PHILIPS SC16C750B

SC16C750B
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Rev. 03 — 13 December 2004
Product data
1. General description
The SC16C750B is a Universal Asynchronous Receiver and Transmitter (UART)
used for serial data communications. Its principal function is to convert parallel data
into serial data, and vice versa. The UART can handle serial data rates up to 3 Mbit/s.
The SC16C750B is pin compatible with the TL16C750 and it will power-up to be
functionally equivalent to the 16C450. Programming of control registers enables the
added features of the SC16C750B. Some of these added features are the 64-byte
receive and transmit FIFOs, automatic hardware flow control. The selectable
auto-flow control feature significantly reduces software overload and increases
system efficiency while in FIFO mode by automatically controlling serial data flow
using RTS output and CTS input signals. The SC16C750B also provides DMA mode
data transfers through FIFO trigger levels and the TXRDY and RXRDY signals.
On-board status registers provide the user with error indications, operational status,
and modem interface control. System interrupts may be tailored to meet user
requirements. An internal loop-back capability allows on-board diagnostics.
The SC16C750B operates at 5 V, 3.3 V and 2.5 V, the industrial temperature range
and is available in plastic PLCC44, LQFP64, and HVQFN32 packages.
2. Features
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Single channel
5 V, 3.3 V and 2.5 V operation
5 V tolerant inputs
Industrial temperature range (−40 °C to +85 °C)
After reset, all registers are identical to the typical 16C450 register set
Capable of running with all existing generic 16C450 software
Pin compatibility with the industry-standard ST16C450/550, TL16C450/550,
PC16C450/550. Software compatible with SC16C750 and TL16C750
Up to 3 Mbit/s transmit/receive operation at 5 V, 2 Mbit/s at 3.3 V, and 1 Mbit/s at
2.5 V
64 byte transmit FIFO
64 byte receive FIFO with error flags
Programmable auto-RTS and auto-CTS
◆ In auto-CTS mode, CTS controls transmitter
◆ In auto-RTS mode, RxFIFO contents and threshold control RTS
Automatic hardware flow control
Software selectable Baud Rate Generator
Four selectable Receive interrupt trigger levels
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
■ Standard modem interface
■ Sleep mode
■ Standard asynchronous error and framing bits (Start, Stop, and Parity Overrun
Break)
■ Independent receiver clock input
■ Transmit, Receive, Line Status, and Data Set interrupts independently controlled
■ Fully programmable character formatting:
◆ 5, 6, 7, or 8-bit characters
◆ Even, Odd, or No-Parity formats
◆ 1, 11⁄2, or 2-stop bit
◆ Baud generation (DC to 3 Mbit/s)
■ False start-bit detection
■ Complete status reporting capabilities
■ 3-State output TTL drive capabilities for bi-directional data bus and control bus
■ Line Break generation and detection
■ Internal diagnostic capabilities:
◆ Loop-back controls for communications link fault isolation
■ Prioritized interrupt system controls
■ Modem control functions (CTS, RTS, DSR, DTR, RI, DCD).
3. Ordering information
Table 1:
Ordering information
Industrial: VCC = 2.5 V, 3.3 V or 5 V ± 10%; Tamb = −40 °C to +85 °C.
Type number
Package
Name
Description
Version
SC16C750BIA44
PLCC44
plastic leaded chip carrier; 44 leads
SOT187-2
SC16C750BIB64
LQFP64
plastic low profile quad flat package; 64 leads; 10 × 10 × 1.4 mm
SOT314-2
SC16C750BIBS
HVQFN32
plastic thermal enhanced very thin quad flat package; no leads;
32 terminals; body 5 × 5 × 0.85 mm
SOT617-1
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
2 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
4. Block diagram
SC16C750B
TRANSMIT
FIFO
REGISTERS
D0–D7
IOR, IOR
IOW, IOW
RESET
TRANSMIT
SHIFT
REGISTER
TX
RECEIVE
SHIFT
REGISTER
RX
DATA BUS
AND
CONTROL LOGIC
A0–A2
CS0, CS1, CS2
AS
REGISTER
SELECT
LOGIC
INTERCONNECT BUS LINES
AND
CONTROL SIGNALS
FLOW
CONTROL
LOGIC
RECEIVE
FIFO
REGISTERS
FLOW
CONTROL
LOGIC
DDIS
DTR
RTS
OUT1, OUT2
MODEM
CONTROL
LOGIC
INT
TXRDY
RXRDY
INTERRUPT
CONTROL
LOGIC
CTS
RI
DCD
DSR
CLOCK AND
BAUD RATE
GENERATOR
002aaa588
XTAL1
RCLK
XTAL2
BAUDOUT
Fig 1. Block diagram.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
3 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
5. Pinning information
40 CTS
41 DSR
42 DCD
43 RI
44 VCC
1 n.c.
2 D0
3 D1
4 D2
5 D3
6 D4
5.1 Pinning
D5
7
39 RESET
D6
8
38 OUT1
D7
9
37 DTR
RCLK 10
36 RTS
RX 11
35 OUT2
SC16C750BIA44
n.c. 12
34 n.c.
TX 13
33 INT
AS 28
TXRDY 27
DDIS 26
IOR 25
29 A2
IOR 24
BAUDOUT 17
n.c. 23
30 A1
GND 22
CS2 16
IOW 21
31 A0
IOW 20
CS1 15
XTAL2 19
32 RXRDY
XTAL1 18
CS0 14
002aaa589
25 CTS
27 VCC
26 DSR
28 D0
29 D1
30 D2
32 D4
terminal 1
index area
31 D3
Fig 2. PLCC44 pin configuration.
D5
1
24 RESET
D6
2
23 OUT
D7
3
22 DTR
RCLK
4
RX
5
TX
6
19 RXRDY
CS
7
18 A0
BAUDOUT
8
17 A1
21 RTS
SC16C750BIBS
20 INT
A2 16
IOR 14
TXRDY 15
GND 13
n.c. 12
IOW 11
XTAL2 10
XTAL1
9
(top view)
002aaa949
Fig 3. HVQFN32 pin configuration (top view).
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
4 of 44
SC16C750B
Philips Semiconductors
49 n.c.
50 D5
51 D6
52 D7
53 n.c.
54 RCLK
55 RX
56 n.c.
57 n.c.
58 TX
59 CS0
60 n.c.
61 CS1
62 CS2
63 n.c.
64 BAUDOUT
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
XTAL1 1
48 D4
XTAL2 2
47 n.c.
n.c. 3
46 D3
IOW 4
45 D2
n.c. 5
44 n.c.
IOW 6
43 D1
n.c. 7
42 D0
GND 8
41 n.c.
SC16C750BIB64
IOR 9
40 VCC
IOR 10
39 n.c.
n.c. 11
38 RI
DDIS 12
37 n.c.
RESET 32
n.c. 31
OUT1 30
n.c. 29
DTR 28
n.c. 27
RTS 26
OUT2 25
n.c. 24
33 CTS
INT 23
n.c. 16
n.c. 22
34 n.c.
RXRDY 21
AS 15
A0 20
35 DSR
n.c. 19
n.c. 14
A1 18
36 DCD
A2 17
TXRDY 13
002aaa590
Fig 4. LQFP64 pin configuration.
5.2 Pin description
Table 2:
Pin description
Symbol
Pin
Type
Description
PLCC44 LQFP64
HVQFN32
A2-A0
29, 30,
31
17, 18, 20
16, 17, 18 I
Register select. A0-A2 are used during read and write operations
to select the UART register to read from or write to. Refer to Table 3
for register addresses and refer to AS description.
AS
28
15
-
I
Address strobe. When AS is active (LOW), A0, A1, and A2 and
CS0, CS1, and CS2 drive the internal select logic directly; when AS
is HIGH, the register select and chip select signals are held at the
logic levels they were in when the LOW-to-HIGH transition of AS
occurred.
BAUDOUT 17
64
8
O
Baud out. BAUDOUT is a 16× clock signal for the transmitter
section of the UART. The clock rate is established by the reference
oscillator frequency divided by a divisor specified in the baud
generator divisor latches. BAUDOUT may also be used for the
receiver section by tying this output to RCLK.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
5 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 2:
Pin description…continued
Symbol
Pin
PLCC44 LQFP64
Type
Description
I
Chip select. When CS0 and CS1 are HIGH and CS2 is LOW, these
three inputs select the UART. When any of these inputs are inactive,
the UART remains inactive (refer to AS description).
HVQFN32
CS0, CS1, 14, 15,
CS2
16
59, 61, 62
-
CS
-
-
7
I
CTS
40
33
25
I
D7-D0
9-2
52, 51, 50, 3-1, 32-28 I/O
48, 46, 45,
43, 42
Data bus. Eight data lines with 3-State outputs provide a
bi-directional path for data, control and status information between
the UART and the CPU.
DCD
42
36
-
I
Data carrier detect. DCD is a modem status signal. Its condition
can be checked by reading bit 7 (DCD) of the modem status
register. Bit 3 (∆DCD) of the modem status register indicates that
DCD has changed states since the last read from the modem status
register. If the modem status interrupt is enabled when DCD
changes levels, an interrupt is generated.
