INFINEON UPF01012

PRODUCT BRIEF
10 Gigabit/s Transceiver with
XAUI Interface
The TenGiPHY-L is a single chip transceiver IC
for 10 Gbit/s Ethernet and Fibre Channel connectivity. It offers a serial, full duplex 10 Gbit/s, XFI
compliant interface to optical components or to a
serial fiber-optic module (XFP). The integrated
CDR and CMU operate at a data rate of 10.3125 or
10.51875 Gbit/s. The TenGiPHY-L provides the
XGXS, PCS and PMA sublayers of the 10 Gbit/s
Ethernet and Fibre Channel standards.
At the system side, a quad serial XAUI interface
connects the TenGiPHY-L to the upper layers.
The networking system can control the chip via a
narrow-width MDIO interface by writing and reading its control and status registers.
Applications
■
■
■
■
Fiber optic modules according to
the XENPAK multi-source
agreement
10 Gbit/s Ethernet line cards
10 Gbit/s Fibre Channel line and
NIC cards
Terabit Routers
Features
■
■
■
■
■
Complete 10 Gbit/s Ethernet and
Fibre Channel PHY device supporting LAN applications
Complies with IEEE 802.3ae
Complies with ANSI 1413-D
Compliant to XENPAK multisource agreement
Embedded µController allows for
control and tuning of the PMDs
via analog interfaces
■
■
■
■
■
■
■
UPF 01012
Clock & data recovery and clock
multiplying unit without external
loop filter components
Supports various clocking
modes based on external reference clocks, loop- and external
timing
Integrated bit error rate tester
(BERT) usable for multiple atspeed diagnostic scenarios
Includes the XGXS, PCS, and
PMA sublayers of the OSI protocol stack
Synchronization and de-skewing
of XAUI lanes
Performs 8B/10B (de-)coding
required for the XGXS sublayer
Various loop back modes for
system debugging
■
■
Provides access to E²PROM via
I²C interface according to XENPAK requirements; automatic
E²PROM download on power-up
Power-efficient design:
<1.3W @ 1.3V
Interfaces
■
■
■
■
■
■
Full duplex, XFI compliant serial
CML line interface for data rates
between 10.3 and 10.5 Gbit/s
Quad serial Gbit/s XAUI interface
with data rates between 3.1 and
3.2 Gbit/s
MDIO interface
I²C interface
XENPAK diagnostic interface
providing eight 12-bit ADCs and
four 10-bit DACs
IEEE 1149.1 JTAG boundary
scan interface
UPF 01012
TenGiPHY-L
N e v e r
s t o p
t h i n k i n g .
PRODUCT BRIEF
Block Diagram
XAUI
Interface
4x 3.125
Gbit/s
Sync
Sync&&
Deskew
Deskew
BERT
BERT
8B/10B
8B/10B
CODEC
CODEC
64B/66B
64B/66B
CODEC
CODEC
Scrambler
Scrambler
Clock
Clock
Multiplier
Multiplier
Unit
Unit
Clock
Clock&&
Data
Data
Recovery
Recovery
Serial
Line
1010
GG
Serial
Line
Interface
Interface
System Interface
JTAG
JTAGInterface
Interface
Line
Interface
10.3125 Gb/s
µController
µController
I²C
I²C
Interface
Interface
XENPAK
XENPAK
Diagnostic
Diagnostic
Documentation and Support Package
■
Data Sheet
■
Hardware Evaluation System
includes mother- and transponder board
MDIO/MDC
MDIO/MDC
Interface
Interface
■
■
Alarm
Alarm
Interface
Interface
WINEASY Software for MS
Windows with graphical user
interface
Application Assistant: Configuration Software for MS Windows for
device initialization
Type
Sales Code
Package
TenGiPHY-L
UPF 01012
P-FCHBGA-177-1
Application Example
UPF 01012
Laser
LDD
10Gbps
CDR
Data
PCS
XGXS
MAC
XAUI
Interface
CMU
Clock
LA
TIA
Photodiode
Optical Module
Management
Interface
I²C
Interface
E²PROM
(optional)
10G Ethernet / Fibre Channel Line Card
How to reach us:
http://www.infineon.com
Published by
Infineon Technologies AG,
Bereich Kommunikation,
St.-Martin-Strasse 53,
D-81541 München
© Infineon Technologies AG 2002. All Rights Reserved.
Attention please!
The information herein is given to describe certain components
and shall not be considered as warranted characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not
limited to warranties of non-infringement, regarding circuits,
descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and
conditions and prices please contact your nearest
Infineon Technologies Office in Germany or our Infineon
Technologies Representatives worldwide.
Published by Infineon Technologies AG
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in question
please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in lifesupport devices or systems with the express written approval
of Infineon Technologies, if a failure of such components can
reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness
of that device or system. Life support devices or systems are
intended to be implanted in the human body, or to support
and/or maintain and sustain and/or protect human life. If they
fail, it is reasonable to assume that the health of the user or
other persons may be endangered.
Printed in Germany
PS 0502.2