REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED Add device types 05, 06, 07, and 08. Add case outline C. Make changes to 1.2.2, 1.3, table I, and figure 1. - ro 00-09-28 R. MONNIN B Drawing updated to reflect current requirements. - gt 02-04-24 R. MONNIN C Make change to the VICR test and CMRR test conditions as specified in table I. - ro 02-10-03 R. MONNIN D Five year review requirement. - ro 07-10-02 R. HEBER E Make corrections to θJC and θJA limits for all case outlines under paragraph 1.3. Make correction to case outline H terminal symbols for device types 05 and 06 under figure 1. Update paragraphs to current MIL-PRF-38535 requirements. Delete references to device class M requirements. - ro 13-03-06 C. SAFFLE A REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY RAJESH PITHADIA STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil CHECKED BY RAJESH PITHADIA APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A RAYMOND MONNIN DRAWING APPROVAL DATE 00-06-23 REVISION LEVEL E MICROCIRCUIT, LINEAR, BICMOS, LOW POWER, RAIL-TO-RAIL INPUT/OUTPUT, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 5962-00512 1 OF 13 5962-E212-13 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 00512 Federal stock class designator \ RHA designator (see 1.2.1) 01 Q H A Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function TLV2460M TLV2460AM TLV2461M TLV2461AM TLV2462M TLV2462AM TLV2463M TLV2463AM Single operational amplifier with Shutdown Single operational amplifier with Shutdown Single operational amplifier without Shutdown Single operational amplifier without Shutdown Dual operational amplifier without Shutdown Dual operational amplifier without Shutdown Dual operational amplifier with Shutdown Dual operational amplifier with Shutdown 01 02 03 04 05 06 07 08 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter C H P 2 Descriptive designator GDIP1-T14 or CDIP2-T14 GDFP1-F10 or CDFP2-F10 GDIP1-T8 or CDIP2-T8 CQCC1-N20 Terminals 14 10 8 20 Package style Dual-in-line Flat pack Dual-in-line Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 2 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage range (VDD) ............................................................................ 6 V Differential input voltage (VID) ......................................................................... VDD − 0.2 V to VDD + 0.2 V Input current, (IIN) (any input) ......................................................................... +200 mA Output current, (IOUT) ..................................................................................... +175 mA Total input current, (II) (into +VDD) ................................................................. 175 mA Total output current, (Io) (out of GND) ............................................................ 175 mA Continuous total power dissipation (PD): Cases C and 2 ............................................................................................. Case H ........................................................................................................ Case P ......................................................................................................... Operating free-air temperature range (TA) ...................................................... Storage temperature range ............................................................................. Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds .................... Maximum junction temperature (TJ) ................................................................ Thermal resistance, junction-to-case (θJC): Case C ........................................................................................................ Case H ........................................................................................................ Case P ......................................................................................................... Case 2 ......................................................................................................... Thermal resistance, junction-to-ambient (θJA): Case C ........................................................................................................ Case H ........................................................................................................ Case P ......................................................................................................... Case 2 ......................................................................................................... 