Features • Industry Standard Architecture – Emulates Many 20-Pin PALs® – Low Cost Easy-to-Use Software Tools • High-Speed Electrically Erasable Programmable Logic Devices – 7.5 ns Maximum Pin-to-Pin Delay • Several Power Saving Options Device ICC, Stand-By ICC, Active ATF16V8B 50 mA 55 mA ATF16V8BQ 35 mA 40 mA ATF16V8BQL 5 mA 20 mA HighPerformance Flash PLD • CMOS and TTL Compatible Inputs and Outputs – Input and I/O Pull-Up Resistors • Advanced Flash Technology – Reprogrammable – 100% Tested • High Reliability CMOS Process – 20 Year Data Retention – 100 Erase/Write Cycles – 2,000V ESD Protection – 200 mA Latchup Immunity • Commercial, and Industrial Temperature Ranges • Dual-in-Line and Surface Mount Packages in Standard Pinouts ATF16V8B Block Diagram TSSOP Top View Pin Configurations Pin Name Function CLK Clock I Logic Inputs I/O Bidirectional Buffers OE Output Enable VCC +5 V Supply I/CLK I1 I2 I3 I4 I5 I6 I7 I8 GND 1 2 3 4 5 6 7 8 9 10 DIP/SOIC 20 19 18 17 16 15 14 13 12 11 VCC I/O I/O I/O I/O I/O I/O I/O I/O I9/OE PLCC Top View Rev. 0364E–07/98 1 Description The ATF16V8B is a high performance CMOS (Electrically Erasable) Programmable Logic Device (PLD) which utilizes Atmel’s proven electrically erasable Flash memory technology. Speeds down to 7.5 ns are offered. All speed ranges are specified over the full 5V ± 10% range for industrial temperature ranges, and 5V ± 5% for commercial temperature ranges. Several low power options allow selection of the best solution for various types of power-limited applications. Each of these options significantly reduces total system power and enhances system reliability. The ATF16V8Bs incorporate a superset of the generic architectures, which allows direct replacement of the 16R8 family and most 20-pin combinatorial PLDs. Eight outputs are each allocated eight product terms. Three different modes of operation, configured automatically with software, allow highly complex logic functions to be realized. Absolute Maximum Ratings* Temperature Under Bias .................................-55oC to +125oC *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note: Minimum voltage is -0.6V DC, which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V DC, which may overshoot to 7.0V for pulses of less than 20 ns. Storage Temperature ......................................-65oC to +150oC Voltage on Any Pin with Respect to Ground .......................................-2.0 V to +7.0 V(1) Voltage on Input Pins with Respect to Ground During Programming...................................-2.0 V to +14.0 V(1) 1. Programming Voltage with Respect to Ground .....................................-2.0 V to +14.0 V(1) DC and AC Operating Conditions Commercial Operating Temperature (Case) VCC Power Supply 2 ATF16V8B o o Industrial 0 C - 70 C -40oC - 85oC 5V ± 5% 5V ± 10% ATF16V8B DC Characteristics Symbol Parameter Condition IIL Input or I/O Low Leakage Current 0 ≤ VIN ≤ VIL(MAX) IIH Input or I/O High Leakage Current 3.5 ≤ VIN ≤ VCC Min Typ Max Units -35 -100 µA 10 µA Com. 55 85 mA Ind. 55 95 mA Com. 50 75 mA Ind. 50 80 mA Com. 35 55 mA Com. 5 10 mA Ind. 5 15 mA Com. 60 90 mA Ind. 60 100 mA Com. 55 85 mA Ind. 55 95 mA Com. 40 55 mA Com. 20 35 mA Ind. 20 40 mA -130 mA B-7, -10 ICC Power Supply Current, Standby VCC = MAX, VIN = MAX, Outputs Open B-15, -25 BQ-10 BQL-15, -25 B-7, -10 ICC2 Clocked Power Supply Current VCC = MAX, Outputs Open, f=15 MHz B-15, -25 BQ-10 BQL-15, -25 