ROHM BD9267KUT-XX

BD9267KUT
Datasheet
LED Drivers for LCD Backlights
White LED Diver for
Backlight of Medium/Large-sized LCDs
BD9267KUT
●General Description
BD9267KUT is a white LED diver used on backlight of
Medium/Large-sized LCDs. This IC can achieve
dimming function by SPI control. And through the SPI
correspondence, it can set the ON/OFF of each switch,
analog dimming and etc. The signals of PWM dimming
can set the frequency, ON time and delay of PWM by
inputting the external signals to the register.
BD9267KUT has equipped several protection functions
to deal with the abnormal states, including LED OPEN
protection, LED SHORT protection, external current
setting resistance SHORT protection, external MOS
transistor SHORT protection, etc. So it can be used in a
wide output voltage range and various load conditions.
●Key Specifications
■
VCC power supply range:
9.0V~35.0V
■
DVDD power supply range:
3.0V~3.6V
■
CLK frequency setting range:
100~10000kHz
■
Operating Circuit current range:
2.4mA(typ.)
■
Operating temperature range:
-40℃~+85℃
●Features
■ 16-ch constant current driver (external FET(NMOS)is
equipped.)
■ LED voltage can be set externally.
■ PWM dimming and Analogue dimming can be
controlled by SPI.
■ LED Abnormal operation detection circuit (OPEN
protection/ SHORT protection) is equipped.
■ LED SHORT protection detection voltage is adjustable
(LSP terminal)
■ LED SHORT protection detection CH
■ FAIL INDICATION function is equipped by ERR_DET
terminal.
■ 3 lines serial interface
■ Package: TQFP64U
●Package
TQFP64U
Pin Pitch
W(Typ.) D(Typ.) H(Max.)
9.00mm×9.00mm×1.20mm
0.4mm
●Applications
TV、PC display
Other LCD backlight
Figure 1. TQFP64U
●Typical Application Circuit
Figure 2. Typical Application Circuit
○Product structure:Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays
www.rohm.com
TSZ02201-0F1F0C100050-1-2
© 2012 ROHM Co., Ltd. All rights reserved.
1/28
TSZ22111・14・001
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Absolute Maximum Ratings(Ta=25℃)
Parameter
Symbol
Ratings
Unit
VCC
36
V
Power Supply Voltage at digital part
DVDD
4.5
V
STB Terminal Voltage
VSTB
VCC
V
Power Supply Voltage
VD1~VD16
D1~16 Terminal Voltage
VERR_DET
ERR_DET Terminal Voltage
S1~S16, G1~G16, VREF5V, LSP,
VS1~S16, VG1~VG16,VREF5V,VLSP,
VCOMP1,VCOMP2
COMP1, COMP2 Terminal Voltage
CS, CLK, DI, DO, VSYNC, HSYNC Terminal
VCS,VCLK,VDI,VDO,VVSYNC,VHSYNC
Voltage
Pd
Power Dissipation
40
V
VCC
V
7
V
4.5
750
*1
V
mW
Operating Temperature Range
Topr
-40~+85
℃
Storage temperature range
Tstg
-55~+150
℃
℃
Tjmax
150
Junction temperature
*1 When Ta = 25°C or higher, power dissipation is d own with 6.0mW/°C (when a 70 mm x 70 mm x 16 mm 4-l ayer glass
epoxy board is mounted).
●Operation range(Ta=25℃)
Parameter
Symbol
Limits
Unit
Power source voltage
VCC
9.0~35.0
V
Power Supply Voltage at digital part
DVDD
3.0~3.6
V
CLK oscillation frequency setting range
fCLK
100~10000
kHz
fVSYNC
80 ~ 1000
Hz
VSYNC input oscillation frequency range
VLSP
0.8 ~ 3.0
V
LSP terminal input voltage
The operating ranges above are acquired by evaluating the IC separately. Please take care when set the IC in applications.
●Block diagram
●Package outline drawing
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
G16
D16
S16
G15
D15
S15
G14
D14
S14
G13
D13
S13
G12
D12
S12
G11
TQFP64U
9.0±0.3
7.0±0.2
48
49 VREF5V
D11
32
50
LSP
S11
31
51
VCC
G10
30
52
STB
D10
29
53
GND
S10
28
54 COMP2
G9
27
55 COMP1
D9
26
33
32
7.0±0.2
9.0±0.3
49
D9267KUT
DGND
S9
25
57
CS
S8
24
58
CLK
D8
23
59
DI
G8
22
60
DO
S7
21
61 VSYNC
D7
20
62 HSYNC
G7
19
63 ERR_DET
S6
18
64
D6
17
64
17
D2
S2
G3
D3
S3
G4
D4
S4
G5
D5
S5
G6
5
6
7
8
9
10
11
12
13
14
15
16
S1
3
G2
D1
4
G1
1
2
0.1±0.1
0.15±0.1
16
0.4
LOT No.
0.125±0.1
0.08
(Unit : mm)
Figure 3. Pin Configuration
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
1.0±0.1
DVDD
1.2Max.
1
0.5
BD9267KUT
56
Figure 4. Marking Diagram
2/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Electrical characteristics (unless otherwise specified, Ta = 25°C, VCC = 12V, STB=3V)
Item
Symbol
Standard value
Minimum
【Whole device】
】
Operating circuit
Icc
-
current
Stand-by circuit
IST
-
current
【VREF5V block】
】
VREF5V output
VREF5
4.95
voltage
VREF5V Maximum
IREF5
15
output current
【Error amplifier block】
】
COMP1,COMP2
ICOMPSINK
300
terminal sink current
LED control voltage
VLED
270
【UVLO block】
】
Operation power
VUVLO_VCC
6.0
source voltage(VCC)
hysteresis voltage
VUHYS_VCC
150
(VCC)
【LED DRIVER block】
】
LED terminal current
⊿ILED
-1.5
accuracy
OPEN detection
VOPEN
0.05
voltage
SHORT detection
VSHORT
4.5
voltage
Upper resistance of
divided LSP terminal
RupLSP
1000
resistance
Lower resistance of
divided LSP terminal
RdownLSP
250
resistance
Error detection of
current detection
VRESSH
0.10
resistance
【STB block】
】
STB terminal HIGH
STBH
2.0
voltage
STB terminal LOW
STBL
-0.3
voltage
STB terminal Pull
REN
600
Down resistance
【FAIL block】
】
ERR_DET terminal
RFAIL
55
ON resistance
【LOGIC input (CS, CLK, DI, HSYNC, VSYNC)】
】
0.7×
Input High voltage
VINH
DVDD
Unit
Condition
Standard
Maximum
2.4
5.0
mA
LED1-16 OFF
200
500
µA
STB=0V
5.00
5.05
V
IO=0mA
-
-
mA
-
-
µA
300
330
mV
7.0
8.0
V
300
600
mV
-
1.5
%
ILED=100mA
0.10
0.15
V
VD=SWEEP DOWN
5.0
5.5
V
VD=SWEEP UP
-
-
kΩ
LSP=0V
-
-
kΩ
LSP=3V
0.15
0.20
V
-
VCC
V
-
0.8
V
1000
1800
kΩ
VIN=3V( STB )
110
220
Ω
IERR_DET=5mA
-
VCOMP=0.5V
VCC=SWEEP UP
VCC=SWEEP DOWN
DVDD
+0.3
0.3×
DVDD
5
µA
VIN=3.3V
V
Input Low voltage
VINL
-0.3
-
V
Input inflow current
IIN1
-5
0
Output High voltage
VOUTH
DVDD
-0.6
DVDD
-0.3
-
V
IOL=-1mA
Output Low voltage
VOUTL
-
0.19
0.60
V
IOL=1mA
【LOGIC output (DO) 】
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
3/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Terminal No, name, and function
Terminal
Function
G1
CH1 NMOS gate
terminal
2
D1
CH1 NMOS drain
terminal
3
S1
CH1 NMOS source
terminal
G2
CH2 NMOS gate
terminal
D2
CH2 NMOS drain
terminal
6
S2
CH2 NMOS source
terminal
7
G3
8
No.
No.
Terminal
Function
No.
No.
