FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Features General Description ■ Low On capacitance, 6.0pF (typical) The FSUSB30 is a Low Power, Dual SPST 2-Port Hi-Speed USB 2.0 switch. This part is configured as a single pole, single throw switch and is optimized for switching or isolating a Hi-Speed (480Mbps) source or a Hi-Speed and Full Speed (12Mbps) source. The FSUSB31 is compatible with the requirements of USB2.0 and features an extremely low On Capacitance (CON) of 6.0pF. The wide bandwidth of this device (>720MHz), exceeds the bandwidth needed to pass the 3rd harmonic, resulting in signals with minimum edge and phase distortion. Superior channel-to-channel crosstalk also minimizes interference. ■ Low On resistance, 6.5Ω (typical) ■ Low power consumption (1µA maximum) ■ ■ ■ ■ – 10µA maximum ICCT over and expanded control voltage range (VIN = 2.6V, VCC = 4.3V) Wide -3dB bandwidth, > 720MHz 8K I/O to GND ESD protection Power OFF protection when VCC = 0V, D+ / D- pins can tolerate up to 4.3V Packaged in: – Pb-Free 8-lead MicroPak™ (1.6mm x 1.6mm) – Pb-Free 8-lead US-8 (preliminary) The FSUSB31 contains special circuitry on the D+ / Dpins which allows the device to withstand an overvoltage condition. This device is also designed to minimize current consumption even when the control voltage applied to the OE pin, is lower than the supply voltage (VCC). This feature is especially valuable to Ultra-Portable applications such as cell phones, allowing for direct interface with the General Purpose I/Os of the baseband processor. Other applications include port isolation and switching in portable cell phones, PDAs, digital cameras, printers, and notebook computers. Applications ■ Cell phone, PDA, Digital Camera, and Notebook ■ LCD Monitor, TV, and Set-top Box Ordering Information Order Number Package Number Package Description FSUSB31K8X (Preliminary) MAB08A Pb-Free 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide FSUSB31L8X MAC08A Pb-Free 8-Lead MicroPak, 1.6 mm Wide Pb-Free package per JEDEC J-STD-020B. Application Diagram VCC FSUSB31 D+ USB Connector Base Band Processor or FS USB Controller D– OE HS USB Controller MicroPak is a trademark of Fairchild Semiconductor Corporation. ©2006 Fairchild Semiconductor Corporation FSUSB31 Rev. 1.0.3 1 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch March 2006 Analog Symbol HSD+ HSD– D– 7 6 5 8 4 2 D+ HSD– D– OE GND Control 3 Pin Descriptions D+ OE 1 HSD+ VCC NC Pad Assignments for MicroPak (Top View) Pin Name Description OE Bus Switch Enable D+, D−, HSD+, HSD− Data Ports NC No Connect Pin Assignment for US8 1 8 VCC HSD– 2 7 OE OE Function D– 3 6 HSD+ H Disconnect GND 4 5 D+ L D+, D− = HSD NC Truth Table (Top Through View) 2 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Connection Diagrams The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation.) Symbol VCC Parameter Rating −0.5V to +4.6V Supply Voltage −0.5V to +4.6V Input Voltage(1) VS DC VIN DC Switch Voltage(1) −0.5V to VCC + 0.3V HSD D+, D− −0.5V to +4.6V −50mA DC Input Diode Current DC Output Current 50mA −65°C to +150°C Storage Temperature ESD (Human Body Model) All Pins 7.5kV I/O to GND 8kV Recommended Operating Conditions(2) Symbol Parameter Rating VCC Supply Voltage VIN Control Input Voltage 3.0V to 4.3V 0V to VCC Switch Input Voltage 0V to VCC −40°C to +85°C Operating Temperature Notes: 1. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. DC switch voltage may never exceed 4.6V. 2. Control input must be held HIGH or LOW and it must not float. 