 4 RL=600 @ +5V (V) 1.20E-02 1.00E-02 8.00E-03 6.00E-03 4.00E-03 2.00E-03 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.80. Plot of Output Voltage Low 4 RL=600 @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 166 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.80. Raw data for Output Voltage Low 4 RL=600 @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 4 RL=600 @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 5.10E-03 5.50E-03 5.70E-03 5.50E-03 5.20E-03 5.40E-03 5.50E-03 5.60E-03 5.40E-03 5.50E-03 5.50E-03 5.30E-03 24hr Anneal 60 5.20E-03 5.40E-03 5.60E-03 5.40E-03 5.30E-03 5.30E-03 5.40E-03 5.40E-03 5.40E-03 5.50E-03 5.50E-03 5.50E-03 168hr Anneal 70 5.10E-03 5.30E-03 5.50E-03 5.20E-03 5.20E-03 5.30E-03 5.40E-03 5.40E-03 5.40E-03 5.50E-03 5.50E-03 5.50E-03 5.50E-03 1.22E-04 5.84E-03 5.16E-03 5.40E-03 2.45E-04 6.07E-03 4.73E-03 5.38E-03 1.48E-04 5.79E-03 4.97E-03 5.26E-03 1.52E-04 5.68E-03 4.84E-03 5.52E-03 4.47E-05 5.64E-03 5.40E-03 1.00E-02 PASS 5.48E-03 8.37E-05 5.71E-03 5.25E-03 1.00E-02 PASS 5.40E-03 7.07E-05 5.59E-03 5.21E-03 1.00E-02 PASS 5.40E-03 7.07E-05 5.59E-03 5.21E-03 1.00E-02 PASS 0 5.40E-03 5.60E-03 5.80E-03 5.60E-03 5.50E-03 5.40E-03 5.50E-03 5.40E-03 5.40E-03 5.50E-03 5.60E-03 5.40E-03 Total 10 5.30E-03 5.40E-03 5.70E-03 5.50E-03 5.40E-03 5.50E-03 5.50E-03 5.60E-03 5.50E-03 5.70E-03 5.60E-03 5.50E-03 Dose (krad(Si)) 20 30 5.40E-03 5.50E-03 5.50E-03 5.40E-03 5.80E-03 5.70E-03 5.50E-03 5.40E-03 5.40E-03 5.50E-03 5.60E-03 5.50E-03 5.50E-03 5.50E-03 5.40E-03 5.50E-03 5.50E-03 5.50E-03 5.70E-03 5.60E-03 5.40E-03 5.60E-03 5.50E-03 5.40E-03 5.58E-03 1.48E-04 5.99E-03 5.17E-03 5.46E-03 1.52E-04 5.88E-03 5.04E-03 5.52E-03 1.64E-04 5.97E-03 5.07E-03 5.44E-03 5.48E-05 5.59E-03 5.29E-03 1.00E-02 PASS 5.56E-03 8.94E-05 5.81E-03 5.31E-03 1.00E-02 PASS 5.54E-03 1.14E-04 5.85E-03 5.23E-03 1.00E-02 PASS An ISO 9001:2008 and DSCC Certified Company 167 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 1 IL=1mA @ +5V (V) 1.20E+00 1.00E+00 8.00E-01 6.00E-01 4.00E-01 2.00E-01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.81. Plot of Output Voltage Low 1 IL=1mA @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 168 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.81. Raw data for Output Voltage Low 1 IL=1mA @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 1 IL=1mA @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 2.51E-01 2.45E-01 2.52E-01 2.51E-01 2.47E-01 2.48E-01 2.51E-01 2.49E-01 2.50E-01 2.45E-01 2.46E-01 2.47E-01 24hr Anneal 60 2.54E-01 2.49E-01 2.55E-01 2.54E-01 2.50E-01 2.51E-01 2.53E-01 2.50E-01 2.53E-01 2.47E-01 2.47E-01 2.47E-01 168hr Anneal 70 2.58E-01 2.53E-01 2.57E-01 2.57E-01 2.54E-01 2.52E-01 2.54E-01 2.51E-01 2.54E-01 2.49E-01 2.47E-01 2.47E-01 2.48E-01 2.97E-03 2.56E-01 2.39E-01 2.49E-01 3.03E-03 2.58E-01 2.41E-01 2.52E-01 2.70E-03 2.60E-01 2.45E-01 2.56E-01 2.17E-03 2.62E-01 2.50E-01 2.48E-01 2.17E-03 2.54E-01 2.42E-01 8.67E-01 PASS 2.49E-01 