MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide.pdf

MB2146-261
F2MC-8FX Family LQFP-52P (0.65 mm pitch)
Header Board Operation Guide
Doc. # 002-07429 Rev. *A
Cypress Semiconductor
198 Champion Court
San Jose, CA 95134-1709
Phone (USA): 800.858.1810
Phone (Intnl): +1.408.943.2600
www.cypress.com
Copyrights
Copyrights
© Cypress Semiconductor Corporation, 2006-2016. This document is the property of Cypress Semiconductor Corporation
and its subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United
States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property
rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with
Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable
license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code
form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that
are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely
for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software
is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in
this document. Any information provided in this document, including any sample design information or programming code, is
provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test
the functionality and safety of any application made of this information and any resulting product. Cypress products are not
designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including
resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where
the failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical
component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure
of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and
hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress
products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities,
including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and
Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list
of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
2
Preface
Thank you for purchasing the LQFP-52P (0.65 mm pitch) *1 header board (model number :
MB2146-261) for the F2MC -8FX family.
MB2146-261 is a header board used to connect the MCU board (model number : MB2146-301,
MB2146-303) which mounts the F2MC-8FX family evaluation MCU to a user system.
This manual explains the handling of the MB2146-261. Before using MB2146-261, be sure to read
this manual.
Consult the Sales representatives or the Support representatives of Cypress for mass-produced
MCUs and evaluation MCUs which correspond on MB2146-261.
MB2146-261 is an object about MCU with a built-in LCD controller.
*1: The lead pitch of package (FPT-52P-M01) is 0.65 mm and the body size is 10 mm × 10 mm.
■
Caution of the products described in this document
The following precautions apply to the product described in this manual.
CAUTION
The wrong use of a device will give an injury and may cause malfunction
on customers system.
Cuts
This product has parts with sharp points that are exposed.
Do not touch an edge of the product with your bare hands.
Damage
When connecting the header board to the user system, correctly position
the index mark (▲) on the NQPACK mounted on the user system with the
1 pin direction(1) on the header board, otherwise the MCU board and user
system might be damaged.
Damage
When mounting a mass production MCU, correctly position pin 1, otherwise the mass production MCU and user system might be damaged.
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
3
Contents
1. Product Outline
1.1
1.2
5
Product Outline ............................................................................................................5
Product Configuration ..................................................................................................6
2. Checking the Delivered Product
7
3. Handling Precautions
8
4. Notes on Designing
9
4.1
4.2
Notes on designing printed circuit board for the user system ......................................9
MCU footprint design notes .......................................................................................10
5. Connecting to the User System
5.1
5.2
Connecting.................................................................................................................11
Disconnection ............................................................................................................12
6. Mounting Mass Production MCUs
6.1
6.2
13
Mounting ....................................................................................................................13
Disconnection ............................................................................................................14
7. Product Specifications
7.1
7.2
7.3
7.4
7.5
11
15
General Specifications...............................................................................................15
Main Part ...................................................................................................................15
Functional Block Diagram ..........................................................................................16
MCU Board I/F Connector (CN1, CN2, and CN3) ....................................................17
User System I/F YQPACK (U1) .................................................................................19
Revision History
20
Document Revision ..........................................................................................................................20
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
4
1.
1.1
Product Outline
Product Outline
MB2146-261 is a header board (referred to as header board) used to connect the MCU board
(model number : MB2146-301, MB2146-303) which mounts an evaluation MCU in the F2MC-8FX
family of Cypress 8-bit microcontrollers to a user system. To build an F2MC-8FX evaluation environment, combine the three products as shown in Figure 1-1: the header board, a MCU board, and a
BGM adapter (model number : MB2146-09).
For more information please visit our following websites:
www.cypress.com/documentation/development-kitsboards/mb2146-261
www.cypress.com/documentation/development-kitsboards/mb2146-09a-e
www.cypress.com/documentation/development-kitsboards/mb2146-301a-e
www.cypress.com/documentation/development-kitsboards/mb2146-303a-e
Figure 1-1. System Configuration
㪤㪙㪉㪈㪋㪍㪄㪇㪐
MCU board
BGM adapter
Header board
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
5
Product Outline
1.2
Product Configuration
Table 1-1 lists the product configuration in the header board, and Table 1-2 lists options.