Terminal
Function
G11
CH11 NMOS gate
terminal
49
VREF5V
5V regulator output terminal
50
LSP
SHORT detection setting
terminal
Power source terminal
Terminal
Function
D6
CH6 NMOS drain
terminal
18
S6
CH6 NMOS source
terminal
34
S12
CH12 NMOS source
terminal
19
G7
CH7 NMOS gate
terminal
35
D12
CH12 NMOS drain
terminal
51
VCC
D7
CH7 NMOS drain
terminal
36
G12
CH12 NMOS gate
terminal
52
STB
Enable terminal
S7
CH7 NMOS source
terminal
37
S13
CH13 NMOS source
terminal
53
GND
GND terminal
22
G8
CH8 NMOS gate
terminal
38
D13
CH13 NMOS drain
terminal
54
COMP2
ERROR AMP output
(CH1~8)
CH3 NMOS gate
terminal
23
D8
CH8 NMOS drain
terminal
39
G13
CH13 NMOS gate
terminal
55
COMP1
ERROR AMP output
(CH9~16)
D3
CH3 NMOS drain
terminal
24
S8
CH8 NMOS source
terminal
40
S14
CH14 NMOS source
terminal
56
DGND
Digital GND terminal
9
S3
CH3 NMOS source
terminal
25
S9
CH9 NMOS source
terminal
41
D14
CH14 NMOS drain
terminal
57
CS
Chip select terminal
10
G4
CH3 NMOS gate
terminal
26
D9
CH9 NMOS drain
terminal
42
G14
CH14 NMOS gate
terminal
58
CLK
Clock input terminal
D4
CH4 NMOS drain
terminal
G9
CH9 NMOS gate
terminal
S15
CH15 NMOS source
terminal
59
DI
DATE input terminal
12
S4
CH4 NMOS source
terminal
28
S10
CH10 NMOS source
terminal
44
D15
CH15 NMOS drain
terminal
60
DO
DATE output terminal
13
G5
CH5 NMOS gate
terminal
29
D10
CH10 NMOS drain
terminal
45
G15
CH15 NMOS gate
terminal
61
VSYNC
VSYNC signal terminal
14
D5
CH5 NMOS drain
terminal
30
G10
CH10 NMOS gate
terminal
46
S16
CH16 NMOS source
terminal
62
HSYNC
HSYNC signal terminal
15
S5
CH5 NMOS source
terminal
31
S11
CH11 NMOS source
terminal
47
D16
CH16 NMOS drain
terminal
63
ERR_DET
Abnormal detection output
terminal
16
G6
CH6 NMOS gate
terminal
32
D11
CH11 NMOS drain
terminal
48
G16
CH16 NMOS gate
terminal
64
DVDD
Digital Power source
terminal
1
4
5
11
17
20
21
27
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
33
43
4/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Internal Equivalent Circuit Diagram
G1~
~G16
D1~
~D16
S1~
~S16
VREF5V
LSP
STB
VREF5V
2MΩ
LSP
500kΩ
GND
COMP1, COMP2
CS, CLK, DI
DO
DVDD
DVDD
DVDD
DVDD
CS,CLK,DI
DO
10kΩ
50Ω
DGND
DGND
GND
DGND
VSYNC, HSYNC
ERR_DET
ERR_DET
50Ω
GND
GND
GND
Figure 5. Pin ESD Type
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
5/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Block Diagram
DVDD
VREF5V
VREF5V
STB
LSP
ERR_DET
VCC
VREF
PWM1
FB1
+
REG
UVLO
FB16
GND
OPEN
DET
SHORT
DET
-
MS1
UVLO
DVDD
MS1
DI
FPGA
MS16
CLK
MOS
SHORT
DET
D1
PWM2
+
-
G1
MS2
CH1
S1
PWM16
Protect
logic
SPI I/F
CS
RES
SHORT
DET
LED16_dr_moni
LED
LED1_dr_moni
LED
D2
+
-
G2
MS16
DO
LED_ref
DAC
CH2
S2
DGND
register
EAMP_ref
DAC
FB1
LED1_dr_moni
FB2
LED2_dr_moni
D16
VSYNC
(ON timming)
PWM
DUTY
HSYNC
(clock)
FB1
+
FB8
+
-
FB9
+
FB16
+
-
PWM1
PWM16
CONTROL
G16
CH16
S16
LED16_dr_moni
FB16
COMP2
COMP1
Figure 6-1. Block Diagram
SPI
CS
DI
CLK
DO_EN
DO
SPI
LED_EN_01~16
LTCH
LTCH
HSYNC
1/4
LED_REF_01~12
LTCH
EAMP_DAC_01~12
DEC
CHCONT_*
DLY_LTCH REG(12bit)
COMP
S
R
Q
PWM_ OUT_*
EN
HSYNC4I
HSYNCI
DLY COUNTER(12bit)
DTY_LTCH REG(12bit)
COMP
DTY COUNTER(12bit)
S
1
VSYNC
0
err_led_op
Q
Edge_det
err_led_sh
LED_OP_DET
LED_SH_DET
RES_SH_DET
Q
MOS_SH_DET
ERR_OUT_*
err_res_sh
ERR_MSK_CNT (6bit)
RISE
SEL
ERR_MSK_CNT (6bit)
FALL
SEL
Q
err_mos_sh
Q
pwm_aftr_msk
PWM_MSK_CNT (6bit)
Edge_det
* : 01~16
Figure 6-2. Logic Block Diagram
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
6/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Typical Performance Curves
400
5.0
4.5
350
4.0
300
3.5
250
Icc [mA]
IST [uA]
3.0
200
2.5
2.0
150
1.5
100
1.0
50
0.5
0
0.0
9
13
17
21
25
29
33
9
VCC [V]
13
17
21
25
29
33
VCC [V]
Figure 8. Operating Current (Icc) [mA] vs. VCC[V]
(LED1-16 OFF)
Figure 7. Stand-by Current (IST) [µA] vs. VCC[V]
5.5
5.4
5.3
VREF5V [V]
5.2
5.1
5.0
4.9
4.8
4.7
4.6
4.5
9
13
17
21
25
29
33
VCC [V]
Figure 9. VREF5V[V] vs. VCC[V]
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
7/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Pin Function Descriptions
G1-G16 (1,4,7,10,13,16,19,22,27,30,33,36,39,42,45,48PIN)
External FET gate driving terminal of LED constant current driver, operating range : 0~5V.
S1-S16 (3,6,9,12,15,18,21,24,25,28,31,34,37,40,43,46PIN)
Connect to external FET’s source terminal of LED constant current driver。Through the operations of constant current
driver, all CHs of S1-S16 terminals are outputted the set voltages at addresses of 02h, 03h, and S1-S16 proceed the
constant current operation.
By monitoring the voltage of this terminal, the external resistance SHORT detection of each CH and external MOS
SHORT during Drain-Source detection proceed.
When Dimming=HIGH, external resistance SHORT detection proceeds, and output the errors.
When Dimming=LOW, external MOS Drain-Source SHORT detection proceeds, and output the errors.
D1-D16 (2,5,8,11,14,17,20,23,26,29,32,35,38,41,44,47PIN)
At output terminal of LED constant current driver, drain of external FET is connected. By monitoring the voltage of this
terminal, LED OPEN detection and LED SHORT detection of each terminal proceed.
When Dimming=HIGH, if LED is in SHORT mode or OPEN mode, error signals are outputted.
LED OPEN protection detected voltage ・・・0.1V(typ.)
LED SHORT protection detected voltage・・・5.0V(typ.)・・・(It can be changed by setting the LSP terminal. Details are
given in LSP Pin Description.)
When Dimming = LOW, the abnormal state when Dimming = HIGH just before continues. In other words, when
Dimming=HIGH and the abnormal state is detected, the error signal is still outputted even turned to Dimming=LOW.
To prevent the mistake of detection caused by the time change of state, abnormal detection mask can be set at address
of 04h.
At D1~16 pin
① LED OPEN detection(when PWM=H)
② LED SHORT detection(when PWM=H)
At S1~16 pin
③ RESISTOR SHORT detection(when PWM=H)
④ MOS SHORT detection(when PWM=L)
are detected, then the error signals are outputted.
Figure 10. LED Protected operation
VREF5V (49PIN)
The VREF5V pin is used to output power (5V) to the internal block of the IC and serves as a main power supply for the
internal circuit of the IC. Install a ceramic capacitor as close to this pin as possible in order to stabilize the power supply
voltage.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
8/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
LSP (50PIN)
A pin used for setting the LED SHORT protection detecting
voltage. When LSP pin is in OPEN state, the voltage in inward
of IC is 1V typ.(Set it in range of 0.8V~3.0V)
When LED is lighting, if the voltage of D1~16 pin is higher
than
「Voltage of LSP x 5 (V) 」
(default 5V)
the abnormal state of IC is detected。
Because this pin has a high impedance, please connect a
capacitor about 1000pF to remove the noise basically.