IOS(1) Output Short Circuit Current VIL Input Low Voltage -0.5 0.8 V VIH Input High Voltage 2.0 VCC+0.75 V VOL Output High Voltage VIN=VIH or VIL, VCC=MIN IOL = -24 mA Com., Ind. 0.5 V VOH Output High Voltage VIN=VIH or VIL, VCC=MIN IOH = -4.0 mA Note: VOUT = 0.5 V 2.4 V 1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec. 3 AC Waveforms(1) Note: 1. Timing measurement reference is 1.5V. Input AC driving levels are 0.0V 3.0V, unless otherwise specified. AC Characteristics(1) -7(2) -10 -15 -25 Symbol Parameter tPD Input or Feedback to Non-Registered Output tCF Clock to Feedback tCO Clock to Output 2 tS Input or Feedback Setup Time 5 7.5 12 15 ns tH Hold Time 0 0 0 0 ns tP Clock Period 8 12 16 24 ns tW Clock Width 4 6 8 12 ns FMAX 8 outputs switching Min Max Min Max Min Max Min Max Units 3 7.5 3 10 3 15 3 25 ns 1 output switching 7 ns 3 5 6 2 7 8 2 10 2 10 ns 12 ns External Feedback 1/(tS+tCO) 100 68 45 37 MHz Internal Feedback 1/(tS + tCF) 125 74 50 40 MHz No Feedback 1/(tP) 125 83 62 41 MHz tEA Input to Output Enable — Product Term 3 9 3 10 3 15 3 20 ns tER Input to Output Disable — Product Term 2 9 2 10 2 15 2 20 ns tPZX OE pin to Output Enable 2 6 2 10 2 15 2 20 ns OE pin to Output Disable 1.5 6 1.5 10 1.5 15 1.5 20 ns tPXZ Notes: 1. See ordering information for valid part numbers and speed grades. 2. Recommend ATF16V8C-7. 4 ATF16V8B ATF16V8B Input Test Waveforms and Measurement Levels: Output Test Loads: Commercial tR, tF < 5 ns (10% to 90%) Pin Capacitance f = 1 MHz, T = 25°C(1) Typ Max Units CIN 5 8 pF VIN = 0 V COUT 6 8 pF VOUT = 0 V Note: Conditions 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. Power Up Reset The registers in the ATF16V8Bs are designed to reset during power up. At a point delayed slightly from VCC crossing VRST, all registers will be reset to the low state. As a result, the registered output state will always be high on power-up. This feature is critical for state machine initialization. However, due to the asynchronous nature of reset and the uncertainty of how VCC actually rises in the system, the following conditions are required: 1) The VCC rise must be monotonic, 2) After reset occurs, all input and feedback setup times must be met before driving the clock pin high, and 3) The clock must remain stable during tPR. Preload of Registered Outputs The ATF16V8B’s registers are provided with circuitry to allow loading of each register with either a high or a low. This feature will simplify testing since any state can be forced into the registers to control test sequencing. A JEDEC file with preload is generated when a source file with vectors is compiled. Once downloaded, the JEDEC file preload sequence will be done automatically by most of the approved programmers after the programming. Parameter Description Typ Max Units tPR Power-Up Reset Time 600 1,000 ns VRST Power-Up Reset Voltage 3.8 4.5 V Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the ATF16V8B fuse patterns. Once programmed, fuse verify and preload are inhibited. However, the 64-bit User Signature remains accessible. The security fuse should be programmed last, as its effect is immediate. 