INTEGRATED CIRCUITS 74F711A, 74F711-1, 74F712A, 74F712-1 Multiplexers Product specification IC15 Data Handbook 1990 Dec 13 Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers 74F711A 74F711-1 74F712A 74F712-1 Quint 2-to-1 Data Selector Multiplexer (3-State) Quint 2-to-1 Data Selector Multiplexer with 30 Equivalent Output Termination Impedance (3-State) Quint 3-to-1 Data Selector Multiplexer Quint 3-to-1 Data Selector Multiplexer with 30 Equivalent Output Termination Impedance To improve speed and noise immunity, VCC and GND side pins are used. FEATURES for 74F711A/74F711-1 • Consists of five 2-to-1 Multiplexers • High impedance PNP base inputs for reduced loading The 74F712A/74F712-1 consist of five 3-to1 multiplexers designed for address multiplexing of dynamic RAMs and other multiplexing applications. The 74F712A has two select (S0, S1) inputs to determine which set of five inputs will be propagated to the five outputs. The outputs source 15mA and sink 64mA. The 74F712-1 is the same as the 74F712A except that it has a 30 termination impedance on each output to reduce line noise and the outputs sink 5mA. (20µA in High and Low states) • Designed for address multiplexing of dynamic RAM and other applications • Output inverting/non-inverting option • 30 termination impedance on each output – 74F711-1 • Outputs sink 64mA (74F711A only) FEATURES for 74F712A/74F712-1 • Consists of five 3-to-1 Multiplexers • High impedance PNP base inputs for reduced loading (20µA in High and Low states) • Designed for address multiplexing of dynamic RAM and other applications • 30 termination impedance on each output – 74F712-1 • Outputs sink 64mA (74F712A only) TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F711A 6.0ns 30mA 74F711-1 6.5ns 29mA 74F712A 6.5ns 25mA 74F712-1 6.5ns 25mA ORDERING INFORMATION DESCRIPTION The 74F711A/74F711-1 consist of five 2-to-1 multiplexers designed for address multiplexing of dynamic RAMs and other multiplexing applications. The 74F711A has a common select (S) input, an Output Enable (OE) input and an Output Inverting (INV) input to control the 3-State outputs. The outputs source 15mA and sink 64mA. The 74F711-1 is the same as the 74F711A except that is has a 30 termination impedance on each output to reduce line noise and the 3-State outputs sink 5mA. DESCRIPTION COMMERCIAL RANGE VCC = 5V ± 10% Tamb = 0° C to +70°C 20-Pin Plastic DIP N74F711AN, N74F711-1N SOT146-1 24-Pin Plastic Slim DIP (300 mil) N74F712AN, N74F712-1N SOT222-1 20-Pin Plastic SOL N74F711AD, N74F711-1D SOT163-1 24-Pin Plastic SOL N74F712AD, N74F712-1D SOT137-1 PKG DWG # When the inverting input (INV) is Low, the input data path is inverted. INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS 74F711A/ 74F711-1 74F712A/ 74F712-1 DESCRIPTION 74F(U.L.) HIGH/LOW LOAD VALUE HIGH/LOW Dna, Dnb Data inputs 1.0/0.066 20µA/40µA S Select input 1.0/0.033 20µA/20µA OE Output Enable input (active Low) 1.0/0.033 20µA/20µA INV Output inverting input (active Low) 1.0/0.033 20µA/20µA Q0 - Q4 Data outputs for 74F711A 750/106.7 15mA/64mA Q0 - Q4 Data outputs for 74F711-1 750/8.33 15mA/5mA Dna, Dnb, Dnc Data inputs 1.0/0.066 20µA/40µA S0, S1 Select inputs 1.0/0.033 20µA/20µA Q0 - Q4 Data outputs for 74F712A 750/106.7 15mA/64mA Q0 - Q4 Data outputs for 74F712-1 750/8.33 15mA/5mA NOTE: One (1.0) FAST Unit Load (U.L.) is defined as: 20µA in the High state and 0.6mA in the Low state. 