2.30E-03 2.55E-01 2.42E-01 1.00E+00 PASS 2.51E-01 2.49E-03 2.58E-01 2.44E-01 1.00E+00 PASS 2.52E-01 2.12E-03 2.58E-01 2.46E-01 1.00E+00 PASS 0 2.49E-01 2.44E-01 2.52E-01 2.50E-01 2.44E-01 2.49E-01 2.51E-01 2.49E-01 2.52E-01 2.47E-01 2.47E-01 2.47E-01 Total Dose (krad(Si)) 10 20 30 2.49E-01 2.48E-01 2.49E-01 2.46E-01 2.44E-01 2.44E-01 2.51E-01 2.50E-01 2.51E-01 2.49E-01 2.49E-01 2.49E-01 2.46E-01 2.45E-01 2.45E-01 2.46E-01 2.46E-01 2.47E-01 2.49E-01 2.49E-01 2.50E-01 2.45E-01 2.46E-01 2.47E-01 2.48E-01 2.49E-01 2.50E-01 2.43E-01 2.44E-01 2.45E-01 2.47E-01 2.46E-01 2.47E-01 2.47E-01 2.47E-01 2.46E-01 2.48E-01 3.63E-03 2.58E-01 2.38E-01 2.48E-01 2.17E-03 2.54E-01 2.42E-01 2.47E-01 2.59E-03 2.54E-01 2.40E-01 2.50E-01 1.95E-03 2.55E-01 2.44E-01 3.50E-01 PASS 2.46E-01 2.39E-03 2.53E-01 2.40E-01 6.00E-01 PASS 2.47E-01 2.17E-03 2.53E-01 2.41E-01 8.00E-01 PASS An ISO 9001:2008 and DSCC Certified Company 169 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 2 IL=1mA @ +5V (V) 1.20E+00 1.00E+00 8.00E-01 6.00E-01 4.00E-01 2.00E-01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.82. Plot of Output Voltage Low 2 IL=1mA @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 170 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.82. Raw data for Output Voltage Low 2 IL=1mA @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 2 IL=1mA @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 2.43E-01 2.45E-01 2.45E-01 2.48E-01 2.42E-01 2.44E-01 2.43E-01 2.44E-01 2.41E-01 2.44E-01 2.44E-01 2.40E-01 24hr Anneal 60 2.46E-01 2.48E-01 2.48E-01 2.51E-01 2.45E-01 2.46E-01 2.44E-01 2.46E-01 2.43E-01 2.46E-01 2.44E-01 2.41E-01 168hr Anneal 70 2.49E-01 2.50E-01 2.50E-01 2.54E-01 2.48E-01 2.46E-01 2.45E-01 2.47E-01 2.43E-01 2.46E-01 2.44E-01 2.41E-01 2.43E-01 2.68E-03 2.50E-01 2.35E-01 2.45E-01 2.30E-03 2.51E-01 2.38E-01 2.48E-01 2.30E-03 2.54E-01 2.41E-01 2.50E-01 2.28E-03 2.56E-01 2.44E-01 2.42E-01 8.94E-04 2.45E-01 2.40E-01 8.67E-01 PASS 2.43E-01 1.30E-03 2.47E-01 2.40E-01 1.00E+00 PASS 2.45E-01 1.41E-03 2.49E-01 2.41E-01 1.00E+00 PASS 2.45E-01 1.52E-03 2.50E-01 2.41E-01 1.00E+00 PASS 0 2.40E-01 2.44E-01 2.44E-01 2.47E-01 2.40E-01 2.44E-01 2.44E-01 2.45E-01 2.41E-01 2.44E-01 2.45E-01 2.42E-01 Total Dose (krad(Si)) 10 20 30 2.41E-01 2.40E-01 2.41E-01 2.43E-01 2.43E-01 2.43E-01 2.43E-01 2.42E-01 2.43E-01 2.46E-01 2.46E-01 2.47E-01 2.41E-01 2.39E-01 2.40E-01 2.41E-01 2.42E-01 2.43E-01 2.40E-01 2.41E-01 2.42E-01 2.41E-01 2.43E-01 2.43E-01 2.39E-01 2.39E-01 2.41E-01 2.42E-01 2.42E-01 2.43E-01 2.46E-01 2.45E-01 2.45E-01 2.42E-01 2.42E-01 2.41E-01 2.43E-01 3.00E-03 2.51E-01 2.35E-01 2.43E-01 2.05E-03 2.48E-01 2.37E-01 2.42E-01 2.74E-03 2.50E-01 2.34E-01 2.44E-01 1.52E-03 2.48E-01 2.39E-01 3.50E-01 PASS 2.41E-01 1.14E-03 2.44E-01 2.37E-01 6.00E-01 PASS 2.41E-01 1.52E-03 2.46E-01 2.37E-01 8.00E-01 PASS An ISO 9001:2008 and DSCC Certified Company 171 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 3 IL=1mA @ +5V (V) 1.20E+00 1.00E+00 