DDIS
26
12
-
O
Driver disable. DDIS is active (LOW) when the CPU is not reading
data. When active, DDIS can disable an external transceiver.
DSR
41
35
26
I
Data set ready. DSR is a modem status signal. Its condition can be
checked by reading bit 5 (DSR) of the modem status register. Bit 1
(∆DSR) of the modem status register indicates DSR has changed
levels since the last read from the modem status register. If the
modem status interrupt is enabled when DSR changes levels, an
interrupt is generated.six
DTR
37
28
22
O
Data terminal ready. When active (LOW), DTR informs a modem
or data set that the UART is ready to establish communication. DTR
is placed in the active level by setting the DTR bit of the modem
control register. DTR is placed in the inactive level either as a result
of a Master Reset, during loop mode operation, or clearing the DTR
bit.
INT
33
23
20
O
Interrupt. When active (HIGH), INT informs the CPU that the UART
has an interrupt to be serviced. Four conditions that cause an
interrupt to be issued are: a receiver error, received data that is
available or timed out (FIFO mode only), an empty transmitter
holding register or an enabled modem status interrupt. INT is reset
(deactivated) either when the interrupt is serviced or as a result of a
Master Reset.
n.c.
34
3, 5, 7, 11, 12
14, 16, 19,
22, 24, 27,
29, 31, 34,
37, 39, 41,
44, 47, 49,
53, 56, 57,
60, 63
-
Not connected.
Clear to send. CTS is a modem status signal. Its condition can be
checked by reading bit 4 (CTS) of the modem status register. Bit 0
(∆CTS) of the modem status register indicates that CTS has
changed states since the last read from the modem status register.
If the modem status interrupt is enabled when CTS changes levels
and the auto-CTS mode is not enabled, an interrupt is generated.
CTS is also used in the auto-CTS mode to control the transmitter.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
6 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 2:
Pin description…continued
Symbol
Pin
Type
Description
Outputs 1 and 2. These are user-designated output terminals that
are set to the active (low) level by setting respective modem control
register (MCR) bits (OUT1 and OUT2). OUT1 and OUT2 are set to
inactive the (HIGH) level as a result of Master Reset, during loop
mode operations, or by clearing bit 2 (OUT1) or bit 3 (OUT2) of the
MCR.
PLCC44 LQFP64
HVQFN32
OUT1,
OUT2
38, 35
30, 25
-
O
OUT
-
-
23
O
RCLK
10
54
4
I
Receiver clock. RCLK is the 16× baud rate clock for the receiver
section of the UART.
RESET
39
32
24
I
Master Reset. When active (HIGH), RESET clears most UART
registers and sets the levels of various output signals.
IOR
25
10
-
I
IOR
24
9
14
I
Read inputs. When either IOR or IOR is active (LOW or HIGH,
respectively) while the UART is selected, the CPU is allowed to
read status information or data from a selected UART register. Only
one of these inputs is required for the transfer of data during a read
operation; the other input should be tied to its inactive level (i.e.,
IOR tied LOW or IOR tied HIGH).
RI
43
38
-
I
Ring indicator. RI is a modem status signal. Its condition can be
checked by reading bit 6 (RI) of the modem status register. Bit 2
(∆RI) of the modem status register indicates that RI has transitioned
from a LOW to a HIGH level since the last read from the modem
status register. If the modem status interrupt is enabled when this
transition occurs, an interrupt is generated.
RTS
36
26
21
O
Request to send. When active, RTS informs the modem or data
set that the UART is ready to receive data. RTS is set to the active
level by setting the RTS modem control register bit and is set to the
inactive (HIGH) level either as a result of a Master Reset or during
loop mode operations or by clearing bit 1 (RTS) of the MCR. In the
auto-RTS mode, RTS is set to the inactive level by the receiver
threshold control logic.
RXRDY
32
21
19
O
Receiver ready. Receiver direct memory access (DMA) signaling is
available with RXRDY. When operating in the FIFO mode, one of
two types of DMA signaling can be selected using the FIFO control
register bit 3 (FCR[3]). When operating in the 16C450 mode, only
DMA mode 0 is allowed. Mode 0 supports single-transfer DMA in
which a transfer is made between CPU bus cycles. Mode 1
supports multi-transfer DMA in which multiple transfers are made
continuously until the receiver FIFO has been emptied. In DMA
mode 0 (FCR0 = 0 or FCR0 = 1, FCR3 = 0), when there is at least
one character in the receiver FIFO or receiver holding register,
RXRDY is active (LOW). When RXRDY has been active but there
are no characters in the FIFO or holding register, RXRDY goes
inactive (HIGH). In DMA mode 1 (FCR0 = 1, FCR3 = 1), when the
trigger level or the time-out has been reached, RXRDY goes active
(LOW); when it has been active but there are no more characters in
the FIFO or holding register, it goes inactive (HIGH).
RX
11
55
5
I
Serial data input. RX is serial data input from a connected
communications device.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
7 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 2:
Pin description…continued
Symbol
Pin
Type
Description
PLCC44 LQFP64
HVQFN32
TX
13
58
6
O
Serial data output. TX is composite serial data output to a
connected communication device. TX is set to the marking (HIGH)
level as a result of Master Reset.
TXRDY
27
13
15
O
Transmitter ready. Transmitter DMA signaling is available with
TXRDY. When operating in the FIFO mode, one of two types of
DMA signaling can be selected using FCR[3]. When operating in
the 16C450 mode, only DMA mode 0 is allowed. Mode 0 supports
single-transfer DMA in which a transfer is made between CPU bus
cycles. Mode 1 supports multi-transfer DMA in which multiple
transfers are made continuously until the transmit FIFO has been
filled.
VCC
44
40
27
Power 2.5 V, 3 V or 5 V supply voltage.
GND
22
8
13
Power Ground voltage.
IOW
21
6
-
I
IOW
20
4
11
I
XTAL1
18
1
9
I
Crystal connection or External clock input.
XTAL2[1]
19
2
10
O
Crystal connection or the inversion of XTAL1 if XTAL1 is
driven.
[1]
Write inputs. When either IOW or IOW is active (LOW or HIGH,
respectively) and while the UART is selected, the CPU is allowed to
write control words or data into a selected UART register. Only one
of these inputs is required to transfer data during a write operation;
the other input should be tied to its inactive level (i.e., IOW tied LOW
or IOW tied HIGH).
In sleep mode, XTAL2 is left floating.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
8 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
6. Functional description
The SC16C750B provides serial asynchronous receive data synchronization,
parallel-to-serial and serial-to-parallel data conversions for both the transmitter and
receiver sections. These functions are necessary for converting the serial data
stream into parallel data that is required with digital data systems. Synchronization for
the serial data stream is accomplished by adding start and stop bits to the transmit
data to form a data character (character orientated protocol). Data integrity is insured
by attaching a parity bit to the data character. The parity bit is checked by the receiver
for any transmission bit errors. The SC16C750B is fabricated with an advanced
CMOS process to achieve low drain power and high speed requirements.
The SC16C750B is an upward solution that provides 64 bytes of transmit and receive
FIFO memory, instead of none in the 16C450, or 16 in the 16C550. The SC16C750B
is designed to work with high speed modems and shared network environments that
require fast data processing time. Increased performance is realized in the
SC16C750B by the larger transmit and receive FIFOs. This allows the external
processor to handle more networking tasks within a given time. In addition, the four
selectable levels of FIFO trigger interrupt and automatic hardware flow control is
uniquely provided for maximum data throughput performance, especially when
operating in a multi-channel environment. The combination of the above greatly
reduces the bandwidth requirement of the external controlling CPU, increases
performance, and reduces power consumption.
The SC16C750B is capable of operation up to 3 Mbit/s with a 48 MHz external clock
input (at 5 V).
The rich feature set of the SC16C750B is available through internal registers.
Automatic hardware flow control, selectable transmit and receive FIFO trigger level,
selectable TX and RX baud rates, modem interface controls, and a sleep mode are
some of these features.
6.1 Internal registers
The SC16C750B provides 12 internal registers for monitoring and control. These
registers are shown in Table 3. These twelve registers are similar to those already
available in the standard 16C550. These registers function as data holding registers
(THR/RHR), interrupt status and control registers (IER/ISR), a FIFO control register
(FCR), line status and control registers (LCR/LSR), modem status and control
registers (MCR/MSR), programmable data rate (clock) control registers (DLL/DLM),
and a user accessible scratchpad register (SPR). Register functions are more fully
described in the following paragraphs.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
9 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 3:
A2
Internal registers decoding
A1
A0
READ mode
WRITE mode
General register set (THR/RHR, IER/ISR, MCR/MSR, FCR, LSR, SPR)[1]
0
0
0
Receive Holding Register
Transmit Holding Register
0
0
1
Interrupt Enable Register
Interrupt Enable Register
0
1
0
Interrupt Status Register
FIFO Control Register
0
1
1
Line Control Register
Line Control Register
1
0
0
Modem Control Register
Modem Control Register
1
0
1
Line Status Register
n/a
1
1
0
Modem Status Register
n/a
1
1
1
Scratchpad Register
Scratchpad Register
Baud rate register set (DLL/DLM)[2]
0
0
0
LSB of Divisor Latch
LSB of Divisor Latch
0
0
1
MSB of Divisor Latch
MSB of Divisor Latch
[1]
[2]
These registers are accessible only when LCR[7] is a logic 0.