3 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Absolute Maximum Ratings (All typical values are @ 25°C unless otherwise specified.) TA = −40˚C to +85˚C Symbol Parameter VIK Clamp Diode Voltage VIH Input Voltage HIGH VCC (V) Conditions IIN = −18mA Min Typ 3.0 3.0 to 3.6 1.3 4.3 1.7 Max Units −1.2 V V VIL Input Voltage LOW 3.0 to 3.6 0.5 IIN Control Input Leakage VIN = 0V to VCC 4.3 −1.0 IOZ OFF State Leakage 0 ≤ HSD ≤ VCC 4.3 IOFF Power OFF Leakage Current (D+, D–) VIN = 0.0V to 4.3V, VCC = 0V 0 RON Switch On Resistance3 VIN = 0.4V, ION = −8mA 3.0 6.5 ∆RON Delta RON4 VIN = 0.4V, ION = −8mA VIN = 0.0V − 1.0V, ION = −8mA 3.0 0.35 Ω 3.0 2.0 Ω 4.3 3 RON Flatness RON Flatness ICC Quiescent Supply Current VIN = 0.0V or VCC, IOUT = 0 Increase in ICC Current per VIN = 2.6V, VCC = 4.3V Control Voltage and VCC Levels ICCT V 0.7 1.0 µA −2.0 2.0 µA -2.0 2.0 µA 10.0 Ω 4.3 1.0 µA 4.3 10.0 µA AC Electrical Characteristics (All typical values are for VCC = 3.3V @ 25°C unless otherwise specified.) TA = −40˚C to +85˚C Symbol Parameter VCC (V) Conditions Min Typ Max Figure Units Number tON Turn On Time, OE to Output VIN = 0.8V, RL = 50Ω, CL = 5pF 3.0 to 3.6 15.0 30.0 ns Figure 8 tOFF Turn OFF Time. OE to Output VIN = 0.8V, RL = 50Ω, CL = 5pF 3.0 to 3.6 12.0 25.0 ns Figure 8 tPD Propagation Delay4 RL = 50Ω, CL = 5pF 3.3 0.25 ns Figure 6 Figure 7 TBBM Break-Before-Make RL = 50Ω, CL = 5pF, VIN = 0.8V 3.0 to 3.6 ns Figure 9 OIRR OFF Isolation (Non-Adjacent) RT = 50Ω, f = 240MHz 3.0 to 3.6 −35.0 dB Figure 12 Xtalk Non-Adjacent Channel Crosstalk RT = 50Ω, f = 240MHz 3.0 to 3.6 −55.0 dB Figure 13 BW −3dB Bandwidth RT = 50Ω, CL = 0pF 3.0 to 3.6 720 MHz Figure 11 RT = 50Ω, CL = 5pF 2.0 6.5 550 Notes: 3. Measured by the voltage drop between Dn, HSD, Dn pins at the indicated current through the switch. On Resistance is determined by the lower of the voltage on the two ports. 4. Guaranteed by characterization. 4 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch DC Electrical Characteristics Symbol Parameter VCC (V) Conditions TA = −40°C to +85°C Min Typ Max Units Figure Number tSK(O) Channel-to-Channel Skew5 CL = 5pF 3.0 to 3.6 50.0 ps Figure 6 Figure 10 tSK(P) Skew of Opposite Transitions of the Same Output5 CL = 5pF 3.0 to 3.6 20.0 ps Figure 6 Figure 10 tJ Total Jitter5 RL = 50Ω, CL = 5pF, tR = tF = 500ps at 480 Mbps (PRBS = 215 − 1) 3.0 to 3.6 200 ps Notes: 5. Guaranteed by design. Capacitance Symbol Parameter Conditions TA = −40°C to +85°C Min Typ Max Units Figure Number CIN Control Pin Input Capacitance VCC = 0V 1.0 pF Figure 15 CON D1n, D2n, Dn ON Capacitance VCC = 3.3, OE = 0V 6.0 pF Figure 14 COFF D1n, D2n OFF Capacitance VCC and OE = 3.3 1.7 pF Figure 15 5 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch USB Hi-Speed Related AC Electrical Characteristics 0 0 -1 -10 Off Isolation (dB) Gain (dB) -2 VCC = 3.3V -20 CL = 0pF VCC = 3.3V -3 -4 -5 -6 -30 -40 -50 -60 -70 -80 -7 -90 -8 -100 1 10 100 1000 10000 1 10 Frequency (MHz) Figure 1. Gain vs. Frequency Crosstalk (dB) 100 1000 Frequency (MHz) 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 Figure 2. OFF Isolation VCC = 3.3V 1 10 100 1000 Frequency (MHz) Figure 3. Crosstalk 6 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Typical Characteristics VON FSUSB31 FSUSB31 IDn(OFF) NC HSD Dn A VIN VIN ION OE OE GND GND GND VS = 0 to VCC VS = 0 or VCC RON = VON / ION Each switch port is tested separately. Figure 4. On Resistance Figure 5. OFF Leakage FSUSB31 D+, D– VIN RS GND tFALL = 500ps tRISE = 500ps HSD 800mV Input: HSD+, HSD– 400mV RL VOUT CL* GND 90% 90% 50% 50% 10% 10% VOE VOH GND Output: D+, D– RL, RS, and CL are functions of the application environment (see AC Electrical tables for specific values). 