PHILIPS TDA1524A

INTEGRATED CIRCUITS
DATA SHEET
TDA1524A
Stereo-tone/volume control circuit
Product specification
File under Integrated Circuits, IC01
September 1987
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
GENERAL DESCRIPTION
The device is designed as an active stereo-tone/volume control for car radios, TV receivers and mains-fed equipment.
It includes functions for bass and treble control, volume control with built-in contour (can be switched off) and balance.
All these functions can be controlled by d.c. voltages or by single linear potentiometers.
Features
• Few external components necessary
• Low noise due to internal gain
• Bass emphasis can be increased by a double-pole low-pass filter
• Wide power supply voltage range.
QUICK REFERENCE DATA
Supply voltage (pin 3)
VP = V3-18
typ.
12
V
Supply current (pin 3)
IP = I3
typ.
35
mA
Vi(rms)
typ.
2,5
V
3
V
Maximum input signal with
d.c. feedback (r.m.s. value)
Maximum output signal with
Vo(rms)
typ.
Volume control range
d.c. feedback (r.m.s. value)
Gv
−80 to + 21,5
dB
Bass control range at 40 Hz
∆Gv
−19 to + 17
dB
Treble control range at 16 kHz
∆Gv
typ.
±15
dB
Total harmonic distortion
THD
typ.
0,3
%
for max. voltage gain
Vno(rms)
typ.
310
µV
for voltage gain Gv = −40 dB
Vno(rms)
typ.
100
µV
αcs
typ.
60
dB
Output noise voltage (unweighted; r.m.s. value)
at f = 20 Hz to 20 kHz; VP = 12 V;
Channel separation
at Gv = −20 to + 21,5 dB
Tracking between channels
at Gv = −20 to + 26 dB
∆Gv
max.
2,5
dB
Ripple rejection at 100 Hz
RR
typ.
50
dB
Supply voltage range (pin 3)
VP = V3-18
7,5 to 16,5
V
Operating ambient temperature range
Tamb
−30 to + 80
°C
PACKAGE OUTLINE
18-lead DIL; plastic (SOT102); SOT102-1; 1996 July 22.
September 1987
2
Stereo-tone/volume control circuit
September 1987
3
Fig.1 Block diagram and application circuit with single-pole filter.
(1) Series resistor is recommended in the event of the capacitive loads exceeding 200 pF.
Philips Semiconductors
Product specification
TDA1524A
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
Fig.2 Double-pole low-pass filter for improved bass-boost.
Fig.3 D.C. feedback with filter network for improved signal handling.
September 1987
4
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
Supply voltage (pin 3)
VP = V3-18 max.
Total power dissipation
Ptot
Storage temperature range
Tstg
−55 to + 150 °C
Operating ambient temperature range
Tamb
−30 to +80 °C
max.
20 V
1200 mW
D.C. CHARACTERISTICS
VP = V3-18 = 12 V; Tamb = 25 °C; measured in Fig.1; RG ≤ 600 Ω; RL ≥ 4,7 kΩ; CL ≤ 200 pF; unless otherwise specified
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Supply (pin 3)
VP = V3-18
7,5
−
16,5
V
at VP = 8,5 V
IP = I3
19
27
35
mA
at VP = 12 V
IP = I3
25
35
45
mA
at VP = 15 V
IP = I3
30
43
56
mA
Supply voltage
Supply current
D.C. input levels (pins 4 and 15)
at VP = 8,5 V
V4,15-18
3,8
4,25
4,7
V
at VP = 12 V
V4,15-18
5,3
5,9
6,6
V
at VP = 15 V
V4,15-18
6,5
7,3
8,2
V
at VP = 8,5 V
V8,11-18
3,3
4,25
5,2
V
at VP = 12 V
V8,11-18
4,6
6,0
7,4
V
at VP = 15 V
V8,11-18
5,7
7,5
9,3
V
V17-18
3,5
3,75
4,0
V
contour (switch open)
−I17
−
−
0,5
mA
linear (switch closed)
−I17
1,5
−
10
mA
V17-18
4,5
−
VP/2−VBE
V
D.C. output levels (pins 8 and 11)
under all control voltage conditions
with d.c. feedback (Fig.3)
Pin 17
Internal potentiometer supply voltage
at VP = 8,5 V
Contour on/off switch (control by I17)
Application without internal potentiometer
supply voltage at VP ≥ 10,8 V
(contour cannot be switched off)
Voltage range forced to pin 17
September 1987
5
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
PARAMETER
TDA1524A
SYMBOL
MIN.
TYP.
MAX.