These registers are accessible only when LCR[7] is a logic 1.
6.2 FIFO operation
The 64-byte transmit and receive data FIFOs are enabled by the FIFO Control
Register bit-0 (FCR[0]). The receiver FIFO section includes a time-out function to
ensure data is delivered to the external CPU. An interrupt is generated whenever the
Receive Holding Register (RHR) has not been read following the loading of a
character or the receive trigger level has not been reached.
Table 4:
Flow control mechanism
Selected trigger level
(characters)
INT pin activation
Negate RTS
Assert RTS
1
1
1
0
4
4
4
0
8
8
8
0
14
14
14
0
1
1
1
0
16
16
16
0
32
32
32
0
56
56
56
0
16-byte FIFO
64-byte FIFO
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
10 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
6.3 Hardware flow control
When automatic hardware flow control is enabled, the SC16C750B monitors the CTS
pin for a remote buffer overflow indication and controls the RTS pin for local buffer
overflows. Automatic hardware flow control is selected by setting MCR[5] (RTS) and
MCR[1] (CTS) to a logic 1. If CTS transitions from a logic 0 to a logic 1 indicating a
flow control request, the SC16C750B will suspend TX transmissions as soon as the
stop bit of the character in process is shifted out. Transmission is resumed after the
CTS input returns to a logic 0, indicating more data may be sent.
With the Auto-RTS function enabled, an interrupt is generated when the receive FIFO
reaches the programmed trigger level. The RTS pin will not be forced to a logic 1
(RTS off), until the receive FIFO reaches the next trigger level. However, the RTS pin
will return to a logic 0 after the data buffer (FIFO) is emptied. However, under the
above described conditions, the SC16C750B will continue to accept data until the
receive FIFO is full.
6.4 Time-out interrupts
When two interrupt conditions have the same priority, it is important to service these
interrupts correctly. Receive Data Ready and Receive Time Out have the same
interrupt priority (when enabled by IER[0]). The receiver issues an interrupt after the
number of characters have reached the programmed trigger level. In this case, the
SC16C750B FIFO may hold more characters than the programmed trigger level.
Following the removal of a data byte, the user should re-check LSR[0] for additional
characters. A Receive Time Out will not occur if the receive FIFO is empty. The
time-out counter is reset at the center of each stop bit received or each time the
receive holding register (RHR) is read. The actual time-out value is 4 character time.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
11 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
6.5 Programmable baud rate generator
The SC16C750B supports high speed modem technologies that have increased
input data rates by employing data compression schemes. For example, a 33.6 kbit/s
modem that employs data compression may require a 115.2 kbit/s input data rate.
A 128.0 kbit/s ISDN modem that supports data compression may need an input
data rate of 460.8 kbit/s.
X1
1.8432 MHz
C1
22 pF
XTAL2
XTAL1
XTAL2
XTAL1
A single baud rate generator is provided for the transmitter and receiver, allowing
independent TX/RX channel control. The programmable Baud Rate Generator is
capable of accepting an input clock up to 48 MHz, as required for supporting a
3 Mbit/s data rate. The SC16C750B can be configured for internal or external clock
operation. For internal clock oscillator operation, an industry standard microprocessor
crystal (parallel resonant/22-33 pF load) is connected externally between the XTAL1
and XTAL2 pins (see Figure 5). Alternatively, an external clock can be connected to
the XTAL1 pin to clock the internal baud rate generator for standard or custom rates
(see Table 5).
X1
1.8432 MHz
C2
33 pF
C1
22 pF
1.5 kΩ
C2
47 pF
002aaa586
Fig 5. Crystal oscillator connection.
The generator divides the input 16× clock by any divisor from 1 to 216 − 1. The
SC16C750B divides the basic crystal or external clock by 16. The frequency of the
BAUDOUT output pin is exactly 16× (16 times) of the selected baud rate
(BAUDOUT = 16 Baud Rate). Customized baud rates can be achieved by selecting
the proper divisor values for the MSB and LSB sections of baud rate generator.
Programming the Baud Rate Generator registers DLM (MSB) and DLL (LSB)
provides a user capability for selecting the desired final baud rate. The example in
Table 5 shows selectable baud rates when using a 1.8432 MHz crystal.
For custom baud rates, the divisor value can be calculated using the following
equation:
XTAL1 clock frequency
Divisor (in decimal) = ----------------------------------------------------------serial data rate × 16
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
(1)
Rev. 03 — 13 December 2004
12 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 5:
Baud rates using 1.8432 MHz or 3.072 MHz crystal
Using 1.8432 MHz crystal
Desired
baud rate
Divisor for
16× clock
50
Using 3.072 MHz crystal
Baud rate
error
Desired
baud rate
Divisor for
16× clock
2304
50
3840
75
1536
75
2560
110
1047
0.026
110
1745
0.026
134.5
857
0.058
134.5
1428
0.034
150
768
150
1280
300
384
300
640
600
192
600
320
1200
96
1200
160
1800
64
1800
107
2000
58
2000
96
2400
48
2400
80
3600
32
3600
53
4800
24
4800
40
7200
16
7200
27
9600
12
9600
20
19200
6
19200
10
38400
3
38400
5
56000
2
0.69
Baud rate
error
0.312
0.628
1.23
2.86
6.6 DMA operation
The SC16C750B FIFO trigger level provides additional flexibility to the user for block
mode operation. The user can optionally operate the transmit and receive FIFOs in
the DMA mode (FCR[3]). The DMA mode affects the state of the RXRDY and TXRDY
output pins. Tables 6 and 7 show this.
Table 6:
Effect of DMA mode on state of RXRDY pin
Non-DMA mode
DMA mode
1 = FIFO empty
0-to-1 transition when FIFO empties
0 = at least 1 byte in FIFO
1-to-0 transition when FIFO reaches trigger level,
or time-out occurs
Table 7:
Effect of DMA mode on state of TXRDY pin
Non-DMA mode
DMA mode
1 = at least 1 byte in FIFO
0-to-1 transition when FIFO becomes full
0 = FIFO empty
1-to-0 transition when FIFO becomes empty
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
13 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
6.7 Sleep mode
The SC16C750B is designed to operate with low power consumption. A special sleep
mode is included to further reduce power consumption when the chip is not being
used. With IER[4] enabled (set to a logic 1), the SC16C750B enters the sleep mode,
but resumes normal operation when a start bit is detected, a change of state of RX or
on any of the modem input pins RI, CTS, DSR, DCD, or a transmit data is provided by
the user. If the sleep mode is enabled and the SC16C750B is awakened by one of the
conditions described above, it will return to the sleep mode automatically after the last
character is transmitted or read by the user. In any case, the sleep mode will not be
entered while an interrupt(s) is pending. The SC16C750B will stay in the sleep mode
of operation until it is disabled by setting IER[4] to a logic 0.
6.8 Loop-back mode
The internal loop-back capability allows on-board diagnostics. In the loop-back mode,
the normal modem interface pins are disconnected and reconfigured for loop-back
internally. MCR[0:3] register bits are used for controlling loop-back diagnostic testing.
In the loop-back mode, OUT1 and OUT2 in the MCR register (bits 2-3) control the
modem RI and DCD inputs, respectively. MCR signals DTR and RTS (bits 0-1) are
used to control the modem DSR and CTS inputs, respectively. The transmitter output
(TX) and the receiver input (RX) are disconnected from their associated interface
pins, and instead are connected together internally (see Figure 6). The CTS, DSR,
DCD, and RI are disconnected from their normal modem control input pins, and
instead are connected internally to RTS, DTR, OUT2 and OUT1. Loop-back test data
is entered into the transmit holding register via the user data bus interface, D0-D7.
The transmit UART serializes the data and passes the serial data to the receive
UART via the internal loop-back connection. The receive UART converts the serial
data back into parallel data that is then made available at the user data interface
D0-D7. The user optionally compares the received data to the initial transmitted data
for verifying error-free operation of the UART TX/RX circuits.
In this mode, the receiver and transmitter interrupts are fully operational. The Modem
Control Interrupts are also operational. However, the interrupts can only be read
using lower four bits of the Modem Status Register (MSR[0:3]) instead of the four
Modem Status Register bits 4-7. The interrupts are still controlled by the IER.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
14 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
SC16C750B
TRANSMIT
FIFO
REGISTERS
TX
DATA BUS
AND
CONTROL LOGIC
MCR[4] = 1
D0–D7
IOR, IOR
IOW, IOW
RESET
TRANSMIT
SHIFT
REGISTER
A0–A2
CS0, CS1
CS2
AS
REGISTER
SELECT
LOGIC
INTERCONNECT BUS LINES
AND
CONTROL SIGNALS
FLOW
CONTROL
LOGIC
RECEIVE
FIFO
REGISTERS
RECEIVE
SHIFT
REGISTER
RX
FLOW
CONTROL
LOGIC
RTS
DDIS
CTS
DTR
MODEM
CONTROL
LOGIC
DSR
OUT1
INT
TXRDY
RXRDY
INTERRUPT
CONTROL
LOGIC
RI
CLOCK AND
BAUD RATE
GENERATOR
OUT2
DCD
002aaa591
XTAL1
RCLK
XTAL2
BAUDOUT
Fig 6. Internal loop-back mode diagram.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
15 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
7. Register descriptions
Table 8 details the assigned bit functions for the fifteen SC16C750B internal registers.