…
Figure 11. LSP Pin Internal Equivalent Circuit Diagram
BSx Pin LED short detect voltage [V]
In case of outputting a voltage to LSP by using the resistor divider circuit, REF5V
VIN
R1
LSP
LSP
R2
CLSP
AGND
AGND
AGND
20
15
10
5
0
0
Figure 12. Setting for LSP
1
2
LSP Pin voltage [V]
3
4
Figure 13. LED SHORT detect Voltage [V] vs. LSP [V]
VCC (51PIN)
The VCC pin is used to supply power for the IC in the range of 9 to 35V. If the VCC pin voltage reaches 7.0V (Typ.) or
more, the IC will initiate operation. If it reaches 6.7V (Typ.) or less, the IC will be shut down. Basically, insert a resistor of
approx. 10 ohms in resistance between the VCC pin and the external power supply and install a ceramic capacitor of
approx. 1uF in capacitance in the vicinity of the IC.
STB (52PIN)
The STB pin is used to make setting of turning ON and OFF the IC and allowed for use to reset the IC from shutdown.
Note: Set the STB pin voltage below the VCC pin voltage.
Note: The IC state is switched (i.e., the IC is switched between ON and OFF state) according to voltages input in the STB
pin. Avoid using the STB pin between two states (0.8 to 1.8V).
GND(53PIN)
The GND pin is an analog circuit ground pin of the IC. Set the ground pattern as close as possible to that of resistors
connected to the S1 to S16 pins.
COMP1(55PIN)
The COMP1 pin is used to feed back the state of voltage to the external power supply in order to optimize the power
supply voltage for the LED layer.
Positive feedback voltage is output to a pin having the lowest voltage out of the D1 to D8 pins. If the lowest voltage of the
D1 to D8 pins is higher than 0.6V typical voltage, the COMP1 pin will become open-circuited. If the lowest voltage of
these pins is lower than 0.6V typical voltage, the internal NPN transistor of the COMP1 pin will turn ON. The COMP1 pin
is intended to connect to the output voltage monitor pin of the DC/DC converter.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
9/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
COMP2(54PIN)
The COMP2 pin is used to feed back the state of voltage to the external power supply in order to optimize the power
supply voltage for the LED layer.
Positive feedback voltage is output to a pin having the lowest voltage out of the D9 to D16 pins. If the lowest voltage of
the D9 to D16 pins is higher than 0.6V typical voltage, the COMP2 pin will become open-circuited. If the lowest voltage of
these pins is lower than 0.6V typical voltage, the internal NPN transistor of the COMP2 pin will turn ON. The COMP2 pin
is intended to connect to the output voltage monitor pin of the DC/DC converter.
CS(57PIN), CLK(58PIN,) DI(59PIN), DO(60PIN)
These pins are used to control the IC with the CS, CLK, DI, and DO serial interfaces. Input levels are determined by the
DVDD power supply of the digital block. For data input format and timing, refer to the description of Logic block to be
hereinafter provided.
Input State
Input Level
High-level input
DVDD×0.7~ DVDD+0.3[V]
Low-level input
-0.3~DVDD×0.3 [V]
VSYNC(61PIN), HSYNC(62PIN)
The VSYNC and HSYNC input signals enable the PWM light modulation signal to make setting of PWM frequency, PWM
ON time, and PWM delay time. For data input format and timing, refer to the description of Logic block to be hereinafter
provided.
ERR_DET(63PIN)
The ERR_DET pin is used to output an IC error detection signal and provides the N-MOS open-drain output function. If
this pin is pulled up to the DVDD voltage of the IC or else, it will be set to output High voltage for normal operation. If any
error is detected, the internal NMOS of the IC will be put into ON state, setting the pin to output Low voltage.
State
FAIL Signal Output
Normal operation
OPEN
LED error detection
GND Level
When the ERR_DET pin is put into the GND Level, the LED has already caused an error. In this case, reading the
registers located at addresses 05h to 0Ch makes it possible to recognize what channel is in what type of error state. (For
detail, refer to the description of registers to be hereinafter provided.)
DGND(56PIN)
The DGND pin is a digital circuit ground pin of the IC. Lay out the DGND pin using interconnect independent of that for
the GND pin wherever possible.
DVDD(64PIN)
The DVDD pin is used to input power in the digital block of the IC in the range of 3.0 to 3.6V. When the DVDD pin voltage
reaches 3.3V (typ.), the IC will start operating. Insert a ceramic capacitor of approx. 1uF in capacitance between the DVDD
and DGND pins in the vicinity of the IC.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
10/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Functions of Logic Block
Serial interface block
This IC is controlled with the CS, CLK, DI, and DO serial interfaces.
The following section describes data input format and timing.
◆WRITE MODE
・To write 1 byte of data:
CS
tCYC
tCLKH
tCSS
1
2
3
4
5
6
tCSH
7
8
9
10
11
12
13
14
15
16
CLK
tDIS
DI
tDIH
A6
tCLKL
A5
A4
A3
A2
A1
W
A0
D7
D6
D5
D4
D3
D2
D1
D0
Low
DO
Figure 14. WRITE MODE (for 1byte)
・Write consecutive 32 bytes of data:
CS
①
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CLK
DI
②
A6
A5
A4
A3
A2
A1
A0
③
D255 D254 D253 D252 D251 D250 D249 D248
W
Low
DO
④
①
17
18
19
20
21
22
23
24
257
258
259
260
261
262
263
264
②
③
D247 D246 D245 D244 D243 D242 D241 D240
D7
D6
D5
D4
D3
D2
D1
D0
Low
④
Figure 15. WRITE MODE (for 32byte)
Addresses are automatically counted up in increments of 1 address by 8 bits after the first set value.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
11/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
◆READ MODE
CS
tCYC
tCLKH
tCSS
1
2
3
4
5
6
tCSH
7
8
9
10
11
12
13
14
15
16
CLK
tDIS
DI
tDIH
A6
A5
t
CLKL
A4
A3
A2
A1
A0
R
*
*
*
*
*
*
*
*
D6
D5
D4
D3
D2
D1
D0
tDOD
D7
Low
DO
DO_EN
Figure 16. READ MODE
AC electrical characteristics:
Parameter
CLK cycle
CLK high level range
CLK low level range