8.00E-01 6.00E-01 4.00E-01 2.00E-01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.83. Plot of Output Voltage Low 3 IL=1mA @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 172 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.83. Raw data for Output Voltage Low 3 IL=1mA @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 3 IL=1mA @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 2.49E-01 2.50E-01 2.48E-01 2.51E-01 2.48E-01 2.49E-01 2.48E-01 2.49E-01 2.46E-01 2.49E-01 2.49E-01 2.45E-01 24hr Anneal 60 2.53E-01 2.53E-01 2.51E-01 2.54E-01 2.51E-01 2.51E-01 2.49E-01 2.51E-01 2.47E-01 2.51E-01 2.50E-01 2.46E-01 168hr Anneal 70 2.56E-01 2.56E-01 2.54E-01 2.58E-01 2.55E-01 2.52E-01 2.51E-01 2.52E-01 2.49E-01 2.52E-01 2.50E-01 2.46E-01 2.47E-01 1.92E-03 2.52E-01 2.42E-01 2.49E-01 1.30E-03 2.53E-01 2.46E-01 2.52E-01 1.34E-03 2.56E-01 2.49E-01 2.56E-01 1.48E-03 2.60E-01 2.52E-01 2.47E-01 1.64E-03 2.51E-01 2.42E-01 8.67E-01 PASS 2.48E-01 1.30E-03 2.52E-01 2.45E-01 1.00E+00 PASS 2.50E-01 1.79E-03 2.55E-01 2.45E-01 1.00E+00 PASS 2.51E-01 1.30E-03 2.55E-01 2.48E-01 1.00E+00 PASS 0 2.46E-01 2.49E-01 2.48E-01 2.51E-01 2.46E-01 2.50E-01 2.50E-01 2.51E-01 2.46E-01 2.50E-01 2.50E-01 2.46E-01 Total Dose (krad(Si)) 10 20 30 2.48E-01 2.46E-01 2.46E-01 2.47E-01 2.47E-01 2.48E-01 2.46E-01 2.46E-01 2.47E-01 2.49E-01 2.48E-01 2.50E-01 2.46E-01 2.45E-01 2.45E-01 2.45E-01 2.46E-01 2.48E-01 2.45E-01 2.47E-01 2.47E-01 2.47E-01 2.48E-01 2.48E-01 2.43E-01 2.44E-01 2.44E-01 2.46E-01 2.47E-01 2.47E-01 2.50E-01 2.49E-01 2.50E-01 2.46E-01 2.47E-01 2.46E-01 2.48E-01 2.12E-03 2.54E-01 2.42E-01 2.47E-01 1.30E-03 2.51E-01 2.44E-01 2.46E-01 1.14E-03 2.50E-01 2.43E-01 2.49E-01 1.95E-03 2.55E-01 2.44E-01 3.50E-01 PASS 2.45E-01 1.48E-03 2.49E-01 2.41E-01 6.00E-01 PASS 2.46E-01 1.52E-03 2.51E-01 2.42E-01 8.00E-01 PASS An ISO 9001:2008 and DSCC Certified Company 173 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Ps90%/90% (+KTL) Biased Output Voltage Low 4 IL=1mA @ +5V (V) 1.20E+00 1.00E+00 8.00E-01 6.00E-01 4.00E-01 2.00E-01 0.00E+00 0 10 20 30 40 50 Total Dose (krad(Si)) 24hr 60 Anneal 168hr 70 Figure 5.84. Plot of Output Voltage Low 4 IL=1mA @ +5V (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 174 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table 5.84. Raw data for Output Voltage Low 4 IL=1mA @ +5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low 4 IL=1mA @ +5V (V) Device 1101 1104 1105 1106 1107 1108 1109 1110 1111 1113 1124 1125 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 50 2.45E-01 2.40E-01 2.46E-01 2.46E-01 2.41E-01 2.43E-01 2.46E-01 2.44E-01 2.45E-01 2.40E-01 2.41E-01 2.40E-01 24hr Anneal 60 2.48E-01 2.43E-01 2.50E-01 2.49E-01 2.44E-01 2.45E-01 2.48E-01 2.45E-01 2.47E-01 2.42E-01 2.41E-01 2.41E-01 168hr Anneal 70 2.51E-01 2.46E-01 2.51E-01 2.51E-01 2.48E-01 2.45E-01 2.48E-01 2.46E-01 2.48E-01 2.43E-01 2.41E-01 2.41E-01 2.43E-01 3.05E-03 2.51E-01 2.34E-01 2.44E-01 2.88E-03 2.51E-01 2.36E-01 