Data Sheet 100VAC Input/−15VDC (800mA) Output Non-Isolated AC/DC Converter BP5068-15 Dimensions (Unit : mm) Limits −190 800 2 −20 to +80 −25 to +105 Unit V mApk kV °C °C 11.3MAX. 34.5MAX. 21.5MAX. Symbol Vi Io Vsurge Topr Tstg 1 4±1.0 Parameter Input voltage Output current ESD endurance Operating temperature range Storage temperature range Mark Side Absolute Maximum Ratings 3 5 7 8 10 12 0.25±0.05 0 . 5 ±0 . 1 1 . 3 ±0 . 2 3.25MAX 7.35MAX. P=2.54 ±0.2 2.54 11=27.94 + 3.95MAX. Electrical Characteristics ∗1 Maximum output current varies depending on ambient temperature ; please refer to derating curve. ∗2 Please refer to Load regulation, Conversion efficiency. Conditions DC Vi= −141V, Io=800mA ∗1 Vi= −141V Vi= −120 to −162V, Io=800mA Vi= −141V, Io=0 to 800mA ∗2 Vi= −141V, Io=800mA ∗2 Vi= −141V, Io=800mA BP5068-15 Please note that pin No.12 side is input. 12 10 R1 D2 1SR35-400A 2.2Ω1/4W Input AC100V 50Hz/60Hz ZNR − C1 220V + 100µF/200V 8 7 5 3 FUSE 2A 1 Output −15V C2 L1 470µH − C3 0.1µF D1 + 470µF/50V Function Output terminal Vo(−15V) Skip Coil connect Skip Coil connect Skip COMMON COMMON Skip N.C. Skip Input terminal Vi(−141VDC) Be sure to use fuse for safety. Please verify operation and characteristics in the customer's circuit before actual usage. Ensure that the load current does not exceed the maximum rating. External Component Specifications FUSE: Fuse C1: Input capacitor C2: Noise reduction capacitor Use a quick-acting fuse (2A) Above 200V, 47 to 220µF Ripple current 0.22Arms above Above 200V, 0.1 to 0.22µF Use a film or ceramic capacitor. Evaluate under actual operating conditions. C3: Output capacitor Above 35V, 330 to 1000µF, low impedance ESR : 0.08Ω Max. Ripple current 1Arms or above Capacitor impedance affects the output ripple voltage. L1: Power inductor Inductance : 470µH, Rating current : above1.6A Select components that do not easily get magnetically saturated at high temperature. Above 400V, current : above 3A Fast recovery diode. Please note that both the switching and efficiency characteristics of the module are affected by this diode. Recommended products : 31DF4 (Nihon Inter) Use a rectifying diode with a peak reverse voltage of 400V or higher, an average rectification current of 1A or larger and a peak surge current of 20A or larger. When using a large capacitance input capacitor, select a component that is strong against inrush current during power up. Full-wave rectification can be used. D1: Flywheel diode D2: Rectifier diode R1: Noise reduction resistor ZNR: Varistor Derating Curve 1.0 0.9 0.8 0.7 0.6 0.5 Operation Range 0.4 0.3 0.2 0.1 0 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Ambient Temperature Ta(°C) Conversion Efficiency Application Circuit Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Derating Curve Output Current Io(A) Unit V V mA V V Vp-p % Conversion Efficiency η(%) Max. −162 −16.0 800 0.45 0.75 0.30 − Conversion Efficiency (Ta=25°C, Vi= −141V) 100 80 60 40 20 0 0 200 400 600 Output Current Io(mA) 800 Load Regulation Output Voltage Vo(V) Typ. −141 −15.0 − 0.20 0.50 0.15 85 16.0 15.8 15.6 15.4 15.2 15.0 14.8 14.6 14.4 14.2 14.0 Load Regulation (Ta=25°C, Vi= −141V) 0 200 400 600 Output Current Io(mA) 800 Surface Temperature Increase Temperature Rising ∆T(°C) Parameter Symbol Min. Input voltage range Vi −120 Output voltage Vo −14.0 Output current Io 0 Line regulation Vr − Load regulation Vl − Output ripple voltage Vp − Power conversion efficiency η 80 40 35 30 25 20 15 10 5 0 0 Surface Temperature Increase (Ta=25°C, Vi= −141V) 200 400 600 Output Current Io(mA) 800 1.0 to 2.2Ω, 1/4W Determine the ideal value through actual testing. A varistor is required to protect against lightning surges and static electricity. www.rohm.com ©2010 ROHM Co., Ltd. All rights reserved. 1/1 2010.01 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A