5 Electronic Signature Word Input and I/O Pull-Ups There are 64 bits of programmable memory that are always available to the user, even if the device is secured. These bits can be used for user-specific data. All ATF16V8B family members have internal input and I/O pull-up resistors. Therefore, whenever inputs or I/Os are not being driven externally, they will float to V CC . This ensures that all logic array inputs are at known states. These are relatively weak active pull-ups that can easily be overdriven by TTL-compatible drivers (see input and I/O diagrams below). Programming/Erasing Programming/erasing is performed using standard PLD programmers. See CMOS PLD Programming Hardware and Software Support for information on software/programming. Input Diagram I/O Diagram Functional Logic Diagram Description The Logic Option and Functional Diagrams describe the ATF16V8B architecture. Eight configurable macrocells can be configured as a registered output, combinatorial I/O, combinatorial output, or dedicated input. The ATF16V8B can be configured in one of three different modes. Each mode makes the ATF16V8B look like a different device. Most PLD compilers can choose the right mode automatically. The user can also force the selection by supplying the compiler with a mode selection. The determining factors would be the usage of register versus combinatorial outputs and dedicated outputs versus outputs with output enable control. The ATF16V8B universal architecture can be programmed to emulate many 20-pin PAL devices. These architectural subsets can be found in each of the configuration modes described in the following pages. The user can download the listed subset device JEDEC programming file to the PLD programmer, and the ATF16V8B can be configured to act like the chosen device. Check with your programmer manufacturer for this capability. Unused product terms are automatically disabled by the compiler to decrease power consumption. A Security Fuse, when programmed, protects the content of the ATF16V8B. Eight bytes (64 fuses) of User Signature are accessible to the user for purposes such as storing project name, part number, revision, or date. The User Signature is accessible regardless of the state of the Security Fuse. Compiler Mode Selection Registered Complex Simple Auto Select ABEL, Atmel-ABEL P16V8R P16V8C P16V8AS P16V8 CUPL G16V8MS LOG/iC GAL16V8_R OrCAD-PLD “Registered” PLDesigner Tango-PLD Note: 6 G16V8MA (1) G16V8 (1) GAL16V8_C8 GAL16V8 “Complex” “Simple” GAL16V8A P16V8R P16V8C P16V8C P16V8A G16V8R G16V8C G16V8AS G16V8 1. Only applicable for version 3.4 or lower. ATF16V8B GAL16V8_C7 G16V8AS (1) ATF16V8B Macrocell Configuration Software compilers support the three different OMC modes as different device types. Most compilers have the ability to automatically select the device type, generally based on the register usage and output enable (OE) usage. Register usage on the device forces the software to choose the registered mode. All combinatorial outputs with OE controlled by the product term will force the software to choose the complex mode. The software will choose the simple mode only when all outputs are dedicated combinatorial without OE control. The different device types can be used to override the automatic device selection by the software. For further details, refer to the compiler software manuals. When using compiler software to configure the device, the user must pay special attention to the following restrictions in each mode. In registered mode pin 1 and pin 11 are permanently configured as clock and output enable, respectively. These pins cannot be configured as dedicated inputs in the registered mode. In complex mode pin 1 and pin 11 become dedicated inputs and use the