2.47E-01 3.11E-03 2.55E-01 2.38E-01 2.49E-01 2.30E-03 2.56E-01 2.43E-01 2.43E-01 2.17E-03 2.49E-01 2.37E-01 8.67E-01 PASS 2.44E-01 2.30E-03 2.50E-01 2.37E-01 1.00E+00 PASS 2.45E-01 2.30E-03 2.52E-01 2.39E-01 1.00E+00 PASS 2.46E-01 2.12E-03 2.52E-01 2.40E-01 1.00E+00 PASS 0 2.43E-01 2.38E-01 2.46E-01 2.45E-01 2.38E-01 2.44E-01 2.46E-01 2.44E-01 2.46E-01 2.42E-01 2.42E-01 2.41E-01 Total Dose (krad(Si)) 10 20 30 2.43E-01 2.42E-01 2.43E-01 2.40E-01 2.39E-01 2.39E-01 2.46E-01 2.46E-01 2.46E-01 2.44E-01 2.44E-01 2.45E-01 2.41E-01 2.40E-01 2.40E-01 2.40E-01 2.41E-01 2.42E-01 2.43E-01 2.44E-01 2.45E-01 2.41E-01 2.42E-01 2.42E-01 2.43E-01 2.43E-01 2.45E-01 2.38E-01 2.39E-01 2.40E-01 2.42E-01 2.41E-01 2.42E-01 2.41E-01 2.40E-01 2.41E-01 2.42E-01 3.81E-03 2.52E-01 2.32E-01 2.43E-01 2.39E-03 2.49E-01 2.36E-01 2.42E-01 2.86E-03 2.50E-01 2.34E-01 2.44E-01 1.67E-03 2.49E-01 2.40E-01 3.50E-01 PASS 2.41E-01 2.12E-03 2.47E-01 2.35E-01 6.00E-01 PASS 2.42E-01 1.92E-03 2.47E-01 2.37E-01 8.00E-01 PASS An ISO 9001:2008 and DSCC Certified Company 175 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 6.0. Summary / Conclusions The total ionizing dose testing described in this final report was performed using the facilities at Radiation Assured Devices' Longmire Laboratories in Colorado Springs, CO. The high dose rate total ionizing dose (TID) source is a JLSA 81-24 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead, during the radiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from <1rad(Si)/s to a maximum of approximately 120rad(Si)/s, determined by the distance from the source. The parametric data was obtained as "read and record" and all the raw data plus an attributes summary are contained in this report as well as in a separate Excel file. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used in this work is 2.742 per MIL-HDBK-814 using one sided tolerance limits of 90/90 and a 5-piece sample size. The 90/90 KTL values were selected to match the statistical levels specified in the MIL-PRF-38535 sampling plan for the qualification of a radiation hardness assured (RHA) component. Note that the following criteria must be met for a device to pass the total ionizing dose test: following the radiation exposure each of the 5 pieces irradiated under electrical bias shall pass the specification value. The units irradiated without electrical bias and the KTL statistics are included in this report for reference only. If any of the 5 pieces irradiated under electrical bias exceed the datasheet specifications, then the lot could be logged as a failure. Based on this criterion the RH1014MW Quad Precision Operational Amplifier (from the lot date code identified on the first page of this test report) PASSED the total ionizing dose test to the maximum tested dose level of 50krad(Si) with all parameters remaining within their datasheet specifications. Further, the data in this report can be analyzed along with the low dose rate