DEMO MANUAL DC1979A LTC6090 High Voltage CMOS Amplifier Description Demonstration circuit 1979A is a high voltage CMOS amplifier featuring the LTC®6090. An onboard isolated flyback converter provides ±62V power to the LTC6090 for evaluating large signal performance. A jumper sets the gain of the ultrahigh-input impedance circuit to either unity (1×) or 20×. In the 20× mode, a signal input of just 3V can provide nearly full-swing output. In the unity-gain setting, the part operates as a precision buffer for high voltage signals. SPECIAL FORM-FACTOR The DC1979A includes a preassembled power converter and amplifier circuit on a small printed circuit, so the user only needs to furnish a 7V to 12V power source to operate the demo. The layout has provisions for optional BNC connectors and mounting features to install the board in a standard plastic enclosure if a permanent utility unit is desired. Refer to the Appendix for mechanical details. Design files for this circuit board are available at http://www.linear.com/demo L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Performance Summary Specifications are at TA = 25°C SYMBOL PARAMETER CONDITIONS VIN Input Signal, Maximum Usable Gain = 20×, Onset of Output Clipping Gain = 1×, VCM Limited IIN VIN Leakage Current VIN = Within Usable Range VOUT Output Voltage Range Gain = 20×, Onset of Output Clipping VSUPPLY Input to Supply Converter ISUPPLY Quiescent Supply Current UVLO Undervoltage Lockout MIN 7 VIN = 9V, No Loading of Op Amp Output TYP MAX UNITS ±3.1 ±60 V V 3 pA ±62 V 9 12 V 62 mA 6.5 V Operating Principles The LTC6090 op amp is set up in the standard noninverting voltage-gain configuration. GAIN jumper JP2 provides a means of controlling the gain by adding or deleting a gain resistor in the feedback path by choosing the 1× or 20× setting. A small LT®8300 flyback converter is used to provide about ±65V from a convenient low voltage supply in the 7V to 12V range. A blue LED is in series with the minus supply to the LTC6090, so the op amp actually sees a resultant supply of about 65V/–62V. The LED provides a pleasant level of illumination at the 2.6mA quiescent current of the op amp. To minimize signal loading, no input load resistor is included. The op amp can be connected to the instrumentation with a coaxial cable at J2, since a 50Ω output termination is included. No far-end termination should be used, as the op amp cannot deliver large signals across a 100Ω DC load. In the event of an output overload, the LTC6090, having built-in thermal shutdown, will automatically go into a low power state to protect itself from damage. After dc1979af 1 DEMO MANUAL DC1979A Operating Principles cooling down some, the part will automatically resume (or attempt) normal operation, usually in a fraction of a second. This safety feature can be defeated if desired by setting the THERMAL S/D jumper JP1 to the 0 setting. To evaluate the LTC6090 at other power supply voltages, or without any noise contribution from the onboard flyback circuit, supply potentials can be furnished directly to the op amp without powering the LT8300. Solder tacking wires to the C4 and C6 bypass capacitors is the most convenient means of supplying external power. A ground turret is provided for any alternate powering or instrument grounding needs. Refer to the Schematic Diagram in this document for the circuit details. Quick Start Procedure Demonstration circuit 1979A is easy to set up to evaluate the performance of the LTC6090. Refer to Figure 1 for proper measurement equipment setup and follow the procedure below (CAUTION: HIGH VOLTAGES!): 1. Place jumpers in the following positions: JP1: Position 1 (enables THERMAL S/D) JP2: Position 20× (for GAIN of 20) 2. With power off, connect the input power supply to +V and –V. A good setting is 9V, or a 9V battery can be used. NOTE: The flyback converter input is isolated from the op amp GND, so when used for the op amp supply, the DC input will not use the GND connection. 3. Connect a signal generator at the IN+ and GND turrets. 10kHz sine wave at 1V is a good starting point. NOTE: If the supply and instruments share a chassis ground connection, the isolation of the flyback converter is lost. 4. Connect an oscilloscope 10× probe to the OUT and GND turrets. Set the scaling to 20V/20µs per division. 5. Power up the system and a 20V sine wave should appear on the oscilloscope. 