1375 mW 675 mW 1050 mW o o -55 C to +125 C o o -65 C to +150 C o +260 C o +150 C 12.9°C/W 11.3°C/W 12.9°C/W 12.1°C/W 83°C/W 197°C/W 122°C/W 83°C/W 1.4 Recommended operating conditions. Single supply voltage range (VDD) .................................................................. +2.7 V to +6 V Split supply voltage range (+VDD) .................................................................. +1.35 V to +3 V Common-mode input voltage (VICR) ............................................................... GND to +VDD o o Ambient operating temperature (TA) ............................................................... -55 C to +125 C ______ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ All voltage values, except differential voltages, are with respect to GND. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in MIL-PRF-38535. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55°C ≤ TA ≤ +125°C unless otherwise specified Group A subgroups Device type Limits 1/ Min Input offset voltage VIO VDD = +1.5 V, VIC = 0 V, VOUT = 0 V, RS = 50 Ω VDD = +2.5 V, VIC = 0 V, VOUT = 0 V, RS = 50 Ω VDD = 3 V, Gnd, VIC = 0 V, VOUT = 1.5 V, RS = 50 Ω VDD = 5 V, Gnd, VIC = 0 V, VOUT = 2.5 V, RS = 50 Ω Input offset current IIO VDD = +1.5 V, RS = 50 Ω, VIC = 0 V, VOUT = 0 V, VDD = +2.5 V, RS = 50 Ω, VIC = 0 V, VOUT = 0 V, Input bias current IIB VDD = +1.5 V, RS = 50 Ω, VIC = 0 V, VOUT = 0 V, VDD = +2.5 V, RS = 50 Ω, VIC = 0 V, VOUT = 0 V, Unit Max 1 01,03, 2000 2,3 05,07 2200 1 02,04, 1500 2,3 06,08 1700 1 01,03, 2000 2,3 05,07 2200 1 02,04, 1500 2,3 06,08 1700 1 01,03, 2000 2,3 05,07 2200 1 02,04, 1500 2,3 06,08 1700 1 01,03, 2000 2,3 05,07 2200 1 02,04, 1500 2,3 06,08 1700 1 All 7 nA 2,3 75 1 7 2,3 60 1 All µV 14 2,3 75 1 14 2,3 60 nA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 5 TABLE I. Electrical performance characteristics – Continued. Test Symbol Conditions -55°C ≤ TA ≤ +125°C unless otherwise specified Group A subgroups Device type Limits 1/ Min Common-mode input voltage range CMRR > 66 dB, VICR 1 RS = 50 Ω, VDD = 3 V CMRR > 60 dB, RS = 50 Ω, VDD = 3 V CMRR > 71 dB, RS = 50 Ω, VDD = 5 V CMRR > 60 dB, RS = 50 Ω, VDD = 5 V High-level output voltage Low output voltage Short-circuit output current Large signal differential voltage amplification VOH VOL IOS AVD All 0 to 3.0 1 -0.2 to 5.2 2,3 0 to 5 All 2.5 IOH = -2.5 mA, VDD = 5 V 4.8 IOH = -10 mA, VDD = 5 V 4.7 1,2,3 V 2.8 IOH = -10 mA, VDD = 3 V IOL = 2.5 mA, VIC = 1.5 V Max -0.2 to 3.2 2,3 1,2,3 IOH = -2.5 mA, VDD = 3 V Unit All V 0.2 IOL = 10 mA, VIC = 1.5 V 0.5 IOL = 2.5 mA, VIC = 2.5 V 0.2 IOL = 10 mA, VIC = 2.5 V 0.3 1,2,3 Sourcing, VDD = +1.5 V All 20 Sinking, VDD = +1.5 V 20 Sourcing, VDD = +2.5 V 60 Sinking, VDD = +2.5 V 60 1 VDD = +1.5 V, RL = 10 kΩ VDD = +2.5 V, RL = 10 kΩ All mA 90 2,3 89 1 92 2,3 90 V dB See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 6 TABLE I. Electrical performance characteristics – Continued. Test Symbol Conditions -55°C ≤ TA ≤ +125°C unless otherwise specified Group A subgroups Device type Limits 1/ Min Common-mode rejection ratio CMRR 1 VICR = 0 V to 3 V, RS = 50 Ω, VDD = 3 V kSVR (∆VDD / ∆VIO) 60 1 71 RS = 50 Ω, VDD = 5 V 2,3 60 VIC = VDD / 2, no load, 1 VDD = 2.7 V to 6.0 V VIC = VDD / 2, no load, VDD = 3.0 V to 5.0 V Supply current per channel IDD VDD = 3 V VOUT = 2.5 V, no load, VDD = 5 V Supply current per channel in shutdown SHDN < 0.8 V, IDD(SHDN) 75 1 85 2,3 80 All SR dB 0.575 2,3 0.9 1 0.65 2,3 1 01,02, 07,08 2.5 mA µA 3 VDD = 5 V 4 VOUT(PP) = 2 V, All 5, 6 CL = 160 pF, RL = 10 kΩ 1/ 2,3 1,2,3 VDD = 3 V dB 80 SHDN < 1.3 V, (For devices with shutdown feature) Slew rate All 1 VOUT = 1.5 V, no load, Max 66 2,3 VICR = 0 V to 5 V, Supply voltage rejection ratio All Unit 1 V/µs 0.8 All characteristics are measured with zero common-mode input voltages unless otherwise noted. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shall be provided with each lot of microcircuits delivered to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 7 01 and 02 (with shutdown) Device types Case outlines H Terminal number P 2 Terminal symbol 1 NC NC NC 2 NC -INPUT 1 NC 3 -INPUT 1 +INPUT 1 NC 4 +INPUT 1 -VDD / GND NC 5 -VDD / GND NC -INPUT 1 6 NC OUTPUT NC 7 OUTPUT +VDD +INPUT 1 8 +VDD SHDN NC 9 SHDN --- NC 10 NC --- -VDD / GND 11 --- --- NC 12 --- --- NC 13 --- --- NC 14 --- --- NC 15 --- --- OUTPUT 16 --- --- NC 17 --- --- +VDD 18 --- --- NC 19 --- --- NC 20 --- --- SHDN NC = No connect FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 8 03 and 04 (without shutdown) Device types Case outlines H Terminal number P 2 Terminal symbol 1 NC NC NC 2 NC -INPUT 1 NC 3 -INPUT 1 +INPUT 1 NC 4 +INPUT 1 -VDD / GND NC 5 -VDD / GND NC -INPUT 1 6 NC OUTPUT NC 7 OUTPUT +VDD +INPUT 1 8 +VDD NC NC 9 NC --- NC 10 NC --- -VDD / GND 11 --- --- NC 12 --- --- NC 13 --- --- NC 14 --- --- NC 15 --- --- OUTPUT 16 --- --- NC 17 --- --- +VDD 18 --- --- NC 19 --- --- NC 20 --- --- NC NC = No connect FIGURE 1. Terminal connections – Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 9 05 and 06 (without shutdown) Device types Case outlines H Terminal number P 2 Terminal symbol 1 NC OUTPUT 1 NC 2 OUTPUT 1 -INPUT 1 OUTPUT 1 3 -INPUT 1 +INPUT 1 -INPUT 1 4 +INPUT 1 -VDD / GND +INPUT 1 5 -VDD / GND +INPUT 2 NC 6 +INPUT 2 -INPUT 2 -VDD / GND 7 -INPUT 2 OUTPUT 2 NC 8 OUTPUT 2 +VDD NC 9 +VDD --- NC 10 NC --- NC 11 --- --- NC 12 --- --- NC 13 --- --- NC 14 --- --- NC 15 --- --- NC 16 --- --- +INPUT 2 17 --- --- NC 18 --- --- -INPUT 2 19 --- --- OUTPUT 2 20 --- --- +VDD NC = No connect FIGURE 1. Terminal connections – Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 10 07 and 08 (with shutdown) Device types Case outlines C Terminal number 2 Terminal symbol 1 OUTPUT 1 NC 2 -INPUT 1 OUTPUT 1 3 +INPUT 1 -INPUT 1 4 -VDD / GND +INPUT 1 5 NC NC 6 SHDN 1 -VDD / GND 7 NC NC 8 NC NC 9 SHDN 2 SHDN 1 10 NC NC 11 +INPUT 2 NC 12 -INPUT 2 NC 13 OUTPUT 2 SHDN 2 14 +VDD NC 15 --- NC 16 --- +INPUT 2 17 --- NC 18 --- -INPUT 2 19 --- OUTPUT 2 20 --- +VDD NC = No connect FIGURE 1. Terminal connections – Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 11 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. 4.2.1 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections, and as specified herein. 4.4.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein. 4.4.2.1 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table II herein. 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). a. End-point electrical parameters shall be as specified in table II herein. b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535 for the RHA level being tested. All device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25°C ±5°C, after exposure, to the subgroups specified in table II herein. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 12 TABLE II. Electrical test requirements. Test requirements Interim electrical parameters (see 4.2) Final electrical parameters (see 4.2) Group A test requirements (see 4.4) Group C end-point electrical parameters (see 4.4) Group D end-point electrical parameters (see 4.4) Group E end-point electrical parameters (see 4.4) Subgroups (in accordance with MIL-PRF-38535, table III) Device Device class Q class V ----1,2,3,4,5,6 1/ 1,2,3,4,5,6 1/ 1,2,3,4,5,6 1,2,3,4,5,6 1 1 1 1 --- --- 1/ PDA applies to subgroup 1. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q and V. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor prepared specification or drawing. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform DLA Land and Maritime when a system application requires configuration control and which SMD's are applicable to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.4 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0540. 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in MIL-HDBK-103 and QML-38535. The vendors listed in MIL-HDBK-103 and QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DLA Land and Maritime-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-00512 A REVISION LEVEL E SHEET 13 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 13-03-06 Approved sources of supply for SMD 5962-00512 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-0051201QHA 01295 TLV2460MUB 5962-0051201QPA 01295 TLV2460MJGB 5962-0051201Q2A 01295 TLV2460MFKB 5962-0051202QHA 01295 TLV2460AMUB 5962-0051202QPA 01295 TLV2460AMJGB 5962-0051202Q2A 01295 TLV2460AMFKB 5962-0051203QHA 01295 TLV2461MUB 5962-0051203QPA 01295 TLV2461MJGB 5962-0051203Q2A 01295 TLV2461MFKB 5962-0051204QHA 01295 TLV2461AMUB 5962-0051204QPA 01295 TLV2461AMJGB 5962-0051204Q2A 01295 TLV2461AMFKB 5962-0051205QHA 01295 TLV2462MUB 5962-0051205QPA 01295 TLV2462MJGB 5962-0051205Q2A 01295 TLV2462MFKB 5962-0051206QHA 01295 TLV2462AMUB 5962-0051206QPA 01295 TLV2462AMJGB 5962-0051206Q2A 01295 TLV2462AMFKB 1 of 2 STANDARD MICROCIRCUIT DRAWING BULLETIN – CONTINUED. DATE: 13-03-06 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-0051207QCA 01295 TLV2463MUB 5962-0051207Q2A 01295 TLV2463MFKB 5962-0051208QCA 01295 TLV2463AMUB 5962-0051208Q2A 01295 TLV2463AMFKB 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number Vendor name and address 01295 Texas Instruments Incorporated Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 2 of 2