PHILIPS TDA19978B

TDA19978B
Quad HDMI 1.3a receiver interface with equalizer (HDTV up to
1080p, up to UXGA for PC formats)
Rev. 02 — 10 May 2010
Product data sheet
1. General description
The TDA19978B is a four input HDMI 1.3a compliant receiver with embedded EDID
memory. The built-in auto-adaptive equalizer improves signal quality and allows the use of
cable lengths up to 25 m which are laboratory tested with a 0.5 mm (24 AWG) cable at
2.05 gigasamples per second. In addition, the TDA19978B is delivered with software
drivers to ease configuration and use.
The TDA19978B supports:
• TV resolutions:
– 480i (1440 × 480i at 60 Hz), 576i (1440 × 576i at 50 Hz) to HDTV (up to
1920 × 1080p at 50/60 Hz)
– WUXGA (1920 × 1200p at 60 Hz) reduced blanking format
• PC resolutions:
– VGA (640 × 480p at 60 Hz) to UXGA (1600 × 1200p at 60 Hz)
• Deep Color mode in 10-bit and 12-bit (up to 205 MHz TMDS clock)
• Gamut boundary description
• IEC 60958/IEC 61937, OBA (One Bit Audio), DST (Direct Stream Transfer) and HBR
(High Bit Rate) stream
The TDA19978B includes:
• An enhanced PC and TV format recognition system
• Generation of a 128/256/512 × fs system clock allowing the use of simple audio DACs
without an integrated PLL (such as the UDA1334BTS)
• An embedded oscillator (an external crystal can also be used)
• Improved audio clock generation using an external reference clock
• OBA (as used in SACD), DST and HBR stream support
The TDA19978B converts HDMI streams without HDCP into RGB or YCbCr digital
signals. The YCbCr digital output signal can be 4:4:4 or 4:2:2 semi-planar format based
on the ITU-R BT.601 standard or 4:2:2 based on the ITU-R BT.656 format. The device can
adjust the output timing of the video port by altering the values of tsu(Q) and th(Q). In
addition, all settings are controllable using the I2C-bus.
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
2. Features and benefits
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
TDA19978B_2
Product data sheet
Complies with the HDMI 1.3a, DVI 1.0 and CEA-861-D
Four (quad) independent HDMI inputs, up to the HDMI frequency of 205 MHz
Embedded auto-adaptive equalizer on all HDMI links
EDID memory: 253 shared bytes and three bytes dedicated to each HDMI input
Supports color depth processing (8-bit, 10-bit or 12-bit per color)
Color gamut metadata packet with interrupt on each update, readable via the I2C-bus
Up to four S/PDIF or I2S-bus outputs (eight channels) at a sampling rate up to 192 kHz
with IEC 60958/IEC 61937 stream
HBR audio stream up to 768 kHz with four demultiplexed S/PDIF or I2S-bus outputs
HBR streams (e.g. DTS-HD master audio and Dolby TrueHD up to eight channels due
to HBR packet for stream with a frame rate up to 768 kHz) support
DSD and DST audio stream up to six DSD channels output for SACD with DST audio
packet support
Channel status decoder supports multi-channel reception
Improved audio clock generation using an external reference clock
System/master clock output (128/256/512 × fs) enables the use of the UDA1334BTS
The HDMI interface supports:
‹ All HDTV formats up to 1920 × 1080p at 50/60 Hz and WUXGA (1920 × 1200p at
60 Hz) with support for reduced blanking
‹ PC formats up to UXGA (1600 × 1200p at 60 Hz)
Embedded oscillator (an external crystal can be used)
Frame and field detection for interlaced video signal
Sync timing measurements for format recognition
Improved system for measurements of blanking and video active area allowing an
accurate recognition of PC and TV formats
Repeater capability
Programmable color space input signal conversion from RGB-to-YCbCr or
YCbCr-to-RGB
Output formats: RGB 4:4:4, YCbCr 4:4:4, YCbCr 4:2:2 semi-planar based on the
ITU-R BT.601 standard and YCbCr 4:2:2 ITU-R BT.656
8-bit, 10-bit or 12-bit output formats selectable using the I2C-bus (8-bit and 10-bit only
in 4:4:4 format)
I2C-bus adjustable timing of video port (tsu(Q) and th(Q))
Downsampling-by-two with selectable filters on Cb and Cr channels in 4:2:2 mode
Internal video and audio pattern generator
Controllable using the I2C-bus; 5 V tolerant and bit rate up to 400 kbit/s
DDC-bus inputs 5 V tolerant and bit rate up to 400 kbit/s
LV-TTL outputs
Power-down mode
CMOS process
1.8 V and 3.3 V power supplies
Lead-free (Pb) HLQFP144 package
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
2 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
3. Applications
„
„
„
„
„
„
„
„
HDTV
YCbCr or RGB high-speed video digitizer
Projector, plasma and LCD TV
Rear projection TV
High-end TV
Home theater amplifier
DVD recorder
AVR and HDMI splitter
4. Quick reference data
Table 1.
Quick reference data
Symbol
Parameter
Conditions
Digital inputs: pins RXxC+,
fclk(max)
Min
Typ Max
Unit
205
-
-
MHz
pin VCLK
165
-
-
MHz
pin ACLK
25
-
-
MHz
pin SYSCLK
50
-
-
MHz
RXxC−[1]
maximum clock frequency
Clock timing output: pins VCLK, ACLK and SYSCLK
fclk(max)
maximum clock frequency
Supplies
VDDH(3V3) HDMI supply voltage (3.3 V)
3.135 3.3
3.465 V
VDDH(1V8) HDMI supply voltage (1.8 V)
1.71
1.89
VDDI(3V3)
input supply voltage (3.3 V)
VDDC(1V8) core supply voltage (1.8 V)
VDDO(3V3) output supply voltage (3.3 V)
P
power dissipation
Pcons
power consumption
[1]
x = A, B, C or D.
[2]
At 30 % activity on video port output.
1.8
3.465 V
1.71
1.89
1.8
3.135 3.3
Active mode
V
3.135 3.3
V
3.465 V
[2]
720p at 60 Hz
-
0.75 -
W
1080p at 60 Hz
-
1.13 -
W
1080p at 60 Hz; Deep Color mode
-
1.63 -
W
pin PD = HIGH
-
1
-
mW
I2C-bus;
EDID
-
4
-
mW
I2C-bus;
EDID; activity detection
-
150
-
mW
Power-down mode
5. Ordering information
Table 2.
Ordering information
Type number
TDA19978BHV
TDA19978B_2
Product data sheet
Package
Name
Description
Version
HLQFP144
plastic thermal enhanced low profile quad flat package;
144 leads; body 20 × 20 × 1.4 mm; exposed die pad
SOT612-3
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
3 of 38
xxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx x xxxxxxxxxxxxxx xxxxxxxxxx xxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx
xxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxx x x
AUDIO
PLL
AUDIO
FORMATTER
RRX1
HDMI C (channel C)
HDMI D (channel D)
XTALIN/MCLK
XTALOUT
PACKET
EXTRACTION
TERMINATION
RESISTANCE
CONTROL
EQUALIZER
RRX2
HDMI D (channels 0/1/2)
OTP
MEMORY
HDMI
RECEIVER
COLOR
DEPTH
UNPACKING
TERMINATION
RESISTANCE
CONTROL
AUDIO
FIFO
VIDEO
OUTPUT
FORMATTER
TDA19978B
SYNC
TIMING
MEASUREMENT
Block diagram of TDA19978B
HS/HREF
VS/VREF
CS/FREF
HSDAA/
HSCLA
HSDAB/
HSCLB
HSDAC/
HSCLC
HSDAD/
HSCLD
001aai415
TDA19978B
4 of 38
© NXP B.V. 2010. All rights reserved.
Fig 1.
VCLK
DE
VHREF
TIMING
GENERATOR
I2C-BUS SLAVE
INTERFACE
SDA/SCL
VP[29:0]
POWER
MANAGEMENT
EDID
MEMORY
CRYSTAL
OSCILLATOR
UPSAMPLER
HDMI C (channels 0/1/2)
TERMINATION
RESISTANCE
CONTROL
Quad HDMI 1.3a receiver with digital processing
Rev. 02 — 10 May 2010
All information provided in this document is subject to legal disclaimers.
HDMI B (channel B)
ACLK
AP5/SYSCLK
DEREPEATER
HDMI B (channels 0/1/2)
AP0 to AP3
NXP Semiconductors
HDMI A (channel A)
AP4/WS
TERMINATION
RESISTANCE
CONTROL
6. Block diagram
TDA19978B_2
Product data sheet
HDMI A (channels 0/1/2)
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
7. Pinning information
109
144
7.1 Pinning
1
TDA19978BHV
Fig 2.
73
72
37
36
108
001aai416
Pin configuration for TDA19978B
7.2 Pin description
Table 3.
Symbol
TDA19978B_2
Product data sheet
Pin description
Pin
Type[1] Description
VSSC
1
G
ground for the digital core
PD
2
I
power-down control input (active HIGH)
VDDH(3V3)
3
P
HDMI receiver supply voltage; 3.3 V
RXDC+
4
I
HDMI input D positive clock channel
RXDC−
5
I
HDMI input D negative clock channel
VSSH
6
G
HDMI receiver ground
RXCC−
7
I
HDMI input C negative clock channel
RXCC+
8
I
HDMI input C positive clock channel
VDDH(3V3)
9
P
HDMI receiver supply voltage; 3.3 V
RXD0+
10
I
HDMI input D positive data channel 0
RXD0−
11
I
HDMI input D negative data channel 0
VSSH
12
G
HDMI receiver ground
RXC0−
13
I
HDMI input C negative data channel 0
RXC0+
14
I
HDMI input C positive data channel 0
VDDH(1V8)
15
P
HDMI receiver supply voltage; 1.8 V
RXD1+
16
I
HDMI input D positive data channel 1
RXD1−
17
I
HDMI input D negative data channel 1
VSSH
18
G
HDMI receiver ground
RXC1−
19
I
HDMI input C negative data channel 1
RXC1+
20
I
HDMI input C positive data channel 1
VDDH(3V3)
21
P
HDMI receiver supply voltage; 3.3 V
RXD2+
22
I
HDMI input D positive data channel 2
RXD2−
23
I
HDMI input D negative data channel 2
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
5 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 3.
