10 Gigabit XFP Serial Hot-Pluggable Tr a n s c e i v e r The Infineon 10G XFP transceiver series is a family of high-performance, low-cost modules for serial optical data communication applications. The modules are protocol-agnostic, ultra-small 10 Gbit/s optical transceivers that comply with all applicable IEEE 802.3ae 10 Gigabit Ethernet and NCITS 10 Gigabit Fibre Channel standards. Infineon’s small-form-factor 10 Gigabit XFP transceivers are fully Features compliant with the specifications of the XFP MSA (Multi-Source Full-duplex transmission at 9.95 to Agreement). The XFP series includes an 850 nm wavelength version for short-reach applications of up to 300 m and a 1310 nm version for applications of up 11.08 Gbit/s Transceiver options: 850 nm VCSEL for a range up to 300 m to 10 km in range. Infineon’s XFP modules allow communications equipment manufacturers over multi-mode fiber to create standard-based, high-bandwidth systems to meet the 1310 nm DFB laser for up to 10 km over requirements of 10GE, 10GFC and OC-192 applications, including server single-mode fiber network interface cards, host bus adapters, target channel adapters Protocol-transparent and SAN and enterprise LAN switches. 2-wire interface for integrated Digital The modules are designed for high-density applications. Configurations of up to 16 modules in a 19-inch rack space are possible without Optical Monitoring Serial 10 Gbit/s XFI electrical interface compromising the stringent thermal and EMI management requirements User-friendly plug-and-play-style "Hot with 10 Gbit/s optical electronics devices. Swap” Power consumption less than 2.5 W 5 V, 3.3 V and 1.8 V power supply Applications Integrated transmit and receive CDR Fibre Channel SAN switches IEC 60825-1 class 1 and FDA 21 CFR Ethernet LAN switches 1040.10 and 1040.11 laser eye safety Fibre Channel host bus adapters ESD class 2 per MIL-STD 883D method Ethernet network interface cards 3015.7 Hubs, bridges, routers FCC 47 CFR class B SONET/SDH/ATM switches www.infineon.com/fiberoptics Never stop thinking. Products Ordering code Wave length Reach Optical connect V23833-F0005-B101 850 nm 300 m* LC V23833-F0105-B001 1310 nm 10 km LC * Using 50 µm multi-mode fiber with 2000 MHz*km bandwidth Accessories Ordering code Product Description V23833-F9909-Z001 XFP evaluation board kit Test board with 30-Pin XFP connector and cage a XFP transceiver mechanical package [mm] XFP transceiver block diagram Vcc Hot swap control Tx Rx timer ASIC SerDes/PHY XFI 9.95-11.08 Gbit/s Laser driver 10 G laser 9.95-11.08 Gbit/s Rx CDR 2 wire interface Control & data management PIN + TIA/LA 30-pin edge connector For more information, please contact: Infineon Technologies Edition September 2003 Published by Infineon Technologies AG, St.-Martin-Straße 53, D-81669 München © Infineon Technologies AG 2003. All Rights Reserved. Europe (Germany): Angela Scholl Phone: +49-30-386-22521 [email protected] Asia (Hong Kong): Owen Chui Phone: +852-2832-048 [email protected] Please note: The information herein describes certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement regarding circuits, descriptions and charts stated herein. Infineon Technologies is an approved CECC manufacturer. Information For further information on technology, delivery terms and conditions and prices, please contact your nearest Infineon Technologies office in Germany or our Infineon Technologies representatives worldwide (www.infineon.com). Japan (Tokyo): Kunikazu Watanabe Phone: +81-3-5449-6705 [email protected] Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Infineon Technologies components may only be used in life-support devices or systems with the express written approval of Infineon Technologies if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life-support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Order no. B159-H8165-G1-X-7600 Printed in Germany PS 09032. Z&P 2002921 North America (CA): Irene Yan Phone: +1-408-501-5664 [email protected]