RCL e3 Vishay Long Side Termination Thick Film Chip Resistors FEATURES • Enhanced power rating • Long side terminations • Protective overglaze • Pure tin solder contacts on Ni barrier layer, provides compatibility with lead (Pb)-free and lead containing soldering processes • Compliant to RoHS directive 2002/95/EC • Halogen-free according to IEC 61249-2-21 definition • AEC-Q200, rev. C compliant STANDARD ELECTRICAL SPECIFICATIONS SIZE MODEL INCH METRIC RCL0612 e3 RCL1218 e3 0612 1218 POWER RATING P70 W LIMITING ELEMENT VOLTAGE MAX. V 0.5 75 RR1632 RR3246 1.0 TEMPERATURE COEFFICIENT ppm/K TOLERANCE % ± 100 ±1 RESISTANCE RANGE E-SERIES Ω E24 + E96 1 to 1M ± 200 ±5 ± 100 ±1 200 E24 E24 + E96 1 to 2M2 ± 200 ±5 E24 Notes • These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime • Marking: See data sheet “Surface Mount Resistor Marking” (document number 20020) • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material TECHNICAL SPECIFICATIONS PARAMETER UNIT RCL0612 RCL1218 Rated Dissipation P70 (1) W 0.5 1.0 Limiting Element Voltage Umax. AC/DC V 75 200 Insulation Voltage Uins. (1 min) V > 100 > 200 Insulation Resistance Ω > 109 Category Temperature Range °C - 55 to + 155 Weight mg 11 29.5 Note (1) The power dissipation on the resistors generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. www.vishay.com 1 For technical questions, contact: [email protected] Document Number: 20046 Revision: 04-Mar-10 RCL e3 Long Side Termination Thick Film Chip Resistors Vishay PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: RCL061210K0FKEA(1) R C L 0 MODEL/SIZE RCL0612 RCL1218 6 1 2 1 VALUE R = Decimal K = Thousand M = Million 0000 = Jumper 0 K 0 F K E A TOLERANCE F=±1% J=±5% Z = Jumper TCR K = ± 100 ppm/K N = ± 200 ppm/K 0 = Jumper PACKAGING (2) EA EB EC EK SPECIAL Up to 2 digits PRODUCT DESCRIPTION: RCL0612 10K 1 % 100 ET1 e3 RCL0612 10K 1% 100 ET1 e3 MODEL RCL0612 RCL1218 RESISTANCE VALUE TOLERANCE TCR PACKAGING (2) LEAD (Pb)-FREE 10R = 10 Ω 10K = 10 kΩ 1M = 1 MΩ 0R0 = Jumper ±1% ±5% ± 100 ppm/K ± 200 ppm/K ET1 ET5 ET6 ET9 e3 = Pure tin termination finish Notes (1) Preferred way for ordering products is by use of the PART NUMBER (2) Please refer to table PACKAGING, see below PACKAGING REEL PACKAGING CODE MODEL TAPE WIDTH DIAMETER PIECES/ REEL PITCH PART NUMBER PAPER RCL0612 8 mm RCL1218 12 mm PRODUCT DESC. BLISTER PAPER 180 mm/7" 4 mm 5000 EA 285 mm/11.25" 4 mm 10 000 EB ET5 330 mm/13" 4 mm 20 000 EC ET6 180 mm/7" 4 mm 4000 BLISTER ET1 EK ET9 DIMENSIONS in millimeters T2 L a H l b W T1 SIZE SOLDER PAD DIMENSIONS DIMENSIONS REFLOW SOLDERING WAVE SOLDERING INCH METRIC L W H T1 T2 a b l a b l 0612 1632 1.6 ± 0.2 3.2 ± 0.2 0.55 ± 0.1 0.35 ± 0.15 0.25 ± 0.15 0.6 3.2 1.0 1.1 3.2 1.0 1218 3246 4.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 1.1 4.9 1.9 1.25 4.8 1.9 3.2 Document Number: 20046 Revision: 04-Mar-10 + 0.10 - 0.20 For technical questions, contact: [email protected] www.vishay.com 2 RCL e3 Long Side Termination Thick Film Chip Resistors Vishay FUNCTIONAL PERFORMANCE Rated Power in % Derating 120 100 80 60 40 20 0 - 55 - 25 0 25 50 75 70 100 125 155 175 Ambient Temperature in °C TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (ΔR) STABILITY CLASS 2 OR BETTER Stability for product types: 1 Ω to 1 MΩ RCL e3 4.5 - Resistance - 4.7 - Voltage proof U = 1.4 x Uins; 60 s 4.13 - Short time overload U = 2.5 x P 70 x R ≤ 2 x Umax.; Duration acc. to style 4.17.2 58 (Td) ±1% ±5% No flashover or breakdown ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) Solder bath method; Sn60Pb40 non activated flux; (235 ± 5) °C (2 ± 0.2) s Good tinning (≥ 95 % covered); no visible damage Solder bath method; Sn96.5Ag3Cu0.5 non-activated flux; (245 ± 5) °C (3 ± 0.3) s Good tinning (≥ 95 % covered); no visible damage Solderability - Temperature coefficient (20/- 55/20) °C and (20/125/20) °C 4.32 21 (Uu3) Shear (adhesion) 45N No visible damage 21 (Uu1) Substrate bending Depth 2 mm; 3 times No visible damage, no open circuit in bent position 4.33 4.8.4.2 4.19 14 (Na) www.vishay.com 3 Rapid change of temperature ± 100 ppm/K ± 200 ppm/K ± (0.25 % R + 0.05 Ω) 30 min at - 55 °C; 30 min at 125 °C 5 cycles ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) 1000 cycles ± (1 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) For technical questions, contact: [email protected] Document Number: 20046 Revision: 04-Mar-10 RCL e3 Long Side Termination Thick Film Chip Resistors Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (ΔR) STABILITY CLASS 2 OR BETTER Stability for product types: 1 Ω to 1 MΩ RCL e3 4.23 4.23.2 2 (Ba) Climatic sequence: Dry heat 4.23.3 30 (Db) Damp heat, cyclic 4.23.4 4.23.5 1 (Aa) 13 (M) Cold Low air pressure 4.23.6 30 (Db) Damp heat, cyclic 4.23.7 - DC load 4.25.1 - Endurance at 70 °C 4.18.2 58 (Td) Resistance to soldering heat 4.35 - Flamability, needle flame test 4.24 78 (Cab) Damp heat, steady state 4.25.3 - Endurance at upper category temperature 4.40 - Electrostatic discharge (Human Body Model) 4.29 45 (XA) Component solvent resistance 4.30 45 (XA) Solvent resistance of marking 4.22 6 (Fc) Vibration, endurance by sweeping 4.37 - Periodic electric overload 4.27 - Single pulse high voltage overload, 10 µs/700 µs 125 °C; 16 h 55 °C; ≥ 90 % RH; 24 h; 1 cycle - 55 °C; 2 h 1 kPa; (25 ± 10) °C; 1 h 55 °C; ≥ 90 % RH; 24 h; 5 cycles U = P 70 x R U = P 70 x R ≤ Umax.; 1.5 h on; 0.5 h off; 70 °C; 1000 h 70 °C; 8000 h Solder bath method (260 ± 5) °C; (10 ± 1) s IEC 60695-11-5; 10 s (40 ± 2) °C; (93 ± 3) % RH; 56 days 155 °C, 1000 h IEC 61340-3-1* 3 pos. + 3 neg. discharges; ESD voltage: 1000 V Isopropyl alcohol; 50 °C; method 2 Isopropyl alcohol; 50 °C; method 1, toothbrush f = 10 Hz to 2000 Hz; x, y, z ≤ 1.5 mm; A ≤ 200 m/s2; 10 sweeps per axis U = 15 x P 70 x R ≤ 2 x Umax.; 0.1 s on; 2.5 s off; 1000 cycles Û = 10 x P 70 x R ≤ 2 x Umax.; 10 pulses ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) ± (0.5 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) ± (4 % R + 0.1 Ω) ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) No burning after 30 s ± (1 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) ± (1 % R + 0.05 Ω) No visible damage Marking legible, no visible damage ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) All tests are carried out in accordance with the following specifications: • EN 60115-1, generic specification • EN 140400, sectional specification • EN 140401-802, detail specification • IEC 60068-2 environmental test procedures Packaging of components is done in paper or blister tapes according to IEC 60286-3 Document Number: 20046 Revision: 04-Mar-10 For technical questions, contact: [email protected] www.vishay.com 4 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1