report titled "Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1014MW Quad Precision Operational Amplifier for Linear Technology" to demonstrate that these parts do not exhibit ELDRS as defined in the current test method. An ISO 9001:2008 and DSCC Certified Company 176 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix A: Photograph of a Sample Unit-Under-Test to Show Part Traceability An ISO 9001:2008 and DSCC Certified Company 177 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix B: Radiation Bias Connections TID Radiation Biased Conditions: Extracted from Linear Technology RH1014 Quad Precision Operational Amplifier Datasheet. Pin Function Connection / Bias 1 OUT A To Pin 2 Via 10k Resistor 2 -IN A To Pin 1 Via 10k Resistor 3 +IN A 8V Via 10k Resistor 4 V+ 5 +IN B 8V Via 10k Resistor 6 -IN B To Pin 7 Via 10k Resistor 7 OUT B To Pin 6 Via 10k Resistor 8 OUT C To Pin 9 Via 10k Resistor 9 -IN C To Pin 8 Via 10k Resistor 10 +IN C 8V Via 10k Resistor 11 V- 12 +IN D 8V Via 10k Resistor 13 -IN D To Pin 14 Via 10k Resistor 14 OUT D To Pin 13 Via 10k Resistor +15V Decoupled to GND W/ 0.1F -15V Decoupled to GND W/ 0.1F An ISO 9001:2008 and DSCC Certified Company 178 TID Report 10-492 110223 R1.0 TID Radiation Unbiased Conditions: All pins connected to Ground. Pin Function Connection / Bias 1 OUT A GND 2 -IN A GND 3 +IN A GND 4 V+ GND 5 +IN B GND 6 -IN B GND 7 OUT B GND 8 OUT C GND 9 -IN C GND 10 +IN C GND 11 V- GND 12 +IN D GND 13 -IN D GND 14 OUT D GND An ISO 9001:2008 and DSCC Certified Company 179 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Figure B.1. Irradiation bias circuit for the units to be irradiated under electrical bias. This figure was extracted from Linear Technology RH1014M Quad Precision Operational Amplifier Datasheet. Figure B.2. Package drawing (for reference only). This figure was extracted from Linear Technology RH1014M Quad Precision Operational Amplifier Datasheet. An ISO 9001:2008 and DSCC Certified Company 180 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix C: Electrical Test Parameters and Conditions The expected ranges of values as well as the measurement conditions are taken from Linear Technology RH1014M Quad Precision Operational Amplifier Datasheet. All electrical tests for this device are performed on one of Radiation Assured Device's LTS2020 Test Systems. The LTS2020 Test System is a programmable parametric tester that provides parameter measurements for a variety of digital, analog and mixed signal products including voltage regulators, voltage comparators, D to A and A to D converters. The LTS2020 Test System achieves accuracy and sensitivity through the use of software self-calibration and an internal relay matrix with separate family boards and custom personality adapter boards. The tester uses this relay matrix to connect the required test circuits, select the appropriate voltage / current sources and establish the needed measurement loops for all the