Philips Semiconductors Product specification Silicon Diffused Power Transistor BU4507DZ GENERAL DESCRIPTION Enhanced performance, new generation, high-voltage, high-speed switching npn transistor with an integrated damper diode in a plastic full-pack envelope intended for use in horizontal deflection circuits of colour television receivers and p.c monitors. Features exceptional tolerance to base drive and collector current load variations resulting in a very low worst case dissipation. QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT VCESM VCEO IC ICM Ptot VCEsat ICsat VF tf Collector-emitter voltage peak value Collector-emitter voltage (open base) Collector current (DC) Collector current peak value Total power dissipation Collector-emitter saturation voltage Collector saturation current Diode forward voltage Fall time VBE = 0 V 4 1.7 300 1500 800 8 15 32 3.0 2.1 400 V V A A W V A V ns PINNING - SOT186A PIN Ths ≤ 25 ˚C IC = 4 A; IB = 1.0 A f = 16kHz IF = 4 A ICsat = 4 A; f = 16kHz PIN CONFIGURATION SYMBOL DESCRIPTION c case 1 base 2 collector 3 emitter b Rbe case isolated e 1 2 3 LIMITING VALUES Limiting values in accordance with the Absolute Maximum Rating System (IEC 134) SYMBOL PARAMETER CONDITIONS VCESM VCEO IC ICM IB IBM -IBM Ptot Tstg Tj Collector-emitter voltage peak value Collector-emitter voltage (open base) Collector current (DC) Collector current peak value Base current (DC) Base current peak value Reverse base current peak value 1 Total power dissipation Storage temperature Junction temperature VBE = 0 V Ths ≤ 25 ˚C MIN. MAX. UNIT -65 - 1500 800 8 15 4 6 5 32 150 150 V V A A A A A W ˚C ˚C TYP. MAX. UNIT - 4.0 K/W 55 - K/W THERMAL RESISTANCES SYMBOL PARAMETER CONDITIONS Rth j-hs Junction to heatsink with heatsink compound Rth j-a Junction to ambient in free air 1 Turn-off current. January 1999 1 Rev 1.000 Philips Semiconductors Product specification Silicon Diffused Power Transistor BU4507DZ ISOLATION LIMITING VALUE & CHARACTERISTIC Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS Visol R.M.S. isolation voltage from all three terminals to external heatsink f = 50-60 Hz; sinusoidal waveform; R.H. ≤ 65% ; clean and dustfree Cisol Capacitance from T2 to external f = 1 MHz heatsink MIN. TYP. - MAX. UNIT 2500 V - 10 - pF MIN. TYP. MAX. UNIT - - 1.0 2.0 mA mA 800 - - V 7.5 0.83 4.2 - 13.5 30 0.92 7 5.7 1.7 3.0 1.01 7.3 2.1 V Ω V V TYP. MAX. UNIT 3.7 300 4.6 400 µs ns STATIC CHARACTERISTICS Ths = 25 ˚C unless otherwise specified SYMBOL ICES ICES VCEOsust BVEBO Rbe VCEsat VBEsat hFE hFE VF PARAMETER Collector cut-off current CONDITIONS 2 VBE = 0 V; VCE = VCESMmax VBE = 0 V; VCE = VCESMmax Tj = 125 ˚C Collector-emitter sustaining voltage IB = 0 A; IC = 100 mA; L = 25 mH Emitter-base breakdown voltage IB = 600 mA Base-emitter resistance VEB = 6 V Collector-emitter saturation voltages IC = 4 A; IB = 1.0 A Base-emitter saturation voltage IC = 4 A; IB = 1.0 A DC current