MIC5205 150mA Low-Noise LDO Regulator General Description Features The MIC5205 is an efficient linear voltage regulator with ultra low-noise output, very low dropout voltage (typically 17mV at light loads and 165mV at 150mA), and very low ground current (600⎧A at 100mA output). The MIC5205 offers better than 1% initial accuracy. Designed especially for hand-held, battery-powered devices, the MIC5205 includes a CMOS or TTL compatible enable/shutdown control input. When shut down, power consumption drops nearly to zero. Regulator ground current increases only slightly in dropout, further prolonging battery life. Key MIC5205 features include a reference bypass pin to improve its already excellent low-noise performance, reversed-battery protection, current limiting, and overtemperature shutdown. The MIC5205 is available in fixed and adjustable output voltage versions in a small SOT-23-5 package. For low-dropout regulators that are stable with ceramic output capacitors, see the µCap MIC5245/6/7 family. Data sheets and support documentation can be found on Micrel’s web site at www.micrel.com. • • • • • • • • • • • Ultra-low-noise output High output voltage accuracy Guaranteed 150mA output Low quiescent current Low dropout voltage Extremely tight load and line regulation Very low temperature coefficient Current and thermal limiting Reverse-battery protection “Zero” off-mode current Logic-controlled electronic enable Applications • • • • • • • Cellular telephones Laptop, notebook, and palmtop computers Battery-powered equipment PCMCIA VCC and VPP regulation/switching Consumer/personal electronics SMPS post-regulator/dc-to-dc modules High-efficiency linear power supplies ___________________________________________________________________________________________________________ Typical Application Ultra-Low-Noise Regulator Application Xxxxx is a trademark of Micrel, Inc Xxxxx is a registered trademark of Micrel, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com February 2006 M9999-020806 (408) 955-1690 Micrel MIC5205 Ordering Information Part Number Standard Marking Pb-Free Standard Pb-Free(1) Accuracy Voltage Temperature Package MIC5205BM5 MIC5205YM5 LBAA KBAA 1% Adj –40°C to +125°C SOT-23-5 MIC5205-2.5BM5 MIC5205-2.5YM5 LB25 KB25 1% 2.5V –40°C to +125°C SOT-23-5 MIC5205-2.7BM5 MIC5205-2.7YM5 LB27 KB27 1% 2.7V –40°C to +125°C SOT-23-5 MIC5205-2.8BM5 MIC5205-2.8YM5 LB28 KB28 1% 2.8V –40°C to +125°C SOT-23-5 MIC5205-2.85BM5 MIC5205-2.85YM5 LB2J KB2J 1% 2.85V –40°C to +125°C SOT-23-5 MIC5205-2.9BM5 MIC5205-2.9YM5 LB29 KB29 1% 2.9V –40°C to +125°C SOT-23-5 MIC5205-3.0BM5 MIC5205-3.0YM5 LB30 KB30 1% 3.0V –40°C to +125°C SOT-23-5 MIC5205-3.1BM5 MIC5205-3.1YM5 LB31 KB31 1% 3.1V –40°C to +125°C SOT-23-5 MIC5205-3.2BM5 MIC5205-3.2YM5 LB32 KB32 1% 3.2V –40°C to +125°C SOT-23-5 MIC5205-3.3BM5 MIC5205-3.3YM5 LB33 KB33 1% 3.3V –40°C to +125°C SOT-23-5 MIC5205-3.6BM5 MIC5205-3.6YM5 LB36 KB36 1% 3.6V –40°C to +125°C SOT-23-5 MIC5205-3.8BM5 MIC5205-3.8YM5 LB38 KB38 1% 3.8V –40°C to +125°C SOT-23-5 MIC5205-4.0BM5 MIC5205-4.0YM5 LB40 KB40 1% 4.0V –40°C to +125°C SOT-23-5 MIC5205-5.0BM5 MIC5205-5.0YM5 LB50 KB50 1% 5.0V –40°C to +125°C SOT-23-5 Note: 1. Underbar (_) symbol may not be to scale. Pin Configuration MIC5205-x.xBM5/YM5 Fixed Voltages MIC5205BM5/YM5 Adjustable Voltages Pin Description MIC5205-x.x (fixed) MIC5205 (adjustable) Pin Name Pin Function 1 1 IN Supply Input 2 2 GND 3 3 EN February 2006 Enable/Shudown (Input): CMOS compatible input. Logic high = enable, logic low or open = shutdown BYP Reference Bypass: Connect external 470pF capacitor to GND to reduce output noise. May be left open. 4 ADJ Adjust (Input): Adjustable regulator feedback input. Connect to resistor voltage divider. 5 OUT Regulator Ouput 4 5 Ground 2 M9999-020806 (408) 955-1690 Micrel MIC5205 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Input Voltage (VIN).............................. –20V to +20V Enable Input Voltage (VEN)............................. –20V to +20V Power Dissipation (PD) .................Internally Limited, Note 3 Lead Temperature (soldering, 5 sec.)........................ 260°C Junction Temperature (TJ) ........................–40°C to +125°C Storage Temperature (TS).........................–65°C to +150°C Input Voltage (VIN)......................................... +2.5V to +16V Enable Input Voltage (VEN).....................................0V to VIN Junction Temperature (TJ) ........................ –40°C to +125°C Thermal Resistance, SOT-23-5 (θJA) ........................ Note 3 Electrical Characteristics(4) VIN = VOUT + 1V; IL = 100µA; CL = 1.0µF; VEN ≥ 2.0V; TJ = 25°C, bold values indicate –40°C ≤ TJ ≤ +125°C; unless noted. Symbol Parameter Condition Min Typ VO Output Voltage Accuracy variations from specified VOUT ∆VO/∆T Output Voltage Temperature Coefficient Note 4 ∆VO/VO Line Regulation VIN = VOUT + 1V to 16V 0.004 0.012 0.05 %/V %/V ∆VO/VO Load Regulation IL = 0.1mA to 150mA, Note 5 0.02 0.2 0.5 % % VIN – VO Dropout Voltage, Note 6 IL = 100µA 10 IL = 50mA 110 IL = 100mA 140 IL = 150mA 165 50 70 150 230 250 300 275 350 mV mV mV mV mV mV mV mV –1 –2 Max Units 1 2 % % ppm/°C 40 IGND Quiescent Current VEN ≤ 0.4V (shutdown) VEN ≤ 0.18V (shutdown) 0.01 1 5 µA µA IGND Ground Pin Current, Note 7 VEN ≥ 2.0V, IL = 100µA 80 IL = 50mA 350 IL = 100mA 600 IL = 150mA 1300 125 150 600 800 1000 1500 1900 2500 µA µA µA µA µA µA µA µA 500 mA PSRR Ripple Rejection Frequency = 100Hz, IL = 100µA 75 ILIMIT Current Limit VOUT = 0V 320 ∆VO/∆PD Thermal Regulation Note 8 0.05 eNO Output Noise IL = 50mA, CL = 2.2µF, 470pF from BYP to GND 260 dB %/W nV/ Hz ENABLE Input VIL Enable Input Logic-Low Voltage regulator shutdown VIH Enable Input Logic-High Voltage regulator enabled IIL Enable Input Current VIL ≤ 0.4V VIL ≤ 0.18V VIL = 2.0V VIL = 2.0V IIH February 2006 0.4 0.18 2.0 V 0.01 2 3 V V 5 –1 –2 20 25 µA µA µA µA M9999-020806 (408) 955-1690 Micrel MIC5205 Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. The maximum allowable power dissipation at any TA (ambient temperature) is PD(max) = (TJ(max) – TA) ⎟ ⎝JA. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. The ⎝JA of the MIC5205-xxBM5 (all versions) is 220°C/W mounted on a PC board (see “Thermal Considerations” section for further details). 4. Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. 5. Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 0.1mA to 150mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification. 6. Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. 7. Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. 8, Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 150mA load pulse at VIN = 16V for t = 10ms. February 2006 4 M9999-020806 (408) 955-1690 Micrel MIC5205 Typical Characteristics February 2006 5 M9999-020806 (408) 955-1690 Micrel MIC5205 Typical Characteristics February 2006 6 M9999-020806 (408) 955-1690 Micrel MIC5205 Block Diagrams Ultra-Low-Noise Fixed Regulator Ultra-Low-Noise Adjustable Regulator February 2006 7 M9999-020806 (408) 955-1690 Micrel MIC5205 0.33µF for currents below 1mA. Application Information No-Load Stability The MIC5205 will remain stable and in regulation with no load (other than the internal voltage divider) unlike many other voltage regulators. This is especially important in CMOS RAM keep-alive applications. Enable/Shutdown Forcing EN (enable/shutdown) high (> 2V) enables the regulator. EN is compatible with CMOS logic gates. If the enable/shutdown feature is not required, connect EN (pin 3) to IN (supply input, pin 1). See Figure 1. Thermal Considerations The MIC5205 is designed to provide 150mA of continuous current in a very small package. Maximum power dissipation can be calculated based on the output current and the voltage drop across the part. To determine the maximum power dissipation of the package, use the junction-to-ambient thermal resistance of the device and the following basic equation: Input Capacitor A 1µF capacitor should be placed from IN to GND if there is more than 10 inches of wire between the input and the ac filter capacitor or if a battery is used as the input. Reference Bypass Capacitor BYP (reference bypass) is connected to the internal voltage reference. A 470pF capacitor (CBYP) connected from BYP to GND quiets this reference, providing a significant reduction in output noise. CBYP reduces the regulator phase margin; when using CBYP, output capacitors of 2.2µF or greater are generally required to maintain stability. The start-up speed of the MIC5205 is inversely proportional to the size of the reference bypass capacitor. Applications requiring a slow ramp-up of output voltage should consider larger values of CBYP. Likewise, if rapid turn-on is necessary, consider omitting CBYP. If output noise is not a major concern, omit CBYP and leave BYP open. PD(max) = θ JA TJ(max) is the maximum junction temperature of the