tests performed. The measured parameters and test conditions are shown in Table C.1. A listing of the measurement precision/resolution for each parameter is shown in Table C.2. The precision/resolution values were obtained from test data or from the DAC resolution of the LTS-2020 for the particular test shown, whichever is greater. To generate the precision/resolution shown in Table C.2, one of the units-under-test was tested repetitively (a total of 10-times with re-insertion between tests) to obtain the average test value and standard deviation. Using this test data MIL-HDBK-814 90/90 KTL statistics were applied to the measured standard deviation to generate the final measurement range. This value encompasses the precision/resolution of all aspects of the test system, including the LTS2020 mainframe, family board, socket assembly and DUT board as well as insertion error. In some cases, the measurement resolution is limited by the internal DACs, which results in a measured standard deviation of zero. In these instances the precision/resolution will be reported back as the LSB of the DAC. Note that the testing and statistics used in this document are based on an “analysis of variables” technique, which relies on small sample sizes to qualify much larger lot sizes (see MIL-HDBK-814, p. 91 for a discussion of statistical treatments). Not all measured parameters are well suited to this approach due to inherent large variations. If necessary, larger samples sizes could be used to qualify these parameters using an “attributes” approach. An ISO 9001:2008 and DSCC Certified Company 181 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Table C.1. Measured parameters, test conditions, and acceptance criteria for the RH1014MW Quad Precision Operational Amplifier. Parameter Test Conditions Positive Supply Current (ICC+) VS=±15V Negative Supply Current (IEE-) VS=±15V Input Offset Voltage (VOS1-VOS4) VS=±15V Input Offset Current (IOS1-IOS4) VS=±15V + Input Bias Current (IB+1-IB+4) VS=±15V - Input Bias Current (IB-1-IB-4) VS=±15V Common Mode Rejection Ratio (CMRR1-CMRR4) VCM = 13.5V, –15V Power Supply Rejection Ratio (PSRR1-PSRR4) VS = ±10V to ±18V Large Signal Voltage Gain (AVOL9-AVOL12) VS=±15V, VO = ±10V, RL = 10k Positive Output Voltage Swing (VOUT+1-VOUT+4) VS=±15V, RL= 10k Negative Output Voltage Swing (VOUT-1-VOUT-4) VS=±15V, RL= 10k Positive Slew Rate (SlewRate+1 – SlewRate+4) VS=±15V, RL= 10k Negative Slew Rate (SlewRate-1 – SlewRate-4) VS=±15V, RL= 10k Positive Supply Current (ICC+2) VS=+5V Negative Supply Current (IEE-2) VS=+5V Input Offset Voltage (VOS5-VOS8) VS=+5V Input Offset Current (IOS5-IOS8) VS=+5V + Input Bias Current (IB+5-IB+8) VS=+5V - Input Bias Current (IB-5-IB-8) VS=+5V Positive Output Voltage Swing (VOUT+5-VOUT+8) VS=+5V, No Load Positive Output Voltage Swing (VOUT+9-VOUT+12) VS=+5V, RL= 600 Output Voltage Low (VOUT-5-VOUT-8) VS=+5V, No Load Output Voltage Low (VOUT-9-VOUT-12) VS=+5V, RL= 600 Output