K11041 Series 5V Clock Driver For 32-Bit Micro-processors ! ! ! ! 40MHz to 70MHz Frequency Range TTL Compatible Waveform Load Capacity of 50pF Rise Time of 1.7ns Max., Fall Time of 1.6ns Max. for Meeting Tight Electrical Specifications of the High Speed Motorola MC68030 and MC68040 ax. mM m 2 13, ax. mM m 8 20, Z 41 E K1150.000 MHTE COD 5 TI DA C m 2m 6,2 x. Ma ! Tri-State Output ! “M” Models Operate -40oC to 85oC ! Replaces Model K11040T PIN 1 K11041 Capabilities The Champion Technologies K11041 Data Clock Oscillator is designed specifically to drive the Motorola MC68030 and MC68040 families of 32-bit microprocessors. This device also provides precise timing for 486 and Pentium® processors. Meeting these stringent requirements also makes the K11041 ideal for other applications requiring tightly controlled duty cycle or very fast rise and fall times. E L E C T R I C A L S P E C I F I C AT I O N S MODEL K11041 Frequency Range (MHz) Discrete Frequencies to 140MHz Frequency Stability (ppm) Overall Inclusive of calibration, temperature, voltage, load, shock,vibration, aging OBSOLETE Popular frequencies of the K11041 Series Clocks are 40.000 MHz, 60.000 MHz and 66.667 MHz. Other frequencies available. Pentium® is a registered trademark of Intel Corp. 0°C to 70°C ±100 Temperature Range (°C) Operating Storage Supply Voltage (V) Supply Current (mA) 0°C to +70°C -55°C to +125°C +5.0 ±5% 50 (CL = 50pF) Output TTL Symmetry (%) 45/55 @ Vm “0” Level (VOL) 0.4V min. @ IOL = +24mA “1” Level (VOH) 2.5V min. @ IOH = -24mA Start Up Time (ms) < 20 Phase Jitter (ps) < 100 PA R T N U M B E R I N G G U I D E K11041X - Specify Frequency “Blank” = 0oC to 70oC Operating Temperature “M” = -40oC to 85oC Operating Temperature 2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585 800-888-1499 or www.champtech.com 1 K11041 Series 5V Clock Driver For 32-Bit Micro-processors PIN FUNCTION 1 Tri-State* 2 Ground 3 Output 4 + VCC * Input tied internally to +3.3V dc. External input if any, should not be less than +3V and not greater than +3.8V dc. Tri-State Control* PIN 1 PIN 8 Low (VL = 1.35V High Impedance Max.) Open* FO OBSOLETE TEST CIRCUIT DIAGRAM SHIPPING TUBE CROSS SECTION MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS REFERENCE PROCEDURES DESCRIPTION Temperature Cycle MIL-STD-833, Mtd 1010, Cond. B -55°C to +125°C; Air-to-Air; 100 cycles; 10 min. dwell Mechanical Shock MIL-STD-883, Mtd 2002, Cond. B 1500 g’s Vibration MIL-STD 883, Mtd 2007, Cond. B 20-2000 Hz; 0.06 inch; 15g’s; 3 planes Humidity Steady State MIL-STD-202, Mtd 103 40°C; 90%-95% R.H.; 56 days Thermal Shock MIL-STD-883, Mtd 1011.7 Cond. B 100°C to 0°C; Water-to-Water; 15 cycles Electrostatic Discharge MIL-STD-883, Mtd 3015 Class II 2 KV to 4 KV Threshold Solderability Hermeticity MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He Resistance to Soldering Lead Integrity 235°C; 30 seconds MIL-STD-202, Mtd 210D, Cond. J MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress Marking Permanence Life Test MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125°C, powered, 1000 hours minimum 2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585 800-888-1499 or www.champtech.com 2