UNIT
D.C. control voltage range for volume,
bass, treble and balance
(pins 1, 9, 10 and 16 respectively)
at V17-18 = 5 V
V1,9,10,16
1,0
−
4,25
V
using internal supply
V1,9,10,16
0,25
−
3,8
V
−I1,9,10,16
−
−
5
µA
Input current of control inputs
(pins 1,9,10 and 16)
A.C. CHARACTERISTICS
VP = V3-18 = 8,5 V; Tamb = 25 °C; measured in Fig.1; contour switch closed (linear position); volume, balance, bass, and
treble controls in mid-position; RG ≤ 600 Ω; RL ≥ 4,7 kΩ; CL ≤ 200 pF; f = 1 kHz; unless otherwise specified
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Control range
Max. gain of volume (Fig.5)
Gv max
20,5
21,5
23
dB
Volume control range; Gv max/Gv min
∆Gv
90
100
−
dB
Balance control range; Gv = 0 dB (Fig.6)
∆Gv
−
−40
−
dB
Bass control range at 40 Hz (Fig.7)
∆Gv
−
−19 to + 17 ± 3
dB
Treble control range at 16 kHz (Fig.8)
∆Gv
−
± 15 ± 3
−
dB
Control characteristics
see Fig.9 and 10
Signal inputs, outputs
Input resistance; pins 4 and 15 (note 1)
at gain of volume control:Gv = 20 dB
Gv = −40 dB
Output resistance (pins 8 and 11)
Ri4,15
10
−
−
kΩ
Ri4,15
−
160
−
kΩ
Ro8,11
−
−
300
Ω
RR
35
50
−
dB
αcs
46
60
−
dB
∆Gv
−
−
±3
dB
∆Gv,L-R
−
−
1,5
dB
∆Gv
−
−
2,5
dB
Signal processing
Power supply ripple rejection
at VP(rms) ≤ 200 mV; f = 100 Hz; Gv = 0 dB
Channel separation (250 Hz to 10 kHz)
at Gv = −20 to + 21,5 dB
Spread of volume control with
constant control voltage V1-18 = 0,5 V17-18
Gain tolerance between left and right
channel V16-18 = V1-18 = 0,5 V17-18
Tracking between channels
for Gv = 21,5 to −26 dB
f = 250 Hz to 6,3 kHz; balance adjusted at
Gv = 10 dB
September 1987
6
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Signal handling with d.c. feedback (Fig.3)
Input signal handling
at VP = 8,5 V; THD = 0,5%;
Vi(rms)
1,4
−
−
V
Vi(rms)
1,8
2,4
−
V
Vi(rms)
1,4
−
−
V
Vi(rms)
2,0
3,2
−
V
Vi(rms)
1,4
−
−
V
Vi(rms)
2,0
3,2
−
V
Vo(rms)
1,8
2,0
−
V
Vo(rms)
−
2,2
−
V
Vo(rms)
2,5
3,0
−
V
Vo(rms)
−
3,5
−
V
for maximum voltage gain (note 4)
Vno(rms)
−
260
−
µV
for Gv = −3 dB (note 4)
Vno(rms)
−
70
140
µV
Vno(m)
−
890
−
µV
Vno(m)
−
360
−
µV
f = 1 kHz (r.m.s. value)
at VP = 8,5 V; THD = 0,7%;
f = 1 kHz (r.m.s. value)
at VP = 12 V; THD = 0,5%;
f = 40 Hz to 16 kHz (r.m.s. value)
at VP = 12 V; THD = 0,7%;
f = 40 Hz to 16 kHz (r.m.s. value)
at VP = 15 V; THD = 0,5%;
f = 40 Hz to 16 kHz (r.m.s. value)
at VP = 15 V; THD = 0,7%;
f = 40 Hz to 16 kHz (r.m.s. value)
Output signal handling (note 2 and note 3)
at VP = 8,5 V; THD = 0,5%;
f = 1 kHz (r.m.s. value)
at VP = 8,5 V; THD = 10%;
f = 1 kHz (r.m.s. value)
at VP = 12 V; THD = 0,5%;
f = 40 Hz to 16 kHz (r.m.s. value)
at VP = 15 V; THD = 0,5%;
f = 40 Hz to 16 kHz (r.m.s. value)
Noise performance (VP = 8,5 V)
Output noise voltage (unweighted; Fig.15)
at f = 20 Hz to 20 kHz (r.m.s. value)
Output noise voltage; weighted as DIN 45405
of 1981, CCIR recommendation 468-2 (peak value)
for maximum voltage gain (note 4)
for maximum emphasis of bass and treble
(contour off; Gv = −40 dB)
September 1987
7
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Noise performance (VP = 12 V)
Output noise voltage (unweighted; Fig.15)
at f = 20 Hz to 20 kHz (r.m.s. value; note 5)
for maximum voltage gain (note 4)
Vno(rms)
−
310
−
µV
for Gv = −16 dB (note 4)
Vno(rms)
−
100
200
µV
Vno(m)
−
940
−
µV
Vno(m)
−
400
−
µV
for maximum voltage gain (note 4)
Vno(rms)
−
350
−
µV
for Gv = 16 dB (note 4)
Vno(rms)
−
110
220
µV
Vno(m)
−
980
−
µV
Vno(m)
−
420
−
µV
Output noise voltage; weighted as DIN 45405
of 1981, CCIR recommendation 468-2 (peak value)
for maximum voltage gain (note 4)
for maximum emphasis of bass and treble
(contour off; Gv = −40 dB)
Noise performance (VP = 15 V)
Output noise voltage (unweighted; Fig.15)
at f = 20 Hz to 20 kHz (r.m.s. value; note 5)
Output noise voltage; weighted as DIN 45405
of 1981, CCIR recommendation 468-2 (peak value)
for maximum voltage gain (note 4)
for maximum emphasis of bass and treble
(contour off; Gv = −40 dB
Notes to characteristics
1. Equation for input resistance (see also Fig.4)
160 kΩ
R i = ------------------- ;G vmax = 12
1 + Gv
2. Frequencies below 200 Hz and above 5 kHz have reduced voltage swing, the reduction at 40 Hz and at 16 kHz is
30%.