Voltage Low (VOUT-13-VOUT-16) VS=+5V, ISINK= 1mA An ISO 9001:2008 and DSCC Certified Company 182 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 Table C.2. Measured parameters, pre-irradiation specifications and measurement precision for the RH1014MW Quad Precision Operational Amplifier. Parameter Pre-Irradiation Specification MIN Positive Supply Current (ICC+) MAX Measurement Precision/Resolution 2.20E-03 A ±5.26E-06 A Negative Supply Current (IEE-) -2.20E-03 A ±5.55E-06 A Input Offset Voltage (VOS1-VOS4) -3.00E-04 V 3.00E-04 V ±3.40E-06 V Input Offset Current (IOS1-IOS4) -1.00E-08 A +1.00E-08 A ±3.04E-11 A + Input Bias Current (IB+1-IB+4) -3.00E-08 A 3.00E-08 A ±6.02E-11 A - Input Bias Current (IB-1-IB-4) -3.00E-08 A 3.00E-08 A ±6.48E-11 A Common Mode Rejection Ratio (CMRR1-CMRR4) 97 dB ±4.79E-01 dB Power Supply Rejection Ratio (PSRR1-PSRR4) 100 dB ±3.23E+00 dB 1.20E+03 V/mV ±1.72E+04 V/mV 12.5 V ±1.90E-03 V Large Signal Voltage Gain (AVOL9-AVOL12) Positive Output Voltage Swing (VOUT+1-VOUT+4) Negative Output Voltage Swing (VOUT-1-VOUT-4) -12.5 V Positive Slew Rate (SlewRate+1-SlewRate+4) 0.2 V/µs Negative Slew Rate (SlewRate-1-SlewRate-4) Positive Supply Current (ICC+2) ±8.71E-04 V ±1.26E-02 V/µs -0.2 V/µs ±2.34E-02 V/µs 2.00E-03 A ±3.87E-06 A Negative Supply Current (IEE-2) -2.00E-03 A ±5.08E-06 A Input Offset Voltage (VOS5-VOS8) -4.50E-04 V 4.50E-04 V ±1.00E-06 V Input Offset Current (IOS5-IOS8) -1.00E-08 A 1.00E-08 A ±3.61E-11 A + Input Bias Current (IB+5-IB+8) -5.00E-08 A 5.00E-08 A ±8.80E-11 A - Input Bias Current (IB-5-IB-8) -5.00E-08 A 5.00E-08 A ±7.13E-11 A Positive Output Voltage Swing (VOUT+5-VOUT+8) 4.0 V ±1.17E-03 V Positive Output Voltage Swing (VOUT+9-VOUT+12) 3.4 V ±1.38E-03 V Output Voltage Low (VOUT-5-VOUT-8) 2.50E-02 V ±1.70E-04 V Output Voltage Low (VOUT-9-VOUT-12) 1.00E-02 V ±2.27E-04 V Output Voltage Low (VOUT-13-VOUT-16) 0.35 V ±1.09E-03 V An ISO 9001:2008 and DSCC Certified Company 183 TID Report 10-492 110223 R1.0 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix D: List of Figures Used in the Results Section (Section 5) 5.1. 5.2. 5.3. 5.4. 5.5. 5.6. 5.7. 5.8. 5.9. 5.10. 5.11. 5.12. 5.13. 5.14. 5.15. 5.16. 5.17. 5.18. 5.19. 5.20. 5.21. 5.22. 5.23. 5.24. 5.25. 5.26. 5.27. 5.28. 5.29. 5.30. 5.31. 5.32. 5.33. 5.34. 5.35. 5.36. 5.37. 5.38. Positive Supply Current @ +/-15V (A) Negative Supply Current @ +/-15V (A) Offset Voltage 1 @ +/-15V (V) Offset Voltage 2 @ +/-15V (V) Offset Voltage 3 @ +/-15V (V) Offset Voltage 4 @ +/-15V (V) Offset Current 1 @ +/-15V (A) Offset Current 2 @ +/-15V (A) Offset Current 3 @ +/-15V (A) Offset Current 4 @ +/-15V (A) Positive Bias Current 1 @ +/-15V (A) Positive Bias Current 2 @ +/-15V (A) Positive Bias Current 3 @ +/-15V (A) Positive Bias Current 4 @ +/-15V (A) Negative Bias Current 1 @ +/-15V (A) Negative Bias Current 2 @ +/-15V (A) Negative Bias Current 3 @ +/-15V (A) Negative Bias Current 4 @ +/-15V (A) Common Mode Rejection Ratio 1 (dB) Common