Freescale Semiconductor User’s Guide Document Number: KT33662UG Rev. 1.0, 8/2011 KIT33662xEFEVBE Evaluation Board Figure 1. KIT33662xEFEVBE Table of Contents 1 Kit Contents / Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 Kit Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 KIT33662xEFEVBE Setup Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6 KIT33662xEFEVBE Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 Using Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8 Board Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 9 Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 10 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 © Freescale Semiconductor, Inc., 2011. All rights reserved. Kit Contents / Packing List 1 Kit Contents / Packing List • • KIT33662JEFEVBE or KIT33662LEFEVBE Evaluation Board CD MC33662 KIT33662xEFEVBE Evaluation Board, Rev. 1.0 2 Freescale Semiconductor Important Notice 2 Important Notice Freescale provides the enclosed product(s) under the following conditions: This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and supply terminals. This EVB may be used with any development system or other source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. This EVB is not a Reference Design and is not intended to represent a final design recommendation for any particular application. Final device in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality. The goods provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end product incorporating the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical support services. Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the date of delivery and will be replaced by a new kit. Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typical”, must be validated for each customer application by customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale product could create a situation where personal injury or death may occur. Should the Buyer purchase or use Freescale products for any such unintended or unauthorized application, the Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale was negligent regarding the design or manufacture of the part.Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2011 KIT33662xEFEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 3 Kit Introduction 3 Kit Introduction This Evaluation Board is supplied for preliminary evaluation purposes. This kit is populated with a production device, and gives to you the opportunity to test the device in various configuration cases to quickly evaluate these features. This kit can also be used for Electro Static Discharge (ESD) and Bulk Current Injection (BCI) tests. 3.1 Evaluation Board Features • • • • • • 3.2 Individually routed power supply inputs for VDD and VBAT Status of product indicated by an LED Slave or master configuration via a switch Wake button Mode selector via a switch Test point for every pin Device Description/Features • • • • • • • • • • Operational from a VSUP of 7.0 to 18 V DC, functional up to 27 V DC, and handles 40 V during Load Dump Compatible with LIN Protocol Specification 1.3, 2.0, 2.1, and SAEJ2602-2 Active bus wave shaping, offering excellent radiated emission performance Sustains up to 15.0 kV minimum ESD IEC61000-4-2 on the LIN Bus, WAKE, and VSUP pins Very high immunity against electromagnetic interference Low standby current in Sleep mode Over-temperature protection Local and remote wake-up capability reported by the RXD pin Fast baud rate mode selection reported by RXD 5.0 and 3.3 V compatible digital inputs without any required external components KIT33662xEFEVBE Evaluation Board, Rev. 1.0 4 Freescale Semiconductor Required Equipment 4 Required Equipment To use this kit you need: • • • +12 VDC power supply +5.0 VDC power supply 0/+5.0 V waveform generator KIT33662xEFEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 5 KIT33662xEFEVBE Setup Configuration 5 KIT33662xEFEVBE Setup Configuration +5V KIT33662JEFEVBE OR KIT3662LEFEVBE Figure 1. KIT33662xEFEVBE Setup Configuration Diagram KIT33662xEFEVBE Evaluation Board, Rev. 1.0 6 Freescale Semiconductor Freescale Semiconductor TXD RXD EN 1 2 3 BORVIS J4 Rz3 0R R10 0R TXD KSCG S_WAKE SW1 SW_Mode R11 0R GND WAKE EN R3 8K2 RXD VBAT R7 2K2 R6 18K R5 18K VDD C5 100nF/100V WK 4 3 2 1 TXD WAKE EN RXD U1 33662 GND 5 GND Rz4 0R R9 2K2 GND SH3 0 C2 100nF/100V 8 INH INH VSUP VSUP 7 LIN 6 LIN INH L_INH GREEN LED LIN INH C6 68pF Rz6 0R Rz5 0R