Table 1-1. Product Cofiguration
Name
F2
Description
Remarks
MC-8FX
LQFP-52P (0.65 mm pitch)
Connector/LQFP52pin
header board
(0.65 mm pitch) Package conversion
-
[Model number : MB2146-261]
[Model number : YQPACK052SB]
(Tokyo Eletech Corporation)
[Model number : NQPACK052SB]
(Tokyo Eletech Corporation)
[Model number : HQPACK052SB]
(Tokyo Eletech Corporation)
I/F between header board and NQPACK Accessory (connected)
For mounted on user system
Accessory
Used when mounting mass production
MCU to NQPACK.
Accessory
Table 1-2. Options
Name
BGM adapter
[Model number : MB2146-09]
Description
ICE unit for F2MC-8FX
Remarks
-
MCU board
Built-in MB95FV100BBuilt-in F2MC-8FX evaluation MCU *
[Model number : MB2146-301, MB2146-303] 101, MB95FV100B-103
* : Multiple types of evaluation MCUs are available depending on their applications. Purchase the one
that satisfies the service conditions.
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
6
2.
Checking the Delivered Product
Before using the MB2146-261, confirm that the following components are included
in the box:
■
LQFP-52P (0.65 mm pitch) header board *1
:1
■
Screws for securing header board (M2 × 10 mm, 0.4 mm pitch)
:4
■
NQPACK052SB *2
:1
■
HQPACK052SB
*3
:1
■
Operation manual (English version, this manual)
:1
*1: Header board manufactured by Tokyo Eletech Corporation, referred to as “YQPACK”, mounts YQPACK052SB.
*2: IC socket manufactured by Tokyo Eletech Coporation, referred to as “NQPACK”, is supplied with a special screwdriver and 2 guide pins.
A socket offering higher reliability, NQPACK052SB-SL (manufactured by Tokyo Eletech Corporation and sold separately) , can be used
by making an IC socket mounting hole on the user system board. For more information, contact Tokyo Eletech Corporation.
*3: IC socket cover manufactured by Tokyo Eletech Corporation, referred to as “HQPACK”, is supplied with 4 screws for securing HQPACK
(M2 × 6 mm, 0.4 mm pitch) .
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
7
3.
Handling Precautions
The header board is precision-manufactured to improve the dimensional accuracy and to ensure a
reliable contact. The header board is therefore sensitive to mechanical shocks. To ensure a correct
use of the header board in the proper environment, observe the following:
■
Avoid placing a stress on the NQPACK mounted on the user system board when connecting the
header board.
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
8
4.
4.1
Notes on Designing
Notes on designing printed circuit board for the user system
When the header board is connected to the user system, some part mounted around the NQPACK in
the user system may be contacting the header board if the height of the part is tall. To prevent this,
design the printed circuit board for the user system so that the components do not exceed the height
shown in Figure 4-1. Figure 4-1 shows the dimension figure of the header board.
Figure 4-1. Header Board Dimensions
PCW-1-1-1PW
:MAC EIGHT
40.0 mm
30.0 mm
㪈
㪈
㪉
㪚㪥㪈
40.0 mm
㪚㪥㪉
㪉
㪚㪥㪊
㪬㪈
㪈㪈㪐
㪈㪉㪇
㪈㪈㪐
㪈㪉㪇
WR-120SB-VF-N1 : JAE *2
YQPACK052SB
:Tokyo Eletech Corporation
13.0 mm *1
Approximately
WR-120SB-VF-N1 : JAE *2
NQPACK052SB
:Tokyo Eletech Corporation
U1:
User system I/F connector
CN3:
Incorrect insertion prevention socket
CN1/CN2:
MCU board I/F connector
*1: The height differs slightly depending on how the YQPACK and NQPACK are engaged.
*2: Japan Aviation Electronics Industry, Limited
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
9
Notes on Designing
4.2
MCU footprint design notes
Figure 4-2 shows the recommended footprint dimensions of the NQPACK mounted on the printed
circuit board for the user system. Take the footprint in Figure 4-2 into consideration as well as the
footprint of the mass production MCU when designing the printed circuit board for the user system.
To follow the most updated information, be sure to contact Tokyo Eletech Corporation whenever
designing the printed circuit board.
Figure 4-2. Recommended Footprint Dimensions for Mounting the NQPACK
0.4 mm
2.0 mm
0.65 mm
13.0 mm
9.0 mm
No.1 Pin
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
10
5.
5.1
Connecting to the User System
Connecting
Mount the supplied NQPACK on the user system before using the MB2146-261.