The assigned bit functions are more fully defined in Section 7.1 through Section 7.10.
Table 8:
SC16C750B internal registers
A2 A1 A0 Register Default[1] Bit 7
General Register
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Set[2]
0
0
0
RHR
XX
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
0
0
THR
XX
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
0
1
IER
00
0
0
low
power
mode
Sleep
mode
modem
status
interrupt
receive
line
status
interrupt
transmit
holding
register
receive
holding
register
0
1
0
FCR
00
RCVR
trigger
(MSB)
RCVR
trigger
(LSB)
64-byte
FIFO
enable
reserved
DMA
mode
select
XMIT
FIFO
reset
RCVR
FIFO
reset
FIFO
enable
0
1
0
ISR
01
FIFOs
enabled
FIFOs
enabled
64-byte
FIFO
enable
0
INT
priority
bit 2
INT
priority
bit 1
INT
priority
bit 0
INT
status
0
1
1
LCR
00
divisor
latch
enable
set break set parity even
parity
parity
enable
stop bits
word
length
bit 1
word
length
bit 0
1
0
0
MCR
00
0
0
flow
control
enable
loop back OUT2,
INT
enable
OUT1
RTS
DTR
1
0
1
LSR
60
FIFO
data
error
trans.
empty
trans.
holding
empty
break
interrupt
framing
error
parity
error
overrun
error
receive
data
ready
1
1
0
MSR
X0
DCD
RI
DSR
CTS
∆DCD
∆RI
∆DSR
∆CTS
1
1
1
SPR
FF
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Special Register
Set[3]
0
0
0
DLL
XX
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
0
1
DLM
XX
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
[1]
[2]
[3]
The value shown represents the register’s initialized HEX value; X = n/a.
These registers are accessible only when LCR[7] = 0.
The Special Register set is accessible only when LCR[7] is set to a logic 1.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
16 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
7.1 Transmit (THR) and Receive (RHR) Holding Registers
The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and
Transmit Shift Register (TSR). The status of the THR is provided in the Line Status
Register (LSR). Writing to the THR transfers the contents of the data bus (D7-D0) to
the THR, providing that the THR or TSR is empty. The THR empty flag in the LSR
register will be set to a logic 1 when the transmitter is empty or when data is
transferred to the TSR. Note that a write operation can be performed when the THR
empty flag is set (logic 0 = FIFO full; logic 1 = at least one FIFO location available).
The serial receive section also contains an 8-bit Receive Holding Register (RHR).
Receive data is removed from the SC16C750B and receive FIFO by reading the RHR
register. The receive section provides a mechanism to prevent false starts. On the
falling edge of a start or false start bit, an internal receiver counter starts counting
clocks at the 16× clock rate. After 7-1⁄2 clocks, the start bit time should be shifted to
the center of the start bit. At this time the start bit is sampled, and if it is still a logic 0
it is validated. Evaluating the start bit in this manner prevents the receiver from
assembling a false character. Receiver status codes will be posted in the LSR.
7.2 Interrupt Enable Register (IER)
The Interrupt Enable Register (IER) masks the interrupts from receiver ready,
transmitter empty, line status and modem status registers. These interrupts would
normally be seen on the INT output pin.
Table 9:
Interrupt Enable Register bits description
Bit
Symbol
Description
7:6
IER[7],
IER[6]
Not used.
5
IER[5]
Low power mode.
Logic 0 = Disable low power mode (normal default condition).
Logic 1 = Enable low power mode.
4
IER[4]
Sleep mode.
Logic 0 = Disable sleep mode (normal default condition).
Logic 1 = Enable sleep mode. See Section 6.7 “Sleep mode” for details.
3
IER[3]
Modem Status Interrupt.
Logic 0 = Disable the modem status register interrupt (normal default
condition).
Logic 1 = Enable the modem status register interrupt.
2
IER[2]
Receive Line Status interrupt. This interrupt will be issued whenever a fully
assembled receive character is transferred from RSR to the RHR/FIFO,
i.e., data ready, LSR[0].
Logic 0 = Disable the receiver line status interrupt (normal default
condition).
Logic 1 = Enable the receiver line status interrupt.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
17 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 9:
Interrupt Enable Register bits description…continued
Bit
Symbol
Description
1
IER[1]
Transmit Holding Register interrupt. This interrupt will be issued whenever
the THR is empty, and is associated with LSR[1].
Logic 0 = Disable the transmitter empty interrupt (normal default
condition).
Logic 1 = Enable the transmitter empty interrupt.
0
IER[0]
Receive Holding Register interrupt. This interrupt will be issued when the
FIFO has reached the programmed trigger level, or is cleared when the
FIFO drops below the trigger level in the FIFO mode of operation.
Logic 0 = Disable the receiver ready interrupt (normal default condition).
Logic 1 = Enable the receiver ready interrupt.
7.2.1
IER versus Receive FIFO interrupt mode operation
When the receive FIFO (FCR[0] = logic 1), and receive interrupts (IER[0] = logic 1)
are enabled, the receive interrupts and register status will reflect the following:
• The receive data available interrupts are issued to the external CPU when the
FIFO has reached the programmed trigger level. It will be cleared when the FIFO
drops below the programmed trigger level.
• FIFO status will also be reflected in the user accessible ISR register when the
FIFO trigger level is reached. Both the ISR register status bit and the interrupt will
be cleared when the FIFO drops below the trigger level.
• The data ready bit (LSR[0]) is set as soon as a character is transferred from the
shift register to the receive FIFO. It is reset when the FIFO is empty.
7.2.2
IER versus Receive/Transmit FIFO polled mode operation
When FCR[0] = logic 1, resetting IER[0:3] enables the SC16C750B in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the
LSR, either or both can be used in the polled mode by selecting respective transmit or
receive control bit(s).
•
•
•
•
LSR[0] will be a logic 1 as long as there is one byte in the receive FIFO.
LSR[1:4] will provide the type of errors encountered, if any.
LSR[5] will indicate when the transmit FIFO is empty.
LSR[6] will indicate when both the transmit FIFO and transmit shift register are
empty.
• LSR[7] will indicate any FIFO data errors.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
18 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO
trigger levels, and select the DMA mode.
7.3.1
DMA mode
Mode 0 (FCR bit 3 = 0): Set and enable the interrupt for each single transmit or
receive operation, and is similar to the 16C450 mode. Transmit Ready (TXRDY) will
go to a logic 0 whenever an empty transmit space is available in the Transmit Holding
Register (THR). Receive Ready (RXRDY) will go to a logic 0 whenever the Receive
Holding Register (RHR) is loaded with a character.
Mode 1 (FCR bit 3 = 1): Set and enable the interrupt in a block mode operation. The
transmit interrupt is set when the transmit FIFO is below the programmed trigger
level. The receive interrupt is set when the receive FIFO fills to the programmed
trigger level. However, the FIFO continues to fill regardless of the programmed level
until the FIFO is full. RXRDY remains a logic 0 as long as the FIFO fill level is above
the programmed trigger level.
7.3.2
FIFO mode
Table 10:
FIFO Control Register bits description
Bit
Symbol
Description
7:6
FCR[7]
(MSB),
FCR[6]
(LSB)
RCVR trigger. These bits are used to set the trigger level for the receive
FIFO interrupt.
FCR[5]
Logic 0 = 16-byte mode (normal default condition).
5
An interrupt is generated when the number of characters in the FIFO
equals the programmed trigger level. However, the FIFO will continue to
be loaded until it is full. Refer to Table 11.
Logic 1 = 64-byte mode.
4
FCR[4]
Reserved.
3
FCR[3]
DMA mode select.
Logic 0 = Set DMA mode ‘0’ (normal default condition).
Logic 1 = Set DMA mode ‘1’
Transmit operation in mode ‘0’: When the SC16C750B is in the
16C450 mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode
(FIFOs enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there are
no characters in the transmit FIFO or transmit holding register, the
TXRDY pin will be a logic 0. Once active, the TXRDY pin will go to a
logic 1 after the first character is loaded into the transmit holding
register.
Receive operation in mode ‘0’: When the SC16C750B is in 16C450
mode, or in the FIFO mode (FCR[0] = logic 1; FCR[3] = logic 0) and
there is at least one character in the receive FIFO, the RXRDY pin will
be a logic 0. Once active, the RXRDY pin will go to a logic 1 when there
are no more characters in the receiver.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
19 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 10:
Bit
FIFO Control Register bits description…continued
Symbol
Description
Transmit operation in mode ‘1’: When the SC16C750B is in FIFO
mode (FCR[0] = logic 1; FCR[3] = logic 1), the TXRDY pin will be a
logic 1 when the transmit FIFO is completely full. It will be a logic 0 when
the FIFO is emptied.