DI input setup time
DI input hold time
CS input setup time
CS input hold time
DO output delay time
Symbol
tCYC
tCLKH
tCLKL
tDIS
tDIH
tCSS
tCSH
tDOD
Min.
100
35
35
50
50
50
50
-
Rating
Typ.
-
Max.
40
Unit
ns
ns
ns
ns
ns
ns
ns
ns
(Output load capacitance: 15pF)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
12/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
◆Register map(
(1/3)
)
Address
R/W
Default
Register Name
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
Description
00h
R/W
FFh
LEDENA
LEDEN[7]
LEDEN[6]
LEDEN[5]
LEDEN[4]
LEDEN[3]
LEDEN[2]
LEDEN[1]
LEDEN[0]
Ch1 to Ch8 LED Enable
01h
R/W
FFh
LEDENB
LEDEN[15]
LEDEN[14]
LEDEN[13]
LEDEN[12]
LEDEN[11]
LEDEN[10]
LEDEN[9]
LEDEN[8]
Ch9~Ch16 LED Enable
02h
R/W
66h
LEDREFL
LEDREF[7]
LEDREF [6]
LEDREF [5]
LEDREF[4]
LEDREF [3]
LEDREF [2]
LEDREF[1]
LEDREF[0]
Analog light modulation (Low 9 bits)
03h
R/W
02h
LEDREFM
-
-
-
-
LEDREF[11]
LEDREF[10]
LEDREF [9]
LEDREF [8]
Analog light modulation (High 4 bits)
04h
R/W
02h
MASKSET
-
-
-
-
-
-
ERRMSK[1]
ERRMSK[0]
Mask time setting
05h
R
00h
ERRLEDOPA
ERLOP_08
ERLOP_07
ERLOP_06
ERLOP_05
ERLOP_04
ERLOP_03
ERLOP_02
ERLOP_01
Ch1 to Ch8 ERR pin monitor (LEDOP)
06h
R
00h
ERRLEDOPB
ERLOP_16
ERLOP_15
ERLOP_14
ERLOP_13
ERLOP_12
ERLOP_11
ERLOP_10
ERLOP_09
Ch9 to Ch16ERROR pin monitor (LEDOP)
07h
R
00h
ERRLEDSHA
ERLSH_08
ERLSH_07
ERLSH_06
ERLSH_05
ERLSH_04
ERLSH_03
ERLSH_02
ERLSH_01
Ch1 to Ch8ERR pin monitor (LEDSH)
08h
R
00h
ERRLEDSHB
ERLSH_16
ERLSH_15
ERLSH_14
ERLSH_13
ERLSH_12
ERLSH_11
ERLSH_10
ERLSH_09
Ch9 to Ch16ERRO pin monitor (LEDSH)
09h
R
00h
ERRRESSHA
ERRSH_08
ERRSH_07
ERRSH_06
ERRSH_05
ERRSH_04
ERRSH_03
ERRSH_02
ERRSH_01
Ch1 to Ch8ERR pin monitor (RESSH)
0Ah
R
00h
ERRRESHB
ERRSH_16
ERRSH_15
ERRSH_14
ERRSH_13
ERRSH_12
ERRSH_11
ERRSH_10
ERRSH_09
Ch9 to Ch16ERROR pin monitor (RESSH)
0Bh
R
00h
ERRMOSSHA
ERMSH_08
ERMSH_07
ERMSH_06
ERMSH_05
ERMSH_04
ERMSH_03
ERMSH_02
ERMSH_01
Ch1 to Ch8ERR pin monitor (MOSSH)
0Ch
R
60h
ERRMOSSHB
ERMSH_16
ERMSH_15
ERMSH_14
ERMSH_13
ERMSH_12
ERMSH_11
ERMSH_10
ERMSH_09
Ch9 to Ch16ERROR pin monitor (MOSSH)
0Dh
R/W
00h
DUMMY
DMY08
DMY07
DMY06
DMY05
DMY04
DMY03
DMY02
DMY01
Dummy register
0Eh
R/W
60h
SYSCONFIG
EAMPREFC
EAMPREFB
EAMPREFA
VSYNCDIS
MOSSHDIS
RESSHDIS
LEDSHDIS
LEDOPDIS
Setting register
0Fh
R/W
00h
VSYNCREG
-
-
-
-
-
-
-
VSNC_REG
VSYNC signal input with register
10h
R/W
0Ch
SSMSKSET
SSMASK[7]
SSMASK[6]
SSMASK[5]
SSMASK[4]
SSMASK[3]
SSMASK[2]
SSMASK[1]
SSMASK[0]
Mask section setting for soft start
DTY01[4]
DTY01[3]
DTY01[2]
DTY01[1]
DTY01[0]
LED1 PWM ON range setting (Low 8 bits)
DTY01[11]
DTY01[10]
DTY01[9]
DTY01[8]
LED1 PWM ON range setting (High 4bit)
11h
R/W
00h
DTYCNT01L
DTY01[7]
DTY01[6]
DTY01[5]
12h
R/W
00h
DTYCNT01M
-
-
-
-
13h
R/W
00h
DTYCNT02L
DTY02[7]
DTY02[6]
DTY02[5]
DTY02[4]
DTY02[3]
DTY02[2]
DTY02[1]
DTY02[0]
LED2 PWM ON range setting (Low 8bit)
14h
R/W
00h
DTYCNT02M
-
-
-
-
DTY02[11]
DTY02[10]
DTY02[9]
DTY02[8]
LED2 PWM ON range setting (High 4bit)
15h
R/W
00h
DTYCNT03L
DTY03[7]
DTY03[6]
DTY03[5]
DTY03[4]
DTY03[3]
DTY03[2]
DTY03[1]
DTY03[0]
LED3 PWM ON range setting (Low 8bit)
16h
R/W
00h
DTYCNT03M
-
-
-
-
DTY03[11]
DTY03[10]
DTY03[9]
DTY03[8]
LED3 PWM ON range setting (High 4bit)
17h
R/W
00h
DTYCNT04L
DTY04[7]
DTY04[6]
DTY04[5]
DTY04[4]
DTY04[3]
DTY04[2]
DTY04[1]
DTY04[0]
LED4 PWM ON range setting (Low 8bit)
18h
R/W
00h
DTYCNT04M
-
-
-
-
DTY04[11]
DTY04[10]
DTY04[9]
DTY04[8]
LED4 PWM ON range setting (High 4bit)
19h
R/W
00h
DTYCNT05L
DTY05[7]
DTY05[6]
DTY05[5]
DTY05[4]
DTY05[3]
DTY05[2]
DTY05[1]
DTY05[0]
LED5 PWM ON range setting (Low 8bit)
1Ah
R/W
00h
DTYCNT05M
-
-
-
-
DTY05[11]
DTY05[10]
DTY05[9]
DTY05[8]
LED5 PWM ON range setting (High 4bit)
1Bh
R/W
00h
DTYCNT06L
DTY06[7]
DTY06[6]
DTY06[5]
DTY06[4]
DTY06[3]
DTY06[2]
DTY06[1]
DTY06[0]
LED6 PWM ON range setting (Low 8bit)
1Ch
R/W
00h
DTYCNT06M
-
-
-
-
DTY06[11]
DTY06[10]
DTY06[9]
DTY06[8]
LED6 PWM ON range setting (High 4bit)
1Dh
R/W
00h
DTY07[6]
DTY07[5]
DTY07[4]
DTY07[3]
DTY07[2]
DTY07[1]
DTY07[0]
LED7 PWM ON range setting (Low 8bit)
1Eh
R/W
00h
DTYCNT07M
-
-
-
-
DTY07[11]
DTY07[10]
DTY07[9]
DTY07[8]
LED7 PWM ON range setting (High 4bit)
1Fh
R/W
00h
DTYCNT08L
DTY08[7]
DTY08[6]
DTY08[5]
DTY08[4]
DTY08[3]
DTY08[2]
DTY08[1]
DTY08[0]
LED8 PWM ON range setting (Low 8bit)
20h
R/W
00h
DTY08[10]
DTY08[9]
DTY08[8]
LED8 PWM ON range setting (High 4bit)
21h
R/W
00h
DTYCNT09L
22h
R/W
00h
DTYCNT09M
23h
R/W
00h
24h
R/W
00h
DTYCNT10M
-
-
25h
R/W
00h
DTYCNT11L
DTY11[7]
DTY11[6]
26h
R/W
00h
27h
R/W
00h
DTYCNT07L
DTYCNT08M
DTYCNT10L
DTY07[7]
-
-
-
DTY08[11]
DTY09[7]
DTY09[6]
DTY09[5]
DTY09[4]
DTY09[3]
DTY09[2]
DTY09[1]
DTY09[0]
LED9 PWM ON range setting (Low 8bit)
-
-
-
-
DTY09[11]
DTY09[10]
DTY09[9]
DTY09[8]
LED9 PWM ON range setting (High 4bit)
DTY10[6]
DTY10[5]
DTY10[4]
DTY10[3]
DTY10[2]
DTY10[1]
DTY10[0]
LED10 PWM ON range setting (Low 8bit)
-
-
DTY10[11]
DTY10[10]
DTY10[9]
DTY10[8]
LED10 PWM ON range setting (High 4bit)
DTY11[5]
DTY11[4]
DTY11[3]
DTY11[2]
DTY11[1]
DTY11[0]
LED11 PWM ON range setting (Low 8bit)
DTY11[10]
DTY11[9]
DTY11[8]
LED11 PWM ON range setting (High 4bit)
DTY12[2]
DTY12[1]
DTY12[0]
LED12 PWM ON range setting (Low 8bit)
-
DTY10[7]
DTYCNT11M
-
-
-
-
DTY11[11]
DTYCNT12L
DTY12[7]
DTY12[6]
DTY12[5]
DTY12[4]
DTY12[3]
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
13/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
◆Register map(
(2/3)
)
Address
R/W
Default
Register Name
BIT7
BIT6
28h
R/W
00h
DTYCNT12M
-
-
29h
R/W
00h
DTY13[6]
2Ah
R/W
00h
DTYCNT13M
-
-
2Bh
R/W
00h
DTYCNT14L
DTY14[7]
DTY14[6]
2Ch
R/W
00h
DTYCNT14M
-
-
-
2Dh
R/W
00h
DTYCNT15L
DTY15[7]
DTY15[6]
DTY15[5]
2Eh
R/W
00h
DTYCNT15M
-
-
-
2Fh
R/W
00h
DTYCNT16L
DTY16[7]
DTY16[6]
DTY16[5]
30h
R/W
00h
DTYCNT16M
-
-
31h
R/W
00h
DLYCNT01L
DLY01[7]
DLY01[6]
32h
R/W
00h
DLYCNT01M
-
-
33h
R/W
00h
DLYCNT02L
DLY02[7]
34h
R/W
00h
DLYCNT02M
-
35h
R/W
00h
DLYCNT03L
DLY03[7]
36h
R/W
00h
DLYCNT03M
-
-
37h
R/W
00h
DLYCNT04L