3. In the event of bass boosting the output signal handling is reduced. The reduction is 1 dB for maximum bass boost.
4. Linear frequency response.
5. For peak values add 4,5 dB to r.m.s. values.
September 1987
8
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
Fig.4 Input resistance (Ri) as a function of gain of volume control (Gv). Measured in Fig.1.
Fig.5
Volume control curve; voltage gain (Gv) as a function of control voltage (V1-18). Measured in Fig.1
(internal potentiometer supply from pin 17 used); VP = 8,5 V; f = 1 kHz.
September 1987
9
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
Fig.6
Balance control curve; voltage gain (Gv) as a function of control voltage (V16-18). Measured in Fig.1
(internal potentiometer supply from pin 17 used); VP = 8,5 V.
Fig.7
Bass control curve; voltage gain (Gv) as a function of control voltage (V9-18). Measured in Fig.1 with
single-pole filter (internal potentiometer supply from pin 17 used); VP = 8,5 V; f = 40 Hz.
September 1987
10
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
Fig.8
TDA1524A
Treble control curve; voltage gain (Gv) as a function of control voltage (V10-18). Measured in Fig.1
(internal potentiometer supply from pin 17 used); VP = 8,5 V; f = 16 kHz.
Fig.9
September 1987
Contour frequency response curves; voltage gain (Gv) as a function of audio input frequency.
Measured in Fig.1 with single-pole filter; VP = 8,5 V.
11
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
Fig.10 Contour frequency response curves; voltage gain (Gv) as a function of audio input frequency.
Measured in Fig.1 with double-pole filter; VP = 8,5 V.
Fig.11 Tone control frequency response curves; voltage gain (Gv) as a function of audio input frequency.
Measured in Fig.1 with single-pole filter; VP = 8,5 V.
September 1987
12
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
Fig.12 Tone control frequency response curves; voltage gain (Gv) as a function of audio input frequency.
Measured in Fig.1 with double-pole filter; VP = 8,5 V.
Fig.13 Total harmonic distortion (THD); as a function of audio input frequency. Measured in Fig.1; VP = 8,5 V;
volume control voltage gain at
Vo
G v = 20 log ------ = 0 dB.
Vi
September 1987
13
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
Fig.14 Total harmonic distortion (THD); as a function of output voltage (Vo). Measured in Fig.1;
VP = 8,5 V; fi = 1 kHz.
(1) VP = 15 V.
(2) VP = 12 V.
(3) VP = 8,5 V.
Fig.15 Noise output voltage (Vno(rms); unweighted); as a function of voltage gain (Gv).
Measured in Fig.1; f = 20 Hz to 20 kHz.
September 1987
14
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
PACKAGE OUTLINE
DIP18: plastic dual in-line package; 18 leads (300 mil)
SOT102-1
ME
seating plane
D
A2
A
A1
L
c
e
Z
w M
b1
(e 1)
b
b2
MH
10
18
pin 1 index
E
1
9
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
b2
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
4.7
0.51
3.7
1.40
1.14
0.53
0.38
1.40
1.14
0.32
0.23
21.8
21.4
6.48
6.20
2.54
7.62
3.9
3.4
8.25
7.80
9.5
8.3
0.254
0.85
inches
0.19
0.020
0.15
0.055
0.044
0.021
0.015
0.055
0.044
0.013
0.009
0.86
0.84
0.26
0.24
0.10
0.30
0.15
0.13
0.32
0.31
0.37
0.33
0.01
0.033
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
93-10-14
95-01-23
SOT102-1
September 1987
EUROPEAN
PROJECTION
15
Philips Semiconductors
Product specification
Stereo-tone/volume control circuit
TDA1524A
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
September 1987
16