Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C http://www.semicon.panasonic.co.jp/en/ 3-ch. LED Driver for illumination FEATURES DESCRIPTION I2C Interface (Slave address is switchable.) AN30259A has 3-ch. LED Driver, suitable for RGB illumination. By synchronous clock function, simultaneous LED turn ON/OFF operation of up to 4 ICs can be achieved. Built-in 3-ch. LED Driver Circuit ( Max Current Selectable [63.75 mA / 31.875 mA / 25.50 mA / 12.75 mA] ) 2.4 MHz OSC APPLICATIONS 12 pin Wafer level chip size package (WLCSP) Mobile Phone Smart Phone PCs Game Consoles Home Appliances etc. TYPICAL APPLICATION TOP VIEW LED CLK Input A1 IREF A2 VCC A3 CLK PWM A4 LED3 B1 AD SEL2 B2 AD SEL1 B3 GND B4 LED2 C1 SDA C2 SCL C3 VDD C4 LED1 10 F 39 k 1 F I2C interface Note) This application circuit is an example. The operation of the mass production set is not guaranteed. Customers shall perform enough evaluation and verification on the design of mass production set. Customers shall be fully responsible for the incorporation of the above application circuit and information in the design of the equipment. Page 1 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit Note VCCMAX 7.0 V *1 VDDMAX 4.6 V *1 Topr –30 to + 85 C *2 Tj – 30 to + 125 C *2 Storage temperature Tstg – 55 to + 125 C *2 Input Voltage Range ADSEL1, ADSEL2, SCL, SDA, CLKPWM – 0.3 to 4.3 V — LED1, LED2, LED3 – 0.3 to 6.5 V — HBM (Human Body Model) 2.0 kV — Supply voltage Operating ambience temperature Operating junction temperature Output Voltage Range ESD Note) This product may sustain permanent damage if subjected to conditions higher than the above stated absolute maximum rating. This rating is the maximum rating and device operating at this range is not guaranteeable as it is higher than our stated recommended operating range. When subjected under the absolute maximum rating for a long time, the reliability of the product may be affected. *1: VCCMAX = VCC, VDDMAX = VDD, the values under the condition not exceeding the above absolute maximum ratings and the power dissipation. *2: Except for operating ambient temperature, operating junction temperature and storage temperature, all ratings are for Ta = 25C. POWER DISSIPATION RATING PACKAGE 12 pin Wafer Level Chip Size Package (WLCSP) JA PD (Ta=25 C) PD (Ta=85 C) 537.1 C /W 0.186 W 0.074 W Note) For the actual usage, please refer to the PD-Ta characteristics diagram in the package specification, supply voltage, load and ambient temperature conditions to ensure that there is enough margin follow the power and the thermal design does not exceed the allowable value. CAUTION Although this IC has built-in ESD protection circuit, it may still sustain permanent damage if not handled properly. Therefore, proper ESD precautions are recommended to avoid electrostatic damage to the MOS gates Page 2 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C RECOMMENDED OPERATING CONDITIONS Parameter Supply voltage range Input Voltage Range Output Voltage Range Note) Symbol Min. Typ. Max. Unit Note VCC 3.1 3.7 6.0 V — VDD 1.7 1.85 3.2 V — ADSEL1, ADSEL2, SCL, SDA, CLKPWM – 0.3 — VDD + 0.3 V *1 LED1, LED2, LED3 – 0.3 — VCC + 0.3 V *1 Voltage values, unless otherwise specified, are with respect to GND. GND is voltage for GND. VDD is voltage for VDD. VCC is voltage for VCC. *1 : ( VDD + 0.3 ) V must not be exceeded 4.6 V. ( VCC + 0.3 ) V must not be exceeded 7 V. Page 3 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C ELECTRICAL CHARACTERISTICS VCC = 3.6 V, VDD = 1.8 V Note) Ta = 25 C 2 C unless otherwise specified. Parameter Symbol Condition Min Limits Typ Max Unit Note Current consumption Current consumption 1 OFF mode ICC1 VDD = 0 V 0 2 A — Current consumption 2 OFF mode ICC2 VDD = 1.8 V 1 5 A — Current consumption 3 LED lighting mode ICC3 ILED1 to 3 = 25.50 mA setting All LED = ON 0.6 1.0 mA — Off time leak current ILEAK Off setting VLED1 to 3 = 6.0 V — — 1.0 A — Minimum setting current value 1 IMIN1 IMAX[1:0] = 01, VLED1 to 3 = 1.0 V 0.05 0.10 0.15 mA — Minimum