feedback paths of pin 19 and pin 12 respectively. Because of this feedback path usage, pin 19 and pin 12 do not have the feedback option in this mode. In simple mode all feedback paths of the output pins are routed via the adjacent pins. In doing so, the two inner most pins (pins 15 and 16) will not have the feedback option as these pins are always configured as dedicated combinatorial output. ATF16V8B Registered Mode PAL Device Emulation / PAL Replacement The registered mode is used if one or more registers are required. Each macrocell can be configured as either a registered or combinatorial output or I/O, or as an input. For a registered output or I/O, the output is enabled by the OE pin, and the register is clocked by the CLK pin. Eight product terms are allocated to the sum term. For a combinatorial output or I/O, the output enable is controlled by a product term, and seven product terms are allocated to the sum term. When the macrocell is configured as an input, the output enable is permanently disabled. Any register usage will make the compiler select this mode. The following registered devices can be emulated using this mode: 16R8 16RP8 16R6 16RP6 16R4 16RP4 Registered Configuration for Registered Mode(1)(2) Combinatorial Configuration for Registered Mode(1)(2) Notes: Notes: 1. 2. Pin 1 cotrols common CLK for the registered outputs. Pin 11 controls common OE for the registered outputs. Pin 1 and Pin 11 are permanently configured as CLK and OE. The development software configures all the architecture control bits and checks for proper pin usage automatically. 1. Pin 1 and Pin 11 are permanently configured as CLK and OE. 2. The development software configures all the architecture control bits and checks for proper pin usage automatically. 7 Registered Mode Logic Diagram 8 ATF16V8B ATF16V8B ATF16V8B Complex Mode PAL Device Emulation/PAL Replacement In the Complex Mode, combinatorial output and I/O functions are possible. Pins 1 and 11 are regular inputs to the array. Pins 13 through 18 have pin feedback paths back to the AND-array, which makes full I/O capability possible. Pins 12 and 19 (outermost macrocells) are outputs only. They do not have input capability. In this mode, each mac- rocell has seven product terms going to the sum term and one product term enabling the output. Combinatorial applications with an OE requirement will make the compiler select this mode. The following devices can be emulated using this mode: 16L8 16H8 16P8 Complex Mode Option ATF16V8B Simple Mode PAL Device Emulation / PAL Replacement In the Simple Mode, 8 product terms are allocated to the sum term. Pins 15 and 16 (center macrocells) are permanently configured as combinatorial outputs. Other macrocells can be either inputs or combinatorial outputs with pin feedback to the AND-array. Pins 1 and 11 are regular inputs. The compiler selects this mode when all outputs are combinatorial without OE control. The following simple PALs can be emulated using this mode: 10L8 10H8 10P8 12L6 12H6 12P6 14L4 14H4 14P4 16L2 16H2 16P2 Simple Mode Option * - Pins 15 and 16 are always enabled. 