TC120 PWM/PFM Step-Down Combination Regulator/Controller Package Type Features • Internal Switching Transistor Supports 600mA Output Current • External Switching Transistor Control for Output Currents of 2A+ • 300kHz Oscillator Frequency Supports Small Inductor Size • Short Circuit Protection • Built-In Undervoltage Lockout • 95% Typical Efficiency • Automatic Switchover to Current-Saving PFM Mode at Low Output Loads • Automatic Output Capacitor Discharge While in Shutdown • Programmable Soft-Start • Power-Saving Shutdown Mode • Small 8-Pin SOP Package 8-Pin SOP TC120503EHA 5.0 8-Pin SOP -40°C to +85°C TC120333EHA 3.3 8-Pin SOP -40°C to +85°C TC120303EHA 3.0 8-Pin SOP -40°C to +85°C CPC 3 6 GND SHDN/SS 4 5 SENSE The TC120 consumes only 55A (max) of supply current (VOUT = 3.3V) and can be placed in shutdown mode by bringing the shutdown input (SHDN) low. During shutdown, the regulator is disabled, supply current is reduced to 2.5A (max), and VOUT is internally pulled to ground, discharging the output capacitor. Normal operation resumes when SHDN is brought high. Other features include a built-in undervoltage lockout (UVLO), an externally programmable soft start time, and output short circuit protection. The TC120 operates from a maximum input voltage of 10V and is available in a low-profile 8-Pin SOP package. Operating Temp. Range Package EXT TC120 is a 300kHz PFM/PWM step-down (Buck) DC/ DC regulator/controller combination for use in systems operating from two or more cells, or in line-powered applications. It uses PWM as the primary modulation scheme, but automatically converts to PFM at low output loads for greater efficiency. It requires only an external inductor, Schottky diode, and two capacitors to implement a step-down converter having a maximum output current of 600mA (VIN = 5V, VOUT = 3.3V). An external switching transistor (P-channel MOSFET) can be added to increase output current capability to support output loads of 2A or more. Device Selection Table Output Voltage (V) 7 TC120 General Description Portable Test Equipment Local Logic Supplies Portable Audio Systems Portable Scanners Palmtops Electronic Organizers Part Number LX EXTW 2 Applications • • • • • • 8 VIN 1 Functional Block Diagram L1 VIN VOUT LX VIN D1 CIN EXTW COUT EXT TC120XX03 CPC SHDN/SS GND SENSE CSS 4.7nF 2001-2012 Microchip Technology Inc. DS21365C-page 1 TC120 1.0 ELECTRICAL CHARACTERISTICS *Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings* Power Supply Voltage (VIN).................... -0.3V to +12V Voltage on VOUT Pin ............................... -0.3V to +12V Voltage on LX, Boost Pins ................................... (VIN – 12V) to (VIN + 0.3V) Voltage on EXT1, EXT2, SHDN Pins .......................................... (-0.3V) to (VIN + 0.3V) LX Pin Current .............................................. 700mA pk EXT1, EXT2 Pin Current ...................................±50mA Continuous Power Dissipation .........................300mW Operating Temperature Range.............-40°C to +85°C Storage Temperature Range ..............-40°C to +150°C TC120 ELECTRICAL SPECIFICATIONS Electrical Characteristics: Test circuit of Figure 3-1, TA = 25C, VIN = VR x 1.2, Note 1 unless otherwise noted. Symbol Parameter VOUT Output Voltage VIN Input Voltage Min Typ Max VR x 0.975 VR ± 0.5% VR x 1.025 Units V Test Conditions VOUT = 3.0V IOUT = 120mA (Note 1) VOUT = 3.3V IOUT = 132mA VOUT = 5.0V IOUT = 200mA 1.8 — 10.0 V IOUTMAX Maximum Output Current 500 600 600 — — — — — — mA VOUT = 3.0V VOUT = 3.3V VOUT = 5.0V IIN Supply Current — 52 55 71 82 86 110 A VOUT = 3.0V VIN = VR x 1.05, no load VOUT = 3.3V VOUT = 5.0V ISHDN Shutdown Supply Current — 1.5 2.5 A No load, SHDN = 0V, (Note 2) ILX LX Pin Leakage Current — — — 1.5 2 2.5 A Measured at EXT1 Pin (Note 2) No load, SHDN = 0V RDSON(L LX Pin ON Resistance X) — — — 0.69 0.64 0.44 0.94 0.85 0.58 VOUT = 3.0V VOUT = VR x 0.9 (Note 2) VOUT = 3.3V VLX = VIN – 0.2V, 10 VOUT = 5.0V Resistor from LX to VIN, SHDN = VIN REXTH EXT1, EXT2 On Resistance