R8 1K BORVIS J5 D5 1N4148WS VSUP 1 2 VDD D8 MM3Z10VT1G D7 MMBZ27VCLT1 Rz7 0R SH1 0R VSUP R1 8K2 + 3 2 VDD C7 100pF/100V INH GND LIN VSUP 1 C1 330UF VSUP C3 4.7µF/10V Rz1 0R L_VSUP RED LED J2 C4 100nF/10V Rz2 0R Rz8 INH 0 BORVIS + R2 2K2 J3 BORVIS J1 L_VDD RED LED BORVIS GND Vbat WAKE D1 MBRS1100T3G 6 R4 2K2 L_EN Green LED VDD SW2 SW_LIN KIT33662xEFEVBE Schematic KIT33662xEFEVBE Schematic Figure 2. KIT33662xEFEVBE Schematic KIT33662xEFEVBE Evaluation Board, Rev. 1.0 7 Using Hardware 7 Using Hardware 7.1 Jumper Connections RZ1 RZ2 RZ3 RZ4 RZ5 RZ6 RZ7 RZ8 R10 R11 SW1 SW2 SW3 SH1 SH3 LED for VSUP state LED for VDD state LED for EN state LED for INH state enable SW2 add C6 on LIN bus add D7 on LIN bus can be change to add load on INH BUS can be change to limit current on EN pin (1) can be change to limit current on EN pin (1) connect EN pin to: • VDD (1) • EN connector (2) • GND (3) add load on LIN bus and set Master/slave configuration: • connected to VSUP (1)(Master configuration 1) • unconnected (2)(Slave configuration) • INH (3)(Master Configuration 2) connect the WAKE pin to GND slot to change the load value on LIN bus slot to change the load value on LIN bus Note: 1. In this case, RZ3 must be unsoldered to have 5.0 V on the EN pin KIT33662xEFEVBE Evaluation Board, Rev. 1.0 8 Freescale Semiconductor Board Layout 8 Board Layout 8.1 Assembly Top Layer Figure 3. Assembly Top Layer KIT33662xEFEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 9 Board Layout 8.2 Top Layer Routing Figure 4. Top Layer Routing KIT33662xEFEVBE Evaluation Board, Rev. 1.0 10 Freescale Semiconductor Board Layout 8.3 Bottom Layer Routing Figure 5. Bottom Layer Routing KIT33662xEFEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 11 Bill of Material 9 Bill of Material Table 1. KIT33662xEFEVBE Bill of Material (2) Quantity Part Reference Device or Value Description Freescale Components 1 U1 MC33662JEF or MC33662LEF 10kbps baud rate 20kbps baud rate 1 U2 Socket SOIC8 socket - LIN Transceiver 1 C1 330 µF/100 V CAP ALEL 20% - RADIAL 2 C2, C5 100 nF/100 V CAP CER 10% - X7R 0805 1 C3 4.7 µF/10 V CAP ALEL 20% - RADIAL 1 C4 100 nF/10 V CAP CER 10% - X7R 0805 1 C6 68 pF/100 V CAP CER 10% - X7R 0805 1 C7 100 pF/100 V CAP CER 10% - X7R 0805 2 R1, R3 8.2 K RES TF 1/8 W 5% - RC0805 4 R2, R4, R7, R9 2.2 K RES TF 1/8 W 1% - RC0805 2 R5, R6 18 k RES TF 1/8 W 1% - RC0805 R8 1.0 K RES TF 1/8 W 5% 2 R10, R11 0 RES 0 - RC0805 8 RZ1, RZ2, RZ3, RZ4, RZ5, RZ6, RZ7, RZ8 0 RES 0 - RC0805 1 D1 MBRS1100T3G Schottky 1.0 A 100 V - SMB 1 D5 1N4148WS DIODE 150 mA 53 V - SOD-323 1 D7 MMBZ27VCLT1 Dual Common Cathode Zeners - SOT-23 1 D8 MM3Z10VT1G Zener 10 V 5% 200 mW - SOD-323 2 L_INH, L_EN LXT0805GW LED GREEN 20MA 2 L_VDD, L_VSUP LXT0805RW LED RED 20MA 3 J1, J3, J5 PCB 2WAY 250 V/16 A CON 2 2 J2, J4 PCB 3WAY 250 V/16 A CON 3 2 SW1, SW2 TG39P0 20 V/0.4 A SPDT ON-OFF-ON 1 S-WAKE KSC221J 32 V/50 mA SW SPST SMT Capacitors Resistors Diode Connectors Note: 2. Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer’s responsibility to validate their application KIT33662xEFEVBE Evaluation Board, Rev. 1.0 12 Freescale Semiconductor References 10 References Following are locations where you can obtain information on other Freescale products and application solutions. Description URL Reference Web Sites Reference URL Locations MC33662 Data Sheet http://www.freescale.com/files/analog/doc/data_sheet/MC33662.pdf Application Notes http://www.freescale.com/files/analog/doc/app_note/AN2409.pdf Freescale’s Web Site http://www.freescale.com Freescale’s Analog and Power Management Web site http://www.freescale.com/analog Freescale’s Automotive Applications Web site http://www.freescale.com/automotive KIT33662xEFEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 13 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 [email protected] Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further to products herein. Freescale Semiconductor makes no warranty, representation or regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, be validated for each customer application by technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Qorivva, S12 MagniV, SMARTMOS and Xtrinsic are trademarks of Freescale Semiconductor, Inc. ARM is the registered trademark of ARM Limited. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. All other product or service names are the property of their respective owners. ©2011 Freescale Semiconductor, Inc. KT33662UG Rev. 1.0 8/2011