9 Complex Mode Logic Diagram 10 ATF16V8B ATF16V8B Simple Mode Logic Diagram 11 SUPPLY CURRENT vs. INPUT FREQUENCY SUPPLY CURRENT vs. INPUT FREQUENCY ATF16V8BL/BQL (VCC = 5V, TA = 25C) ATF16V8B/BQ (VCC = 5V, TA = 25C) 75 75 ATF16V8BL ATF16V8B I C C 50 m A 25 ATF16V8BQ 0 25 50 75 100 SUPPLY CURRENT vs. SUPPLY VOLTAGE ATF16V8B/BQ (TA = 25C) 65 ATF16V8B 55 ATF16V8BQ 45 35 25 4.50 4.75 5.00 5.25 5.50 SUPPLY VOLTAGE (V) OUTPUT SOURCE CURRENT vs. SUPPLY VOLTAGE (TA = 25C) -10 -12 I O H -14 -16 -18 m A -20 -22 -24 4.5 4.7 4.9 5.1 5.3 SUPPLY VOLTAGE (V) 12 m A 25 ATF16V8BQL 0 20 40 60 FREQUENCY (MHz) FREQUENCY (MHz) m A 50 0 0 I C C I C C ATF16V8B 5.5 80 100 ATF16V8B NORMALIZED TPD vs. SUPPLY VOLTAGE (TA=25°C) 1.3 N O R M T P D 1.15 ATF16V8B/BQ 1 ATF16V8BQL 0.85 0.7 4.50 4.75 5.00 5.25 5.50 SUPPLY VOLTAGE (V) NORMALIZED TCO vs. SUPPLY VOLTAGE(TA=25°C) 1.3 N O 1.15 ATF16V8B/BQ R M 1 ATF16V8BQL T C 0.85 O 0.7 4.50 4.75 5.00 5.25 5.50 SUPPLY VOLTAGE (V) 13 14 ATF16V8B ATF16V8B Ordering Information tPD (ns) tS (ns) tCO (ns) Ordering Code (1) Package Operation Range 7.5 5 5 ATF16V8B-7JC ATF16V8B-7PC(1) ATF16V8B-7SC(1) ATF16V8B-7XC(1) 20J 20P3 20S 20X Commercial (0°C to 70°C) 10 7.5 7 ATF16V8B-10JC ATF16V8B-10PC ATF16V8B-10SC ATF16V8B-10XC 20J 20P3 20S 20X Commercial (0°C to 70°C) ATF16V8B-10JI ATF16V8B-10PI ATF16V8B-10SI ATF16V8B-10XI 20J 20P3 20S 20X Industrial (-40°C to 85°C) ATF16V8B-15JC ATF16V8B-15PC ATF16V8B-15SC ATF16V8B-15XC 20J 20P3 20S 20X Commercial (0°C to 70°C) ATF16V8B-15JI ATF16V8B-15PI ATF16V8B-15SI ATF16V8B-15XI 20J 20P3 20S 20X Industrial (-40°C to 85°C) ATF16V8B-25JC ATF16V8B-25PC ATF16V8B-25SC ATF16V8B-25XC 20J 20P3 20S 20X Commercial (0°C to 70°C) ATF16V8B-25JI ATF16V8B-25PI ATF16V8B-25SI ATF16V8B-25XI 20J 20P3 20S 20X Industrial (-40°C to 85°C) 15 25 Note: 12 15 10 12 1. Recommend ATF16V8C-7. 15 Ordering Information tPD (ns) tS (ns) tCO (ns) 10 7.5 15 25 Ordering Code Package 7 ATF16V8BQ-10JC ATF16V8BQ-10PC ATF16V8BQ-10SC ATF16V8BQ-10XC 20J 20P3 20S 20X Commercial (0°C to 70°C) 12 10 ATF16V8BQL-15JC ATF16V8BQL-15PC ATF16V8BQL-15SC ATF16V8BQL-15XC 20J 20P3 20S 20X Commercial (0°C to 70°C) 15 12 ATF16V8BQL-25JC ATF16V8BQL-25PC ATF16V8BQL-25SC ATF16V8BQL-25XC 20J 20P3 20S 20X Commercial (0°C to 70°C) ATF16V8BQL-25JI ATF16V8BQL-25PI ATF16V8BQL-25SI ATF16V8BQL-25XI 20J 20P3 20S 20X Industrial (-40°C to 85°C) Package Type 20J 20-Lead, Plastic J-Leaded Chip Carrier (PLCC) 20P3 20-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 20S 20-Lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC) 20X 20-Lead, 4.4 mm Wide, Plastic Thin Shrink Small Outline (TSSOP) 16 ATF16V8B Operation Range ATF16V8B Packaging Information 20J, 20-Lead, Plastic J-Leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-018 AA 20P3, 20-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-001 AD 1.060(26.9) .980(24.9) PIN 1 .280(7.11) .240(6.10) .090(2.29) MAX .900(22.86) REF .210(5.33) MAX .005(.127) MIN SEATING PLANE .015(.381) MIN .150(3.81) .115(2.92) .022(.559) .014(.356) .070(1.78) .045(1.13) .110(2.79) .090(2.29) .325(8.26) .300(7.62) 0 REF 15 .014(.356) .008(.203) .430(10.92) MAX 20S, 20-Lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC) Dimensions in Inches and (Millimeters) 20X, 20-Lead, 4.4 mm Wide, Plastic Thin Shrink Small Outline (TSSOP) Dimensions in Millimeters and (Inches) 0.020 (0.508) 0.013 (0.330) 0.30(0.012) 0.18(0.007) 0.299 (7.60) 0.420 (10.7) 0.291 (7.39) 0.393 (9.98) PIN 1 4.48(.176) 6.50(.256) 4.30(.169) 6.25(.246) PIN 1 ID .050 (1.27) BSC 0.65(.0256) BSC 0.513 (13.0) 0.497 (12.6) 0.105 (2.67) 0.092 (2.34) 6.60(.260) 6.40(.252) 0.15(.006) 0.05(.002) 0.012 (0.305) 0.003 (0.076) 0 REF 8 1.10(0.043) MAX 0.18(.007) 0.09(.003) 0.013 (0.330) 0.009 (0.229) 0.035 (0.889) 0.015 (0.381) 0 REF 8 0.70(.028) 0.50(.020) 17