1. To connect the header board to the user system, match pin 1 indicated by the index mark (▲) on
the NQPACK mounted on the user system with pin 1 indicated by the index mark (an angle cut
linearly at one place only in silk screen) on the header board and then insert it (see Figure 5-1) .
The pins of YQPACK are thin and easy to bend. Insert NQPACK after confirming that the pins of
YQPACK are not bent.
27
13
52
14
40
26
39
1
Figure 5-1. Index Position
NQPACK index mark
Header board index mark
2. Insert each screw for securing the header board into each of the four tapped holes on the header
board, and then tighten the screws diagonally. The center screw hole is not used. To tighten the
screws, use the special screwdriver supplied with the NQPACK to equally tighten the four screws
in sequence. Tightening the screws too tight might result in a defective contact.
3. Connect the MCU board to the header board while being careful not to excessively force the
NQPACK. The MCU board can be connected to the header board only in the correct orientation
as they have an incorrect insertion prevention header socket to prevent a reverse connection.
Figure 5 -2 illustrates how the MCU board, header board, NQPACK, and user system are
connected together.
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
11
Connecting to the User System
Figure 5-2. Connecting MCU Board/Header Board to User System
MCU board
Evaluation
MCU
MCU board
Screws for securing
header board
Header board
Connected
at shipment
YQPACK
NQPACK
User system
5.2
Disconnection
1. Remove the MCU board from the header board. Detach the four corners slowly in sequence, not
excessively forcing the junction with the NQPACK.
2. Remove all of the four screws from the header board. Pull out the header board vertically from
the NQPACK. Remove the header board slowly not excessively forcing the junction with the
NQPACK.
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
12
6.
6.1
Mounting Mass Production MCUs
Mounting
To mount a mass production MCU on the user system, use the supplied HQPACK (IC socket cover)
(see “Figure 6-1”) .
1. To mount a mass production MCU on the user system, match the index mark (▲) on the
NQPACK mounted on the user system with the index mark (●) on the mass production MCU.
2. Confirm that the mass production MCU is correctly mounted on the NQPACK. Next, match the
index mark of HQPACK with the index mark of NQPACK and insert it (angle cut linearly at one
place only) .
The pins of HQPACK are thin and easy to bend. Insert NQPACK after confirming that pins of
HQPACK are not bent.
3. Insert each screw for securing HQPACK in each of four tapped holes on the HQPACK, and then
tighten the screws diagonally. To tighten the screws, use the special screwdriver supplied with
the NQPACK to finally tighten the four screws in sequence. Tightening the screws too tight might
result in a defective contact.
Figure 6-1. Mounting a Mass Production MCU
Screws for securing HQPACK
HQPACK
Mass production MCU
NQPACK
User system
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
13
Mounting Mass Production MCUs
6.2
Disconnection
To remove the HQPACK, remove all of the four screws and pull out the HQPACK vertically from the
NQPACK. When taking out the mass production MCU, absorb the mass production MCU using a
vacuum pick-up tool special for removing IC. Do not attempt to remove the mass production MCU
forcibly, for example, using a screwdriver to do so can bend the pins of the mass production MCU or
break the NQPACK.
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
14
7.
7.1
Product Specifications
General Specifications
Table 7-1 lists the general specifications of the header board.
Table 7-1. General Specifications
Item
Description
Operating temperature and storage temperature
5°C to 35°C (operation) , 0°C to 40°C (storage)
Operating humidity and storage humidity
20 % to 80 % (operation) , 20 % to 80 % (storage)
Approximately 40 mm × 40 mm × 16 mm
Dimensions
7.2
(Height contains that of YQPACK and NQPACK)
Main Part
The main part of a header board is shown in Table 7-2.
Table 7-2. Main Part
Name
Description
120 pin, 0.5 mm pitch, 2-piece connector
MCU board I/F connector
(straight) × 2
[Model number : WR-120SB-VF-N1
(from Japan Aviation Electronics Industry, Limited) ]
2 pin, 2.54 mm pitch, 1-piece socket
Incorrect insertion prevention socket
(Straight)
[Model number : PCW-1-1-1PW (from MAC EIGHT) ]
Socket
User target system I/F connector
52 pin, 0.65 mm pitch
[Model number : YQPACK052SB (from Tokyo Eletech Corporation) ]
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
15
Product Specifications
7.3
Functional Block Diagram
A header board performs socket conversion between the MCU board I/F connector and YQPACK.