Pin description …continued
Symbol
Pin
Type[1] Description
VSSH
24
G
HDMI receiver ground
RXC2−
25
I
HDMI input C negative data channel 2
RXC2+
26
I
HDMI input C positive data channel 2
VPP
27
P
OTP memory programming voltage[2]
VDDC(1V8)
28
P
digital core supply voltage; 1.8 V
VDDO(3V3)
29
P
video port output supply voltage; 3.3 V
VCLK
30
O
video clock output
VSSO
31
G
video port output ground
CS/FREF
32
O
composite synchronization output
composite field output signal
VS/VREF
33
O
vertical synchronization output
vertical reference output
HS/HREF
34
O
horizontal synchronization output
horizontal reference output
TDA19978B_2
Product data sheet
DE
35
O
data enable output
VP[0]
36
O
video port output bit 0
VSSC
37
G
digital core ground
VP[1]
38
O
video port output bit 1
VP[2]
39
O
video port output bit 2
VP[3]
40
O
video port output bit 3
VDDO(3V3)
41
P
video port output supply voltage; 3.3 V
VDDC(1V8)
42
P
digital core supply voltage; 1.8 V
VSSO
43
G
video port output ground
VP[4]
44
O
video port output bit 4
VP[5]
45
O
video port output bit 5
VP[6]
46
O
video port output bit 6
VP[7]
47
O
video port output bit 7
VP[8]
48
O
video port output bit 8
VP[9]
49
O
video port output bit 9
VP[10]
50
O
video port output bit 10
VP[11]
51
O
video port output bit 11
VDDO(3V3)
52
P
video port output supply voltage; 3.3 V
VP[12]
53
O
video port output bit 12
VSSO
54
G
video port output ground
VP[13]
55
O
video port output bit 13
VP[14]
56
O
video port output bit 14
VP[15]
57
O
video port output bit 15
VP[16]
58
O
video port output bit 16
VP[17]
59
O
video port output bit 17
VP[18]
60
O
video port output bit 18
VP[19]
61
O
video port output bit 19
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
6 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 3.
Pin description …continued
Symbol
Pin
Type[1] Description
VP[20]
62
O
video port output bit 20
VDDO(3V3)
63
P
video port output supply voltage; 3.3 V
VDDC(1V8)
64
P
digital core supply voltage; 1.8 V
VSSO
65
G
video port output ground
VP[21]
66
O
video port output bit 21
VP[22]
67
O
video port output bit 22
VP[23]
68
O
video port output bit 23
VP[24]
69
O
video port output bit 24
VP[25]
70
O
video port output bit 25
VP[26]
71
O
video port output bit 26
VP[27]
72
O
video port output bit 27
VSSC
73
G
digital core ground
VDDO(3V3)
74
P
video port output supply voltage; 3.3 V
VP[28]
75
O
video port output bit 28
VP[29]
76
O
video port output bit 29
VSSO
77
G
video port output ground
ACLK
78
O
audio clock output
AP0
79
O
audio port 0 output
AP1
80
O
audio port 1 output
AP2
81
O
audio port 2 output
AP3
82
O
audio port 3 output
AP4/WS
83
O
audio port 4 output
VDDO(3V3)
84
P
video port output supply voltage; 3.3 V
AP5/SYSCLK
85
O
audio port 5 output
VSSO
86
G
video port output ground
VDDH(3V3)
87
P
HDMI audio PLL supply voltage; 3.3 V
VDDH(3V3)
88
P
HDMI audio PLL supply voltage; 3.3 V
VSSH
89
G
HDMI audio PLL ground
VDDH(1V8)
90
P
HDMI audio PLL supply voltage; 1.8 V
VSSH
91
G
HDMI audio PLL ground
VDDC(1V8)
92
P
digital core supply voltage; 1.8 V
word select output
system clock audio output
XTALOUT
93
O
crystal oscillator output
XTALIN/MCLK
94
I
crystal oscillator input
test pattern clock input
TDA19978B_2
Product data sheet
VDDI(3V3)
95
P
digital inputs supply voltage; 3.3 V
VAI
96
O
video activity indication output (open-drain); warns the
external microprocessor that a special event has
occurred; must be connected to a pull-up resistor; 5 V
tolerant (active LOW)
SDA
97
I/O
I2C-bus serial data input/output
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
7 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 3.
TDA19978B_2
Product data sheet
Pin description …continued
Symbol
Pin
Type[1] Description
SCL
98
I
I2C-bus serial clock input
HSDAA
99
I/O
HDMI input/output A DDC-bus serial data
HSCLA
100
I
HDMI input A DDC-bus serial clock
HSDAB
101
I/O
HDMI input/output B DDC-bus serial data
HSCLB
102
I
HDMI input B DDC-bus serial clock
TEST0
103
I
reserved for test; connect to digital inputs ground (VSSC)
VDDH(3V3)
104
P
HDMI deep PLL supply voltage; 3.3 V
VSSH
105
G
HDMI deep PLL ground
RRX1
106
I
HDMI inputs A and B termination resistance control
VDDC(1V8)
107
P
digital core supply voltage; 1.8 V
VDDH(1V8)
108
P
HDMI receiver supply voltage; 1.8 V
VSSC
109
G
digital core ground
A0
110
I
I2C-bus address control input
VDDH(3V3)
111
P
HDMI receiver supply voltage; 3.3 V
RXBC+
112
I
HDMI input B positive clock channel
RXBC−
113
I
HDMI input B negative clock channel
VSSH
114
G
HDMI receiver ground
RXAC−
115
I
HDMI input A negative clock channel
RXAC+
116
I
HDMI input A positive clock channel
VDDH(3V3)
117
P
HDMI receiver supply voltage; 3.3 V
RXB0+
118
I
HDMI input B positive data channel 0
RXB0−
119
I
HDMI input B negative data channel 0
VSSH
120
G
HDMI receiver ground
RXA0−
121
I
HDMI input A negative data channel 0
RXA0+
122
I
HDMI input A positive data channel 0
VDDH(1V8)
123
P
HDMI receiver supply voltage; 1.8 V
RXB1+
124
I
HDMI input B positive data channel 1
RXB1−
125
I
HDMI input B negative data channel 1
VSSH
126
G
HDMI receiver ground
RXA1−
127
I
HDMI input A negative data channel 1
RXA1+
128
I
HDMI input A positive data channel 1
VDDH(3V3)
129
P
HDMI receiver supply voltage; 3.3 V
RXB2+
130
I
HDMI input B positive data channel 2
RXB2−
131
I
HDMI input B negative data channel 2
VSSH
132
G
HDMI receiver ground
RXA2−
133
I
HDMI input A negative data channel 2
RXA2+
134
I
HDMI input A positive data channel 2
VSSH
135
G
HDMI receiver ground
VDDC(1V8)
136
P
digital core supply voltage; 1.8 V
VDDC(1V8)
137
P
digital core supply voltage; 1.8 V
HSDAC
138
I/O
HDMI input/output C DDC-bus serial data
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
8 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 3.
Pin description …continued
Symbol
Pin
Type[1] Description
HSCLC
139
I
HDMI input C DDC-bus serial clock
HSDAD
140
I/O
HDMI input/output D DDC-bus serial data
HSCLD
141
I
HDMI input D DDC-bus serial clock
VDDI(3V3)
142
P
digital inputs supply voltage; 3.3 V
RRX2
143
I
HDMI inputs C and D termination resistance control
VDDH(1V8)
144
P
HDMI receiver supply voltage; 1.8 V
Exposed die pad
-
G
exposed die pad; connect to digital core ground (VSSC)
[1]
P = power supply; G = ground; I = input; O = output and I/O = input/output.
[2]
Connected to the ground of the HDMI receiver (VSSH) in normal operation.
8. Functional description
The TDA19978B converts digital data streams input by the HDMI sources into parallel
digital data for use by media and video signal processing integrated circuits in devices for
HDTV. Data streams can be decoded without HDCP protection.
Outputs from the TDA19978B can be RGB 4:4:4, YCbCr 4:4:4, YCbCr 4:2:2 semi-planar
format based on the ITU-R BT.601 standard or YCbCr 4:2:2 based on the ITU-R BT.656
format. Inputs can be both progressive and interlaced formats. The TDA19978B
comprises a color space conversion block, downsampling filters and an embedded timing
code function. In addition, the repeater function enables other HDMI devices to be
connected to form an extended “total application”.
8.1 Software drivers
Software drivers are provided for easy configuration and use of the TDA19978B. These
drivers can be integrated with a large range of processors, with or without an operating
system. They control activity detection, input selection, video mode identification, color
conversion, Power-down modes and InfoFrame notification.
8.2 HDMI inputs
Control of the four HDMI inputs can be automatic using activity detection or using the
I2C-bus. The HDMI receiver inputs are defined by pins RXx0+, RXx0−, RXx1+, RXx1−,
RXx2+, RXx2−, RXxC+, RXxC−, RRX1, RRX2, HSCLx and HSDAx (x equals A, B, C or D
as applicable).
8.3 Termination resistance control
The HDMI receiver input contains a termination resistance control set by an external
resistor connected between pins RRXx and VDDH(3V3) (x equals 1 for inputs A and B or 2
for inputs C and D). Typically, the characteristic impedance is 50 Ω and the default value
of the external terminal control resistor is 12 kΩ ± 1 %.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
9 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
8.4 Equalizer
The auto-adaptive equalizer automatically measures and selects the settings which
provide the best signal quality for each cable. This improves signal quality and enables
the use of cable lengths up to 25 m (laboratory tested, contact NXP semiconductors for
detailed information). The equalizer is fully automatic and consequently does not need
any external control.