gain IC = 500 mA; VCE = 5 V IC = 4 A; VCE = 5 V Diode forward voltage IF = 4 A V DYNAMIC CHARACTERISTICS Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS ICsat = 4 A; IB1 = 0.8 A;(IB2 = -2 A) ts tf Switching times (16 kHz line deflection circuit) Turn-off storage time Turn-off fall time Anti-parallel diode forward recovery voltage Anti-parallel diode forward recovery time IF = 4 A; dIF/dt = 50 A/µs 18.5 - V VF = 5 V 500 - ns Vfr tfr 2 Measured with half sine-wave voltage (curve tracer). January 1999 2 Rev 1.000 Philips Semiconductors Product specification Silicon Diffused Power Transistor ICsat TRANSISTOR IC BU4507DZ + 150 v nominal adjust for ICsat DIODE t Lc IB1 IB t 20us 26us D.U.T. IB2 LB IBend Cfb 64us VCE -VBB Rbe t Fig.1. Switching times waveforms (16 kHz). Fig.4. Switching times test circuit. ICsat 100 hFE 90 % Ths = 25 C Ths = 85 C VCE = 1V IC 10 % tf 10 t ts IB IB1 t 1 0.01 - IB2 Fig.2. Switching times definitions. I I F 0.1 1 IC / A 10 Fig.5. High and low DC current gain. 100 F hFE BU4507DF/X/Z VCE = 5V Ths = 25 C Ths = 85 C 10% time t fr V 10 F V 5V V fr F 1 0.01 time Fig.3. Definition of anti-parallel diode Vfr and tfr. January 1999 0.1 1 IC / A 10 Fig.6. High and low DC current gain. 3 Rev 1.000 Philips Semiconductors Product specification Silicon Diffused Power Transistor BU4507DZ BU4507DF/X/Z 10 120 Normalised Power Derating PD% with heatsink compound 110 Ths = 25 C Ths = 85 C 100 90 80 70 1 60 50 40 IC/IB = 5 0.1 30 20 10 0 0 0.01 0.1 1 10 VBESAT \ V 40 60 80 Ths / C 100 120 140 Fig.10. Normalised power dissipation. PD% = 100⋅PD/PD 25˚C Fig.7. Typical collector-emitter saturation voltage. 1.2 20 100 BU4507DF/X/Z 10 Zth K/W BU4507AZ Ths = 25 C Ths = 85 C 1.1 0.5 1 0.2 1 0.1 0.05 0.1 0.9 0.02 IC = 4 A 0.8 PD 0.01 0.7 tp D= 0 T 0.6 tp T 0 1 2 3 IB / A 0.001 1.0E-07 4 1.0E-3 1.0E-01 t 1.0E+01 t/s Fig.8. Typical base-emitter saturation voltage. Fig.11. Transient thermal impedance. BU4507D ts/tf ts/tf/ us 10 1.0E-05 ICsat = 4 A Ths = 85 C Freq = 16 kHz 8 6 4 2 0 0 0.5 1 1.5 2 2.5 IB / A 3 Fig.9. Typical collector storage and fall time. IC =4 A; Tj = 85˚C; f = 16kHz January 1999 4 Rev 1.000 Philips Semiconductors Product specification Silicon Diffused Power Transistor BU4507DZ MECHANICAL DATA Dimensions in mm Net Mass: 2 g 10.3 max 4.6 max 3.2 3.0 2.9 max 2.8 Recesses (2x) 2.5 0.8 max. depth 6.4 15.8 19 max. max. 15.8 max seating plane 3 max. not tinned 3 2.5 13.5 min. 1 0.4 2 3 M 1.0 (2x) 0.6 2.54 0.9 0.7 0.5 2.5 5.08 1.3 Fig.12. SOT186A; The seating plane is electrically isolated from all terminals. Notes 1. Refer to mounting instructions for F-pack envelopes. 2. Epoxy meets UL94 V0 at 1/8". January 1999 5 Rev 1.000 Philips Semiconductors Product specification Silicon Diffused Power Transistor BU4507DZ DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. Philips Electronics N.V. 1999 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. January 1999 6 Rev 1.000