Receive operation in mode ‘1’: When the SC16C750B is in FIFO
mode (FCR[0] = logic 1; FCR[3] = logic 1) and the trigger level has been
reached, or a Receive Time-Out has occurred, the RXRDY pin will go to
a logic 0. Once activated, it will go to a logic 1 after there are no more
characters in the FIFO.
2
FCR[2]
XMIT FIFO reset.
Logic 0 = No FIFO transmit reset (normal default condition).
Logic 1 = Clears the contents of the transmit FIFO and resets the
FIFO counter logic (the transmit shift register is not cleared or
altered). This bit will return to a logic 0 after clearing the FIFO.
1
FCR[1]
RCVR FIFO reset.
Logic 0 = No FIFO receive reset (normal default condition).
Logic 1 = Clears the contents of the receive FIFO and resets the FIFO
counter logic (the receive shift register is not cleared or altered). This
bit will return to a logic 0 after clearing the FIFO.
0
FCR[0]
FIFO enable.
Logic 0 = Disable the transmit and receive FIFO (normal default
condition).
Logic 1 = Enable the transmit and receive FIFO.
Table 11:
RCVR trigger levels
FCR[7]
FCR[6]
RX FIFO trigger level (bytes)
16-byte operation
64-byte operation
0
0
1
1
0
1
4
16
1
0
8
32
1
1
14
56
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
20 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
7.4 Interrupt Status Register (ISR)
The SC16C750B provides four levels of prioritized interrupts to minimize external
software interaction. The Interrupt Status Register (ISR) provides the user with four
interrupt status bits. Performing a read cycle on the ISR will provide the user with the
highest pending interrupt level to be serviced. No other interrupts are acknowledged
until the pending interrupt is serviced. Whenever the interrupt status register is read,
the interrupt status is cleared. However, it should be noted that only the current
pending interrupt is cleared by the read. A lower level interrupt may be seen after
re-reading the interrupt status bits. Table 12 “Interrupt source” shows the data values
(bits 0-4) for the four prioritized interrupt levels and the interrupt sources associated
with each of these interrupt levels.
Table 12:
Interrupt source
Priority
level
ISR[3]
ISR[2]
ISR[1]
ISR[0]
Source of the interrupt
1
0
1
1
0
LSR (Receiver Line Status Register)
2
0
1
0
0
RXRDY (Received Data Ready)
2
1
1
0
0
RXRDY (Receive Data time-out)
3
0
0
1
0
TXRDY (Transmitter Holding Register
Empty)
4
0
0
0
0
MSR (Modem Status Register)
Table 13:
Interrupt Status Register bits description
Bit
Symbol
Description
7:6
ISR[7:6]
FIFOs enabled. These bits are set to a logic 0 when the FIFO is
not being used. They are set to a logic 1 when the FIFOs are
enabled.
5
ISR[5]
64-byte FIFO enable.
Logic 0 or cleared = default condition.
Logic 0 = 16-byte operation.
Logic 1 = 64-byte operation.
4
ISR[4]
Not used.
3:1
ISR[3:1]
INT priority bits 2-0. These bits indicate the source for a pending
interrupt at interrupt priority levels 1, 2, and 3 (see Table 12).
0
ISR[0]
INT status.
Logic 0 or cleared = default condition.
Logic 0 = An interrupt is pending and the ISR contents may be
used as a pointer to the appropriate interrupt service routine.
Logic 1 = No interrupt pending (normal default condition).
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
21 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
7.5 Line Control Register (LCR)
The Line Control Register is used to specify the asynchronous data communication
format. The word length, the number of stop bits, and the parity are selected by
writing the appropriate bits in this register.
Table 14:
Line Control Register bits description
Bit
Symbol
Description
7
LCR[7]
Divisor latch enable. The internal baud rate counter latch and Enhance
Feature mode enable.
Logic 0 = Divisor latch disabled (normal default condition).
Logic 1 = Divisor latch and enhanced feature register enabled.
6
LCR[6]
Set break. When enabled, the Break control bit causes a break condition
to be transmitted (the TX output is forced to a logic 0 state). This
condition exists until disabled by setting LCR[6] to a logic 0.
Logic 0 = no TX break condition (normal default condition).
Logic 1 = forces the transmitter output (TX) to a logic 0 for alerting the
remote receiver to a line break condition.
5
LCR[5]
Set parity. If the parity bit is enabled, LCR[5] selects the forced parity
format. Programs the parity conditions (see Table 15).
Logic 0 = parity is not forced (normal default condition).
LCR[5] = logic 1 and LCR[4] = logic 0: parity bit is forced to a logical 1
for the transmit and receive data.
LCR[5] = logic 1 and LCR[4] = logic 1: parity bit is forced to a logical 0
for the transmit and receive data.
4
LCR[4]
Even parity. If the parity bit is enabled with LCR[3] set to a logic 1,
LCR[4] selects the even or odd parity format.
Logic 0 = ODD Parity is generated by forcing an odd number of
logic 1s in the transmitted data. The receiver must be programmed to
check the same format (normal default condition).
Logic 1 = EVEN Parity is generated by forcing an even number of
logic 1s in the transmitted data. The receiver must be programmed to
check the same format.
3
LCR[3]
Parity enable. Parity or no parity can be selected via this bit.
Logic 0 = no parity (normal default condition).
Logic 1 = a parity bit is generated during the transmission, receiver
checks the data and parity for transmission errors.
2
LCR[2]
Stop bits. The length of stop bit is specified by this bit in conjunction with
the programmed word length (see Table 16).
Logic 0 or cleared = default condition.
1:0
LCR[1:0]
Word length bits 1, 0. These two bits specify the word length to be
transmitted or received (see Table 17).
Logic 0 or cleared = default condition.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
22 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 15:
LCR[5] parity selection
LCR[5]
LCR[4]
LCR[3]
Parity selection
X
X
0
no parity
0
0
1
ODD parity
0
1
1
EVEN parity
1
0
1
force parity ‘1’
1
1
1
forced parity ‘0’
Table 16:
LCR[2] stop bit length
LCR[2]
Word length
0
5, 6, 7, 8
1
1
5
1-1⁄2
1
6, 7, 8
2
Table 17:
Stop bit length (bit times)
LCR[1:0] word length
LCR[1]
LCR[0]
Word length
0
0
5
0
1
6
1
0
7
1
1
8
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
23 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
Table 18:
Modem Control Register bits description
Bit
Symbol
Description
7
MCR[7]
Reserved. Set to 0.
6
MCR[6]
Reserved. Set to 0.
5
MCR[5]
AFE. This bit is the auto flow control enable. When this bit is set, the
auto flow control is enabled.
4
MCR[4]
Loop-back. Enable the local loop-back mode (diagnostics). In this
mode the transmitter output (TX) and the receiver input (RX), CTS,
DSR, DCD, and RI are disconnected from the SC16C750B I/O pins.
Internally the modem data and control pins are connected into a
loop-back data configuration (see Figure 6). In this mode, the receiver
and transmitter interrupts remain fully operational. The Modem
Control Interrupts are also operational, but the interrupts’ sources are
switched to the lower four bits of the Modem Control. Interrupts
continue to be controlled by the IER register.
Logic 0 = Disable loop-back mode (normal default condition).
Logic 1 = Enable local loop-back mode (diagnostics).
3
MCR[3]
OUT2, INTx enable. Used to control the modem DCD signal in the
loop-back mode.
Logic 0 = Forces INT output to the 3-State mode. In the loop-back
mode, sets OUT2 (DCD) internally to a logic 1.
Logic 1 = Forces the INT output to the active mode. In the
loop-back mode, sets OUT2 (DCD) internally to a logic 0.
2
MCR[2]
OUT1. This bit is used in the Loop-back mode only. In the loop-back
mode, this bit is used to write the state of the modem RI interface
signal via OUT1.
1
MCR[1]
RTS
Logic 0 = Force RTS output to a logic 1 (normal default condition).
Logic 1 = Force RTS output to a logic 0.
0
MCR[0]
DTR
Logic 0 = Force DTR output to a logic 1 (normal default condition).
Logic 1 = Force DTR output to a logic 0.
The flow control can be configured by programming MCR[1] and MCR[5] as shown in
Table 19.
Table 19:
Flow control configuration
MCR[5] (AFE)
MCR[1] (RTS)
Flow configuration
1
1
auto RTS and CTS enabled
1
0
auto CTS only enabled
0
X
auto RTS and CTS disabled
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
24 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
7.7 Line Status Register (LSR)
This register provides the status of data transfers between the SC16C750B and
the CPU.
Table 20:
Line Status Register bits description
Bit
Symbol
Description
7
LSR[7]
FIFO data error.
Logic 0 = No error (normal default condition).
Logic 1 = At least one parity error, framing error or break indication is in
the current FIFO data. This bit is cleared when LSR register is read.