to VIN — — — 38 35 24 52 47 32 VOUT = 3.0V SHDN = VIH; EXT1 and EXT2 VOUT = 3.3V connected to 200 load, VOUT = 5.0V VEXT1 = VEXT2 = (VIN – 0.4V); VOUT = VIN (Note 2) REXTL EXT1, EXT2 On Resistance to GND — — — 31 29 20 41 37 26 VOUT = 3.0V SHDN = VIH; EXT1 and EXT2 VOUT = 3.3V pulled up through a series VOUT = 5.0V resistance of 200to a voltage such that VEXT1, 2 = 0.4V fOSC Oscillator Frequency 255 300 345 kHz DPWM Maximum PWM Duty Cycle — — 100 % DPFM PFM Duty Cycle 15 25 35 % No load Efficiency — 95 — % VIN > VR x 1.2 Note 1: 2: 3: Measured at EXT1 Pin, VIN = VOUT + 0.3V, IOUT = 20mA (Note 3) VR is the factory-programmed output voltage setting. No external components connected, except CSS. While operating in PWM Mode. DS21365C-page 2 2001-2012 Microchip Technology Inc. TC120 Electrical Characteristics: Test circuit of Figure 3-1, TA = 25C, VIN = VR x 1.2, Note 1 unless otherwise noted. Parameter Min Typ Max Units VUVLO Symbol Minimum Operating Voltage 0.9 — 1.8 V VOUT = VR x 0.9 (Note 2), SHDN = VIN Measured with internal transistor in OFF state and VIN falling VIH SHDN Input Logic High, Threshold Voltage 0.65 — — V VOUT = 0V, (Note 2) VIL SHDN Input Logic Low, Threshold Voltage — — 0.20 V VOUT = 0V, (Note 2) tPRO Short Circuit Protection Response Time 3 5 8 msec Soft Start Time 6 10 16 msec tSS Note 1: 2: 3: Test Conditions Time from VOUT = 0V to SHDN = VIL (Note 2) VR is the factory-programmed output voltage setting. No external components connected, except CSS. While operating in PWM Mode. 2001-2012 Microchip Technology Inc. DS21365C-page 3 TC120 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE Pin No. (8-Pin SOP) Symbol 1 VIN 2 EXTW Extended external switching transistor drive output. This output follows the timing on the EXT output with an additional 100nsec blanking time on both the leading and trailing edges. That is, this output transitions from high-to-low 100 nsec prior to the same transition on EXT; and transitions low-to-high 100nsec after the same transition on EXT; resulting in a longer external switch ON time. (See Section 3.9 External Switching Transistor Selection). 3 CPC Charge pump capacitor input. An inverting charge pump is formed by attaching a capacitor and diode to this input. (See Section 3.5 Improving High Load Efficiency In Regulator Operating Mode). 4 SHDN/SS Shutdown and soft-start control input. A soft start capacitor of 100pF (min) must be connected to this input. The soft start capacitor is charged by an internal A current source that gently ramps the TC120 into service. Shutdown control is best implemented with an external open collector (or open drain) switch. The TC120 enters shutdown when this input is low. During shutdown, the regulator is disabled, and supply current is reduced to less than 2.5A. Normal operation is restored when this input is open-circuited, and allowed to float high. (See Section 3.6 Low Power Shutdown Mode/Soft Start Input). 5 SENSE 6 GND Ground terminal. 7 EXT External switching transistor drive output. This output connects directly to the gate of an external P-channel MOSFET for applications requiring output currents greater than 600mA. The timing of this output exactly matches that of the gate drive for the internal P-channel transistor. This output can drive a maximum capacitance of 1000pF. (See Section 3.9 External Switching Transistor Selection). 8 Lx Inductor terminal. This pin is connected to the drain of the internal P-channel switching transistor. If the TC120 is operated as a regulator (i.e., using the internal switch); the inductor must be connected between this pin and the SENSE pin. DS21365C-page 4 Description Unregulated supply input. Voltage sense input. This input must be connected to the output voltage node at the physical location that requires the tightest voltage regulation. 