8.5 Activity detection
The TDA19978B uses activity detection to automatically select the active HDMI input. An
internal, fully programmable, frequency filter controls activity detection. It sees only the
activity on the HDMI inputs with a frequency range between the minimal frequency
(22.5 MHz) and the maximal frequency (205 MHz).
This activity detection can generate an interrupt enabling users to manage each HDMI
input.
8.6 Color depth unpacking
In Deep Color mode, the TDA19978B receives several fragments of a pixel group at the
HDMI link frequency. The color depth unpacking block translates the received pixel group
into pixels at the pixel frequency. This operation is fully automatic and does not need any
external control.
8.7 Derepeater
The HDMI source uses pixel repetition to increase the transmitted pixel clock frequency
for transmitting video formats at native pixel rates below 25 Mpixel/s or to increase the
number of audio sample packets in each line. The derepeater function discards repeated
pixels and divides the clock to reproduce the native video format.
8.8 Upsample
The HDMI source can use YCbCr 4:2:2 pixel encoding which enables the number of bits
allocated per component to be increased up to 12. The upsample function transforms this
12-bit YCbCr 4:2:2 data stream into a 12-bit YCbCr 4:4:4 data stream by repeating or
linearly interpolating the chrominance pixels Cb and Cr.
Upsampling mode is selected using the I2C-bus.
8.9 Packet extraction
Information sent during the Data Island periods is extracted from the HDMI data stream.
Audio clock regeneration, general control and InfoFrames can be read using the I2C-bus
while audio samples are sent to the audio FIFO.
The TDA19978B can receive HDMI 1.3a packets, general control and color gamut
metadata packets.
In audio applications, the TDA19978B manages HBR packets for high bit rate
compressed audio streams (IEC 61937), OBA samples and DST packets for one bit audio
and SACD with DSD and DST audio streams.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
10 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
The TDA19978B includes a two-channel status decoder supporting multi-channel
reception for audio sample packets. This enables the user to obtain channel status
information from the IEC 60958/IEC 61937 stream such as:
• The audio stream type (non-linear as IEC 61937 or L-PCM as IEC 60958)
• Copyright protection
• Sampling frequency
Refer to IEC 60958/IEC 61937 specifications for more details.
An update of each InfoFrame or the channel status content is indicated by a register bit
and the HIGH-to-LOW transition on output pin VAI. This makes CPU polling unnecessary.
8.10 Audio PLL
The TDA19978B generates a 128/256/512 × fs system clock enabling the use of simple
audio DACs without an integrated PLL, such as the UDA1334BTS. The programming of
the audio PLL can be either automatic, using the audio clock regeneration parameters
found in the Data Islands or set manually using the I2C-bus.
All standard audio sampling frequencies 32 kHz, 44.1 kHz, 88.2 kHz, 176.4 kHz, 48 kHz,
96 kHz and 192 kHz are accepted by the device.
8.11 Audio formatter
Audio samples can be output in either S/PDIF, I2S-bus formats or DSD (SACD). In I2S-bus
or S/PDIF modes, up to eight audio channels can be controlled using the audio port pins
(AP0 to AP5). In DSD mode (SACD), up to six audio channels can be controlled using
these pins. The audio port mapping depends on the channel allocation (see Table 4,
Table 5 and Table 6 for detailed information).
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
11 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 4.
Audio port configuration (Layout 0)
All audio ports are LV-TTL compatible.
Audio port
Pin
Layout 0
I2S-bus
S/PDIF
AP5
85
SYSCLK[1]
SYSCLK[1]
AP4
83
WS (word select)
WS[1]
AP3
82
AP2
81
AP1
80
AP0
79
ACLK
OBA
DSD channel 1
SD
78
SCK
S/PDIF
(I2S-bus
clock)
master clock for
64 × fs
DSD channel 0
S/PDIF[1]
DSD clock
64 × fs
64 × fs
32 × fs
[1]
Can be activated with the I2C-bus (optional).
Table 5.
Audio port configuration (Layout 1)
All audio ports are LV-TTL compatible.
Audio port
Pin
Layout 1
I2S-bus
S/PDIF
OBA
SYSCLK[1]
DSD channel 5
AP5
85
SYSCLK[1]
AP4
83
WS (word select)
WS[1]
DSD channel 4
AP3
82
SD3
S/PDIF3
DSD channel 3
AP2
81
SD2
S/PDIF2
DSD channel 2
AP1
80
SD1
S/PDIF1
DSD channel 1
AP0
79
SD0
S/PDIF0
ACLK
78
SCK
(I2S-bus
clock)
master clock for
64 × fs
DSD channel 0
S/PDIF[1]
64 × fs
DSD clock
64 × fs
32 × fs
[1]
Can be activated with the I2C-bus (optional).
Table 6.
Audio port configuration for HBR and DST packets
All audio ports are LV-TTL compatible.
Audio port
Pin
HBR demultiplexed
DST
I2S-bus
S/PDIF
SYSCLK[1]
AP5
85
SYSCLK[1]
AP4
83
WS (word select)
WS[1]
AP3
82
SDx + 3
S/PDIFx + 3
AP2
81
SDx + 2
S/PDIFx + 2
AP1
80
SDx + 1
S/PDIFx + 1
AP0
79
SDx
S/PDIFx
DSD channel 0
ACLK
78
SCK (I2S-bus clock)
master clock for S/PDIF[1]
DSD clock
64 × fs (ACR)
64 × fs
32 × fs (ACR)
[1]
TDA19978B_2
Product data sheet
frame_start
64 × fs
128 × fs
Can be activated with the I2C-bus (optional).
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
12 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
8.12 Sync timing measurement
To assist input format recognition, the vertical/horizontal periods and the horizontal pulse
width are measured based on the externally generated MCLK frequency (27 MHz crystal).
This function has an accuracy of 1 LSB = 1 × MCLK period.
8.13 Format measurement timing
The TDA19978B includes an improved system for accurate recognition of PC and TV
formats. This system measures the parameters of blanking and video active area.
This function can be useful for example when the TDA19978B receives PC format data in
HDMI or DVI modes.
8.14 Color space conversion
The color space conversion enables an RGB signal from the HDMI input to be converted
into a YCbCr signal or converting the YCbCr signal from the HDMI input into an RGB
signal. The color space conversion formula is:
C 11 C 12 C 13 ⎛ CY
OO1
YG
O11 ⎞⎟
⎜
=
+
×
+
⎜
⎟
C 21 C 22 C 23
OO2
VR
RV
O12
⎜
⎟
OO3
UB
BU
O13
C 31 C 32 C 33 ⎝
⎠
(1)
Activation of the color space conversion function and programming of all coefficients and
offsets is done via the I2C-bus.
8.15 4:2:2 downsampling filters
These filters downsample the Cb and Cr signals by a factor of 2. A delay has been added
to the G/Y channel corresponding to the downsample filters pipeline delay to make sure
the Y channel is in phase with the Cb and Cr channels.
Four different filters, from simple cut to ITU-R BT.601 compliant digital, can be selected
using the I2C-bus.
8.16 Range control
The range control function truncates the range of data to remove super-white and
super-black pixels at specified ceiling and floor values.
8.17 Dithering function
The error dispersal rounding (dithering) function can convert the color depth from 30-bit or
36-bit to reduced 30-bit or 24-bit color depth. When dithering is triggered, the TDA19978B
applies round, truncate or noise-shaping algorithms.
When the error dispersal rounding function is not used, the data coming from the filter is
directly sent to the 4:2:2 formatter. The error dispersal rounding function works only with
the active video signal.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
13 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
8.18 4:2:2 formatter
The 4:2:2 formatter contains the YCbCr 4:2:2 semi-planar and the YCbCr 4:2:2
ITU-R BT.656 formatting functions. The selection of these functions is made using the
I2C-bus.
• In YCbCr 4:2:2 mode: the data frequency of the Y signal is equal to the pixel clock
frequency. While the data frequency of the Cb and Cr signals is equal to half the pixel
clock frequency
• In semi-planar mode: the output clock frequency should be the same as the pixel
clock frequency
• In ITU-R BT.656 mode: the data frequency should be the same as the formatter clock
frequency (e.g. pixel clock frequency × 2)
The Start Active Video (SAV) and End Active Video (EAV) timing reference codes can be
included in the data stream based on the HREF, VREF and FREF positions from the
VHREF timing generator.
Specific codes programmed using the I2C-bus can replace the data stream during the
blanking period to mask gain and clamp calibration.
8.19 Video port selection
Each channel can be allocated to a specified video port using the I2C-bus (see Section 13
“Output video port formats (mapping examples)” on page 20) to optimize board layout at
the interface with video processing ICs. For example:
•
•
•
•
R, G or B in RGB 4:4:4 mode on pins VP[29:20]
Y, Cb or Cr in YUV 4:4:4 mode on pins VP[19:10]
Y or Cb-Cr in 4:2:2 semi-planar mode on pins VP[9:0]
Cb-Y-Cr-Y in 4:2:2 ITU-R BT.656 mode on pins VP[9:0]
Each video port can be set to high-impedance using the I2C-bus.
8.20 Output buffers
The output buffers are LV-TTL compatible. The outputs can be switched between active
and high-impedance by the I2C-bus.
The outputs HREF, VREF and FREF can be set to high-impedance (Z) or forced LOW (L),
independently of the timing reference codes.