6
LSR[6]
THR and TSR empty. This bit is the Transmit Empty indicator. This bit is
set to a logic 1 whenever the transmit holding register and the transmit
shift register are both empty. It is reset to logic 0 whenever either the THR
or TSR contains a data character. In the FIFO mode, this bit is set to ‘1’
whenever the transmit FIFO and transmit shift register are both empty.
5
LSR[5]
THR empty. This bit is the Transmit Holding Register Empty indicator.
This bit indicates that the UART is ready to accept a new character for
transmission. In addition, this bit causes the UART to issue an interrupt to
CPU when the THR interrupt enable is set. The THR bit is set to a logic 1
when a character is transferred from the transmit holding register into the
transmitter shift register. The bit is reset to a logic 0 concurrently with the
loading of the transmitter holding register by the CPU. In the FIFO mode,
this bit is set when the transmit FIFO is empty; it is cleared when at least
1 byte is written to the transmit FIFO.
4
LSR[4]
Break interrupt.
Logic 0 = No break condition (normal default condition).
Logic 1 = The receiver received a break signal (RX was a logic 0 for
one character frame time). In the FIFO mode, only one break character
is loaded into the FIFO.
3
LSR[3]
Framing error.
Logic 0 = No framing error (normal default condition).
Logic 1 = Framing error. The receive character did not have a valid stop
bit(s). In the FIFO mode, this error is associated with the character at
the top of the FIFO.
2
LSR[2]
Parity error.
Logic 0 = No parity error (normal default condition).
Logic 1 = Parity error. The receive character does not have correct
parity information and is suspect. In the FIFO mode, this error is
associated with the character at the top of the FIFO.
1
LSR[1]
Overrun error.
Logic 0 = No overrun error (normal default condition).
Logic 1 = Overrun error. A data overrun error occurred in the receive
shift register. This happens when additional data arrives while the FIFO
is full. In this case, the previous data in the shift register is overwritten.
Note that under this condition, the data byte in the receive shift register
is not transferred into the FIFO, therefore the data in the FIFO is not
corrupted by the error.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
25 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 20:
Line Status Register bits description…continued
Bit
Symbol
Description
0
LSR[0]
Receive data ready.
Logic 0 = No data in receive holding register or FIFO (normal default
condition).
Logic 1 = Data has been received and is saved in the receive holding
register or FIFO.
7.8 Modem Status Register (MSR)
This register provides the current state of the control interface signals from the
modem, or other peripheral device to which the SC16C750B is connected. Four bits
of this register are used to indicate the changed information. These bits are set to a
logic 1 whenever a control input from the modem changes state. These bits are set to
a logic 0 whenever the CPU reads this register.
Table 21:
Modem Status Register bits description
Bit
Symbol
Description
7
MSR[7]
Data Carrier Detect. DCD (Active-HIGH, logical 1). Normally this bit is
the complement of the DCD input. In the loop-back mode this bit is
equivalent to the OUT2 bit in the MCR register.
6
MSR[6]
Ring Indicator. RI (Active-HIGH, logical 1). Normally this bit is the
complement of the RI input. In the loop-back mode this bit is equivalent
to the OUT1 bit in the MCR register.
5
MSR[5]
Data Set Ready. DSR (Active-HIGH, logical 1). Normally this bit is the
complement of the DSR input. In loop-back mode this bit is equivalent to
the DTR bit in the MCR register.
4
MSR[4]
Clear To Send. CTS. CTS functions as hardware flow control signal input
if it is enabled via EFR[7]. Flow control (when enabled) allows starting
and stopping the transmissions based on the external modem CTS
signal. A logic 1 at the CTS pin will stop SC16C750B transmissions as
soon as current character has finished transmission. Normally MSR[4] is
the complement of the CTS input. However, in the loop-back mode, this
bit is equivalent to the RTS bit in the MCR register.
3
MSR[3]
∆DCD [1]
Logic 0 = No DCD change (normal default condition).
Logic 1 = The DCD input to the SC16C750B has changed state since
the last time it was read. A modem Status Interrupt will be generated.
2
MSR[2]
∆RI [1]
Logic 0 = No RI change (normal default condition).
Logic 1 = The RI input to the SC16C750B has changed from a logic 0
to a logic 1. A modem Status Interrupt will be generated.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
26 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 21:
Modem Status Register bits description…continued
Bit
Symbol
Description
1
MSR[1]
∆DSR [1]
Logic 0 = No DSR change (normal default condition).
Logic 1 = The DSR input to the SC16C750B has changed state since
the last time it was read. A modem Status Interrupt will be generated.
0
MSR[0]
∆CTS [1]
Logic 0 = No CTS change (normal default condition).
Logic 1 = The CTS input to the SC16C750B has changed state since
the last time it was read. A modem Status Interrupt will be generated.
[1]
Whenever any MSR[0:3] is set to logic 1, a Modem Status Interrupt will be generated.
7.9 Scratchpad Register (SPR)
The SC16C750B provides a temporary data register to store 8 bits of user
information.
7.10 SC16C750B external reset conditions
Table 22:
Reset state for registers
Register
Reset state
IER
IER[7:0] = 0
ISR
ISR[7:1] = 0; ISR[0] = 1
LCR
LCR[7:0] = 0
MCR
MCR[7:0] = 0
LSR
LSR[7] = 0; LSR[6:5] = 1; LSR[4:0] = 0
MSR
MSR[7:4] = input signals; MSR[3:0] = 0
FCR
FCR[7:0] = 0
EFR
EFR[7:0] = 0
Table 23:
Reset state for outputs
Output
Reset state
TX
HIGH
RTS
HIGH
DTR
HIGH
RXRDY
HIGH (STD mode)
TXRDY
LOW (STD mode)
INT
LOW (STD mode)
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
27 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
8. Limiting values
Table 24: Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
VCC
supply voltage
Vn
Tamb
Conditions
Min
Max
Unit
-
7
V
voltage at any pin
GND − 0.3
VCC + 0.3
V
operating temperature
−40
+85
°C
Tstg
storage temperature
−65
+150
°C
Ptot(pack)
total power dissipation per package
-
500
mW
9. Static characteristics
Table 25: DC electrical characteristics
Tamb = −40 °C to +85 °C; VCC = 2.5V, 3.3 V or 5.0 V ±10%, unless otherwise specified.
Symbol
Parameter
Conditions
2.5 V
3.3 V
5.0 V
Min
Max
Min
Max
Min
Max
Unit
VIL(CK)
LOW-level clock input voltage
−0.3
0.45
−0.3
0.6
−0.5
0.6
V
VIH(CK)
HIGH-level clock input voltage
1.8
VCC
2.4
VCC
3.0
VCC
V
VIL
LOW-level input voltage
−0.3
0.65
−0.3
0.8
−0.5
0.8
V
VIH
HIGH-level input voltage
1.6
-
2.0
-
2.2
VCC
V
VOL
LOW-level output voltage on all
outputs[1]
IOL = 5 mA
(databus)
-
-
-
-
-
0.4
V
IOL = 4 mA
(other outputs)
-
-
-
0.4
-
-
V
IOL = 2 mA
(databus)
-
0.4
-
-
-
-
V
IOL = 1.6 mA
(other outputs)
-
0.4
-
-
-
-
V
IOH = −5 mA
(databus)
-
-
-
-
2.4
-
V
IOH = −1 mA
(other outputs)
-
-
2.0
-
-
-
V
IOH = −800 µA
(databus)
1.85
-
-
-
-
-
V
IOH = −400 µA
(other outputs)
1.85
-
-
-
-
-
V
VOH
HIGH-level output voltage
ILIL
LOW-level input leakage current
-
±10
-
±10
-
±10
µA
ICL
clock leakage
-
±30
-
±30
-
±30
µA
ICC
average power supply current
-
3.5
-
4.5
-
4.5
mA
Ci
input capacitance
-
5
-
5
-
5
pF
Rpu(int)
internal pull-up resistance[2]
500
-
500
-
500
-
kΩ
[1]
[2]
Except for x2, VOL = 1 V typically.
Refer to Table 2 “Pin description” on page 5 for a listing of pins having internal pull-up resistors.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
28 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
10. Dynamic characteristics
Table 26: AC electrical characteristics
Tamb = −40 °C to +85 °C; VCC = 2.5 V, 3.3 V or 5 V ±10%, unless otherwise specified.