2001-2012 Microchip Technology Inc. TC120 3.0 DETAILED DESCRIPTION 3.2 The TC120 can be operated as an integrated stepdown regulator (using the internal switching transistor); or as a step-down regulator controller (using an external switching transistor). When operating as an integrated regulator, the only required external components are a Schottky diode, inductor and an output capacitor. Operating in this configuration, the TC120 is capable of supporting output load currents to a maximum of 600mA with operating efficiencies above 85%. Efficiencies at high loads can be further improved by using the on-board charge pump circuit to pull the gate of the internal switching transistor below ground for the lowest possible ON resistance. (For more information, see Section 3.5 Improving High Load Efficiency in Regulator Operating Mode). Higher output currents are achieved by operating the TC120 with an external P-channel switching transistor (controller mode). In this operating configuration, the maximum output current is determined primarily by the ON resistance of the P-channel switch and the series resistance of the inductor. FIGURE 3-1: TEST CIRCUIT L1 22μH VIN – 47μF/10V Tantalum VOUT LX VIN + + IN5817 EXTW EXT TC120XX03 CPC SHDN/SS – COUT 47μF/10V Tantalum GND SENSE CSS 4.7nF 3.1 Inductor Selection Selecting the proper inductor value is a trade-off between physical size and power conversion requirements. Lower value inductors cost less, but result in higher ripple current and core losses. They are also more prone to saturate since the coil current ramps faster and could overshoot the desired peak value. This not only reduces efficiency, but could also cause the current rating of the external components to be exceeded. Larger inductor values reduce both ripple current and core losses, but are larger in physical size and tend to increase the start-up time slightly. A 22H inductor is the best overall compromise and is recommended for use with the TC120. For highest efficiency, use inductors with a low DC resistance (less than 20m). To minimize radiated noise, consider using a toroid, pot core or shielded-bobbin inductor. 2001-2012 Microchip Technology Inc. Input Bypass Capacitor Using an input bypass capacitor reduces peak current transients drawn from the input supply, and reduces the switching noise generated by the regulator. The source impedance of the input supply determines the size of the capacitor that should be used. 3.3 Output Capacitor The effective series resistance of the output capacitor directly affects the amplitude of the output voltage ripple. (The product of the peak inductor current and the ESR determines output ripple amplitude.) Therefore, a capacitor with the lowest possible ESR should be selected. Smaller capacitors are acceptable for light loads or in applications where ripple is not a concern. A 47F Tantalum capacitor is recommended for most applications. The Sprague 595D series of tantalum capacitors are amongst the smallest of all low ESR surface mount capacitors available. Table 3-1 lists suggested components and suppliers. 3.4 Catch Diode The high operating frequency of the TC120 requires a high-speed diode. Schottky diodes such as the MA737 or 1N5817 through 1N5823 (and the equivalent surface mount versions) are recommended. Select a diode whose average current rating is greater than the peak inductor current; and whose voltage rating is higher than VINMAX. 3.5 Improving High Load Efficiency in Regulator Operating Mode If the TC120 is operated at high output loads most (or all) of the time, efficiency can be improved with the addition of two components. Ordinarily, the voltage swing on the gate of the internal P-channel transistor is from ground to VIN. By adding a capacitor and diode as shown in Figure 3-2, an inverting charge pump is formed, enabling the internal gate voltage to swing from a negative voltage to +VIN. This increased drive lowers the RDSON of the internal transistor, improving efficiency at high output currents. Care must be taken to ensure the voltage measured between VIN and CPC does not exceed an absolute value of 10V. While this is not a problem at values of VIN at (or below) 5V, higher VIN values will require the