1990 Dec 13 2 853-1368 01258 Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers PIN CONFIGURATION – 74F711A/74F711-1 PIN CONFIGURATION – 74F712A/74F712-1 D0a 1 20 D1a S0 1 24 D0a D0b 2 19 D1b S1 2 23 D1a Q0 3 18 D2a Q0 3 22 D2a Q1 4 17 D2b Q1 4 21 D3a GND 5 16 VCC Q2 5 20 D4a Q2 6 15 D3a GND 6 19 VCC Q3 7 14 D3b Q3 7 18 D0b Q4 8 13 D4a Q4 8 17 D1b S 9 12 D4b D0c 9 16 D2b 11 OE D1c 10 15 D3b 11 14 D4b D3c 12 13 D4c INV 10 D2c SF01215 SF01216 LOGIC SYMBOL – 74F711A/74F711-1 1 2 20 19 18 17 15 14 LOGIC SYMBOL – 74F712A/74F712-1 13 12 24 D0a D0b D1a D1b D2a D2b D3a D3b D4a D4b 9 23 17 10 22 16 11 21 15 12 20 14 13 D0a D0b D0c D1a D1b D1c D2a D2b D2c D3a D3b D3c D4a D4b D4c S 9 10 OE 1 S0 11 INV 2 S1 Q0 Q1 Q2 Q3 Q4 3 4 6 7 8 VCC = Pin 16 GND = Pin 5 SF01217 11 10 2 EN1 1 24 18 9 23 17 10 22 16 3 4 18 17 6 11 21 15 12 20 14 13 15 14 7 13 12 Q3 Q4 3 4 5 7 8 SF01218 G1 G2 M 20 19 Q2 MUX 1 G 1 2 Q1 LOGIC SYMBOL (IEEE/IEC) – 74F712A/74F712-1 MUX 1 Q0 VCC = Pin 19 GND = Pin 6 LOGIC SYMBOL (IEEE/IEC) – 74F711A/74F711-1 8 SF01219 1990 Dec 13 18 3 4 5 7 8 SF01220 3 Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers LOGIC DIAGRAM – 74F711A/74F711-1 11 OE 10 INV 9 S D0a 3 2 D0b D1a D2a 4 D3a 6 D4a 7 8 12 INPUTS OUTPUT S INV OE Dna Dnb Qn L L L Data a Data b Data a H L L Data a Data b Data b L H L Data a Data b Data a H H L Data a Data b Data b X Z X H X High voltage level Low voltage level Don’t care High impedance “off” state 1990 Dec 13 Q4 SF01221 FUNCTION TABLE – 74F711A/74F711-1 X = = = = Q3 13 VCC = Pin 16 GND = Pin 5 H L X Z Q2 15 14 D3b Q1 18 17 D2b Q0 20 19 D1b D4b 1 4 Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers LOGIC DIAGRAM – 74F712A/74F712-1 1 S0 2 S1 D0a 24 18 D0b D0c D1a 3 Q0 9 23 17 D1b D1c D2a 4 Q1 10 22 16 D2b D2c D3a 5 21 15 D3b Q2 11 7 Q3 D3c 12 D4a D4b 20 14 8 Q4 D4c 13 VCC = Pin 19 GND = Pin 6 SF01222 FUNCTION TABLE – 74F712A/74F712-1 INPUTS OUTPUT S0 S1 Dna Dnb Dnc Qn L L Data a Data b Data c Data a H L Data a Data b Data c Data b X H Data a H = High voltage level L = Low voltage level X = Don’t care Data b Data c Data c 1990 Dec 13 5 Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers ABSOLUTE MAXIMUM RATINGS Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range. SYMBOL PARAMETER RATING UNIT V VCC Supply voltage –0.5 to +7.0 VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state IOUT O Current applied to output in Low output state Tamb Operating free-air temperature range Tstg Storage temperature –0.5 to +VCC V 74F711A, 74F712A 96 mA 74F711-1, 74F712-1 10 mA 0 to +70 °C –65 to +150 °C LIMITS UNIT RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER MIN NOM MAX VCC Supply voltage 4.5 5.0 5.5 