Noise Suppression Products/EMI Suppression Filters > EMIFILr (Capacitor type) > Single Circuit Type for Signal Lines Data Sheet EMIFILr (Capacitor type) 1 Single Circuit Type for Signal Lines NFM21C Series (0805 Size) ■ Dimensions ■ Insertion Loss Characteristics (Main Items) 0.3±0.2 (50Ω - 50Ω) 0.85±0.1 0 Insertion Loss (dB) 20 0.6±0.2 2.0±0.2 1.25±0.1 (2) NFM21CC220U1H3 40 NFM21CC470U1H3 NFM21CC101U1H3 60 NFM21CC221R1H3 NFM21CC471R1H3 (1) NFM21CC223R1H3 80 (3) NFM21CC222R1H3 0.2+0.2 –0.1 NFM21CC102R1H3 (2) 100 : Electrode 1 10 (in mm) ■ Equivalent Circuit 100 Frequency (MHz) 1000 2000 ■ Packaging (1) Input Code Packaging Minimum Quantity D 180mm Paper Tape 4000 B Bulk(Bag) 500 Output (3) No polarity. GND (2) ■ Rated Value (p: packaging code) Capacitance Rated Current Rated Voltage Insulation Resistance (min.) Operating Temperature Range 22pF+20%-20% 700mA 50Vdc 1000M ohm -55°C to +125°C NFM21CC470U1H3p 47pF+20%-20% 700mA 50Vdc 1000M ohm -55°C to +125°C NFM21CC101U1H3p 100pF+20%-20% 700mA 50Vdc 1000M ohm -55°C to +125°C NFM21CC221R1H3p 220pF+20%-20% 700mA 50Vdc 1000M ohm -55°C to +125°C NFM21CC471R1H3p 470pF+20%-20% 1000mA 50Vdc 1000M ohm -55°C to +125°C NFM21CC102R1H3p 1000pF+20%-20% 1000mA 50Vdc 1000M ohm -55°C to +125°C NFM21CC222R1H3p 2200pF+20%-20% 1000mA 50Vdc 1000M ohm -55°C to +125°C NFM21CC223R1H3p 22000pF+20%-20% 2000mA 50Vdc 1000M ohm -55°C to +125°C Part Number NFM21CC220U1H3p Number of Circuit: 1 Continued on the following page. o This data sheet is applied for CHIP EMIFILr used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2009.5.1 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > EMIFILr (Capacitor type) > Single Circuit Type for Signal Lines Data Sheet 2 Continued from the preceding page. ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP EMIFILr used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2009.5.1 http://www.murata.com/