The header board does not contain any component such as an IC internally. Figure 7-1 shows the
block diagram.
Figure 7-1. Functional Block Diagram
MCU board I/F connector
User target system I/F connector
(Socket for package)
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
16
Product Specifications
7.4
MCU Board I/F Connector (CN1, CN2, and CN3)
CN1 and CN2 are MCU board I/F connectors. CN3 is the incorrect insertion prevention socket of a
MCU board. The pin assignment of the MCU board I/F connector CN1 is shown in Table 7-3, and the
pin assignment of the MCU board I/F connector CN2 is shown in Table 7-4.
Table 7-3. Pin Assignment of the MCU Board I/F Connector CN1
Connector
Pin
Number
Evaluation
MCU Pin
Number
Signal
name
Connector
Pin
Number
Evaluation
MCU Pin
Number
1
A9
PC4
41
E2
LVR3
81
P3
BSOUT
2
B9
PC1
42
E1
LVSS
82
P4
BDBMX
3
C9
PC2
43
F4
LVDREXT
83
R1
P83
4
D9
PC3
44
F3
LVDBGR
84
R2
BRSTX
5
A8
PC0
45
F2
LVDENX
85
R3
X0A
6
B8
PB4
46
F1
P22A
86
R4
RSTX
7
C8
PB5
47
-
GND
87
T1
ROMS1
8
D8
PB6
48
-
GND
88
T2
BSIN
9
A7
PB7
49
G4
P20A
89
T3
Vss
10
B7
PB2
50
G3
NC1
90
T4
X0
11
C7
PB0
51
G2
P21A
91
U1
BEXCK
12
D7
PB1
52
G1
P23A
92
U2
X1
13
A6
PB3
53
H4
P24A
93
U3
MOD
14
B6
PA2
54
H3
P25A
94
U4
PF2
15
C6
P95
55
H2
P26A
95
V1
X1A
16
D6
PA0
56
H1
P27A
96
V2
Vcc53
17
A5
PA3
57
J4
P24B
97
-
GND
18
B5
P94
58
J3
P50
98
-
GND
19
C5
P90
59
J2
P23B
99
V3
PINT0
20
D5
P91
60
J1
P51
100
V4
PSEL_EXT
21
A4
PA1
61
K1
P52
101
R5
PF1
22
A3
P93
62
K2
P55
102
T5
PF0
23
-
GND
63
K3
P54
103
U5
NC2
24
-
GND
64
K4
P53
104
V5
PENABLE
25
A2
CSVENX
65
L1
P70
105
R6
APBENX
26
A1
Vss
66
L2
P74
106
T6
PINT1
27
B4
P92
67
L3
P73
107
U6
PCLK
28
B3
TCLK
68
L4
P72
108
V6
PADDR0
PACTIVE
Signal
name
Connector
Pin
Number
Evaluation
MCU Pin
Number
Signal
name
29
B2
LVCC
69
M1
P71
109
R7
30
B1
LVDIN
70
M2
P76
110
T7
PLOCK
31
C4
Cpin
71
M3
P80
111
U7
PWRITE
32
C3
Vcc51
72
M4
P77
112
V7
PADDR1
33
C2
LVDENX2
73
-
GND
113
R8
PADDR2
34
C1
LVR4
74
-
GND
114
T8
PADDR3
35
D4
TESTO
75
N1
P75
115
U8
PADDR4
36
D3
LVDOUT
76
N2
P82
116
V8
PADDR5
37
D2
LVR2
77
N3
PG0
117
R9
PADDR7
38
D1
BGOENX
78
N4
P84
118
T9
PRDATA0
39
E4
LVR1
79
P1
P81
119
U9
PADDR6
40
E3
LVR0
80
P2
ROMS0
120
V9
PRDATA1
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
17
Product Specifications
Table 7-4. Pin Assignment of the MCU Board I/F Connector CN2
Connector
Pin
Number
Evaluation
MCU Pin
Number
Signal
name
Connector
Pin
Number
Evaluation
MCU Pin
Number
1
A10
PC5
41
E17
NC4
2
B10
PD0
42
E18
SEL0
3
C10
PC6
43
F15
SEL3
4
D10
PC7
44
F16
5
A11
PD1
45
6
B11
PD2
46
7
C11
PD3
8
D11
PD4
Connector
Pin
Number
Evaluation
MCU Pin
Number
Signal
name
81
P16
P34
82
P15
P35
83
R18
P44
SEL4
84
R17
P36
F17
SEL1
85
R16
P31
F18