DLY04[7]
DLY04[6]
38h
R/W
00h
DLYCNT04M
-
-
39h
R/W
00h
DLYCNT05L
DLY05[7]
3Ah
R/W
00h
DLYCNT05M
-
3Bh
R/W
00h
DLYCNT06L
DLY06[7]
3Ch
R/W
00h
DLYCNT06M
-
-
3Dh
R/W
00h
DLYCNT07L
DLY07[7]
DLY07[6]
3Eh
R/W
00h
DLYCNT07M
-
-
3Fh
R/W
00h
DLYCNT08L
DLY08[7]
40h
R/W
00h
DLYCNT08M
-
41h
R/W
00h
DLYCNT09L
DLY09[7]
42h
R/W
00h
DLYCNT09M
-
-
43h
R/W
00h
DLYCNT10L
DLY10[7]
DLY10[6]
44h
R/W
00h
DLYCNT10M
-
-
45h
R/W
00h
DLYCNT11L
DLY11[7]
DLY11[6]
46h
R/W
00h
DLYCNT11M
-
-
47h
R/W
00h
DLYCNT12L
DLY12[7]
DLY12[6]
48h
R/W
00h
DLYCNT12M
-
-
49h
R/W
00h
DLYCNT13L
DLY13[7]
4Ah
R/W
00h
DLYCNT13M
-
DTYCNT13L
DTY13[7]
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
BIT5
BIT4
BIT3
BIT2
-
-
DTY12[11]
DTY12[10]
DTY12[9]
DTY12[8]
LED12 PWM ON range setting (High 4bit)
DTY13[5]
DTY13[4]
DTY13[3]
DTY13[2]
DTY13[1]
DTY13[0]
LED13 PWM ON range setting (Low 8bit)
-
-
DTY13[11]
DTY13[10]
DTY13[9]
DTY13[8]
LED13 PWM ON range setting (High 4bit)
DTY14[5]
DTY14[4]
DTY14[3]
DTY14[2]
DTY14[1]
DTY14[0]
LED14 PWM ON range setting (Low 8bit)
-
DTY14[11]
DTY14[10]
DTY14[9]
DTY14[8]
LED14 PWM ON range setting (High 4bit)
DTY15[4]
DTY15[3]
DTY15[2]
DTY15[1]
DTY15[0]
LED15 PWM ON range setting (Low 8bit)
-
DTY15[11]
DTY15[10]
DTY15[9]
DTY15[8]
LED15 PWM ON range setting (High 4bit)
DTY16[4]
DTY16[3]
DTY16[2]
DTY16[1]
DTY16[0]
LED16 PWM ON range setting (Low 8bit)
-
-
DTY16[11]
DTY16[10]
DTY16[9]
DTY16[8]
LED16 PWM ON range setting (High 4bit)
DLY01[5]
DLY01[4]
DLY01[3]
DLY01[2]
DLY01[1]
DLY01[0]
LED1 PWM delay time setting (Low 8 bits)
-
-
DLY01[11]
DLY01[10]
DLY01[9]
DLY01[8]
LED1 PWM delay time setting (High 4 bits)
DLY02[6]
DLY02[5]
DLY02[4]
DLY02[3]
DLY02[2]
DLY02[1]
DLY02[0]
LED2 PWM delay time setting (Low 8bit)
-
-
-
DLY02[11]
DLY02[10]
DLY02[9]
DLY02[8]
LED2 PWM delay time setting (High 4bit)
DLY03[6]
DLY03[5]
DLY03[4]
DLY03[3]
DLY03[2]
DLY03[1]
DLY03[0]
LED3 PWM delay time setting (Low 8bit)
-
-
DLY03[11]
DLY03[10]
DLY03[9]
DLY03[8]
LED3 PWM delay time setting (High 4bit)
DLY04[5]
DLY04[4]
DLY04[3]
DLY04[2]
DLY04[1]
DLY04[0]
LED4 PWM delay time setting (Low 8bit)
-
-
DLY04[11]
DLY04[10]
DLY04[9]
DLY04[8]
LED4 PWM delay time setting (High 4bit)
DLY05[6]
DLY05[5]
DLY05[4]
DLY05[3]
DLY05[2]
DLY05[1]
DLY05[0]
LED5 PWM delay time setting (Low 8bit)
-
-
-
DLY05[11]
DLY05[10]
DLY05[9]
DLY05[8]
LED5 PWM delay time setting (High 4bit)
DLY06[6]
DLY06[5]
DLY06[4]
DLY06[3]
DLY06[2]
DLY06[1]
DLY06[0]
LED6PWM delay time setting (Low 8bit)
-
-
DLY06[11]
DLY06[10]
DLY06[9]
DLY06[8]
LED6 PWM delay time setting (High 4bit)
DLY07[5]
DLY07[4]
DLY07[3]
DLY07[2]
DLY07[1]
DLY07[0]
LED7 PWM delay time setting (Low 8bit)
-
-
DLY07[11]
DLY07[10]
DLY07[9]
DLY07[8]
LED7 PWM delay time setting (High 4bit)
DLY08[6]
DLY08[5]
DLY08[4]
DLY08[3]
DLY08[2]
DLY08[1]
DLY08[0]
LED8 PWM delay time setting (Low 8bit)
-
-
-
DLY08[11]
DLY08[10]
DLY08[9]
DLY08[8]
LED8 PWM delay time setting (High 4bit)
DLY09[6]
DLY09[5]
DLY09[4]
DLY09[3]
DLY09[2]
DLY09[1]
DLY09[0]
LED9 PWM delay time setting (Low 8bit)
-
-
DLY09[11]
DLY09[10]
DLY09[9]
DLY09[8]
LED9 PWM delay time setting (High 4bit)
DLY10[5]
DLY10[4]
DLY10[3]
DLY10[2]
DLY10[1]
DLY10[0]
LED10 PWM delay time setting (Low 8bit)
-
-
DLY10[11]
DLY10[10]
DLY10[9]
DLY10[8]
LED10 PWM delay time setting (High 4bit)
DLY11[5]
DLY11[4]
DLY11[3]
DLY11[2]
DLY11[1]
DLY11[0]
LED11 PWM delay time setting (Low 8bit)
-
-
DLY11[11]
DLY11[10]
DLY11[9]
DLY11[8]
LED11 PWM delay time setting (High 4bit)
DLY12[5]
DLY12[4]
DLY12[3]
DLY12[2]
DLY12[1]
DLY12[0]
LED12 PWM delay time setting (Low 8bit)
-
-
DLY12[11]
DLY12[10]
DLY12[9]
DLY12[8]
LED12 PWM delay time setting (High 4bit)
DLY13[6]
DLY13[5]
DLY13[4]
DLY13[3]
DLY13[2]
DLY13[1]
DLY13[0]
LED13 PWM delay time setting (Low 8bit)
-
-
-
DLY13[11]
DLY13[10]
DLY13[9]
DLY13[8]
LED13 PWM delay time setting (High 4bit)
14/28
BIT1
BIT0
Description
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
◆Register map (3/3)
)
Address
R/W
Default
Register Name
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
Description
4Bh
R/W
00h
DLYCNT14L
DLY14[7]
DLY14[6]
DLY14[5]
DLY14[4]
DLY14[3]
DLY14[2]
DLY14[1]
DLY14[0]
LED14 PWM delay time setting (Low 8bit)
4Ch
R/W
00h
DLYCNT14M
-
-
-
-
DLY14[11]
DLY14[10]
DLY14[9]
DLY14[8]
LED14 PWM delay time setting (High 4bit)
4Dh
R/W
00h
DLYCNT15L
DLY15[7]
DLY15[6]
DLY15[5]
DLY15[4]
DLY15[3]
DLY15[2]
DLY15[1]
DLY15[0]
LED15 PWM delay time setting (Low 8bit)
4Eh
R/W
00h
DLYCNT15M
-
-
-
-
DLY15[11]
DLY15[10]
DLY15[9]
DLY15[8]
LED15 PWM delay time setting (High 4bit)
4Fh
R/W
00h
DLYCNT16L
DLY16[7]
DLY16[6]
DLY16[5]
DLY16[4]
DLY16[3]
DLY16[2]
DLY16[1]
DLY16[0]
LED16 PWM delay time setting (Low 8bit)
50h
R/W
00h
DLYCNT16M
-
-
-
-
DLY16[11]
DLY16[10]
DLY16[9]
DLY16[8]
LED16 PWM delay time setting (High 4bit)
◆Description of registers
●ADDR=00h
LEDENA (Ch1 to Ch8 LED Enable control register: Read/Write)
Bit
7
6
5
4
Register Name
LEDEN[7]
LEDEN[6]
LEDEN[5]
LEDEN[4]
Default
1
1
1
1
3
2
1
0
LEDEN[3]
1
LEDEN[2]
1
LEDEN[1]
1
LEDEN[0]
1
●ADDR=01h
LEDENB (Ch9 to Ch16 LED enable control register: Read/Write)
Bit
7
6
5
4
Register Name LEDEN[15] LEDEN[14] LEDEN[13] LEDEN[12]
Default
1
1
1
1
3
2
1
0
LEDEN[11]
1
LEDEN[10]
1
LEDEN[9]
1
LEDEN[8]
1
LEDEN
0
1
Enable control
Disable
Enable
●ADDR=02h
LEDREFA (Analog light modulation setting register - Low 8 bits -: Read/Write)
Bit
7
6
5
4
3
Register Name
LEDREF[7]
LEDREF[6]
LEDREF[5]
LEDREF[4]
LEDREF[3]
Default
0
1
1
0
0
●ADDR=03h
LEDREFB (Analog light modulation setting register - High 4 bits -: Read/Write)
Bit
7
6
5
4
3
Register Name
LEDREF[11]
Default
0
LEDREF[11:0] (Register output)
000h~0CDh
0CEh~7FFh
800h~FFFh
2
1
0
LEDREF[2]
1
LEDREF[1]
1
LEDREF[0]
0
2
1
0
LEDREF[10]
0
LEDREF[9]
1
LEDREF[8]
0
LED_REF_12~LED_REF_01(to analog)
0CDh
0CEh~7FFh
800h
LED_REF_01 to LED_REF_16 signals to analog are used with the maximum voltage of 1.0V and the minimum voltage of 0.1V,
they are converted with the decoder listed above.
