Previous Datasheet Index Next Data Sheet Data Sheet No. 1.1041 Series PVI5013R Solid-State Opto-Isolated MOSFET Gate Driver Dual-Channel 5V, 1.0µA PHOTOVOLTAIC ISOLATOR General Description PVI5013R Features The PVI5013R Photovoltaic Isolator is a dualchannel, opto-isolated driver capable of directly driving gates of power MOSFETs or IGBTs. It utilizes a monolithic integrated circuit photovoltaic generator of novel construction as its output. The output is controlled by radiation from a GaAlAs light emitting diode (LED) which is optically isolated from the photovoltaic generator. Monolithic construction ■ 3,750 VRMS I/O isolation ■ 1,200 VDC output-to-output isolation ■ Dual-Channel application flexibility ■ Solid-State reliability ■ UL and CSA certifications pending ■ The PVI5013R is ideally suited for applications requiring high-current and/or high voltage switching with optical isolation between the lowlevel driving circuitry and high-energy or highvoltage load circuits. It can be used for directly driving gates of power MOSFETs. The dualchannel configuration allows its outputs to drive independent discrete power MOSFETs, or be connected in parallel or in series to provide higher-current drive for power MOSFETs or higher-voltage drive for IGBTs. PVI5013R employs a fast turn-off circuitry. PVI5013R Photovoltaic Isolators are packaged in an 8-pin, molded DIP package with either thruhole or “gull-wing” terminals. It is available in standard plastic shipping tubes or on tape-andreel. Refer to Part Identification information. Applications Telecommunications Load Distribution Industrial Controls Instrumentation and Measurement Part Identification PVI5013R PVI5013RS PVI5013RS-T ■ ■ ■ ■ To Order thru-hole SMT SMT, T&R Previous Datasheet Index Next Data Sheet PVI5013R Electrical Specifications (-40°C ≤ TA ≤ +85°C unless otherwise specified) INPUT CHARACTERISTICS Limits Units Min. Input Current (See Fig.1) Input Current Range (See Fig. 1) Max. Continuous Input Current @ TA =+25°C LED Forward Voltage Drop @ 5mA, TA=+25°C (See Fig. 3) Max. Reverse Voltage Max. Reverse Current @ -7VDC , TA=+25°C 5.0 3.0 to 25 40 1.4 7.0 10 mA mA mA V V µA OUTPUT CHARACTERISTICS Limits Units 8.0 10 VDC µADC Limits Units 3 V 8 V 1.0 V 1.0 µA 5 0.25 100 3300 ms ms Ω Ω Limits Units 3750 1200 1012 VRMS VDC 5.0 +260 -40 to +85 -40 to +125 pF °C °C °C Min. Forward Voltage Max. Reverse Current COUPLED CHARACTERISTICS Min. Output Voltage @ ILED = 5mA, RL = 10MΩ @ TA=0°C to +70°C (See Fig. 1 & 2) Max. Output Voltage @ ILED = 5mA, RL = 10MΩ @ TA=0°C to +70°C (See Fig. 1 & 2) Max. Voltage Differential Between Outputs @ ILED = 5mA, RL = 10MΩ Typical Output Short-Circuit Current @ ILED = 5mA, @ T A=+25°C (See Fig. 1 & 2) Max. Turn-On Time @ ILED = 5mA, C LOAD = 200pF (See Fig. 4) Max. Turn-Off Time @ ILED = 5mA, CLOAD = 200pF (See Fig. 4) Off-State Clamping Resistance: minimum maximum GENERAL CHARACTERISTICS Min. Dielectric Strength, Input-Output Min. Dielectric Strength, Output-to-Output Min. Insulation Resistance, Input-to-Output @TA=+25°C, 50%RH, 100VDC Max. Capacitance, Input-Output Max. Pin Soldering Temperature (10 seconds max.) Ambient Temperature Range: Operating Storage Connection Diagram 1 8 (+) 2 7 (-) 3 6 (+) 4 5 (-) To Order Ω Previous Datasheet Index Next Data Sheet PVI5013R 12 9.0 1.2 Open Circuit Voltage Output Voltage (VDC) Rl=10MOhm 6.0 8 nt re ur tC 4.5 6 ui irc t-C or Sh 3.0 4 2 1.5 0 0 10 20 30 1.1 Normalized Output 7.5 Output Short-Circuit Current (uA) ILED=5mA 10 1.0 0.9 Output Voltage 0.8 0.7 Short-Circuit Current 0.6 0 40 0.5 -40 Input Current (mA) Figure 1. Typical Output Characteristics Max. device 4 TYPICAL 8 and -40 deg. C limit limit Min. device and +85 deg. C Input Current (mA) 16 12 20 40 60 80 100 5000 CAUTION: provide current limiting so that 25 mA maximum steadystate control current rating is not exceeded Response Time (microseconds) 20 0 -20 Ambient Temperature (deg. C) Figure 2. Typical Variation of Output ILED=5mA Ton 1000 500 100 Toff 0 0 0.5 1.0 1.5 50 100 2.0 LED Forward Voltage Drop (Volts DC) 200 300 400 Load Capacitance (pF) Figure 3. Input Characteristics (Current Controlled) To Order Figure 4. Typical Response Time 500 Previous Datasheet Index Next Data Sheet PVI5013R Mechanical Specifications (Dimensions in millimeters (inches)) 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 2. CONTROLLING DIMENSION: INCH 4 DIMENSION DOES NOT INCLUDE MOLD PROTRUSIONS. MOLD PROTRUSIONS SHALL NOT EXCEED 0.25 (.010). WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 322 3331 EUROPEAN HEADQUARTERS: Hurst Green, Oxted, Surrey RH8 9BB, UK Tel: (44) 0883 713215 IR CANADA: 7321 Victoria Park Ave., Suite 201, Markham, Ontario L3R 3L1, Tel: (905) 475 1897 IR GERMANY: Saalburgstrasse 157, 61350 Bad Homburg Tel: 6172 37066 IR ITALY: Via Liguria 49, 10071 Borgaro, Torino Tel: (39) 1145 10111 IR FAR EAST: K&H Bldg., 2F, 3-30-4 Nishi-Ikeburo 3-Chome, Toshima-Ki, Tokyo 171 Tel: (03)3983 0641 IR SOUTHEAST ASIA: 315 Outram Road, #10-02 Tan Boon Liat Building, Singapore 0316 Tel: 65 221 8371 http://www/irf.com/ Data and specifications subject to change without notice. 6/96 To Order