8.21 VHREF timing generator
The VHREF timing generator outputs all of the timing signals used by the device:
• VREF, HREF and FREF signals for SAV, EAV and active video area definition
• VS and HS to change width and position compared with the HDMI inputs
8.22 I2C-bus serial interface
The I2C-bus serial interface enables the internal registers of the device to be
programmed. The slave address of the device is selected by pin A0.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
14 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
8.23 Power management
The TDA19978B can use one of three Power-down modes:
• level 0: full Power-down mode
• level 1: internal EDID memory with I2C-bus serial interface active
• level 2: internal EDID memory with I2C-bus serial interface and activity detection
enabled
The user can activate each mode with pin PD or using I2C-bus registers:
• level 0: PD pin is HIGH
• level 1: settings defined in the I2C-bus registers
• level 2: settings defined in the I2C-bus registers
8.24 EDID memory management
The TDA19978B embedded EDID memory can be shared with all HDMI inputs. The
embedded EDID memory shares 253 bytes with the four HDMI inputs. In addition, three
bytes are dedicated to the physical address and checksum for each HDMI input (see
Figure 3). This memory is accessible in parallel by all HDMI inputs. You can share the
EDID memory over zero, one, two, three or four HDMI input(s) as shown in Figure 4.
The content of embedded volatile EDID memory must be programmed using the I2C-bus
for each power-on of TDA19978B. The embedded EDID memory remains accessible on
each HDMI input when the TDA19978B uses a different low-power mode.
The “physical address” of each HDMI input can be easily changed with the TDA19978B
without corrupting the integrity of each DDC-bus.
8.24.1 EDID memory shared over all four HDMI inputs
EDID: 253 B
I2C-bus
TDA19978B
3B
3B
3B
3B
HDMI
INPUT
HDMI
INPUT
HDMI
INPUT
HDMI
INPUT
CPU
FLASH(1)
EDID CONTENT
001aai417
(1) 253 bytes
+ 3 bytes input A
+ 3 bytes input B
+ 3 bytes input C
+ 3 bytes input D
+ 1 byte address pointer (subPhys@): this indicates the address in each block where the data for
inputs A, B, C and D will be copied.
Fig 3.
TDA19978B_2
Product data sheet
An example of an application with EDID memory shared over all four HDMI inputs
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
15 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
8.24.2 EDID memory shared over three HDMI inputs
EDID: 253 B
I2C-bus
TDA19978B
3B
3B
3B
HDMI
INPUT
HDMI
INPUT
HDMI
INPUT
CPU
EXTERNAL EDID:
256 B or 512 B
DVI or
HDMI
INPUT
FLASH(1)
EDID CONTENT
001aai418
(1) 253 bytes
+ 3 bytes input B
+ 3 bytes input C
+ 3 bytes input D
+ 1 byte address pointer (subPhys@): this indicates the address in each block where the data for
inputs B, C and D will be copied.
Fig 4.
An example of an application with EDID shared over three HDMI inputs
9. I2C-bus protocol
The TDA19978B is a slave I2C-bus device and the SCL pin is only an input pin. The timing
and protocol for I2C-bus are standard.
Bit A0 of the I2C-bus device address is externally selected by the A0 pin. The main device
I2C-bus address is given in Table 7.
Table 7.
I2C-bus slave address
A6
A5
A4
A3
A2
A1
A0
R/W
1
0
0
1
1
0
A0
0/1
10. Limiting values
Table 8.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
TDA19978B_2
Product data sheet
Symbol
Parameter
VDDx(3V3)
VDDx(1V8)
Conditions
Min
Max
Unit
supply voltage on all 3.3 V pins
−0.5
+4.6
V
supply voltage on all 1.8 V pins
−0.5
+2.5
V
ΔVDD
supply voltage difference
−0.5
+0.5
V
IO
output current
-
35
mA
Tstg
storage temperature
−55
+150
°C
Tamb
ambient temperature
0
70
°C
Tj
junction temperature
-
125
°C
VESD
electrostatic discharge voltage
−2000
+2000
V
HBM
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
16 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
11. Thermal characteristics
Table 9.
Thermal characteristics
Symbol
Parameter
Rth(j-a)
Rth(j-c)
Conditions
Typ
Unit
thermal resistance from junction to ambient in free air
22.8
K/W
thermal resistance from junction to case
11.1
K/W
12. Characteristics
Table 10. Characteristics
Tamb = 0 °C to 70 °C; typical values measured at Tamb = 25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
3.465
V
Supplies
VDDH(3V3)
HDMI supply voltage (3.3 V)
VDDH(1V8)
HDMI supply voltage (1.8 V)
1.71
1.89
V
VDDI(3V3)
input supply voltage (3.3 V)
3.135 3.3
3.465
V
VDDC(1V8)
core supply voltage (1.8 V)
1.71
1.89
V
VDDO(3V3)
output supply voltage (3.3 V)
IDDH(3V3)
IDDH(1V8)
IDDI(3V3)
IDDO(3V3)
IDDC(1V8)
HDMI supply current (3.3 V)
HDMI supply current (1.8 V)
input supply current (3.3 V)
output supply current (3.3 V)
core supply current (1.8 V)
3.135 3.3
1.8
1.8
3.135 3.3
3.465
V
720p at 60 Hz
[1]
-
103
-
mA
1080p at 60 Hz
[1]
-
106
-
mA
1080p at 60 Hz; Deep Color mode
[1]
-
110
-
mA
720p at 60 Hz
[1]
-
48
-
mA
1080p at 60 Hz
[1]
-
68
-
mA
1080p at 60 Hz; Deep Color mode
[1]
-
85
-
mA
720p at 60 Hz
[1]
-
1
-
mA
1080p at 60 Hz
[1]
-
1
-
mA
1080p at 60 Hz; Deep Color mode
[1]
-
1
-
mA
720p at 60 Hz
[1]
-
49
-
mA
1080p at 60 Hz
[1]
-
78
-
mA
1080p at 60 Hz; Deep Color mode
[1]
-
120
-
mA
720p at 60 Hz
[1]
-
148
-
mA
1080p at 60 Hz
[1]
-
283
-
mA
1080p at 60 Hz; Deep Color mode
[1]
-
453
-
mA
ΔVDD(3V3-3V3) supply voltage difference
between two 3.3 V supplies
start-up and established conditions
−100
-
+100
mV
ΔVDD(1V8-1V8) supply voltage difference
between two 1.8 V supplies
start-up and established conditions
−100
-
+100
mV
P
Active mode
power dissipation
TDA19978B_2
Product data sheet
[1]
720p at 60 Hz
-
0.75
-
W
1080p at 60 Hz
-
1.13
-
W
1080p at 60 Hz;
Deep Color mode
-
1.63
-
W
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
17 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 10. Characteristics …continued
Tamb = 0 °C to 70 °C; typical values measured at Tamb = 25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Pcons
power consumption
Power-down mode
pin PD = HIGH
-
1
-
mW
I2C-bus;
-
4
-
mW
-
150
-
mW
pin VCLK
165
-
-
MHz
pin ACLK
25
-
-
MHz
pin SYSCLK
50
-
-
MHz
pin VCLK
-
50
-
%
pin ACLK
-
50
-
%
pin SYSCLK
-
50
-
%
EDID
I2C-bus; EDID; activity detection
Clock timing output: pins VCLK, ACLK and SYSCLK
fclk(max)
δclk
maximum clock frequency
clock duty cycle
Timing output: pins VP[29:0]; fs = 165 MHz; CL = 10 pF; see Figure 5
tsu(Q)
data output set-up time
0.40
-
1.50
ns
th(Q)
data output hold time
0.80
-
2.00
ns
td(pipe)
pipeline delay time
-
80 × Tclk
-
clock intervals from inputs to
outputs; all modes
Timing output: pins AP[5:0] with respect to pin ACLK; fclk = 12.288 MHz; CL = 10 pF; see Figure 6
tsu(Q)
data output set-up time
69
-
-
ns
th(Q)
data output hold time
2
-
-
ns
LV-TTL digital outputs: pins VP[29:0], VCLK, AP[5:0], ACLK, DE, HS, VS, HREF, VREF, FREF; CL = 10 pF
VOL
LOW-level output voltage
IOL = 2 mA
VOH
HIGH-level output voltage
IOH = −2 mA
ILOZ
OFF-state output leakage current high-impedance state; VO = 0 V
VO = VDDO(3V3) × 1⁄3
VO = VDDO(3V3) ×
2⁄
3
VO = VDDO(3V3)
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
[2]
-
-
0.4
V
2.4
-
-
V
-
0
-
μA
10
-
100
μA
−100
-
−10
μA
-
0
-
μA
© NXP B.V. 2010. All rights reserved.
18 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 10. Characteristics …continued
Tamb = 0 °C to 70 °C; typical values measured at Tamb = 25 °C; unless otherwise specified.
Symbol
Parameter
Digital inputs: pins RXxC+,
Conditions
Min
Typ
Max
Unit
RRRX1 = 12 kΩ ± 1 %;
RRRX2 = 12 kΩ ± 1 %
150
-
1200
mV
2.735 -
3.475
V
205
-
-
MHz
150
-
1200
mV
2.735 -
3.475
V
RXxC−[3]
VI(dif)
differential input voltage
VI(cm)
common-mode input voltage
fclk(max)
maximum clock frequency
Digital inputs: pins RXx0+, RXx0−, RXx1+, RXx1−, RXx2+,
RRRX1 = 12 kΩ ± 1 %;
RRRX2 = 12 kΩ ± 1 %
VI(dif)
differential input voltage
VI(cm)
common-mode input voltage
I2C-bus:
pins SCL and
RXx2−[3]
SDA[4]
fSCL
SCL clock frequency
-
-
400
kHz
Cb
capacitive load for each bus line
-
-
400
pF
capacitance for each I/O pin
-
-
10
pF
Standard-mode
-
-
100
kHz
Fast-mode
-
-
400
kHz
-
-
10
pF
Ci
DDC
I2C-bus:
fSCL
pins HSCLx, HSDAx
[3][5]
SCL clock frequency
capacitance for each I/O pin
Ci
[1]
At 30 % activity on video port output.