Minimum value (0.1V):
0.1 / 2 * 4095 = 0CDh
Maximum value (1.0V):
1 / 2 * 4095 = 800h
Default value (0.3V):
0.3 / 2 * 4095 = 266h
Note: Reg02h and 03h are synchronized with the leading edge of VSYNC input signal.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
15/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●ADDR=04h
MASKSET (Error signal output mask time setting register: Read/Write)
Bit
Register
Name
Default
7
6
5
4
3
2
-
-
-
-
-
-
-
-
-
-
-
-
Decoder
ERRMSK[1]
0
0
1
1
ERRMSK[0]
0
1
0
1
1
0
ERRMSK[1]
1
ERRMSK[0]
0
ERROR MASK Count Value
02h(2d)
04h(4d)
08h(8d)
10h(16d)
Note: Reg04h is synchronized with the leading edge of the VSYNC signal.
Note: For counting values, a counter that counts one every four HSYNC signals is used.
●ADDR=05h
ERRLEDOPA (LED1 to LED8 ERROR pin monitor: Read)
Bit
7
6
5
Register
Name
Default
ERRLEDOP_04
ERRLEDOP_03
ERRLEDOP_02
ERRLEDOP_01
0
0
0
0
0
0
0
0
4
3
2
1
0
ERRLEDOP_16
ERRLEDOP_15
ERRLEDOP_14
ERRLEDOP_13
ERRLEDOP_12
ERRLEDOP_11
ERRLEDOP_10
ERRLEDOP_09
0
0
0
0
0
0
0
0
4
3
2
1
0
ERRLEDSH_08
ERRLEDSH_07
ERRLEDSH_06
ERRLEDSH_05
ERRLEDSH_04
ERRLEDSH_03
ERRLEDSH_02
ERRLEDSH_01
0
0
0
0
0
0
0
0
4
3
2
1
0
ERRLEDSH_16
ERRLEDSH_15
ERRLEDSH_14
ERRLEDSH_13
ERRLEDSH_12
ERRLEDSH_11
ERRLEDSH_10
ERRLEDSH_09
0
0
0
0
0
0
0
0
4
3
2
1
0
ERRRESSH_08
ERRRESSH_07
ERRRESSH_06
ERRRESSH_05
ERRRESSH_04
ERRRESSH_03
ERRRESSH_02
ERRRESSH_01
0
0
0
0
0
0
0
0
4
3
2
1
0
●ADDR=0Ah
ERRRESSHB (LED9 to LED16 ERROR pin monitor: Read)
Bit
7
6
5
Register
Name
Default
0
ERRLEDOP_05
●ADDR=09h
ERRRESSHA (LED1 to LED8 ERROR pin monitor: Read)
Bit
7
6
5
Register
Name
Default
1
ERRLEDOP_06
●ADDR=08h
ERRLEDB (LED9 to LED16 ERROR pin monitor: Read)
Bit
7
6
5
Register
Name
Default
2
ERRLEDOP_07
●ADDR=07h
ERRLEDSHA (LED1 to LED8 ERROR pin monitor: Read)
Bit
7
6
5
Register
Name
Default
3
ERRLEDOP_08
●ADDR=06h
ERRLEDOPB (LED9 to LED16 ERROR pin monitor: Read)
Bit
7
6
5
Register
Name
Default
4
ERRRESSH_16
ERRRESSH_15
ERRRESSH_14
ERRRESSH_13
ERRRESSH_12
ERRRESSH_11
ERRRESSH_10
ERRRESSH_09
0
0
0
0
0
0
0
0
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
16/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●ADDR=0Bh
ERRMOSSHA (LED1 to LED8 ERROR pin monitor: Read)
Bit
7
6
5
Register
Name
Default
2
1
0
ERRMOSSH_07
ERRMOSSH_06
ERRMOSSH_05
ERRMOSSH_04
ERRMOSSH_03
ERRMOSSH_02
ERRMOSSH_01
0
0
0
0
0
0
0
0
4
3
2
1
0
ERRMOSSH_16
ERRMOSSH_15
ERRMOSSH_14
ERRMOSSH_13
ERRMOSSH_12
ERRMOSSH_11
ERRMOSSH_10
ERRMOSSH_09
0
0
0
0
0
0
0
0
ERR
0
1
ERR monitor
Normal
ERROR
●ADDR=0Dh
DUMMY (Dummy register: Read/Write)
Bit
7
Register
Name
Default
6
5
4
3
2
1
0
DMY08
DMY07
DMY06
DMY05
DMY04
DMY03
DMY02
DMY01
0
0
0
0
0
0
0
0
●ADDR=0Eh
SYSCONFIG (Dummy register: Read/Write)
Bit
7
6
Register
Name
Default
3
ERRMOSSH_08
●ADDR=0Ch
ERRMOSSHB (LED9 to LED16 ERROR pin monitor: Read)
Bit
7
6
5
Register
Name
Default
4
5
4
3
2
1
0
EAMPREFC
EAMPREFB
EAMPREFA
VSYNCDIS
MOSSHDIS
RESSHDIS
LEDSHDIS
LEDOPDIS
0
1
1
0
0
0
0
0
LEDOPDIS
0
1
LED Open Disable control
LED open detection is enabled
LED open detection is disabled
LEDSHDIS
0
1
LED Short Disable control
LED short detection is enabled
LED short detection is disabled
RESSHDIS
0
1
RES Short Disable control
Resistor short detection is enabled
Resistor short detection is disabled
MOSSHDIS
0
1
MOS Short Disable control
MOS short detection is enabled
MOS short detection is disabled
VSNCDIS
0
1
VSYNC Disable control
VSYNC is used
VSYNC is not used
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
17/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
Decoder
EAMPREFC
EAMPREFB
EAMPREFA
EAMP Ref. Voltage Setting
EAMP_DAC_11~EAMP_DAC_01
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0.3V
0.4V
0.5V
0.6V
0.8V
1.0V
1.2V
1.5V
0F5h(245d)
147h(327d)
199h(409d)
1EBh(491d)
28Fh(655d)
333h(819d)
3F7h(999d)
4CCh(1228d)
0
0
0
0
1
1
1
1
DAC output voltages to analog are converted with the decoders listed above.
0.3V: 0.3 / 5 * 4095 = 0F5h
0.4V: 0.4 / 5 * 4095 = 147h
0.5V: 0.5 / 5 * 4095 = 199h
0.6V: 0.6 / 5 * 4095 = 1EBh
0.8V: 0.8 / 5 * 4095 = 28Fh
1.0V: 1.0 / 5 * 4095 = 333h
1.2V: 1.2 / 5 * 4095 = 3F7h
1.5V: 1.5 / 5 * 4095 = 4CCh
Note: Reg09h is synchronized with the leading edge of VSYNC signal.
●ADDR=0Fh
VSYNCREG (VSYNCREG control register: Read/Write)
Bit
7
6
5
Register
Name
Default
4
3
2
1
0
-
-
-
-
-
-
-
VSNC_REG
-
-
-
-
-
-
-
0
VSYNC_REG
VSYNCREG control
0
OFF
1
ON
If VSYNC is not used, the register can be controlled by turning ON/OFF VSYNCREG instead of VSYNC.
●ADDR=10h
SSMASKSET (Soft start mask register: Read/Write)
Bit
7
6
5
Register
Name
Default
4
3
2
1
0
SSMASK[7]
SSMASK[6]
SSMASK[5]
SSMASK[4]
SSMASK[3]
SSMASK[2]
SSMASK[1]
SSMASK[0]
0
0
0
0
1
1
0
0
This register is used to make mask section setting (in sync with VSYNC) for the startup of power supply.