Mode Rejection Ratio 2 (dB) Common Mode Rejection Ratio 3 (dB) Common Mode Rejection Ratio 4 (dB) Power Supply Rejection Ratio 1 (dB) Power Supply Rejection Ratio 2 (dB) Power Supply Rejection Ratio 3 (dB) Power Supply Rejection Ratio 4 (dB) Open Loop Gain 1 RL=10k VO=+/-10V (V/mV) Open Loop Gain 2 RL=10k VO=+/-10V (V/mV) Open Loop Gain 3 RL=10k VO=+/-10V (V/mV) Open Loop Gain 4 RL=10k VO=+/-10V (V/mV) Positive Output Voltage 1 @ +/-15V (V) Positive Output Voltage 2 @ +/-15V (V) Positive Output Voltage 3 @ +/-15V (V) Positive Output Voltage 4 @ +/-15V (V) Negative Output Voltage 1 @ +/-15V (V) Negative Output Voltage 2 @ +/-15V (V) Negative Output Voltage 3 @ +/-15V (V) Negative Output Voltage 4 @ +/-15V (V) An ISO 9001:2008 and DSCC Certified Company 184 TID Report 10-492 110223 R1.0 5.39. 5.40. 5.41. 5.42. 5.43. 5.44. 5.45. 5.46. 5.47. 5.48. 5.49. 5.50. 5.51. 5.52. 5.53. 5.54. 5.55. 5.56. 5.57. 5.58. 5.59. 5.60. 5.61. 5.62. 5.63. 5.64. 5.65. 5.66. 5.67. 5.68. 5.69. 5.70. 5.71. 5.72. 5.73. 5.74. 5.75. 5.76. 5.77. 5.78. 5.79. 5.80. Positive Slew Rate 1 @ +/-15V (V/us) Positive Slew Rate 2 @ +/-15V (V/us) Positive Slew Rate 3 @ +/-15V (V/us) Positive Slew Rate 4 @ +/-15V (V/us) Negative Slew Rate 1 @ +/-15V (V/us) Negative Slew Rate 2 @ +/-15V (V/us) Negative Slew Rate 3 @ +/-15V (V/us) Negative Slew Rate 4 @ +/-15V (V/us) Positive Supply Current @ +5V (A) Negative Supply Current @ +5V (A) Offset Voltage 1 @ +5V (V) Offset Voltage 2 @ +5V (V) Offset Voltage 3 @ +5V (V) Offset Voltage 4 @ +5V (V) Offset Current 1 @ +5V (A) Offset Current 2 @ +5V (A) Offset Current 3 @ +5V (A) Offset Current 4 @ +5V (A) Positive Bias Current 1 @ +5V (A) Positive Bias Current 2 @ +5V (A) Positive Bias Current 3 @ +5V (A) Positive Bias Current 4 @ +5V (A) Negative Bias Current 1 @ +5V (A) Negative Bias Current 2 @ +5V (A) Negative Bias Current 3 @ +5V (A) Negative Bias Current 4 @ +5V (A) Positive Output Voltage 1 RL=open @ +5V (V) Positive Output Voltage 2 RL=open @ +5V (V) Positive Output Voltage 3 RL=open @ +5V (V) Positive Output Voltage 4 RL=open @ +5V (V) Positive Output Voltage 1 RL=600 @ +5V (V) Positive Output Voltage 2 RL=600 @ +5V (V) Positive Output Voltage 3 RL=600 @ +5V (V) Positive Output Voltage 4 RL=600 @ +5V (V) Output Voltage Low 1 RL=open @ +5V (V) Output Voltage Low 2 RL=open @ +5V (V) Output Voltage Low 3 RL=open @ +5V (V) Output Voltage Low 4 RL=open @ +5V (V) Output Voltage Low 1 RL=600 @ +5V (V) Output Voltage Low 2 RL=600 @ +5V (V) Output Voltage Low 3 RL=600 @ +5V (V) Output Voltage Low 4 RL=600 @ +5V (V) An ISO 9001:2008 and DSCC Certified Company 185 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 TID Report 10-492 110223 R1.0 5.81. 5.82. 5.83. 5.84. Output Voltage Low 1 IL=1mA @ +5V (V) Output Voltage Low 2 IL=1mA @ +5V (V) Output Voltage Low 3 IL=1mA @ +5V (V) Output Voltage Low 4 IL=1mA @ +5V (V) An ISO 9001:2008 and DSCC Certified Company 186 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800