VIH High-level input voltage 2.0 VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –15 mA IOL O Low level output current Low-level 74F711A, 74F712A 64 mA 74F711-1, 74F712-1 5 mA Tamb Operating free-air temperature 70 °C 1990 Dec 13 0 6 V V Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL VOH O VOL IOH 3mA O = –3mA VCC = MIN, VIL = MAX MAX, VIH = MIN High level output voltage High-level Low-level output voltage g LIMITS TEST CONDITIONS1 PARAMETER 74F711A/ 74F712A only 74F711-1/ 74F712-1 15mA IOH O = –15mA IOL O = MAX VCC = MIN, VIL = MAX,, VIH = MIN IOL = 5mA MIN ±10%VCC 2.4 TYP2 UNIT MAX V ±5%VCC 2.7 ±10%VCC 2.0 V ±5%VCC 2.0 V 3.4 V ±10%VCC 0.38 0.55 V ±5%VCC 0.42 0.55 V ±10%VCC 0.38 0.50 V –0.73 –1.2 V VIK Input clamp voltage VCC = MIN, II = IIK II Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low level input current Low-level –20 µA –40 µA IOZH Off-state output current High-level voltage applied 50 µA IOZL Off-state output current Low-level voltage applied –50 µA IOS Short-circuit output current3 74F711-1/ 74F712-1 VCC = MAX –60 –150 mA IO Output current4 74F711A/ 74F712A VCC = MAX, VO = 2.25 V –60 –150 mA 25 35 mA 33 46 mA ICCZ 27 40 mA ICCH 26 40 mA 33 45 mA 28 45 mA 20 27 mA 30 40 mA 20 30 mA Others Dn only 74F711A/ 74F711 1 74F711-1 only VCC = MAX, MAX VI = 0 0.5V 5V VCC = MAX, VO = 2.7V VCC = MAX, VO = 0.5V ICCH 74F711A ICC Supply current ((total)) 74F711-1 ICCL ICCL VCC = MAX VCC = MAX ICCZ 74F712A ICCH ICCL 74F712 1 74F712-1 ICCH VCC = MAX VCC = MAX ICCL 29 40 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. 4. IO is tested under conditions that produce current approximity one half of the true short-circuit output current (IOS). 1990 Dec 13 7 Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers AC ELECTRICAL CHARACTERISTICS – 74F711A/74F711-1 LIMITS SYMBOL PARAMETER Tamb = +25°C VCC = 5V CL = 50pF, 50pF RL = 500 TEST CONDITION Tamb = 0° C to +70°C VCC = 5V ± 10% CL = 50pF, RL = 500 UNIT MIN TYP MAX MIN MAX Waveform 1, 2 2.5 2.5 5.0 4.0 7.5 7.0 2.0 2.0 8.0 7.5 ns ns Waveform 1, 3 7.0 5.0 9.0 8.0 12.0 11.0 5.5 4.5 13.5 12.0 ns ns Waveform 1, 3 6.0 4.0 9.0 8.0 12.5 11.0 5.0 3.5 14.0 11.5 ns ns Output Enable time OE to Qn Waveform 4 Waveform 5 2.5 2.5 4.0 4.5 6.5 7.0 2.0 2.0 7.0 7.5 ns ns tPHZ tPLZ Output Disable time OE to Qn Waveform 4 Waveform 5 2.5 3.0 4.0 5.0 7.0 8.0 2.0 2.5 8.0 8.5 ns ns tPLH tPHL Propagation delay Dna, Dnb to Qn Waveform 1, 2 3.0 2.0 4.5 4.5 7.5 7.5 2.0 2.5 9.0 8.0 ns ns tPLH tPHL Propagation delay S, INV to Qn Waveform 1, 3 6.5 4.5 10.0 8.5 13.5 11.5 5.5 4.0 14.5 12.5 ns ns tPZH tPZL Output Enable time OE to Qn Waveform 4 Waveform 5 2.5 3.0 4.5 5.0 7.5 7.5 2.0 2.5 9.0 8.0 ns ns tPHZ tPLZ Output Disable time OE to Qn Waveform 4 Waveform 5 2.0 3.5 4.5 5.5 7.0 8.5 2.0 3.0 8.0 9.5 ns ns tPLH tPHL Propagation delay Dna, Dnb to Qn tPLH tPHL Propagation delay S to Qn tPLH tPHL Propagation delay INV to Qn tPZH tPZL 74F711A 74F711 1 74F711-1 AC ELECTRICAL CHARACTERISTICS – 74F712A/74F712-1 LIMITS SYMBOL PARAMETER tPLH tPHL Propagation delay Dna, Dnb, Dnc