PD - 94748A Ultra Low Dropout, 3.0A Adjustable Positive Linear Regulator Surface Mount (SMD-6) O M 7 764 AS M 5962 - 0323801MXA Product Summary Part Number Output Voltage Current Dropout OM7764ASM 1.21V to 20V 3.0A 0.4V Description SMD-6 The OM7764ASM is a 3.0A, ultra low dropout, adjustable linear regulator specifically designed for low voltage, high current applications. Housed in a hermetic package, the dropout of these devices is 400mV at full load. All protective features are designed into the circuit including thermal shutdown, current limiting and safe area control. These units are ideally suited for military/defense, commercial aircraft, industrial control and other harsh environments where a hermetically sealed package is required. Features: n n n n Dropout Voltage of 400mV at Full Load Wide Input Range: 2.7V to 20V Low Noise: 40mVRMS ( 10Hz to 10KHz ) Fast Transient Response n No Protection Diodes needed n Hermetic SMD-6 Package ensures High Reliability Absolute Maximum Ratings Parameter Symbol Value Units A Output Currrent IO 3.0 Input Voltage VIN +20 V Power Dissipation @ Tc = 25°C PD 20 W RθJC 5.0 °C/W TJ -55 to +125 TSTG TL -65 to +150 Thermal Resistance, Junction to Case Operating Junction Temperature Range Storage Temperature Range Lead Temperature Soldering (10second maximum) www.irf.com °C 300 1 10/25/06 OM7764ASM Electrical Characteristics @TA = 25°C (Unless Otherwise Specified) Parameter Test Conditions c Minimum Input voltage ILOAD = 3.0A Line Regulation ∆VIN = 2.21V to 20V, ILOAD = 1.0mA Load Regulation Adjust Pin Voltage VIN = 2.7V, ILOAD =1.0mA to 3.0A VIN = 2.7V, ILOAD =1.0mA to 3.0A 2.7V < VIN < 20V, 1.0mA < ILOAD < 3.0A c ILOAD = 1.0mA ILOAD = 100mA ILOAD = 100mA Input Reverse Leakage Current V - 2.0 10 - 5.0 15 - - 50 1.192 1.210 1.228 1.168 1.210 1.246 - 0.02 0.05 - - 0.10 - 0.07 0.13 - 0.18 0.20 - - 0.27 - 0.25 0.33 - - 0.40 ILOAD = 3.0A - 0.4 0.54 ILOAD = 3.0A - - 0.66 - 1.0 1.5 - 1.1 1.6 - 3.5 5.0 - 11 18 c c c ILOAD = 0mA c ILOAD = 1.0mA c ILOAD = 100mA c ILOAD = 500mA c ILOAD = 1.5A c ILOAD = 3.0A c VIN - VOUT = 1.5V(Average), VRIPPLE = 0.5 VP-P fRIPPLE = 120Hz, ILOAD = 1.5A, TJ = +25°C Current Limit Units 2.7 0.14 ILOAD = 1.5mA Ripple Rejection c Max. 2.3 - ILOAD = 1.5mA VIN = VOUT (Nominal)+1 c Typ. - - ILOAD = 500mA ILOAD = 500mA Ground Pin Current cd VIN = 2.21V, ILOAD =1.0mA ILOAD = 1.0mA Dropout Voltage cd Min. VIN = 2.7V, ∆VOUT = -0.1V VIN = -20V, VOUT = 0V c Reverse Output Current VOUT = 1.21V, VIN < 1.21V c c mV V mA - 40 75 - 120 200 55 65 - dB 3.1 - - A - - 1.0 mA - 300 600 µA Footnotes - Denotes specifications which apply over the full operating temperature range. - The OM7764ASM is tested and specified for these conditions with the ADJ pin connected to the OUT pin. 2 www.irf.com OM7764ASM Fig 1: Dropout Voltage Vs Temperature Fig 3: Quiescent Current Vs Input Voltage www.irf.com Fig 2: Adjust Pin Voltage Vs Temperature Fig 4: Ground Pin Current Vs Input Voltage 3 OM7764ASM Fig 5: Current Limit Vs Temperature OM7764A VIN IN R2 SHDN 0.1uF 100uF GND VOUT OUT ADJ 0.1uF 220uF R1 VOUT = 1.21V(1 + (R2/R1)) + I ADJ(R2) IADJ = 3.0uA @ 25°C Fig 6: Typical Application Layout Consideration It is recommended that output capacitors be located as close as possible to the VOUT terminal of the device to prevent any high frequency oscillation that may result due to excessive stray inductance. Specfications for capacitors: 220µF (+25V) Tantalum, 100µF (+25V) Tantalum, 0.1µF (+50V) Ceramic 4 www.irf.com OM7764ASM Case Outline and Dimensions — SMD-6 Pin Assignment Pin # Pin Description 1 INPUT 2 GROUND 3 OUTPUT 4 ADJUST 5 N/C 6 SHUTDOWN Part Numbering Nomenclature OM 7764A S M M Screening M = MIL-PRF-38535 Device Number Package Code M = SMD-6 Isolated / Non-Isolated S = Isolated www.irf.com WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 252-7105 IR LEOMINSTER: 205 Crawford St., Leominster, Massachusetts 01453, Tel: (978) 534-5776 Data and specifications subject to change without notice.10/2006 5