6. Increase the signal amplitude and observe the signal for clipping as signals reach the supply rails. Slew and settling behavior can be evaluated by switching the signal generator to square wave. Figure 1. Proper Measurement Equipment Setup 2 dc1979af DEMO MANUAL DC1979A Appendix One especially useful purpose for the DC1979A is to provide precision measurements in higher voltage circuits. The usual 10MΩ presented by most instruments will often unacceptably load such circuits and give highly erroneous results. For providing a wide-range signal buffer, the GAIN jumper is set to 1× so that the only errors are from the VOS and input leakage current of the LTC6090. With a ±50V reading on a 4½ digit DMM (i.e., 200V scale), this error is generally less than one count of the display (10mV), even for a several-GΩ source resistance signal. If one desires to use the DC1979A as a permanent high voltage buffer unit, then the following information will be helpful. THE CONSTRUCTION The following sketches show the hole placement for the BNC connectors and an optional toggle switch. The toggle switch is for use with a 9V battery that can fit inside the case, or other provisions could be made to provide power connections to the board as desired (for example, a banana jack, wall-wart DC jack, etc.). Figure 2 provides the hole placement for the OUT signal (on J2). This is to pass the output signal through the bottom of the case using a back-mounted Connex 112404 vertical BNC connector. Two 4-40-1/4" screws are needed to mount the PCB to the case. Figure 3 shows the hole placement for the end panel. It includes the IN signal on J1 using a Molex SD-73100-0105 right-angle BNC connector on the top side of the board, and the smaller hole is for the miniature toggle switch, such as from the manufacturer, C&K. Figure 2. Base Hole and PCB Location Figure 3. End Panel Hole Locations dc1979af 3 DEMO MANUAL DC1979A Appendix Figure 4 is an interior photo of the finished unit including the switch and 9V battery. The translucent blue Hammond 1593KTBU was selected so the LED would be visible during operation. Standard adapters can be used to transform the output into a banana-plug pair that can directly attach the unit to a DMM, as shown in Figure 5. Figure 4. Interior of Completed Unit Figure 5. Completed Unit Attached to DMM Parts List ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER CAP., 1206, 1µF, 10%, 100V, X7R MURATA, GRM31CR72A105KA01L Required Circuit Components 1 2 C1, C3 2 1 C2 CAP., 1206, 4.7µF, 10%, 25V, X7R MURATA, GRM31CR71E475KA88L 3 2 C4, C6 CAP., X7R, 0.1µF, 100V, 10%, 0805 MURATA, GCM21BR72A104KA37L 4 0 C5 CAP., COG, 15pF, 100V, 5%, TH, OPT 5 1 C7 CAP., NPO, 5.6pF, 100V, ±0.25pF, 0603 AVX, 06031A5R6CAT2A 6 2 D1, D3 SWITCHING DIODE, SOD-123 CENTRAL SEMICONDUCTOR, CMMR1U-02 7 1 D2 SM ZENER DIODE, SOD-123, CMHZ5266B CENTRAL SEMICONDUCTOR, CMHZ5266B 8 5 E1-E5 TURRET MILL-MAX, 2308-2-00-80-00-00-07-0 9 2 JP1, JP2 HEADER, 3-PIN, 2mm SAMTEC, TMM-103-02-L-S 10 2 XJP1, XJP2 SHUNT SAMTEC, 2SN-BK-G 11 0 J1 CON, BNC-J/RA/PCB (OPT) MOLEX INC., SD-73100-0105 12 0 J2 CON, BNC, 5 PINS (OPT) CONNEX, 112404 13 1 LED1 LED, 1206, BLUE PANASONIC, LNJ951C4BRA 14 1 L1 IND., 1206 MURATA, BLM31PG330SN1L 15 1 R1 RES., CHIP, 100k, 1/10W, 1%, 0603 VISHAY, CRCW0603100KFKEA 16 1 R2 RES., CHIP, 23.2k, 1/10W, 1%, 0603 VISHAY, CRCW060323K2FKEA 17 1 R3 RES., CHIP, 130k, 1/10W, 1%, 0603 VISHAY, CRCW0603130KFKEA 18 2 R4, R7 RES., CHIP, 100Ω, 1/10W, 1%, 0603 VISHAY, CRCW0603100RFKEA 19 2 R5, R9 RES., CHIP, 5.23k, 1/10W, 1%, 0603 VISHAY, CRCW06035K23FKEA 20 1 R6 RES., CHIP, 49.9Ω, 1/10W, 1%, 0603 VISHAY, CRCW060349R9FKEA dc1979af 4 DEMO MANUAL DC1979A Parts List ITEM QTY 21 1 REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER R8 RES., CHIP, 100k, 1/16W, 1%, 1206 VISHAY, CRCW1206100KFKEA 22 1 T1 TRANSFORMER WÜRTH ELEKTRONIK, 750311692 23 1 U1 I.C., S8E PACKAGE LINEAR TECHNOLOGY, LTC6090CS8E 24 1 U2 I.C., 5-LEAD TSOT PACKAGE LINEAR TECHNOLOGY, LT8300ES5#PBF-ES Schematic Diagram Figure 6. DC1979A High Voltage CMOS Amplifier dc1979af Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 5 DEMO MANUAL DC1979A DEMONSTRATION BOARD IMPORTANT NOTICE Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations. If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind. LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive. Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and observe good laboratory practice standards. Common sense is encouraged. This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer. Mailing Address: Linear Technology 1630 McCarthy Blvd. Milpitas, CA 95035 Copyright © 2004, Linear Technology Corporation dc1979af 6 Linear Technology Corporation LT 0113 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2013