to Qn tPLH tPHL Propagation delay S0, S1 to Qn tPLH tPHL Propagation delay Dna, Dnb, Dnc to Qn tPLH tPHL Propagation delay S0, S1 to Qn 1990 Dec 13 TEST CONDITION Tamb = +25°C VCC = 5V 50pF RL = 500 CL = 50pF, Tamb = 0 to +70°C VCC = 5V ± 10% CL = 50pF, RL = 500 UNIT MIN TYP MAX MIN MAX Waveform 1, 2 2.0 2.0 3.5 3.5 6.5 6.5 2.0 2.0 7.0 7.0 ns ns Waveform 1 6.5 5.0 8.0 7.5 11.5 10.0 5.5 4.5 13.5 11.0 ns ns Waveform 1, 2 2.0 2.0 4.0 4.0 7.0 7.0 2.0 2.0 7.5 7.5 ns ns Waveform 1 7.0 5.5 9.0 7.5 12.0 10.5 6.0 5.5 13.5 11.0 ns ns 74F712A 74F712 1 74F712-1 8 Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers AC WAVEFORMS For all waveforms, VM = 1.5V Dna, Dnb, Dnc, Sn VM Dna, Dnb, Dnc, Sn VM tPLH VM tPHL Qn VM VM tPHL VM tPLH Qn VM VM SF01223 SF01224 Waveform 1. Propagation Delay for Non-Inverting Output INV Waveform 2. Propagation Delay for Inverting Output OE VM VM VM tPZH tPHL Qn tPLH tPHZ VOH -0.3V VM 0V Qn SF00343 VM Waveform 4. 3-State Output Enable Time to High Level and Output Disable Time from High Level SF01225 Waveform 3. Propagation Delay for INV to Output VM OE VM tPZL tPLZ VM Qn VOL +0.3V SF00344 Waveform 5. 3-State Output Enable Time to Low Level and Output Disable Time from Low Level 1990 Dec 13 9 Philips Semiconductors Product specification 74F711A/74F711–1/ 74F712A/74F712–1 Multiplexers TEST CIRCUIT AND WAVEFORMS VCC 7.0V VIN RL VOUT PULSE GENERATOR tw 90% NEGATIVE PULSE VM CL AMP (V) VM 10% D.U.T. RT 90% 10% tTHL (tf ) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0V RL AMP (V) 90% 90% Test Circuit for 3-State Outputs POSITIVE PULSE VM VM 10% TEST tPLZ tPZL All other SWITCH closed closed open DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. 10% tw SWITCH POSITION 0V Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns SF00777 1990 Dec 13 10 Philips Semiconductors Product specification 74F711A/74F711-1, 74F712A/74F712-1 Multiplexers DIP20: plastic dual in-line package; 20 leads (300 mil) 1990 Dec 13 11 SOT146-1 Philips Semiconductors Product specification 74F711A/74F711-1, 74F712A/74F712-1 Multiplexers DIP24: plastic dual in-line package; 24 leads (300 mil) 1990 Dec 13 12 SOT222-1 Philips Semiconductors Product specification 74F711A/74F711-1, 74F712A/74F712-1 Multiplexers SO20: plastic small outline package; 20 leads; body width 7.5 mm 1990 Dec 13 13 SOT163-1 Philips Semiconductors Product specification 74F711A/74F711-1, 74F712A/74F712-1 Multiplexers SO24: plastic small outline package; 24 leads; body width 7.5 mm 1990 Dec 13 14 SOT137-1 Philips Semiconductors Product specification 74F711A/74F711-1, 74F712A/74F712-1 Multiplexers NOTES 1990 Dec 13 15 Philips Semiconductors Product specification 74F711A/74F711-1, 74F712A/74F712-1 Multiplexers Data sheet status Data sheet status Product status Definition [1] Objective specification Development This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. Preliminary specification Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 print code Document order number: yyyy mmm dd 16 Date of release: 10-98 9397-750-05174