addition of a clamping mechanism (such as a Zener diode) to limit the voltage as described. While this technique improves efficiency at high output loads, it is at the expense of low load efficiency because energy is expended charging and discharging the charge pump capacitor. This technique is therefore not recommended for applications that operate the TC120 at low output currents for extended time periods. If unused, CPC must be grounded. DS21365C-page 5 TC120 3.6 Low Power Shutdown Mode/Soft Start Input The SHDN/SS input acts as both the shutdown control and the node for the external soft start capacitor, which is charged by an internal 1A current source. A value of 4700pF (100pF minimum) is recommended for the soft start capacitor. Failure to do this may cause large overshoot voltages and/or large inrush currents resulting in possible instability. The TC120 enters a low power shutdown mode when SHDN/SS is brought low. While in shutdown, the oscillator is disabled and the output discharge switch is turned on, discharging the output capacitor. Figure 3-3 shows the recommended interface circuits to the SHDN/SS input. As shown, the SHDN/SS input should be controlled using an open collector (or open drain) device, such that the SHDN/ SS input is grounded for shutdown mode, and opencircuited for normal operation (Figure 3-3a). If a CMOS device is used to control shutdown (Figure 3-3b), the value of R1 and CSS should be chosen such that the voltage on SHDN/SS rises from ground to 0.65V in 1.5msec (Figure 3-4). If shutdown is not used, CSS must still be connected as shown in Figure 3-3c and Figure 3-3d. SHDN/SS may be pulled up with a resistor (Figure 3-3c) as long as the values of RSS and CSS provide the approximate charging characteristic on power up shown in Figure 3-4. CSS only may also be connected as shown in Figure 3-3d with CSS chosen at 4700pF (minimum 100pF). 3.7 Undervoltage Lockout (UVLO) The TC120 is disabled whenever VIN is below the undervoltage lockout threshold. This threshold is equal to the guaranteed minimum operating voltage for the TC120 (i.e., 2.2V). When UVLO is active, the TC120 is completely disabled. 3.8 3.9 External Switching Transistor Selection EXT is a complimentary output with a maximum ON resistances of 32 to VDD when high and 26 to ground when low, at VOUT = 5V. It is designed to directly drive a P-channel MOSFET (Figure 3-5). The P-channel MOSFET selection is determined mainly by the on-resistance, gate-source threshold and gate charge requirements. Also, the drain-to-source and gate-to-source breakdown voltage ratings must be greater than VINMAX. The total gate charge specification should be less than 100nC for best efficiency. The MOSFET must be capable of handling the required peak inductor current, and should have a very low onresistance at that current. For example, a Si9430 MOSFET has a drain-to-source rating of -20V, and a typical on-resistance rDSON of 0.07 at 2A, with VGS = -4.5V. (EXTW (Figure 3-6) may be gated with external circuitry to add blanking, or as an auxiliary timing signal.) Table 3-1 lists suggested components and suppliers. 3.10 Board Layout Guidelines As with all inductive switching regulators, the TC120 generates fast switching waveforms, which radiate noise. Interconnecting lead lengths should be minimized to keep stray capacitance, trace resistance and radiated noise as low as possible. In addition, the GND pin, input bypass capacitor and output filter capacitor ground leads should be connected to a single point. The input capacitor should be placed as close to power and ground pins of the TC120 as possible. The length of the EXT trace must also be kept as short as possible. Short Circuit Protection Upon detection of an output short circuit condition, the TC120 reduces the PWM duty cycle to a minimum value using its internal protection timer. The sequence of events is as follows: when an output voltage decrease to near zero is detected (as the result of an overload), the internal (5msec) protection timer is