Symbol
Parameter
Conditions
2.5 V
3.3 V
5.0 V
Unit
Min
Max
Min
Max
Min
Max
15
-
13
-
10
-
ns
-
16
-
32
-
48
MHz
t1w, t2w
clock pulse duration
t3w
oscillator/clock frequency
t4w
address strobe width
45
-
35
-
25
-
ns
t5s
address set-up time
5
-
5
-
1
-
ns
t5h
address hold time
5
-
5
-
5
-
ns
t6s
chip select set-up time to AS
10
-
5
-
0
-
ns
t6h
address hold time
0
-
0
-
0
-
ns
10
-
10
-
5
-
ns
t6s'
address set-up time
[1]
[2]
t6h
chip select hold time
0
-
0
-
0
-
ns
t7d
IOR delay from chip select
10
-
10
-
10
-
ns
t7w
IOR strobe width
77
-
26
-
23
-
ns
t7h
chip select hold time from IOR
0
-
0
-
0
-
ns
5
-
5
-
5
-
ns
10
-
10
-
10
-
ns
25 pF load
[2]
t7h'
address hold time
t8d
IOR delay from address
t9d
read cycle delay
25 pF load
20
-
20
-
20
-
ns
t11d
IOR to DDIS delay
25 pF load
-
100
-
35
-
30
ns
t12d
delay from IOR to data
25 pF load
-
77
-
26
-
23
ns
t12h
data disable time
25 pF load
-
15
-
15
-
15
ns
t13d
IOW delay from chip select
10
-
10
-
10
-
ns
t13w
IOW strobe width
20
-
20
-
15
-
ns
t13h
chip select hold time from IOW
0
-
0
-
0
-
ns
t14d
IOW delay from address
10
-
10
-
10
-
ns
t15d
write cycle delay
25
-
25
-
20
-
ns
t16s
data set-up time
20
-
20
-
15
-
ns
t16h
data hold time
15
-
5
-
5
-
ns
t17d
delay from IOW to output
25 pF load
-
100
-
33
-
29
ns
t18d
delay to set interrupt from Modem
input
25 pF load
-
100
-
24
-
23
ns
t19d
delay to reset interrupt from IOR
25 pF load
-
100
-
24
-
23
ns
t20d
delay from stop to set interrupt
-
1
-
1
-
1
Rclk
t21d
delay from IOR to reset interrupt
-
100
-
29
-
28
ns
t22d
delay from start to set interrupt
-
100
-
45
-
40
ns
t23d
delay from IOW to transmit start
8
24
8
24
8
24
Rclk
t24d
delay from IOW to reset interrupt
-
100
-
45
-
40
ns
t25d
delay from stop to set RXRDY
-
1
-
1
-
1
Rclk
t26d
delay from IOR to reset RXRDY
-
100
-
45
-
40
ns
t27d
delay from IOW to set TXRDY
-
100
-
45
-
40
ns
25 pF load
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
29 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Table 26: AC electrical characteristics…continued
Tamb = −40 °C to +85 °C; VCC = 2.5 V, 3.3 V or 5 V ±10%, unless otherwise specified.
Symbol
Parameter
Conditions
2.5 V
3.3 V
Unit
Min
Max
Min
Max
Min
Max
8
-
8
Rclk
-
40
-
ns
t28d
delay from start to reset TXRDY
-
8
-
tRESET
Reset pulse width
100
-
40
N
baud rate divisor
1
216 − 1 1
[1]
[2]
5.0 V
216 − 1 1
216 − 1 Rclk
Applies to external clock, crystal oscillator max 24 MHz.
Applicable only when AS is tied LOW.
10.1 Timing diagrams
t4w
AS
t5s
t5h
VALID
ADDRESS
A0–A2
t6s
t6h
CS2
CS1–CS0
VALID
t7d
t7h
t7w
t8d
IOR, IOR
t9d
ACTIVE
t11d
t11d
DDIS
ACTIVE
t12d
D0–D7
t12h
DATA
002aaa331
Fig 7. General read timing when using AS signal.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
30 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
t4w
AS
t5s
t5h
VALID
ADDRESS
A0–A2
t6s
t6h
CS2
CS1–CS0
VALID
t13d
t13h
t13w
t14d
IOW, IOW
t15d
ACTIVE
t16s
D0–D7
t16h
DATA
002aaa332
Fig 8. General write timing when using AS signal.
VALID
ADDRESS
A0–A2
VALID
ADDRESS
t6s′
CS
t7h′
ACTIVE
t9d
ACTIVE
t12h
t12d
D0–D7
t7h′
t7w
ACTIVE
t7w
IOR
t6s′
t12d
t12h
DATA
002aaa333
Fig 9. General read timing when AS is tied to GND.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
31 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
VALID
ADDRESS
A0–A2
VALID
ADDRESS
t6s′
t7h′
t7h′
t6s′
ACTIVE
CS
ACTIVE
t13w
IOW
t15d
t13w
ACTIVE
t16s
D0–D7
t16h
t16s
t16h
DATA
002aaa334
Fig 10. General write timing when AS is tied to GND.
IOW
ACTIVE
t17d
RTS
DTR
CHANGE OF STATE
CHANGE OF STATE
DCD
CHANGE OF STATE
CTS
CHANGE OF STATE
DSR
t18d
INT
t18d
ACTIVE
ACTIVE
ACTIVE
t19d
IOR
ACTIVE
ACTIVE
ACTIVE
t18d
RI
CHANGE OF STATE
002aaa111
Fig 11. Modem input/output timing.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
32 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
t2w
t1w
EXTERNAL
CLOCK
002aaa112
t3w
Fig 12. External clock timing.
start
bit
RX
parity
bit
data bits (0 to 7)
D0
D1
D2
D3
D4
D5
D6
stop
bit
next
data
start
bit
D7
5 data bits
6 data bits
7 data bits
t20d
active
INT
t21d
active
IOR
16 baud rate clock
002aaa113
Fig 13. Receive timing.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
33 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
PARITY
BIT
START
BIT
STOP
BIT
NEXT
DATA
START
BIT
DATA BITS (5–8)
RX
D0
D1
D2
D3
D4
D5
D6
D7
t25d
ACTIVE
DATA
READY
RXRDY
t26d
ACTIVE
IOR
002aaa114
Fig 14. Receive ready timing in non-FIFO mode.
START
BIT
PARITY
BIT
STOP
BIT
DATA BITS (5–8)
RX
D0
D1
D2
D3
D4
D5
D6
D7
FIRST BYTE THAT
REACHES THE
TRIGGER LEVEL
t25d
ACTIVE
DATA
READY
RXRDY
t26d
ACTIVE
IOR
002aaa115
Fig 15. Receive ready timing in FIFO mode.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
34 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
start
bit
TX
parity
bit
data bits (0 to 7)
D0
D1
D2
D3
D4
D5
D6
stop
bit
next
data
start
bit
D7
5 data bits
6 data bits
7 data bits
active
transmitter ready
INT
t22d
t24d
t23d
IOW
active
active
16 baud rate clock
002aaa116
Fig 16. Transmit timing.
START
BIT
PARITY
BIT
STOP
BIT
NEXT
DATA
START
BIT
DATA BITS (5–8)
TX
D0
IOW
ACTIVE
D0–D7
BYTE #1
D1
D2
D3
D4
D5
D6
D7
TRANSMITTER READY
t28d
t27d
ACTIVE
TXRDY
TRANSMITTER
NOT READY
002aaa129
Fig 17. Transmit ready timing in non-FIFO mode.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
35 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
START
BIT
PARITY
BIT
STOP
BIT
DATA BITS (5-8)
TX
D0
D1
D2
D3
D4
D5
D6
D7
5 DATA BITS
6 DATA BITS
7 DATA BITS
IOW
ACTIVE
t28d
D0–D7
BYTE #16
t27d
TXRDY
FIFO FULL
002aaa118
Fig 18. Transmit ready timing in FIFO mode (DMA mode ‘1’).
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
36 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
11. Package outline
PLCC44: plastic leaded chip carrier; 44 leads
SOT187-2
eD
eE
y
X
39
A
29
28
40
bp
ZE
b1
w M
44
1
E
HE
pin 1 index
A
A4 A1
e
(A 3)
6
β
18
Lp
k
7
detail X
17
e
v M A
ZD
D
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm dimensions are derived from the original inch dimensions)
A4
A1
e
UNIT A
A3
D(1) E(1)
eD
eE
HD
bp b1
max.
min.
4.57
4.19
mm
inches
0.81
0.66
HE
k
16.66 16.66
16.00 16.00 17.65 17.65 1.22
1.27
16.51 16.51
14.99 14.99 17.40 17.40 1.07
0.51
0.25
3.05
0.53
0.33
0.180
0.02
0.165
0.01
0.12
0.021 0.032 0.656 0.656
0.05
0.013 0.026 0.650 0.650
0.63
0.59
0.63
0.59
Lp
v
w
y
1.44
1.02
0.18
0.18
0.1
ZD(1) ZE(1)
max. max.
2.16
β
2.16
45 o
0.695 0.695 0.048 0.057
0.007 0.007 0.004 0.085 0.085
0.685 0.685 0.042 0.040
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT187-2
112E10
MS-018
EDR-7319
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
01-11-14
Fig 19. PLCC44 (SOT187-2).
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
37 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
HVQFN32: plastic thermal enhanced very thin quad flat package; no leads;
32 terminals; body 5 x 5 x 0.85 mm
A
B
D
SOT617-1
terminal 1
index area
A
A1
E
c
detail X
C
e1
e
1/2 e
16
y
y1 C
v M C A B
w M C
b
9
L
17
8
e
e2
Eh
1/2 e
1
terminal 1
index area
24
32
25
X
Dh
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A(1)
max.
