Optoway TRML-7100CG 1 *********************************************************************************************************************************************************************** TRML-7100CG / TRML-7100ACG 3.3V / 850 nm / 1.25 Gbps RoHS Compliant SFF LC MULTI-MODE TRANSCEIVER ********************************************************************************************************************************************************************** FEATURES DESCRIPTION l Duplex LC Multi-Mode Transceiver l Compliant with IEEE 802.3z 1000BASE-SX l Compliant with Fibre Channel FC-PH-2 for 100-M5-SN-1 and 100-M6-SN-1 l 300 m links with 62.5/125 µm MMF Cables l 500 m links with 50/125 µm MMF Cables l Small Form Factor 2X5 pin Package l AC/AC Coupled Signal Input / Output l LVTTL Transmitter Disable Input l LVTTL Signal Detect Output l Single +3.3 V Power Supply l RoHS Compliant l 0 to 70oC Operation : TRML-7100CG l -20 to 85oC Operation : TRML-7100ACG l Wave Solderable and Aqueous Washable l Class 1 Laser International Safety Standard IEC-60825 Compliant The TRML-7100CG series multi-mode transceivers is small form factor, low power, high performance module for bi-directional serial optical data communications such as Gigabit Ethernet IEEE 802.3z 1000BASE-SX and Fiber Channel FC-PH-2. This module is designed for multi-mode fiber and operates at a nominal wavelength of 850 nm. The transmitter section uses a multiple quantum well 850 nm VCSEL and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated GaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry. APPLICATIONS l SONET/SDH Equipment Interconnect l Gigabit Ethernet 1.25 Gb/s Links LASER SAFETY This multi-mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ORDER INFORMATION P/No. TRML-7100CG TRML-7100ACG Bit Rate (Gb/s) 1000 BASE 1.25/1.063 1.25/1.063 SX SX Distance Wavelength (m) (nm) Package Temp. (oC) 300/500* 300/500* 2X5 LC 2X5 LC 0 to 70 -20 to 85 850 850 TX Power RX Sens. RoHS (dBm) (dBm) Compliant -4 to -9 -17 Yes -4 to -9 -17 Yes Note: 300 m links with 62.5/125 µm MMF Cables and 500 m links with 62.5/125 µm MMF Cables. Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Symbol Tstg Topr Soldering Temperature Power Supply Voltage Input Voltage --Vcc --- Output Current Iout Min -40 0 -20 Units o C o C 0 GND Max 85 70 85 260 4.5 Vcc 0 30 mA Min 3.13 0 -20 1000 Typ 3.3 Max 3.47 70 85 o C V V Notes TRML-7100CG TRML-7100ACG 10 seconds on leads only Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Symbol Vcc Topr Data Rate Power Supply Current Icc 1250 180 250 Units / Notes V o C / TRML-7100CG o C / TRML-7100ACG Mb/s mA ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway TRML-7100CG 2 *********************************************************************************************************************************************************************** Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Electrical Data Input Current – Low Data Input Current – High Differential Input Voltage Data Input Voltage – Low Data Input Voltage -- High Disable Input Voltage -- Low Disable Input Voltage -- High Shut Off Time for TxDis Symbol Min Typ Max Units Notes Po -9 830 λ --∆λ ER 9 Compliant with IEEE 802.3z tr tf RIN TJ --850 ----- -4 860 0.85 --- dBm nm nm dB 1 0.26 0.26 -116 0.226 ns ns dB/Hz ns IIL IIH VIH - V IL VIL - V CC VIH - V CC VTDIS,L VTDIS,H tDIS -350 350 300 -2.0 -1.1 0 Vcc – 1.3 -1.58 -0.74 0.8 Vcc 1 µA µA mV V V V V ms RMS (σ) 20% to 80% Values 20% to 80% Values 2 3 3 TX Output Enabled TX Ouput Disabled Notes: 1. Output power is power coupled into a 62.5/125 µm MM fiber. 2. Measured with a 27-1 PRBS. 3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs. Receiver Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3.47V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Electrical Data Output Voltage – Low Data Output Voltage – High Signal Detect Output Voltage -- Low Signal Detect Output Voltage -- High Symbol Min Typ Max Units Notes --Pin Pa Pd ---3 ---31 1.0 1100 --0 --------- -17 ---17 --- dBm dBm dBm dBm dB nm 1 VOL - VCC VOH - VCC VOL VOH -2.0 -1.1 1600 -1.58 -0.74 0.5 2.0 V V V V Transition: low to high Transition: high to low 2 2 Notes: 1. Minimum sensitivity and saturation levels at BER=1E-12 for a 27-1 PRBS. 2. These outputs are compatible with 10K, 10KH and 100K ECL and PECL outputs. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway TRML-7100CG 3 *********************************************************************************************************************************************************************** CONNECTION DIAGRAM PIN 1 2 3 4 5 6 7 8 Symbol VEEr VCC r SD RD− RD+ VCC t VEEt TDis 9 10 MS TD+ TDMS Notes Directly connect this pin to the receiver ground plane +3.3V dc power for the receiver section Active high on this indicates a received optical signal. Receiver Dataout Bar. See recommended circuit schematic Receiver Dataout. See recommended circuit schematic +3.3V dc power for the transmitter section Directly connect this plan to the transmitter ground plane Transmitter Disable. Connect this pin to +3.3V TTL logic “1” to disable module To enable module connect to TTL logic low “0” Transmitter Data In. See recommended circuit schematic Transmitter Data In Bar. See recommended circuit schematic Mounting Studs. Connect to Chassis Ground RECOMMENDED CIRCUIT SCHEMATIC Vcc3.3V TDZ=50R TD+ LVPECL TDTD+ TDis Veet Vcct TXDis(LVTTL) 10 9 8 7 6 Z=5OR Vcc3.3V 1uH 10nF 10nF 10uF 10uF PHY DEVICE 1 2 3 4 5 Veer Vccr SD RDRD+ 1uH 10nF Vcc3.3V 10uF RD+ 100R LVPECL Z=50R RDZ=5OR SD TO LVTTL STAGE Note: 1. No SD pull-down resistor required for TRML-7100CG (LVTTL SD Output) 2. Veer and Veet are not internally connected to each other. 3. 50 Ω line pattern and component placements on TD+/TD- and RD+/RD- lines shall be symmetrical for better impedance matching. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway TRML-7100CG 4 *********************************************************************************************************************************************************************** PACKAGE DIAGRAM Units in mm 1) Standard Case TRML-7100CG / TRML-7100ACG 2) Extended Case TRML-7100CEG / TRML-7100ACEG Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0