●ADDR=11Ch
DTYCNT01L (LED1 PWM duty setting register - Low 8 bits -: Read/Write)
Bit
7
6
5
4
Register
Name
Default
3
2
1
0
DTY01[7]
DTY01[6]
DTY01[5]
DTY01[4]
DTY01[3]
DTY01[2]
DTY01[1]
DTY01[0]
0
0
0
0
0
0
0
0
●ADDR=12h
DTYCNT01M (LED1 PWM duty setting register - High 4 bits -: Read/Write)
Bit
7
6
5
4
3
2
1
0
Register
Name
Default
-
-
-
-
DTY01[11]
DTY01[10]
DTY01[9]
DTY01[8]
-
-
-
-
0
0
0
0
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
18/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
This register is used to make setting of pulse duty for PWM light modulation in a total of 12 bits, i.e., Bit7-0 when
ADDR=11h and Bit3-0 when ADDR=12h.
DTY01[11:0]
“0000 0000 0000”
“0000 0000 0001”
“0000 0000 0010”
“0000 0000 0011”
to
“1111 1111 1100”
“1111 1111 1101”
“1111 1111 1110”
“1111 1111 1111”
LED Pulse Width
Normally set to Low (default)
HSYNC 1 clock width
HSYNC 2 clock width
HSYNC 3 clock width
to
HSYNC 4092 clock width
HSYNC 4093 clock width
HSYNC 4094 clock width
HSYNC 4095 clock width
●ADDR=13h~30h
This register is used to make setting of PWM pulse width for LED2 to LED16. The setting procedure is the same as that for
LED1 with ADDR set to 0Ah and 0Bh.
●ADDR=31h
DLYCNT01L (LED1 PWM Delay setting register – Low 8bit-: Read/Write)
Bit
7
6
5
4
3
Register
DLY01[7] DLY01[6] DLY01[5] DLY01[4] DLY01[3]
Name
Default
0
0
0
0
0
●ADDR=32h
DLYCNT01M (LED1 PWM Delay setting register–High 4bit-: Read/Write)
Bit
7
6
5
4
3
Register
-
-
-
-
DLY01[11]
Name
-
-
-
Default
-
0
2
1
0
DLY01[2]
DLY01[1]
DLY01[0]
0
0
0
2
1
0
DLY01[10]
DLY01[9]
DLY01[8]
0
0
0
This register is used to make setting of delay width for PWM light modulation in a total of 12 bits, i.e., Bit7-0 when
ADDR=32h and Bit3-0 when ADDR=2Eh.
DLY01[11:0]
“0000 0000 0000”
“0000 0000 0001”
“0000 0000 0010”
“0000 0000 0011”
to
“1111 1111 1100”
“1111 1111 1101”
“1111 1111 1110”
“1111 1111 1111”
LED Delay Width
Normally set to Low (default)
HSYNC1 clock width
HSYNC 2 clock width
HSYNC 3 clock width
to
HSYNC 4092 clock width
HSYNC 4093 clock width
HSYNC 4094 clock width
HSYNC 4095 clock width
●ADDR=33h~50h
This register is used to make PWM delay width setting for LED2 to LED16. The setting procedure is the same as that for
LED1 with ADDR set to 2Ah and 2Bh.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
19/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
◆Timing chart
●PWM Delay and ON Duty setting procedure
VSYNC
0
1
2
3
5
4
6
4093 4094 4095
0
1
2
HSYNC
Delay
counter
0
1
2
3
4
5
Duty
counter
6
7
8
0
1
2
3
4
5
6
7
8
PWM_OUT_01
Figure 17. Setting for PWM Delay and ON Duty
By making register setting, PWM output delay and ON duty time counts of CH1 to CH16 can be controlled.
The above timing chart shows an example for CH1.
(To make delay time count setting, write 06h in address 2Ch. To make ON duty time count setting, write 07h in address 0Ch.)
The delay counter starts counting after counting three from the leading edge of VSYNC signal. When the counter reaches the
set delay count value (06h), the duty counter will start counting simultaneously when the PWM_OUT_01 signal is set to “H”.
Subsequently, when the duty counter reaches the set duty count value (07h), the PWM_OUT_01 signal will be set to ”L”.
Since then, the said sequence is continuously repeated.
The same control is also carried out for CH2 to CH16.
The delay counter counts up to FFCh. Even if the set value exceeds this maximum value, it will also count up to FFCh.
●oft-start masking function
A value set at address 09h serves as the pulse number of the VSYNC signal and masks the error signal control in the
relevant section.
(Example) When ADDR=09h and DATA=02h:
VSYNC
LED_OP_DET_*
PWM_OUT_*
SSEND
ERROR
*: 01~16
Figure 18. In case of ADDR:09h and DATA:02h
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
20/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
● ERROR control
There are the following four types of ERROR detection signals:
(1) LED OPEN, (2) LED SHORT, (3) REGISTER SHORT, and (4) MOS SHORT
The following section shows timing charts with the setting below:
(Example) DLY01[11:0]=005h
DTY01[11:0]=2FDh
PMWMSK[1:0]=0h (PMW mask count value: 02h)
ERRMSK[1:0]=0h (ERR MASK count value: 02h)
SSMSK[7:0]=01h
①~③
HSYNC
HSYNC4I
VSYNC
PWM_OUT_01
*LED_OP_DET_01
SSEND
ERROR
pwm_mskcnt[5:0]
3F
err_mskcnt[5:0]
3F
3F
3F
3F
3F
3F
00
3F
A
A
Enlarged chart
拡大図
B
*②、③も同様
Note: Apply the same chart for signals (2) and (3).
HSYNC
HSYNC4I
D
VSYNC
PWM_OUT_01
LED_OP_DET_01
C
Error
detected
ERROR検出
SSEND
ERROR signal detected
I
ERROR
E
pwm_mskcnt[5:0]
F
0
1
2
err_mskcnt[5:0]
3
4
5
0
1
2
G
B
6
7
8
9
0A
0B
3
4
5
6
7
8
H
Enlarged chart
拡大図
HSYNC
HSYNC4I
VSYNC
PWM_OUT_01
ERROR signal is not detected
LED_OP_DET_01
undetected
J Error
ERROR未検出
SSEND
K
ERROR
pwm_mskcnt[5:0]
0
1
2
3
4
5
6
7
8
9
0A
0B
0
err_mskcnt[5:0]
Figure 19-1. Timing Chart for Error detection 1
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
21/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
④
HSYNC
HSYNC4I
VSYNC
PWM_OUT_01
RES_SH_DET_01
SSEND
ERROR
pwm_mskcnt[5:0]
3F
err_mskcnt[5:0]
3F
3F
3F
3F
3F
3F
3F
3F
00
L
M
L
Enlarged chart
拡大図
HSYNC
HSYNC4I
VSYNC
PWM_OUT_01
RES_SH_DET_01
SSEND
ERROR
pwm_mskcnt[5:0]
00
01
02
err_mskcnt[5:0]
M
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
00
01
02
03
04
05
06
07
08
09
0A
0B
Enlarged chart
拡大図
HSYNC
HSYNC4I
VSYNC
PWM_OUT_01
RES_SH_DET_01
SSEND
ERROR
pwm_mskcnt[5:0]
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
00
err_mskcnt[5:0]
Figure 19-2. Timing Chart for Error detection 2
[Operation]
The pwm_mskcnt counter starts counting from the falling edge of HSYNC4I next to the signal that set LED_OP_01 to
“H”. When the counter reaches the set count (02h), the err_maskcnt counter will start counting. When the counter
reaches the set count (02h), the ERROR output signal will be set to “H”.
Subsequently, the error state is continually monitored at the leading edge of pwm_out_01 and judged as “Error not
detected”. After that, when the pwm_mskcnt counter reaches the set count value, the ERROR output signal will be
set to “L”.
The count numbers of pwm_mskcnt and err_mskcnt for the detection signal (4) are the same as those for the
detection signals (1) to (3).
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
22/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
◆Normal operating mode, Boot sequence
①
②
④
③
By inputting the SPI control signal
before the PWM signal of VSYNC
and HSYNC, LED can be controlled
with register settings.
Figure 20. Starting Sequence for normal operation
When you light the LED by general SPI control, please follow the sequence below.
① Input the power supply of VCC, DVDD.
② Launch the STB from L to H.
③ Write the data to the register by SPI control, then set the LED driver.
④ Input the VSYNC, HSYNC signal which is for PWM dimming.
◆PWM dimming mode, Boot sequence
In BD9267KUT, as process mode, there is a test mode for running the LED driver, even there is no
environment for SPI control. After inputting the power supply of VCC and DVDD, by setting the STB to H, it
can be changed to PWM dimming operation mode achieved by duty control immediately. And the operating
conditions are as below
Power supply:VCC and DVDD are in normal operating range.