50% tPLH *CL includes test fixture and stray capacitance. Figure 6. AC Test Circuit Load tPHL Figure 7. Switch Propagation Delay Waveforms (TPD) tFALL = 2.5ns tRISE = 2.5ns VCC 90% Input – OE VCC/2 GND 50% VOL 90% VCC/2 10% 10% VOH 90% 90% Output – VOUT VOL tOFF tON Figure 8. Turn ON / Turn OFF Waveform (TON / TOFF) 7 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Test Diagrams VCC HSDn VO VOUT D+, D– Control Input HSDn RL CL* VCC 50% 0V tR = tF = 2.5ns (10–90%) S Control Input VOUT GND 0.9 x VOUT tD *CL includes test fixture and stray capacitance. Figure 9. Break-before-Make (TBBM) tFALL = 500ps tRISE = 500ps 800mV 90% Input: D+, D– 50% 10% 400mV 10% tFALL = 500ps tRISE = 500ps 800mV 90% Input: HSDn+ HSDn– 50% VOH Output1: HSD1+ HSD1– 90% 50% 10% 400mV 90% 50% 50% 50% VOL 10% tPLH1 tPHL1 50% 50% VOH VOH 50% Output: D+, D– 50% Output1: D2+, D2– VOL VOL tPLH tPHL tPLH2 TSK(P) = | tPHL – tPLH | Pulse Skew, TSK(P) tPHL2 TSK(O) = | tPLH1 – tPLH2 | or | tPHL1 – tPHL2 | Output Skew, TSK(OUT) Figure 10. Switch Skew Tests Network Analyzer FSUSB31 RS VIN VS GND GND VOE GND VOUT GND RS and RT are functions of the application environment (See AC Electrical Tables for specific values). RT GND Figure 11. Bandwidth 8 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch VCC FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Network Analyzer FSUSB31 RS VIN VS GND RT VOE GND GND GND VOUT RT GND OFF-Isolation = 20 Log (VOUT / VIN) GND Figure 12. Channel OFF Isolation NC Network Analyzer FSUSB31 RS VIN VS GND VOE GND RT GND GND GND RS and RT are functions of the application environment (50, 75 or 100Ω) RT VOUT GND Crosstalk = 20 Log (VOUT / VIN) Figure 13. Non-Adjacent Channel-to-Channel Crosstalk Capacitance Meter Dn FSUSB31 Dn OE F = 1MHz OE Capacitance Meter VOE = 0 or VCC F = 1MHz HSDn Figure 14. Channel ON Capacitance VOE = 0 or VCC HSDn Figure 15. Channel OFF Capacitance 9 FSUSB31 Rev. 1.0.3 FSUSB31 www.fairchildsemi.com Tape Format for MircoPak Package Designator Tape Section Number Cavities Cavity Status Cover Tape Status L8X Leader (Start End) 125 (typ) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed Tape Dimension inches (millimeters) 10 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Tape and Reel Specification Tape Size A B C D N W1 W2 W3 8 mm 7.0 (177.8) 0.059 (1.50) 0.512 (13.00) 0.795 (20.20) 2.165 (55.00) 0.331 + 0.059/−0.000 (8.40 + 1.50/−0.00) 0.567 (14.40) W1 + 0.078/−0.039 (W1 + 2.00/−1.00) 11 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Reel Dimension for MircoPak inches (millimeters) FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Physical Dimensions inches (millimeters) unless otherwise noted Pb-Free 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide Package Number MAB08A 12 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch Pb-Free 8-Lead MicroPak, 1.6 mm Wide Package Number MAC08A 13 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx™ FAST® ActiveArray™ FASTr™ Bottomless™ FPS™ Build it Now™ FRFET™ CoolFET™ GlobalOptoisolator™ CROSSVOLT™ GTO™ DOME™ HiSeC™ EcoSPARK™ I2C™ 2 E CMOS™ i-Lo™ EnSigna™ ImpliedDisconnect™ FACT™ IntelliMAX™ FACT Quiet Series™ Across the board. Around the world.™ The Power Franchise® Programmable Active Droop™ ISOPLANAR™ LittleFET™ MICROCOUPLER™ MicroFET™ MicroPak™ MICROWIRE™ MSX™ MSXPro™ OCX™ OCXPro™ OPTOLOGIC® OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerEdge™ PowerSaver™ PowerTrench® QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ RapidConnect™ µSerDes™ ScalarPump™ SILENT SWITCHER® SMART START™ SPM™ Stealth™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TCM™ TinyLogic® TINYOPTO™ TruTranslation™ UHC™ UltraFET® UniFET™ VCX™ Wire™ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILDíS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component is any component of a life 1. Life support devices or systems are devices or support device or system whose failure to perform can systems which, (a) are intended for surgical implant into be reasonably expected to cause the failure of the life the body, or (b) support or sustain life, or (c) whose support device or system, or to affect its safety or failure to perform when properly used in accordance with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I18 14 FSUSB31 Rev. 1.0.3 www.fairchildsemi.com FSUSB31 Low Power Dual SPST Hi-Speed USB 2.0 (480Mbps) Switch TRADEMARKS