started. If the output voltage has not recovered to nominal value prior to the expiration of the protection timer, the TC120 is momentarily shut down by dedicated, internal circuitry. Immediately following this action, the soft start sequence is engaged in an attempt to re-start the TC120. If the output short circuit is removed, normal operation is automatically restored. If the short circuit is still present, the timed self-shutdown sequence described above is repeated. DS21365C-page 6 2001-2012 Microchip Technology Inc. TC120 TABLE 3-1: SUGGESTED COMPONENTS AND SUPPLIERS Type Inductors Surface Mount Sumida CD54 Series CDRH Series Coilcraft DO Series Capacitors Diodes Transistors AVX TPS Series ON Semiconductor MBRS340T3 Silconix Little Foot MOSFET Series Sprague 595D Series Nihon NSQ Series Zetex FZT749 PNP Bipolar Transistor Matsushita MA737 Toshiba 2SA1213 PNP Transistor Miniature Through-Hole Sumida RCH Series Sanyo Standard Through-Hole Coilcraft PCH Series Nichicon PL Series OS-CON Series IRC OAR Series ON Semiconductor TMOS Power MOSFETs United Chemi-Conv LXF Series FIGURE 3-2: TC120 WITH ADDED COMPONENTS FOR IMPROVED EFFICIENCY AT HIGH OUTPUT CURRENTS VIN ≤ 5V CP 2200 pF Ceramic VIN > 5V LX VIN EXTW EXT EXTW TC120XX03 CPC D1 IN5817 SHDN/SS a) For VIN ≤ 5V 2001-2012 Microchip Technology Inc. EXT TC120XX03 GND SENSE LX VIN CP 2200 pF Ceramic CPC 10V Zener Diode D1 IN5817 SHDN/SS GND SENSE b) For VIN > 5V DS21365C-page 7 TC120 FIGURE 3-3: SHUTDOWN CONTROL CIRCUITS TC120XX03 SHDN/SS 47K SHDN 2N2222 ON OFF VIN TC120XX03 CMOS Gate R1 SHDN SHDN/SS ON OFF CSS CSS 4.7nF a) Using an Open Collector Device b) Using a Complementary Output Device VIN TC120XX03 TC120XX03 RSS SHDN/SS SHDN/SS CSS 4.7nF CSS c) Shutdown Not Used – with Pull-Up FIGURE 3-4: d) Shutdown Not Used – No Pull-Up SOFT START TIMING ON Shutdown Signal OFF 0.65V SHDN/SS X 0V 1.5msec DS21365C-page 8 2001-2012 Microchip Technology Inc. TC120 FIGURE 3-5: USING EXTERNAL TRANSISTOR SWITCH VIN CIN 47μF Tantalum LX VIN EXTW EXT TC120XX03 CPC GND L1 22μH VOUT SHDN/SS CSS 4.7 nF FIGURE 3-6: SENSE IN5817 COUT 47μF Tantalum EXTERNAL (EXT) AND EXTENDED EXTERNAL (EXTW) SWITCHING TRANSISTOR DRIVE OUTPUT EXT EXTW 100nsec 2001-2012 Microchip Technology Inc. 100nsec DS21365C-page 9 TC120 4.0 PACKAGING INFORMATION 4.1 Package Marking Information Package marking data not available at this time. 4.2 Taping Form Component Taping Orientation for 8-Pin SOP Devices User Direction of Feed PIN 1 W P Standard Reel Component Orientation for TR Suffix Device Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size 12 mm 8 mm 1000 7 in 8-Pin SOP 4.3 Package Dimensions Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 8-Pin SOP PIN 1 .181 (4.60) .165 (4.20) .256 (6.50) .232 (5.90) .051 (1.30) .049 (1.24) .217 (5.50) .193 (4.90) .069 (1.75) .055 (1.40) .020 (0.50) .012 (0.30) .008 (0.20) .000 (0.00) .010 (0.25) .004 (0.10) 8° MAX. .018 (0.45) .014 (0.35) Dimensions: inches (mm) DS21365C-page 10 2001-2012 Microchip Technology Inc. TC120 5.0 REVISION HISTORY Revision C (November 2012) Added a note to the package outline drawing. 2001-2012 Microchip Technology Inc. DS21365C-page 11 TC120 NOTES: DS21365C-page 12 2001-2012 Microchip Technology Inc. TC120 Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. Your local Microchip sales office The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 2001-2012 Microchip Technology Inc. DS21365C-page13 TC120 NOTES: DS21365C-page14 2001-2012 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. & KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2001-2012, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620767498 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2001-2012 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS21365C-page 15 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-66-152-7160 Fax: 81-66-152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS21365C-page 16 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 10/26/12 2001-2012 Microchip Technology Inc.