[2]
In high-impedance state, the output buffer is set to repeater mode recopying the input logic state with a small current. The output current
changes from most negative to the most positive value at the triggering level which is internally set to VDDO(3V3) / 2 (e.g. the value of a
pull-up or pull-down resistor must be lower than 18 kΩ to have a stable output value of VDDO(3V3) or 0 V).
[3]
x = A, B, C or D.
[4]
Fast-mode, 5 V tolerant.
[5]
5 V tolerant.
VCLK
50 %
tsu(Q)
2.4 V
VP[29:0]
0.4 V
th(Q)
Fig 5.
001aah368
Output timing diagram pin VCLK and pins VP[29:0]
ACLK
50 %
tsu(Q)
2.4 V
AP[5:0]
0.4 V
th(Q)
Fig 6.
TDA19978B_2
Product data sheet
001aah369
Output timing diagram pin ACLK and pins AP[5:0]
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
19 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
13. Output video port formats (mapping examples)
The following tables show examples of possible output formats that are enabled by the
video port swap function in the driver.
Table 11.
Output in 12-bit video port format (mapping example 1)
Signal
YCbCr 4:2:2 semi-planar[1]
YCbCr 4:2:2 ITU-R BT.656[1]
VP[29]
Y0[11]
Y1[11]
Z/L
Z/L
Z/L
Z/L
VP[28]
Y0[10]
Y1[10]
Z/L
Z/L
Z/L
Z/L
VP[27]
Y0[9]
Y1[9]
Z/L
Z/L
Z/L
Z/L
VP[26]
Y0[8]
Y1[8]
Z/L
Z/L
Z/L
Z/L
VP[25]
Y0[7]
Y1[7]
Z/L
Z/L
Z/L
Z/L
VP[24]
Y0[6]
Y1[6]
Z/L
Z/L
Z/L
Z/L
VP[23]
Y0[5]
Y1[5]
Z/L
Z/L
Z/L
Z/L
VP[22]
Y0[4]
Y1[4]
Z/L
Z/L
Z/L
Z/L
VP[21]
Y0[3]
Y1[3]
Z/L
Z/L
Z/L
Z/L
VP[20]
Y0[2]
Y1[2]
Z/L
Z/L
Z/L
Z/L
VP[19]
Y0[1]
Y1[1]
Z/L
Z/L
Z/L
Z/L
VP[18]
Y0[0]
Y1[0]
Z/L
Z/L
Z/L
Z/L
VP[17]
Cb[11]
Cr[11]
Cb[11]
Y0[11]
Cr[11]
Y1[11]
VP[16]
Cb[10]
Cr[10]
Cb[10]
Y0[10]
Cr[10]
Y1[10]
VP[15]
Cb[9]
Cr[9]
Cb[9]
Y0[9]
Cr[9]
Y1[9]
VP[14]
Cb[8]
Cr[8]
Cb[8]
Y0[8]
Cr[8]
Y1[8]
VP[13]
Cb[7]
Cr[7]
Cb[7]
Y0[7]
Cr[7]
Y1[7]
VP[12]
Cb[6]
Cr[6]
Cb[6]
Y0[6]
Cr[6]
Y1[6]
VP[11]
Cb[5]
Cr[5]
Cb[5]
Y0[5]
Cr[5]
Y1[5]
VP[10]
Cb[4]
Cr[4]
Cb[4]
Y0[4]
Cr[4]
Y1[4]
VP[9]
Cb[3]
Cr[3]
Cb[3]
Y0[3]
Cr[3]
Y1[3]
VP[8]
Cb[2]
Cr[2]
Cb[2]
Y0[2]
Cr[2]
Y1[2]
VP[7]
Cb[1]
Cr[1]
Cb[1]
Y0[1]
Cr[1]
Y1[1]
VP[6]
Cb[0]
Cr[0]
Cb[0]
Y0[0]
Cr[0]
Y1[0]
VP[5]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[4]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[3]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[2]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[1]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[0]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
[1]
Z = high-impedance; L = LOW-level; depending on the driver configuration.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
20 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 12.
Output in 12-bit video port format (mapping example 2)
Signal
YCbCr 4:2:2 semi-planar[1]
YCbCr 4:2:2 ITU-R BT.656[1]
VP[29]
Cb[11]
Cr[11]
Cb[11]
Y0[11]
Cr[11]
Y1[11]
VP[28]
Cb[10]
Cr[10]
Cb[10]
Y0[10]
Cr[10]
Y1[10]
VP[27]
Cb[9]
Cr[9]
Cb[9]
Y0[9]
Cr[9]
Y1[9]
VP[26]
Cb[8]
Cr[8]
Cb[8]
Y0[8]
Cr[8]
Y1[8]
VP[25]
Cb[7]
Cr[7]
Cb[7]
Y0[7]
Cr[7]
Y1[7]
VP[24]
Cb[6]
Cr[6]
Cb[6]
Y0[6]
Cr[6]
Y1[6]
VP[23]
Cb[5]
Cr[5]
Cb[5]
Y0[5]
Cr[5]
Y1[5]
VP[22]
Cb[4]
Cr[4]
Cb[4]
Y0[4]
Cr[4]
Y1[4]
VP[21]
Cb[3]
Cr[3]
Cb[3]
Y0[3]
Cr[3]
Y1[3]
VP[20]
Cb[2]
Cr[2]
Cb[2]
Y0[2]
Cr[2]
Y1[2]
VP[19]
Cb[1]
Cr[1]
Cb[1]
Y0[1]
Cr[1]
Y1[1]
VP[18]
Cb[0]
Cr[0]
Cb[0]
Y0[0]
Cr[0]
Y1[0]
VP[17]
Y0[11]
Y1[11]
Z/L
Z/L
Z/L
Z/L
VP[16]
Y0[10]
Y1[10]
Z/L
Z/L
Z/L
Z/L
VP[15]
Y0[9]
Y1[9]
Z/L
Z/L
Z/L
Z/L
VP[14]
Y0[8]
Y1[8]
Z/L
Z/L
Z/L
Z/L
VP[13]
Y0[7]
Y1[7]
Z/L
Z/L
Z/L
Z/L
VP[12]
Y0[6]
Y1[6]
Z/L
Z/L
Z/L
Z/L
VP[11]
Y0[5]
Y1[5]
Z/L
Z/L
Z/L
Z/L
VP[10]
Y0[4]
Y1[4]
Z/L
Z/L
Z/L
Z/L
VP[9]
Y0[3]
Y1[3]
Z/L
Z/L
Z/L
Z/L
VP[8]
Y0[2]
Y1[2]
Z/L
Z/L
Z/L
Z/L
VP[7]
Y0[1]
Y1[1]
Z/L
Z/L
Z/L
Z/L
VP[6]
Y0[0]
Y1[0]
Z/L
Z/L
Z/L
Z/L
VP[5]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[4]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[3]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[2]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[1]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[0]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
[1]
Z = high-impedance; L = LOW-level; depending on the driver configuration.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
21 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 13.
Output in 10-bit video port format (mapping example 1)
Signal
RGB
YCbCr 4:4:4
YCbCr 4:2:2 semi-planar[1]
YCbCr 4:2:2 ITU-R BT.656[1]
VP[29]
G[11]
Y[11]
Y0[11]
Y1[11]
Z/L
Z/L
Z/L
Z/L
VP[28]
G[10]
Y[10]
Y0[10]
Y1[10]
Z/L
Z/L
Z/L
Z/L
VP[27]
G[9]
Y[9]
Y0[9]
Y1[9]
Z/L
Z/L
Z/L
Z/L
VP[26]
G[8]
Y[8]
Y0[8]
Y1[8]
Z/L
Z/L
Z/L
Z/L
VP[25]
G[7]
Y[7]
Y0[7]
Y1[7]
Z/L
Z/L
Z/L
Z/L
VP[24]
G[6]
Y[6]
Y0[6]
Y1[6]
Z/L
Z/L
Z/L
Z/L
VP[23]
G[5]
Y[5]
Y0[5]
Y1[5]
Z/L
Z/L
Z/L
Z/L
VP[22]
G[4]
Y[4]
Y0[4]
Y1[4]
Z/L
Z/L
Z/L
Z/L
VP[21]
G[3]
Y[3]
Y0[3]
Y1[3]
Z/L
Z/L
Z/L
Z/L
VP[20]
G[2]
Y[2]
Y0[2]
Y1[2]
Z/L
Z/L
Z/L
Z/L
VP[19]
R[11]
Cr[11]
Cb[11]
Cr[11]
Cb[11]
Y0[11]
Cr[11]
Y1[11]
VP[18]
R[10]
Cr[10]
Cb[10]
Cr[10]
Cb[10]
Y0[10]
Cr[10]
Y1[10]
VP[17]
R[9]
Cr[9]
Cb[9]
Cr[9]
Cb[9]
Y0[9]
Cr[9]
Y1[9]
VP[16]
R[8]
Cr[8]
Cb[8]
Cr[8]
Cb[8]
Y0[8]
Cr[8]
Y1[8]
VP[15]
R[7]
Cr[7]
Cb[7]
Cr[7]
Cb[7]
Y0[7]
Cr[7]
Y1[7]
VP[14]
R[6]
Cr[6]
Cb[6]
Cr[6]
Cb[6]
Y0[6]
Cr[6]
Y1[6]
VP[13]
R[5]
Cr[5]
Cb[5]
Cr[5]
Cb[5]
Y0[5]
Cr[5]
Y1[5]
VP[12]
R[4]
Cr[4]
Cb[4]
Cr[4]
Cb[4]
Y0[4]
Cr[4]
Y1[4]
VP[11]
R[3]
Cr[3]
Cb[3]
Cr[3]
Cb[3]
Y0[3]
Cr[3]
Y1[3]
VP[10]
R[2]
Cr[2]
Cb[2]
Cr[2]
Cb[2]
Y0[2]
Cr[2]
Y1[2]
VP[9]
B[11]
Cb[11]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[8]
B[10]
Cb[10]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[7]
B[9]
Cb[9]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[6]
B[8]
Cb[8]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[5]
B[7]
Cb[7]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[4]
B[6]
Cb[6]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[3]
B[5]
Cb[5]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[2]
B[4]
Cb[4]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[1]
B[3]
Cb[3]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[0]
B[2]
Cb[2]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
[1]
Z = high-impedance; L = LOW-level; depending on the driver configuration.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
22 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 14.