A1
b
c
D (1)
Dh
E (1)
Eh
e
e1
e2
L
v
w
y
y1
mm
1
0.05
0.00
0.30
0.18
0.2
5.1
4.9
3.25
2.95
5.1
4.9
3.25
2.95
0.5
3.5
3.5
0.5
0.3
0.1
0.05
0.05
0.1
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT617-1
---
MO-220
---
EUROPEAN
PROJECTION
ISSUE DATE
01-08-08
02-10-18
Fig 20. HVQFN32 (SOT617-1).
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
38 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
LQFP64: plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm
SOT314-2
c
y
X
A
48
33
49
32
ZE
e
E HE
A
A2
(A 3)
A1
wM
θ
bp
pin 1 index
64
Lp
L
17
detail X
16
1
ZD
e
v M A
wM
bp
D
B
HD
v M B
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
mm
1.6
0.20
0.05
1.45
1.35
0.25
0.27
0.17
0.18
0.12
10.1
9.9
10.1
9.9
0.5
HD
HE
12.15 12.15
11.85 11.85
L
Lp
v
w
y
1
0.75
0.45
0.2
0.12
0.1
Z D (1) Z E (1)
1.45
1.05
1.45
1.05
θ
7o
o
0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT314-2
136E10
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-01-19
03-02-25
Fig 21. LQFP64 (SOT314-2).
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
39 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
12. Soldering
12.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages (document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended. In these situations
reflow soldering is recommended.
12.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 270 °C depending on solder
paste material. The top-surface temperature of the packages should preferably be
kept:
• below 225 °C (SnPb process) or below 245 °C (Pb-free process)
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness ≥ 2.5 mm
– for packages with a thickness < 2.5 mm and a volume ≥ 350 mm3 so called
thick/large packages.
• below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with
a thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all
times.
12.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
• Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
40 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
• For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
parallel to the transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
• For packages with leads on four sides, the footprint must be placed at a 45° angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 °C or
265 °C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in
most applications.
12.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time
must be limited to 10 seconds at up to 300 °C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320 °C.
12.5 Package related soldering information
Table 27:
Suitability of surface mount IC packages for wave and reflow soldering
methods
Package[1]
Soldering method
BGA, HTSSON..T[3], LBGA, LFBGA, SQFP,
SSOP..T[3], TFBGA, USON, VFBGA
Reflow[2]
not suitable
suitable
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP, not suitable[4]
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
suitable
PLCC[5], SO, SOJ
suitable
suitable
LQFP, QFP, TQFP
not recommended[5][6]
suitable
recommended[7]
SSOP, TSSOP, VSO, VSSOP
not
CWQCCN..L[8],
not suitable
[1]
[2]
PMFP[9],
WQCCN..L[8]
suitable
not suitable
For more detailed information on the BGA packages refer to the (LF)BGA Application Note
(AN01026); order a copy from your Philips Semiconductors sales office.
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal
or external package cracks may occur due to vaporization of the moisture in them (the so called
popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated
Circuit Packages; Section: Packing Methods.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Wave
Rev. 03 — 13 December 2004
41 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
[3]
These transparent plastic packages are extremely sensitive to reflow soldering conditions and must
on no account be processed through more than one soldering cycle or subjected to infrared reflow
soldering with peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow
oven. The package body peak temperature must be kept as low as possible.
These packages are not suitable for wave soldering. On versions with the heatsink on the bottom
side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with
the heatsink on the top side, the solder might be deposited on the heatsink surface.
If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it
is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
Wave soldering is suitable for SSOP, TSSOP, VSO and VSOP packages with a pitch (e) equal to or
larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than
0.5 mm.
Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered
pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex
foil by using a hot bar soldering process. The appropriate soldering profile can be provided on
request.
Hot bar soldering or manual soldering is suitable for PMFP packages.
[4]
[5]
[6]
[7]
[8]
[9]
13. Revision history
Table 28:
Revision history
Rev Date
03
20041213
CPCN
Description
-
Product data (9397 750 14453)
Modifications:
•
There is no modification to the data sheet. However, reader is advised to refer to
AN10333 (Rev. 02) “SC16CXXXB baud rate deviation tolerance” (9397 750 14411)
that was released together with this revision.
02
20040527
-
Product data (9397 750 13318)
01
20040329
-
Product data (9397 750 11969)
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Product data
Rev. 03 — 13 December 2004
42 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
14. Data sheet status
Level
Data sheet status[1]
Product status[2][3]
Definition
I
Objective data
Development
This data sheet contains data from the objective specification for product development. Philips
Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data
Qualification
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data
Production
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
[1]
Please consult the most recently issued data sheet before initiating or completing a design.
[2]
The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at
URL http://www.semiconductors.philips.com.
[3]
For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
15. Definitions
16. Disclaimers
Short-form specification — The data in a short-form specification is
extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Life support — These products are not designed for use in life support
appliances, devices, or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors
customers using or selling these products for use in such applications do so
at their own risk and agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Limiting values definition — Limiting values given are in accordance with
the Absolute Maximum Rating System (IEC 60134). Stress above one or
more of the limiting values may cause permanent damage to the device.
These are stress ratings only and operation of the device at these or at any
other conditions above those given in the Characteristics sections of the
specification is not implied. Exposure to limiting values for extended periods
may affect device reliability.
Application information — Applications that are described herein for any
of these products are for illustrative purposes only. Philips Semiconductors
make no representation or warranty that such applications will be suitable for
the specified use without further testing or modification.
Right to make changes — Philips Semiconductors reserves the right to
make changes in the products - including circuits, standard cells, and/or
software - described or contained herein in order to improve design and/or
performance. When the product is in full production (status ‘Production’),
relevant changes will be communicated via a Customer Product/Process
Change Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no
licence or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are
free from patent, copyright, or mask work right infringement, unless otherwise
specified.
Contact information
For additional information, please visit http://www.semiconductors.philips.com.
For sales office addresses, send e-mail to: [email protected].
Product data
Fax: +31 40 27 24825
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9397 750 14453
Rev. 03 — 13 December 2004
43 of 44
SC16C750B
Philips Semiconductors
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
Contents
1
2
3
4
5
5.1
5.2
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
7
7.1
7.2
7.2.1
7.2.2
7.3
7.3.1
7.3.2
7.4
7.5
7.6
7.7
7.8
7.9
7.10
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pinning information . . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
Functional description . . . . . . . . . . . . . . . . . . . 9
Internal registers. . . . . . . . . . . . . . . . . . . . . . . . 9
FIFO operation . . . . . . . . . . . . . . . . . . . . . . . . 10
Hardware flow control . . . . . . . . . . . . . . . . . . . 11
Time-out interrupts . . . . . . . . . . . . . . . . . . . . . 11
Programmable baud rate generator . . . . . . . . 12
DMA operation . . . . . . . . . . . . . . . . . . . . . . . . 13
Sleep mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Loop-back mode . . . . . . . . . . . . . . . . . . . . . . . 14
Register descriptions . . . . . . . . . . . . . . . . . . . 16
Transmit (THR) and Receive (RHR)
Holding Registers . . . . . . . . . . . . . . . . . . . . . 17
Interrupt Enable Register (IER) . . . . . . . . . . . 17
IER versus Receive FIFO interrupt
mode operation . . . . . . . . . . . . . . . . . . . . . . . 18
IER versus Receive/Transmit FIFO polled
mode operation . . . . . . . . . . . . . . . . . . . . . . . 18
FIFO Control Register (FCR) . . . . . . . . . . . . . 19
DMA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FIFO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Interrupt Status Register (ISR) . . . . . . . . . . . . 21
Line Control Register (LCR) . . . . . . . . . . . . . . 22
Modem Control Register (MCR) . . . . . . . . . . . 24
Line Status Register (LSR) . . . . . . . . . . . . . . . 25
Modem Status Register (MSR). . . . . . . . . . . . 26
Scratchpad Register (SPR) . . . . . . . . . . . . . . 27
SC16C750B external reset conditions . . . . . . 27
© Koninklijke Philips Electronics N.V. 2004.
Printed in the U.S.A.
All rights are reserved. Reproduction in whole or in part is prohibited without the prior
written consent of the copyright owner.
The information presented in this document does not form part of any quotation or
contract, is believed to be accurate and reliable and may be changed without notice. No
liability will be accepted by the publisher for any consequence of its use. Publication
thereof does not convey nor imply any license under patent- or other industrial or
intellectual property rights.
Date of release: 13 December 2004
Document order number: 9397 750 14453
8
9
10
10.1
11
12
12.1
12.2
12.3
12.4
12.5
13
14
15
16
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .
Static characteristics . . . . . . . . . . . . . . . . . . .
Dynamic characteristics . . . . . . . . . . . . . . . . .
Timing diagrams. . . . . . . . . . . . . . . . . . . . . . .
Package outline . . . . . . . . . . . . . . . . . . . . . . . .
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction to soldering surface mount
packages . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reflow soldering. . . . . . . . . . . . . . . . . . . . . . .
Wave soldering. . . . . . . . . . . . . . . . . . . . . . . .
Manual soldering . . . . . . . . . . . . . . . . . . . . . .
Package related soldering information . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . .
Data sheet status. . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
28
29
30
37
40
40
40
40
41
41
42
43
43
43