Data Sheet 100VAC Input/12VDC (350mA) Output Non-Isolated AC/DC Converter BP5067-12 Absolute Maximum Ratings Unit V mApk kV °C °C 9.9MAX. 34.5MAX. Mark Side Limits 190 350 2 −20 to +80 −25 to +105 22.0MAX. Symbol Vi IoMAX Vsurge Topr Tstg 1 4±1.0 Parameter Input voltage Maximum output current ESD endurance Operating temperature range Storage temperature range Dimensions (Unit : mm) 3 5 0 . 5 ±0 . 1 10 12 7.62 1.3±0.2 5.08 3.3MAX 7 2.54�11=27.94 0.25±0.05 5.05MAX. 4.85MAX. Electrical Characteristics Symbol Min. 113 Vi 11.0 Vo 0 Io −0.30 Vr −0.30 Vl − Vp 70 η Typ. 141 12.0 − 0.05 0.05 0.07 80 Max. 190 13.0 350 0.30 0.30 0.15 − Conditions Unit V V mA V V Vp-p % DC(80 to 135VAC) Vi=141V, Io=350mA Vi=141V Vi=113 to 190V, Io=350mA Vi=141V, Io=0 to 350mA Vi=141V, Io=350mA Vi=141V, Io=350mA Derating Curve ∗1 ∗2 Derating Curve 400 350 300 250 200 Operation Range 150 100 50 0 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Ambient Temperature Ta(°C) Output Current Io(mA) Parameter Input voltage Output voltage Output current Line regulation Load regulation Output ripple voltage Power conversion efficiency ∗1 Maximum output current varies depending on ambient temperature ; please refer to derating curve. ∗2 Please refer to Load regulation, Conversion efficiency. D1 100V 50/60Hz 7 5 3 1 FUSE R1 + ZNR 220V − C1 Io C3 L1 + 1mH − C2 Vo Please verify operation and characteristics in the customer's circuit before actual usage. Ensure that the load current does not exceed the maximum rating. External Component Specifications FUSE: Fuse Use a quick-acting fuse of (1A) above 200V, 33 to 220µF Ripple current 0.13Arms or above. C2: Output capacitor above 25V, 100 to 470µF, low impedance ESR : 0.4Ω Max. Ripple current 0.25Arms or above Capacitor impedance affects the output ripple voltage. above 200V, 0.1 to 0.22µF Use a film or ceramic capacitor. Evaluate under actual conditions. C3: Noise reduction capacitor L1: Power inductor 50 100 150 200 250 300 350 Output Current Io(mA) Load Regulation (Ta=25°C, Vi=141V) 12 10 8 6 4 2 0 50 100 150 200 250 300 350 400 450 500 550 Output Current Io(mA) D1: Rectifier diode Inductance : 1mH, Rating current : above 750mA Select a components that does not become magnetically saturated at high tempertures. Use a rectifying diode with a peak reverse voltage of 400V or higher, an average rectification current of 0.5A or larger and a peak surge current of 20A or larger. When using a large capacitance input capacitor, select a component strong against inrush current during power up. Full-wave rectification can be used. R1: Noise reduction resistor 10 to 22Ω, 1/4W The ideal value can be determined through actual testing. ZNR: Varistor A varistor must be used to protect against lightning surges and static electricity. www.rohm.com ©2010 ROHM Co., Ltd. All rights reserved. 0 14 20 C1: Input capacitor Conversion Efficiency (Ta=25°C, Vi=141V) Load Regulation Output Voltage Vo(V) 12 10 DC motor 100 90 80 70 60 50 40 30 20 10 0 1/1 Surface Temperature Increase Temperature Rising ∆T(°C) BP5067-12 Be sure to use fuse for safety. Function Pin No. 1 Output terminal Vo(12V) 2 Skip 3 Choke coil connect 4 Skip 5 Choke coil connect 6 Skip 7 COMMON 8 Skip 9 Skip 10 N.C. 11 Skip 12 Input terminal Vi(141VDC) Conversion Efficiency η(%) Conversion Efficiency Application Circuit 40 35 30 25 20 15 10 5 0 Surface Temperature Increase (Ta=25°C, Vi=141V) 0 50 100 150 200 250 300 350 Output Current Io(mA) 2010.01 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A