Output in 10-bit video port format (mapping example 2)
Signal
RGB
YCbCr 4:4:4
YCbCr 4:2:2 semi-planar[1]
YCbCr 4:2:2 ITU-R BT.656[1]
VP[29]
B[11]
Cb[11]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[28]
B[10]
Cb[10]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[27]
B[9]
Cb[9]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[26]
B[8]
Cb[8]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[25]
B[7]
Cb[7]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[24]
B[6]
Cb[6]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[23]
B[5]
Cb[5]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[22]
B[4]
Cb[4]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[21]
B[3]
Cb[3]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[20]
B[2]
Cb[2]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[19]
G[11]
Y[11]
Y0[11]
Y1[11]
Z/L
Z/L
Z/L
Z/L
VP[18]
G[10]
Y[10]
Y0[10]
Y1[10]
Z/L
Z/L
Z/L
Z/L
VP[17]
G[9]
Y[9]
Y0[9]
Y1[9]
Z/L
Z/L
Z/L
Z/L
VP[16]
G[8]
Y[8]
Y0[8]
Y1[8]
Z/L
Z/L
Z/L
Z/L
VP[15]
G[7]
Y[7]
Y0[7]
Y1[7]
Z/L
Z/L
Z/L
Z/L
VP[14]
G[6]
Y[6]
Y0[6]
Y1[6]
Z/L
Z/L
Z/L
Z/L
VP[13]
G[5]
Y[5]
Y0[5]
Y1[5]
Z/L
Z/L
Z/L
Z/L
VP[12]
G[4]
Y[4]
Y0[4]
Y1[4]
Z/L
Z/L
Z/L
Z/L
VP[11]
G[3]
Y[3]
Y0[3]
Y1[3]
Z/L
Z/L
Z/L
Z/L
VP[10]
G[2]
Y[2]
Y0[2]
Y1[2]
Z/L
Z/L
Z/L
Z/L
VP[9]
R[11]
Cr[11]
Cb[11]
Cr[11]
Cb[11]
Y0[11]
Cr[11]
Y1[11]
VP[8]
R[10]
Cr[10]
Cb[10]
Cr[10]
Cb[10]
Y0[10]
Cr[10]
Y1[10]
VP[7]
R[9]
Cr[9]
Cb[9]
Cr[9]
Cb[9]
Y0[9]
Cr[9]
Y1[9]
VP[6]
R[8]
Cr[8]
Cb[8]
Cr[8]
Cb[8]
Y0[8]
Cr[8]
Y1[8]
VP[5]
R[7]
Cr[7]
Cb[7]
Cr[7]
Cb[7]
Y0[7]
Cr[7]
Y1[7]
VP[4]
R[6]
Cr[6]
Cb[6]
Cr[6]
Cb[6]
Y0[6]
Cr[6]
Y1[6]
VP[3]
R[5]
Cr[5]
Cb[5]
Cr[5]
Cb[5]
Y0[5]
Cr[5]
Y1[5]
VP[2]
R[4]
Cr[4]
Cb[4]
Cr[4]
Cb[4]
Y0[4]
Cr[4]
Y1[4]
VP[1]
R[3]
Cr[3]
Cb[3]
Cr[3]
Cb[3]
Y0[3]
Cr[3]
Y1[3]
VP[0]
R[2]
Cr[2]
Cb[2]
Cr[2]
Cb[2]
Y0[2]
Cr[2]
Y1[2]
[1]
Z = high-impedance; L = LOW-level; depending on the driver configuration.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
23 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 15.
Output in 8-bit video port format (mapping example 1)
Signal
RGB
YCbCr 4:4:4[1]
YCbCr 4:2:2 semi-planar[1]
YCbCr 4:2:2 ITU-R BT.656[1]
VP[29]
G[11]
Y[11]
Y0[11]
Y1[11]
Z/L
Z/L
Z/L
Z/L
VP[28]
G[10]
Y[10]
Y0[10]
Y1[10]
Z/L
Z/L
Z/L
Z/L
VP[27]
G[9]
Y[9]
Y0[9]
Y1[9]
Z/L
Z/L
Z/L
Z/L
VP[26]
G[8]
Y[8]
Y0[8]
Y1[8]
Z/L
Z/L
Z/L
Z/L
VP[25]
G[7]
Y[7]
Y0[7]
Y1[7]
Z/L
Z/L
Z/L
Z/L
VP[24]
G[6]
Y[6]
Y0[6]
Y1[6]
Z/L
Z/L
Z/L
Z/L
VP[23]
G[5]
Y[5]
Y0[5]
Y1[5]
Z/L
Z/L
Z/L
Z/L
VP[22]
G[4]
Y[4]
Y0[4]
Y1[4]
Z/L
Z/L
Z/L
Z/L
VP[21]
R[11]
Cr[11]
Cb[11]
Cr[11]
Cb[11]
Y0[11]
Cr[11]
Y1[11]
VP[20]
R[10]
Cr[10]
Cb[10]
Cr[10]
Cb[10]
Y0[10]
Cr[10]
Y1[10]
VP[19]
R[9]
Cr[9]
Cb[9]
Cr[9]
Cb[9]
Y0[9]
Cr[9]
Y1[9]
VP[18]
R[8]
Cr[8]
Cb[8]
Cr[8]
Cb[8]
Y0[8]
Cr[8]
Y1[8]
VP[17]
R[7]
Cr[7]
Cb[7]
Cr[7]
Cb[7]
Y0[7]
Cr[7]
Y1[7]
VP[16]
R[6]
Cr[6]
Cb[6]
Cr[6]
Cb[6]
Y0[6]
Cr[6]
Y1[6]
VP[15]
R[5]
Cr[5]
Cb[5]
Cr[5]
Cb[5]
Y0[5]
Cr[5]
Y1[5]
VP[14]
R[4]
Cr[4]
Cb[4]
Cr[4]
Cb[4]
Y0[4]
Cr[4]
Y1[4]
VP[13]
B[11]
Cb[11]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[12]
B[10]
Cb[10]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[11]
B[9]
Cb[9]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[10]
B[8]
Cb[8]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[9]
B[7]
Cb[7]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[8]
B[6]
Cb[6]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[7]
B[5]
Cb[5]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[6]
B[4]
Cb[4]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[5]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[4]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[3]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[2]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[1]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[0]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
[1]
Z = high-impedance; L = LOW-level; depending on the driver configuration.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
24 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 16.
Output in 8-bit video port format (mapping example 2)
Signal
RGB[1] YCbCr 4:4:4[1]
YCbCr 4:2:2 semi-planar[1]
YCbCr 4:2:2 ITU-R BT.656[1]
VP[29]
B[11]
Cb[11]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[28]
B[10]
Cb[10]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[27]
B[9]
Cb[9]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[26]
B[8]
Cb[8]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[25]
B[7]
Cb[7]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[24]
B[6]
Cb[6]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[23]
B[5]
Cb[5]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[22]
B[4]
Cb[4]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[21]
G[11]
Y[11]
Y0[11]
Y1[11]
Z/L
Z/L
Z/L
Z/L
VP[20]
G[10]
Y[10]
Y0[10]
Y1[10]
Z/L
Z/L
Z/L
Z/L
VP[19]
G[9]
Y[9]
Y0[9]
Y1[9]
Z/L
Z/L
Z/L
Z/L
VP[18]
G[8]
Y[8]
Y0[8]
Y1[8]
Z/L
Z/L
Z/L
Z/L
VP[17]
G[7]
Y[7]
Y0[7]
Y1[7]
Z/L
Z/L
Z/L
Z/L
VP[16]
G[6]
Y[6]
Y0[6]
Y1[6]
Z/L
Z/L
Z/L
Z/L
VP[15]
G[5]
Y[5]
Y0[5]
Y1[5]
Z/L
Z/L
Z/L
Z/L
VP[14]
G[4]
Y[4]
Y0[4]
Y1[4]
Z/L
Z/L
Z/L
Z/L
VP[13]
R[11]
Cr[11]
Cb[11]
Cr[11]
Cb[11]
Y0[11]
Cr[11]
Y1[11]
VP[12]
R[10]
Cr[10]
Cb[10]
Cr[10]
Cb[10]
Y0[10]
Cr[10]
Y1[10]
VP[11]
R[9]
Cr[9]
Cb[9]
Cr[9]
Cb[9]
Y0[9]
Cr[9]
Y1[9]
VP[10]
R[8]
Cr[8]
Cb[8]
Cr[8]
Cb[8]
Y0[8]
Cr[8]
Y1[8]
VP[9]
R[7]
Cr[7]
Cb[7]
Cr[7]
Cb[7]
Y0[7]
Cr[7]
Y1[7]
VP[8]
R[6]
Cr[6]
Cb[6]
Cr[6]
Cb[6]
Y0[6]
Cr[6]
Y1[6]
VP[7]
R[5]
Cr[5]
Cb[5]
Cr[5]
Cb[5]
Y0[5]
Cr[5]
Y1[5]
VP[6]
R[4]
Cr[4]
Cb[4]
Cr[4]
Cb[4]
Y0[4]
Cr[4]
Y1[4]
VP[5]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[4]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[3]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[2]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[1]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
VP[0]
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
Z/L
[1]
Z = high-impedance; L = LOW-level; depending on the driver configuration.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
25 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
14. Example of supported video formats
Table 17.