・VCC=9.0V~35V、 DVDD=3.0V~3.6V
Settings of LED driver(Default settings of register)
・Set all CHs to ON state (LED 1CH~16CH)
・Setting voltage for LED current(Voltage of S1~S16 pin)
:0.30V
・Reference voltage of error amplifier:0.60V
・Soft start setting:16 count of VSYNC
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
23/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
PWM dimmingoperation mode
②
②
Number of count
Control the PWM operation of
LED output with PWM signal
inputted to VSYNC.
③
※Because the protection
functions are masked, the
lighting by LED abnormal
cannot proceed.
Figure 21. Starting Sequence for PWM dimming1
Settings of PWM dimming operation mode
・VSYNC=PWM dimming signal(Input the pulse signal for PWM dimming to VSYNC.)
・HSYNC=GND(Setting for abnormal detection)
When you use the PWM dimming mode, please follow the sequence below.
①
②
③
Input the power supply of VCC and DVDD.
Launch the STB from L to H.
Input the pulse signal to VSYNC.
PWM dimming operation mode (with abnormol detection function)
Number of count
The abnormal detected CH of LED
will be OFF, after VSYNC pulse
count of 12.
normal
STOP
abnormal
At the same time, ERR_DET output
to ERROR
(“ERRDET=L” is abnormal)
Figure 22. Starting Sequence for PWM dimming2
Setting of PWM dimming
・ VSYNC: PWM dimming signal (To input a pulse for PWM dimming to VSYNC pin)
・ HSYNC: 4096 counts during 1cycle of VSYNC signal
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
24/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
◆Condition for protections
Protection
name
Protection pin
LED OPEN
Dx
LEDSHORT
Dx
RES SHORT
Sx
MOSSHORT
Sx
VCC UVLO
VCC
Detection
Condition
Release Condition
Dx < 0.2V
CHx:EN
PWMx=High
Dx > 5V
(LSP=OPEN)
CHx=EN
PWMx=High
Sx < 0.15
CHx=EN
PWMx=High
Sx>0.15
CHx=EN
PWMx=LOW
VCC<7.3V
Protection Type
Dx > 0.1V
Abnormal detection
ERR_DET signal output
Dx < 5V
(LSP=OPEN)
Abnormal detection
ERR_DET signal output
Sx > 0.15V
Abnormal detection
ERR_DET signal output
Sx < 0.15V
Abnormal detection
ERR_DET signal output
VCC>7.5V
Abnormal detection
ERR_DET signal output
・LED_OPEN protection
When PWMx=HIGH, If Drain pin becomes 0.1V(typ) or lower, ERR_DET = LOW is outputted and LED OPEN error will be
detected.
(internal)
Figure 23. LED OPEN Protection
① When PWMx=HIGH, LED OPEN error is detected. ERR_DET=LOW is outputted.
If drain pin voltage is release condition, ERR_DET=HIGH is outputted.
② When PWMx=LOW, LED OPEN error is not detected.
③ When PWMx=HIGH, LED OPEN error is detected. When PWMx=LOW, If drain pin voltage is release condition,
ERR_DET output keep-hold.
・LED_SHORT protection
When PWMx=HIGH, If Drain pin becomes 5V(typ) or more (LSP=OPEN), ERR_DET = LOW is outputted and LED SHORT
error will be detected.
(internal)
Figure 24. LED SHORT Protection
① When PWMx=HIGH, LED SHORT error is detected. ERR_DET=LOW is outputted.
If drain pin voltage is released, ERR_DET=HIGH is outputted.
② When PWMx=LOW, LED SHORT error is not detected.
③ When PWMx=HIGH, LED SHORT error is detected. When PWMx=LOW, even though the drain pin voltage is
realeased, ERR_DET output is kept.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
25/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
・RESISTOR SHORT protection
・MOSFET SHORT protection
When PWMx=HIGH, if the voltage of Source pin becomes lower than 0.15V(typ), ERR_DET = LOW is outputted and RES
SHORT error will be detected, and this error state is realeased when the voltage of Sourse pin comes back to 0.15V(typ) or
higher.
When PWMx=LOW, if the voltage of Source pin becomes higher than 0.15V(typ), ERR_DET = LOW is outputted and RES
SHORT error will be detected, and this error state is realeased when the voltage of Sourse pin comes back to 0.15V(typ) or
lower.
(internal)
Figure 25. RESISTER SHORT Protection and MOSFET SHORT Protection
① When PWMx=LOW, If Source pin becomes 0.15V(typ) or more, MOS SHORT error is detected.
ERR_DET=LOW is outputted.
② If source pin voltage is release condition, ERR_DET=HIGH is outputted.
③ When PWMx=HIGH, If Source pin becomes 0.15V(typ) or lower, RES SHORT error is detected.
ERR_DET=LOW is outputted.
④ If source pin voltage is release condition, ERR_DET=HIGH is outputted.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
26/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Precautions in use
1.) This product is produced with strict quality control, but might be destroyed if used beyond its absolute maximum ratings including
the range of applied voltage or operation temperature. Failure status such as short-circuit mode or open mode can not be
estimated. If a special mode beyond the absolute maximum ratings is estimated, physical safety countermeasures like fuse
needs to be provided.
2.) The circuit functionality is guaranteed within of ambient temperature operation range as long as it is within recommended
operating range. The standard electrical characteristic values cannot be guaranteed at other voltages in the operating ranges,
however the variation will be small.
3.) When this product is installed on a printed circuit board, attention needs to be paid to the orientation and position of IC. Wrong
installation may cause damage to IC. Short circuit caused by problems like foreign particles entering between outputs or
between an output and power GND also may cause damage.
4.) The pin connected a connector need to connect to the resistor for electrical surge destruction.
5.) Use in a strong magnetic field may cause malfunction.
6.) Thermal design needs to be done with adequate margin in consideration of allowable loss (Pd) in actual operation state.
7.) This IC includes temperature protection circuit (TSD circuit). Temperature protection circuit (TSD circuit) strictly aims blockage of
IC from thermal runaway, not protection or assurance of IC. Therefore use assuming continuous use and operation after this
circuit is worked needs to not be done.
8.) This IC is a monolithic IC which has P+ isolation for separation of elements and P board between elements.
A P-N junction is formed in this P layer and N layer of elements, composing various parasitic elements.
For example, a resistance and transistor are connected to a terminal as shown in the figure,
○
When GND>(Terminal A) in the resistance and when GND>(Terminal B) in the transistor (NPN), P-N junction operates
as a parasitic diode.
○
When GND>(Terminal B) in the transistor (NPN), parasitic NPN transistor operates in N layer of other elements nearby
the parasitic diode described before.
Parasitic elements are formed by the relation of potential inevitably in the structure of IC. Operation of parasitic elements can
cause mutual interference among circuits, malfunction as well as damage. Therefore such use as will cause operation of
parasitic elements like application of voltage on the input terminal lower than GND (P board) need to not be done.
B
P
(Terminal B)
~
(Terminal A)
P
+
N
N
C
~
Transistor (NPN)
Resistance
E
GND
N
P
P+
+
N
P
P+
+
N
N
P board
N
P board
GND
GND
Parasitic element
Parasitic element
(Terminal B)
(Terminal A)
Parasitic element
GND
B
C
B
E
GND
Parasitic element
Figure 26.Example of simple structure of monolithic IC
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
27/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
BD9267KUT
●Ordering Information
B
D
9
2
6
7
K
Product name
U
T
Package
KUT:TQFP64U
-
XX
Packaging and forming
XX: Please confirm the formal name
To our sales
●Physical Dimension Tape and Reel Information
TQFP64U
<Tape and Reel information>
9.0±0.3
7.0±0.2
33
49
32
64
17
Container
Tray (with dry pack)
Quantity
1000pcs
Direction of feed Direction of product is fixed in a tray
7.0±0.2
9.0±0.3
48
16
0.1±0.1
0.125±0.1
1.0±0.1
1.2Max.
1
0.5
1pin
0.15±0.1
0.4
0.08
∗ Order quantity needs to be multiple of the minimum quantity.
(Unit : mm)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
28/28
TSZ02201-0F1F0C100050-1-2
03.Aug.2012 Rev.001
Datasheet
Notice
●General Precaution
1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2) All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
●Precaution on using ROHM Products
1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
2)
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3)
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4)
The Products are not subject to radiation-proof design.
5)
Please verify and confirm characteristics of the final or mounted products in using the Products.
6)
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7)
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8)
Confirm that operation temperature is within the specified range described in the product specification.
9)
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Datasheet
●Precaution for Mounting / Circuit board design
1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2)
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
●Precautions Regarding Application Examples and External Circuits
1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2)
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
●Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
●Precaution for Storage / Transportation
1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2)
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3)
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4)
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
●Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
●Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
●Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
●Precaution Regarding Intellectual Property Rights
1) All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2)
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Datasheet
●Other Precaution
1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
2)
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
3)
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
4)
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
5)
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.