die, 125°C, and TA is the ambient operating temperature. θJA is layout dependent; Table 1 shows examples of junction-toambient thermal resistance for the MIC5205. Package θJA θJA Square Recommended Copper Clad Minimum Footprint SOT-23-5(M5) 220°C/W 170°C/W Table 1. SOT-23-5 Thermal Resistance θJC 130°C/W The actual power dissipation of the regulator circuit can be determined using the equation: PD = (VIN – VOUT) IOUT + VIN IGND Substituting PD(max) for PD and solving for the operating conditions that are critical to the application will give the maximum operating conditions for the regulator circuit. For example, when operating the MIC5205-3.3BM5 at room temperature with a minimum footprint layout, the maximum input voltage for a set output current can be determined as follows: Output Capacitor An output capacitor is required between OUT and GND to prevent oscillation. The minimum size of the output capacitor is dependent upon whether a reference bypass capacitor is used. 1.0µF minimum is recommended when CBYP is not used (see Figure 2). 2.2µF minimum is recommended when CBYP is 470pF (see Figure 1). Larger values improve the regulator’s transient response. The output capacitor value may be increased without limit. The output capacitor should have an ESR (effective series resistance) of about 5Ω or less and a resonant frequency above 1MHz. Ultra-low-ESR capacitors can cause a low amplitude oscillation on the output and/or underdamped transient response. Most tantalum or aluminum electrolytic capacitors are adequate; film types will work, but are more expensive. Since many aluminum electrolytics have electrolytes that freeze at about – 30°C, solid tantalums are recommended for operation below –25°C. At lower values of output current, less output capacitance is required for output stability. The capacitor can be reduced to 0.47⎧F for current below 10mA or February 2006 (TJ(max) − TA ) PD(max) = (125°C − 25°C) 220°C/W PD(max) = 455mW The junction-to-ambient thermal resistance for the minimum footprint is 220°C/W, from Table 1. The maximum power dissipation must not be exceeded for proper operation. Using the output voltage of 3.3V and an output current of 150mA, the maximum input voltage can be determined. From the Electrical Characteristics table, the maximum ground current for 150mA output current is 2500µA or 2.5mA. 455mW = (VIN – 3.3V) 150mA + VIN·2.5mA 455mW = VIN×150mA – 495mW + VIN·2.5mA 950mW = VIN×152.5mA 8 M9999-020806 (408) 955-1690 Micrel MIC5205 resistors set the output voltage based on the following equation: VIN(max) = 6.23V Therefore, a 3.3V application at 150mA of output current can accept a maximum input voltage of 6.2V in a SOT23-5 package. For a full discussion of heat sinking and thermal effects on voltage regulators, refer to the Regulator Thermals section of Micrel’s Designing with Low-Dropout Voltage Regulators handbook. ⎛ R2 ⎞ VOUT = 1.242V × ⎜ + 1⎟ ⎝ R1 ⎠ This equation is correct due to the configuration of the bandgap reference. The bandgap voltage is relative to the output, as seen in the block diagram. Traditional regulators normally have the reference voltage relative to ground and have a different VOUT equation. Resistor values are not critical because ADJ (adjust) has a high input impedance, but for best results use resistors of 470kΩ or less. A capacitor from ADJ to ground provides greatly improved noise performance. Fixed Regulator Applications Figure 1. Ultra-Low-Noise Fixed Voltage Application Figure 1 includes a 470pF capacitor for low-noise operation and shows EN (pin 3) connected to IN (pin 1) for an application where enable/shutdown is not required. COUT = 2.2µF minimum. Figure 3. Ultra-Low-Noise Adjustable Voltage Application Figure 3 includes the optional 470pF noise bypass capacitor from ADJ to GND to reduce output noise. Figure 2. Low-Noise Fixed Voltage Application Dual-Supply Operation When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must be diode clamped to ground. Figure 2 is an example of a low-noise configuration where CBYP is not required. COUT = 1µF minimum. Adjustable Regulator Applications The MIC5205BM5 can be adjusted to a specific output voltage by using two external resistors (Figure 3). The February 2006 9 M9999-020806 (408) 955-1690 Micrel MIC5205 Package Information SOT-23-5 (M5) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2004 Micrel, Incorporated. February 2006 10 M9999-020806 (408) 955-1690