Example of supported video formats
Standard
Format
Total pixels ×
total lines
Horizontal rate Pixel clock
(kHz)
rate (MHz)[1]
576i[2]
1440 × 576i 50 Hz
1728 × 625
15.750
27.000[3]
480i[4]
1440 × 480i 59.94 Hz
1716 × 525
15.734
27.000[3]
1440 × 480i 60 Hz
1716 × 525
15.750
27.027[3]
576p
720 × 576p 50 Hz
864 × 625
31.250
27.000
480p
720 × 480p 59.94 Hz
858 × 525
31.469
27.000
720 × 480p 60 Hz
858 × 525
31.500
27.027
720p
1280 × 720p 50 Hz
1980 × 750
37.500
74.250
1280 × 720p 59.94 Hz
1650 × 750
44.955
74.176
1280 × 720p 60 Hz
1650 × 750
45.000
74.250
1920 × 1080i 50 Hz
2640 × 1125
28.125
74.250
1920 × 1080i 59.94 Hz
2200 × 1125
33.716
74.176
1920 × 1080i 60 Hz
2200 × 1125
33.750
74.250
2640 × 1125
56.250
148.500
1080i
1080p
1920 × 1080p 50
Hz[5]
2200 × 1125
67.433
148.352
1920 × 1080p 60 Hz[5]
2200 × 1125
67.500
148.500
640 × 480p 60 Hz
800 × 525
31.469
25.175
640 × 480p 72 Hz
832 × 520
37.861
31.500
640 × 480p 75 Hz
840 × 500
37.500
31.500
640 × 480p 85 Hz
832 × 509
43.269
36.000
800 × 600p 56 Hz
1024 × 625
35.156
36.000
800 × 600p 60 Hz
1056 × 628
37.879
40.000
800 × 600p 72 Hz
1040 × 666
48.077
50.000
800 × 600p 75 Hz
1056 × 625
46.875
49.500
800 × 600p 85 Hz
1048 × 631
53.674
56.250
800 × 600p 120 Hz
960 × 636
76.302
73.250
1920 × 1080p 59.94
0.31M3 VGA
0.48M3 SVGA
0.48M3-R
0.41M9
848 × 480p 60 Hz
1088 × 517
31.020
33.750
0.79M3 XGA
1024 × 768p 43 Hz
1264 × 817
35.522
44.900
1024 × 768p 60 Hz
1344 × 806
48.363
65.000
1024 × 768p 70 Hz
1328 × 806
56.476
75.000
1024 × 768p 75 Hz
1312 × 800
60.023
78.750
1024 × 768p 85 Hz
1376 × 808
68.677
94.500
0.79M3-R XGA
1024 × 768p 120 Hz
1184 × 813
97.551
115.500
1.00M3
1152 × 864p 75 Hz
1600 × 900
67.500
108.000
0.98M9-R
1280 × 768p 60 Hz
1440 × 790
47.396
68.250
1280 × 768p 120 Hz[5]
1440 × 813
97.396
140.250
1280 × 768p 60 Hz
1664 × 798
47.776
79.500
1280 × 768p 75 Hz
1696 × 805
60.289
102.250
1280 × 768p 85 Hz
1712 × 809
68.633
117.500
0.98M9
TDA19978B_2
Product data sheet
Hz[5]
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
26 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 17.
Example of supported video formats …continued
Total pixels ×
total lines
Horizontal rate Pixel clock
(kHz)
rate (MHz)[1]
1280 × 800p 60 Hz
1440 × 823
49.306
71.000
1280 × 800p 120
1440 × 847
101.563
146.250
Standard
Format
1.02MA-R
1.02MA
1.23M3
1280 × 800p 60 Hz
1680 × 831
49.702
83.500
1280 × 800p 75 Hz
1696 × 838
62.795
106.500
1280 × 800p 85 Hz
1712 × 843
71.554
122.500
1280 × 960p 60 Hz
1800 × 1000
60.000
108.000
Hz[5]
1728 × 1011
85.938
148.500
1280 × 1024p 60 Hz
1688 × 1066
63.981
108.000
1280 × 1024p 75 Hz
1688 × 1066
79.976
135.000
1280 × 1024p 85
1728 × 1072
91.146
157.500
1280 × 960p 85
1.31M4 SXGA
Hz[5]
Hz[5]
1.04M9
1360 × 768p 60 Hz
1792 × 795
47.712
85.500
1.04M9-R
1360 × 768p 120 Hz[5]
1520 × 813
97.533
148.250
1.47M3-R
1400 × 1050p 60 Hz
1560 × 1080
64.744
101.000
1.47M3
1400 × 1050p 60 Hz
1864 × 1089
65.317
121.750
1896 × 1099
82.278
156.000
1.29MA-R
1440 × 900p 60 Hz
1600 × 926
55.469
88.750
1.29MA
1440 × 900p 60 Hz
1904 × 934
55.935
106.500
1440 × 900p 75
Hz[5]
1936 × 942
70.635
136.750
1440 × 900p 85
Hz[5]
1400 × 1050p 75
Hz[5]
1952 × 948
80.430
157.000
1.92M3 UXGA
1600 × 1200p 60 Hz[5]
2160 × 1250
75.000
162.000
1.76MA-R
1680 × 1050p 60 Hz
1840 × 1080
64.674
119.000
1.76MA
1680 × 1050p 60
Hz[5]
2240 × 1089
65.290
146.250
2.30MA-R[6]
1920 × 1200p 60
Hz[5]
2080 × 1235
74.038
154.000
[1]
Pixel clock rate corresponds to VCLK output for 4:4:4 format and 4:2:2 semi-planar; VCLK / 2 for 4:2:2
ITU-R BT.656 format. The pixel clock rate can be determined by:
a) Total pixels × total lines × frame rate for the progressive format.
b) Total pixels × total lines × frame rate / 2 for the interlaced format.
TDA19978B_2
Product data sheet
[2]
Also referred to as PAL (Phase Alternating Line).
[3]
Pixel-doubling.
[4]
Also referred to as NTSC (National Television Standards Committee).
[5]
Only supports Deep Color mode 10-bit.
[6]
Sometimes also referred to as WUXGA (Wide Ultra eXtended Graphics Array).
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
27 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
15. Application information
HDMI inputs A and B
143
71
70
69
68
67
66
65
audio port output
72
VP[27]
VP[26]
VP[25]
VP[24]
VP[23]
VP[22]
VSSO
64
control outputs and video port outputs
Fig 7.
VP[21]
VDDC(1V8)
1.8 VDIG
62
61
60
59
58
57
56
55
53
63
VDDO(3V3)
3.3 VDIG
VP[20]
VP[19]
VP[18]
VP[17]
VP[16]
VP[15]
VP[14]
VP[13]
VSSC
GNDC
54
36
27 MHz
I2C-bus DDC A and B
34
35
37
VP[0]
33
VSSO
DE
32
VP[12]
VS/VREF
HS/HREF
30
31
51
CS/FREF
29
52
VSSO
3.3 VDIG
VCLK
28
50
VDDO(3V3)
VDDO(3V3)
3.3 VDIG
26
27
49
1.8 VDIG
GNDC
VP[11]
VPP
VDDC(1V8)
24
25
48
RXC2−
RXC2+
22
23
VP[10]
VSSH
21
47
RXD2−
VP[9]
RXD2+
46
VDDH(3V3)
VP[8]
3.3 VHDMI
TDA19978BHV
20
45
RXC1+
18
19
VP[7]
RXC1−
16
17
44
VSSH
VP[6]
RXD1−
14
15
VP[5]
RXD1+
43
VDDH(1V8)
VP[4]
1.8 VHDMI
12
13
42
RXC0−
RXC0+
10
11
VSSO
HDMI inputs C and D
VSSH
1.8 VDIG
RXD0−
40
RXD0+
8
9
41
VDDH(3V3)
VDDC(1V8)
RXCC+
3.3 VHDMI
6
7
3.3 VDIG
RXCC−
4
5
39
VSSH
3
VP[3]
RXDC−
107
VDDO(3V3)
RXDC+
VDDH(1V8)
1.8 VHDMI
VDDC(1V8)
1.8 VDIG
RRX1 12 kΩ 1%
3.3 VHDMI
106
VSSH
105
VDDH(3V3)
3.3 VHDMI
104
TEST0 0 Ω
103
GNDC
HSCLB
102
HSDAB
101
HSCLA
100
HSDAA
99
SCL
98
SDA
97
VAI
96
VDDI(3V3)
3.3 VDIG_I
95
XTALIN/MCLK
94
XTALOUT
93
VDDC(1V8)
1.8 VDIG
92
VSSH
91
VDDH(1V8)
1.8 VHDMI
90
VSSH
89
VDDH(3V3)
3.3 VHDMI
88
VDDH(3V3)
3.3 VHDMI
87
VSSO
86
AP5/SYSCLK
85
VDDO(3V3)
3.3 VDIG
84
AP4/WS
83
AP3
82
AP2
81
AP1
80
AP0
79
ACLK
78
VSSO
77
VP[29]
76
VP[28]
75
VDDO(3V3)
3.3 VDIG
74
VSSC
73
GNDC
108
2
VP[2]
3.3 VHDMI
VDDH(3V3)
1
38
PD
VP[1]
VSSC
GNDC
144
VDDH(1V8)
1.8 VHDMI
RRX2 12 kΩ 1%
3.3 VHDMI
VDDI(3V3)
3.3 VDIG_I
142
HSCLD
141
HSDAD
140
HSCLC
139
HSDAC
138
VDDC(1V8)
1.8 VDIG
137
VDDC(1V8)
1.8 VDIG
136
VSSH
135
RXA2+
134
RXA2−
133
VSSH
132
RXB2−
131
RXB2+
130
VDDH(3V3)
3.3 VHDMI
129
RXA1+
128
RXA1−
127
VSSH
126
RXB1−
125
RXB1+
124
VDDH(1V8)
1.8 VHDMI
123
RXA0+
122
RXA0−
121
VSSH
120
RXB0−
119
RXB0+
118
VDDH(3V3)
3.3 VHDMI
117
RXAC+
116
RXAC−
115
VSSH
114
RXBC−
113
RXBC+
112
VDDH(3V3)
3.3 VHDMI
111
A0
110
VSSC
GNDC
109
DDC C and D
001aai419
Application diagram of TDA19978B
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
28 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
16. Package outline
HLQFP144: plastic thermal enhanced low profile quad flat package; 144 leads;
body 20 x 20 x 1.4 mm; exposed die pad
SOT612-3
c
y
exposed die pad
X
A
Dh
73
72
108
109
ZE
e
Eh
E HE
A A2
(A 3)
A1
θ
wM
Lp
bp
L
pin 1 index
detail X
37
144
1
36
v M A
ZD
wM
bp
e
D
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D(1)
Dh
E(1)
Eh
e
mm
1.6
0.12
0.05
1.45
1.35
0.25
0.27
0.17
0.20
0.09
20.1
19.9
5.7
5.5
20.1
19.9
5.7
5.5
0.5
HD
HE
22.15 22.15
21.85 21.85
L
Lp
v
w
y
1
0.75
0.45
0.2
0.08
0.08
ZD(1) ZE(1)
1.4
1.1
1.4
1.1
θ
o
7
o
0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT612-3
Fig 8.