P04C
86
R15
AVcc3
47
-
GND
87
T18
P40
48
-
GND
88
T17
P32
Signal
name
9
A12
PD5
49
G15
P06C
89
T16
AVss
10
B12
PD7
50
G16
P07C
90
T15
AVR
11
C12
P61
51
G17
P05C
91
U18
P33
12
D12
P60
52
G18
P00C
92
U17
P30
13
A13
PD6
53
H15
P01C
93
U16
AVR3
14
B13
P64
54
H16
P02C
94
U15
P15
15
C13
P66
55
H17
P03C
95
V18
AVcc
16
D13
P65
56
H18
P07A
96
V17
DA0
17
A14
P62
57
J15
P04A
97
-
GND
18
B14
PE0A
58
J16
P05A
98
-
GND
19
C14
PE3A
59
J17
P06A
99
V16
P14
20
D14
PE2A
60
J18
P03A
100
V15
P10
21
A15
P63
61
K18
P02A
101
R14
P16
22
A16
P67
62
K17
P07B
102
T14
DA1
23
-
GND
63
K16
P01A
103
U14
P13
24
-
GND
64
K15
P00A
104
V14
PWDATA7
25
A17
PE4A
65
L18
P06B
105
R13
P11
26
A18
Vcc54
66
L17
P05B
106
T13
P12
27
B15
PE1A
67
L16
P04B
107
U13
NC3
28
B16
PE5A
68
L15
P03B
108
V13
PWDATA3
29
B17
PE7A
69
M18
P02B
109
R12
PWDATA5
30
B18
PE3B
70
M17
P00B
110
T12
PWDATA6
31
C15
PE6A
71
M16
P46
111
U12
PWDATA4
32
C16
Vss
72
M15
P47
112
V12
PRDATA7
33
C17
PE2B
73
-
GND
113
R11
PWDATA0
34
C18
PE7B
74
-
GND
114
T11
PWDATA1
35
D15
PE1B
75
N18
P01B
115
U11
PWDATA2
36
D16
PE0B
76
N17
P43
116
V11
PRDATA6
37
D17
PE6B
77
N16
P41
117
R10
PRDATA3
38
D18
SEL2
78
N15
P42
118
T10
PRDATA4
39
E15
PE5B
79
P18
P45
119
U10
PRDATA5
40
E16
PE4B
80
P17
P37
120
V10
PRDATA2
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
18
Product Specifications
7.5
User System I/F YQPACK (U1)
The pin assignment of user system I/F YQPACK in the header board is shown in Table 7-5.
Table 7-5. Pin Assignment of the User System I/F YQPACK in Header Board
Connector
Pin Number
Signal name
Connector
Pin Number
1
P61/S09/PPG11
27
VCC
2
P62/S10/TO10
28
Cpin
3
P63/S11/TO11
29
X1A
Signal name
4
P64/S12/EC1
30
X0A
5
P65/S13/SCK
31
RSTX
6
P66/S14/SOT
32
P90/V3
7
NC
33
NC
8
P67/S15/SIN
34
P91/V2
9
P14/PPG0
35
P92/V1
10
P13/TRG0/ADTG
36
P93/V0
11
P12/UCK0
37
P94/C0
12
P11/UO0
38
P95/C1
13
P10/UI0
39
PA0/COM0
14
P07/INT07/AN07
40
PA1/COM1
15
P06/INT06/AN06
41
PA2/COM2
16
P05/INT05/AN05
42
PA3/COM3
17
P04/INT04/AN04
43
PB0/S00
18
P03/INT03/AN03
44
PB1/S01
19
P02/INT02/AN02
45
PB2/S02
20
NC
46
NC
21
P01/INT01/AN01
47
PB3/S03/PPG00
22
P00/INT00/AN00
48
PB4/S04/PPG01
23
MO
49
PB5/S05/TO00
24
X0
50
PB6/S06/TO01
25
X1
51
PB7/S07/EC0
26
VSS
52
P60/S08/PPG10
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
19
Revision History
Document Revision
Document Title: MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide
Document Number: 002-07429
Revision
**
*A
ECN#

Issue Date
Origin of
Change
Description of Change
04/25/2006
HUAL
Initial release
5282871 05/26/2016
HUAL
Migrated Spansion Guide from SS01-26015-1E to Cypress format
MB2146-261 F2MC-8FX Family LQFP-52P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07429 Rev. *A
20