RECOM RACD12-500

Features
LED
DRIVER
●
●
●
●
●
●
●
●
●
●
●
LIGHTLINE
12W Class II AC/DC LED Power Supply
350mA or 700mA Constant Current Output
Drives 1 - 10 High Brightness LEDs
Universal AC Input
Active Power Factor Corrected >0.95
Fused Input, Protected Output
3kVAC Input/Output Isolation
Output Socket Connector
cUL/UL-8750 Certified
Low Cost
Long 5 Year Warranty
AC/DC-Converter
with 5 year Warranty
Description
A compact 12W constant current switching power module suitable for driving up to ten high power LEDs (Vf = 3.6V).
The output current is fixed at 350mA, 500mA or 700mA. Active power factor correction is standard and the converters
are UL8750 certified for use with LED assemblies. The driver modules features both screw terminal and socket output
connections. The socket connecter avoids the possibility of miswiring and damaging the LED load if the LEDs are preassembled into a wiring harness or lamp fitting.
12 Watt PFC
Single
Output
E340696
Selection Guide
Part
Number
Nominal
Input Voltage
(VAC)
Input Current
at 230VAC
(mA)
Output
Output
Voltage Range Current
(VDC)
(mA)
Max
#
LEDs
RACD12-350
universal
200
3-36
350
10 x 1W
RACD12-500
universal
200
3-24
500
6 x 2W
RACD12-700
universal
200
3-17
700
4 x 2W, 8 x 1W
RACD12
Specifications (typical at 25°C and after warm up time unless otherwise specified )
Input Voltage Range
90VAC-264VAC
Rated Power
12 Watts max.
Input Frequency Range
Power Factor
Open Circuit Voltage
(Zener Clamp)
Full Load, 115VAC/230VAC
39VDC
26VDC
19VDC
Inrush Current (<2mS)
115VAC/230VAC
10A max.
Input Current
230VAC, Full Load
Leakage Current
Input Fuse
115VAC/240VAC - 60/50Hz
Standard
Output Current Accuracy
(combined Tolerance, Load Regulation and Line Regulation)
Minimum Load
Open Circuit Protected
200mA max.
0.5mA typ.
T1A
±10%.
1 LED
Output Ripple
150mA max.
Hold Up Time
18ms min.
Operating Frequency
50-120kHz typ.
Efficiency at Full Load
RMS Isolation Voltage (input to output)
78%
3kVAC / 1 minute
Temperature Coefficient
±0.02%/°C typ.
Overload Protection
120% typ.
Continuous Current Limit
Zener Diode Clamp
continued on next page
18
RACD12
0.95
350mA Version
500mA Version
Output Overvoltage Protection
UL-8750 Certified
cUL-8750 Certified
EN 61347 Certified
47-63 Hz
700mA Version
Short Circuit Protection
RoHS
2002/95/EC
6/6
REV: 3/2011
Please Read Application Notes
www.recom-electronic.com
LIGHTLINE
RACD12
AC/DC-Converter
Specifications cont. (typical at 25°C and after warm up time unless otherwise specified )
Overtemperature Protection
Operating Temperature Range
(free air convection)
Weight
Shutdown, Automatic restart after cooling down
Ambient Temperature
-20°C to +50°C
Case Temperature
85°C max.
100g
Packing Quantity
1pc
Storage Temperature Range
-40°C to +100°C
Humidity
95% RH max.
IP Rating
IP20, Indoor Use Only
PCB Material
Case Material
Designed to meet Standards
THD
Certifications
Design Lifetime
Connections
Plastic Resin with Fibreglass (UL94V-0)
Plastic
EN55015:2006 + A1: 2007 + A2:2009
EN 61000-3-2:2006
EN 61000-3-3:2006
EN 61547:1995 + A1:2000
complies with UL1310
complies with FCC18A
<20%
LED Lighting Safety
UL8750
LED Lighting Safety (Canada)
cUL8750
SEMKO CE Certification, General Safety
EN 61347-1: 2008
SEMKO CE Certification, Safety of AC supplied Control Gear for LED Modules
EN 61347-2-13: 2006
Electrical Lighting, EMC Emissions
Limits for Harmonics Emissions
EMC Compatibilty: Flicker and Voltage Variations
Electrical Lighting: EMC Immunity
Class II Power Supply Safety
FCC
25°C ambient
AC Input
LED Output
LED Output
>70 x 10³ hours in operation
Screw terminal
Screw Terminal
5.5mm Socket with 2mm Pin (Suitable matching plug Switchcraft S760 or similar)*
RACD12
* Do not connect or disconnect the LED load while the converter is on. This may damage the LED or reduce its life.
Package Style and Pinning
3rd angle
projection
117
5.5mm socket
26
Tc
45.0
39
Cable entry
with strain relief
Connections
3.5mm dia.
70
123.0
18.5
15.5
2 Mounting screws are included
Tc= Case Temperature Measuring Point
CN1
Function
L
VAC in (L)
N
VAC in (N)
CN2
Function
+
LED+
-
LED-
5.5mm Socket* Function
Pin
LED+
Shell
LED-
Tolerenace
XX = +/-0.5mm
XX.X =+/-0.25mm
www.recom-international.com
REV:3/2011
19