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
02-07-12
04-07-05
MS-026
Package outline SOT612-3 (HLQFP144)
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
29 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
17. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
17.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
17.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
•
•
•
•
•
•
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
17.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
30 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
17.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 9) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 18 and 19
Table 18.
SnPb eutectic process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
≥ 350
< 2.5
235
220
≥ 2.5
220
220
Table 19.
Lead-free process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
350 to 2000
> 2000
< 1.6
260
260
260
1.6 to 2.5
260
250
245
> 2.5
250
245
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 9.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
31 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 9.
Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
18. Abbreviations
Table 20.
TDA19978B_2
Product data sheet
Abbreviations
Acronym
Description
ACR
Audio Clock Regeneration
AVR
Audio Video Receiver
AWG
American Wire Gauge
CMOS
Complementary Metal Oxide Semiconductor
DAC
Digital-to-Analog Converter
DDC-bus
Display Data Channel bus
DSD
Direct Stream Digital
DST
Direct Stream Transfer
DTS-HD
Digital Theater Systems High-Definition
DVD
Digital Versatile Disc
DVI
Digital Video Interface
EDID
Extended Display Identification Data
HBM
Human Body Model
HBR
High Bit Rate
HD
High-Definition
HDCP
High-bandwidth Digital Content Protection
HDMI
High-Definition Multimedia Interface
HDTV
High-Definition TeleVision
L-PCM
Linear-Pulse Code Modulation
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
32 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Table 20.
Abbreviations …continued
Acronym
Description
LSB
Least Significant Bit
LV-TTL
Low Voltage Transistor-Transistor Logic
NTSC
National Television Standards Committee
OBA
One Bit Audio
OTP
One Time Programmable
PAL
Phase Alternating Line
PLL
Phase-Locked Loop
RGB
Red Green Blue
SACD
Super Audio CD
SVGA
Super Video Graphics Array
SXGA
Super eXtended Graphics Array
S/PDIF
Sony/Philips Digital Interface Format
TMDS
Transition Minimized Differential Signaling
UXGA
Ultra eXtended Graphics Array
VGA
Video Graphics Array
WUXGA
Wide Ultra eXtended Graphics Array
XGA
eXtended Graphics Array
YCbCr
Y = Luminance, Cb = Chroma blue, Cr = Chroma red
YUV
Y = Luminance, U and V are chrominance signals
19. Revision history
Table 21.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
TDA19978B_2
20100510
Product data sheet
-
TDA19978B_1
Modifications:
TDA19978B_1
TDA19978B_2
Product data sheet
•
Section 1 “General description”: replaced 2.25 gigasamples per second by 2.05
gigasamples per second
•
•
•
•
•
•
Section 1 “General description”: updated the Deep Color mode in 12-bit
Section 2 “Features and benefits”: replaced 225 MHz by 205 MHz
Table 1 “Quick reference data”: updated
Section 8.5 “Activity detection”: replaced 225 MHz by 205 MHz
Table 10 “Characteristics”: updated
Table 17 “Example of supported video formats”: updated
20080807
Product data sheet
-
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
-
© NXP B.V. 2010. All rights reserved.
33 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
20. Legal information
20.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
20.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
20.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
34 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
20.4 Licenses
Purchase of NXP ICs with HDMI technology
Use of an NXP IC with HDMI technology in equipment that complies with
the HDMI standard requires a license from HDMI Licensing LLC, 1060 E.
Arques Avenue Suite 100, Sunnyvale CA 94085, USA, e-mail:
[email protected].
20.5 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
21. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
35 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
22. Tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Quick reference data . . . . . . . . . . . . . . . . . . . . .3
Ordering information . . . . . . . . . . . . . . . . . . . . .3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5
Audio port configuration (Layout 0) . . . . . . . . .12
Audio port configuration (Layout 1) . . . . . . . . .12
Audio port configuration for HBR and DST
packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
I2C-bus slave address . . . . . . . . . . . . . . . . . . .16
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . .16
Thermal characteristics . . . . . . . . . . . . . . . . . .17
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .17
Output in 12-bit video port format (mapping
example 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Output in 12-bit video port format (mapping
example 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Output in 10-bit video port format (mapping
example 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Output in 10-bit video port format (mapping
example 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Output in 8-bit video port format (mapping
example 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Output in 8-bit video port format (mapping
example 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Example of supported video formats . . . . . . . .26
SnPb eutectic process (from J-STD-020C) . . .31
Lead-free process (from J-STD-020C) . . . . . .31
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .32
Revision history . . . . . . . . . . . . . . . . . . . . . . . .33
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
36 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
23. Figures
Fig 1.
Fig 2.
Fig 3.
Fig 4.
Fig 5.
Fig 6.
Fig 7.
Fig 8.
Fig 9.
Block diagram of TDA19978B . . . . . . . . . . . . . . . .4
Pin configuration for TDA19978B . . . . . . . . . . . . .5
An example of an application with EDID memory
shared over all four HDMI inputs . . . . . . . . . . . . .15
An example of an application with EDID shared
over three HDMI inputs . . . . . . . . . . . . . . . . . . . .16
Output timing diagram pin VCLK and pins
VP[29:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Output timing diagram pin ACLK and pins
AP[5:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Application diagram of TDA19978B. . . . . . . . . . .28
Package outline SOT612-3 (HLQFP144) . . . . . .29
Temperature profiles for large and small
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
TDA19978B_2
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 02 — 10 May 2010
© NXP B.V. 2010. All rights reserved.
37 of 38
TDA19978B
NXP Semiconductors
Quad HDMI 1.3a receiver with digital processing
24. Contents
1
2
3
4
5
6
7
7.1
7.2
8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
8.20
8.21
8.22
8.23
8.24
8.24.1
8.24.2
9
10
11
12
13
14
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 2
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Quick reference data . . . . . . . . . . . . . . . . . . . . . 3
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pinning information . . . . . . . . . . . . . . . . . . . . . . 5
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
Functional description . . . . . . . . . . . . . . . . . . . 9
Software drivers . . . . . . . . . . . . . . . . . . . . . . . . 9
HDMI inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Termination resistance control . . . . . . . . . . . . . 9
Equalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Activity detection. . . . . . . . . . . . . . . . . . . . . . . 10
Color depth unpacking . . . . . . . . . . . . . . . . . . 10
Derepeater . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Upsample . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Packet extraction . . . . . . . . . . . . . . . . . . . . . . 10
Audio PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Audio formatter . . . . . . . . . . . . . . . . . . . . . . . . 11
Sync timing measurement . . . . . . . . . . . . . . . 13
Format measurement timing. . . . . . . . . . . . . . 13
Color space conversion . . . . . . . . . . . . . . . . . 13
4:2:2 downsampling filters . . . . . . . . . . . . . . . 13
Range control . . . . . . . . . . . . . . . . . . . . . . . . . 13
Dithering function . . . . . . . . . . . . . . . . . . . . . . 13
4:2:2 formatter . . . . . . . . . . . . . . . . . . . . . . . . 14
Video port selection . . . . . . . . . . . . . . . . . . . . 14
Output buffers . . . . . . . . . . . . . . . . . . . . . . . . . 14
VHREF timing generator . . . . . . . . . . . . . . . . 14
I2C-bus serial interface . . . . . . . . . . . . . . . . . . 14
Power management . . . . . . . . . . . . . . . . . . . . 15
EDID memory management . . . . . . . . . . . . . . 15
EDID memory shared over all four HDMI
inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
EDID memory shared over three HDMI
inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
I2C-bus protocol. . . . . . . . . . . . . . . . . . . . . . . . 16
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 16
Thermal characteristics . . . . . . . . . . . . . . . . . 17
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 17
Output video port formats
(mapping examples) . . . . . . . . . . . . . . . . . . . . 20
Example of supported video formats. . . . . . . 26
15
16
17
17.1
17.2
17.3
17.4
18
19
20
20.1
20.2
20.3
20.4
20.5
21
22
23
24
Application information . . . . . . . . . . . . . . . . .
Package outline. . . . . . . . . . . . . . . . . . . . . . . .
Soldering of SMD packages . . . . . . . . . . . . . .
Introduction to soldering. . . . . . . . . . . . . . . . .
Wave and reflow soldering. . . . . . . . . . . . . . .
Wave soldering . . . . . . . . . . . . . . . . . . . . . . .
Reflow soldering . . . . . . . . . . . . . . . . . . . . . .
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . .
Legal information . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . .
Licenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . . .
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
29
30
30
30
30
31
32
33
34
34
34
34
35
35
35
36
37
38
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2010.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 10 May 2010
Document identifier: TDA19978B_2