setting current value 2 IMIN2 IMAX[1:0] = 01, VLED1 to 3 = 1.0 V 0.736 0.80 0.864 mA — Maximum setting current value IMAX IMAX[1:0] = 01, VLED1 to 3 = 1.0 V 23.46 25.50 27.54 mA — Current step ISTEP IMAX[1:0] = 01, VLED1 to 3 = 1.0 V 0.00 0.10 0.18 mA — VSAT IMAX[1:0] = 01, Terminal minimum voltage of LED1 to 3 becoming 85% of the LED current value in 1 V. — 0.2 0.4 V — 12.80 mA setting, VLED1 to 3 = 1.0 V –5 — 5 % — 1.92 2.40 2.88 MHz — LED Driver Minimum voltage for retainable constant current value Error between channels IMATCH Internal oscillator Oscillation frequency fOSC — Page 4 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C ELECTRICAL CHARACTERISTICS (continued) VCC = 3.6 V, VDD = 1.8 V Note) Ta = 25 C 2 C unless otherwise specified. Parameter Symbol Condition Min Limits Typ Max Unit Note SCL, SDA High-level input voltage range VIH1 Voltage which recognized that SDA and SCL are High-level VDD 0.7 — VDD + 0.5 V *1 Low-level input voltage range VIL1 Voltage which recognized that SDA and SCL are Low-level – 0.5 — VDD 0.3 V *1 High-level input current IIH1 VSDA ,VSCL = 1.8 V — 0 1 A — Low-level input current IIL1 VSDA ,VSCL = 0 V — 0 1 A — Low-level output voltage1 (SDA) VOL1H ISDA = 3 mA, VDD > 2 V 0 — 0.4 V — Low-level output voltage2 (SDA) VOL1L ISDA = 3 mA, VDD < 2 V 0 — 0.2 VDD V — SCL clock frequency fSCL — 0 — 400 kHz — High-level input voltage range VIH2 — VDD 0.7 — VDD + 0.2 V — Low-level input voltage range VIL2 — – 0.2 — VDD 0.3 V — Pin pull down resistance value RPD2 — 0.5 1.0 2.0 High-level output voltage VOH2 ICLKPWM = – 2 mA VDD 0.8 — VDD + 0.2 V — Low-level output voltage VOL2 ICLKPWM = 2 mA –0.2 — VDD 0.2 V — CLKPWM M — ADSEL1, ADSEL2 High-level input voltage range VIH3 — VDD 0.7 — VDD + 0.2 V — Low-level input voltage range VIL3 — – 0.2 — VDD 0.3 V — High-level input current IIH3 VADSEL1, 2 = 1.8 V — 0 1 A — Low-level input current IIL3 VADSEL1, 2 = 0 V — 0 1 A — Note)*1: The input threshold voltage of I2C bus (Vth) is linked to VDD (I2C bus I/O stage supply voltage). In case the pull-up voltage is not VDD, the threshold voltage (Vth) is fixed to ((VDD / 2) (Schmitt width) / 2 ) and High-level, Low-level of input voltage are not specified. In this case, pay attention to Low-level (max.) value (VILmax). It is recommended that the pull-up voltage of I2C bus is set to the I2C bus I/O stage supply voltage (VDD). Page 5 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C ELECTRICAL CHARACTERISTICS (continued) VCC = 3.6 V, VDD = 1.8 V Note) Ta = 25 C 2 C unless otherwise specified. Parameter Symbol Condition External PWM operation mode Possible input high pulse width WPWM — Min Limits Typ Max — 2.5 — Unit Note CLKPWM s *2 Note) *2 : Typical design value Page 6 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C ELECTRICAL CHARACTERISTICS (continued) VCC = 3.6 V, VDD = 1.8 V Note) Ta = 25 C 2 C unless otherwise specified. Parameter Symbol Condition Min Limits Typ Max Unit Note I2C bus (Internal I/O stage characteristics) Input voltage hysteresis (1) Vhys1 SCL, SDA hysteresis voltage VDD > 2 V 0.05 VDD — — V *3 Input voltage hysteresis (2) Vhys2 SCL, SDA hysteresis voltage VDD < 2 V 0.1 VDD — — V *3 20 + 0.1Cb — 250 ns *3 Bus capacitance : 10 pF to 400pF IP 6 mA (VOLmax = 0.6 V) IP : Max. sink current Output fall time from VIHmin to VILmax tof Spike pulse width kept down by input filter tsp — 0 — 50 ns *3 I/O pin capacitance Ci — — — 10 pF *3 Notes ) *3 ：These are values checked by design but not production tested. Page 7 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C ELECTRICAL CHARACTERISTICS (continued) VCC = 3.6 V, VDD = 1.8 V Ta = 25 C 2 C unless otherwise specified. Note) Parameter Symbol Condition tHD:STA SCL clock "L" duration SCL clock "H" duration Limits Unit Note Min Typ Max After tHD:STA,. the first clock pulse is generated. 0.6 — — s *3,4 tLOW — 1.3 — — s *3,4 tHIGH — 0.6 — — s *3,4 Recursive "START" condition setting time tSU:STA — 0.6 — — s *3,4 Data hold time tHD:DAT — 0 — 0.9 s *3,4 Data setup time tSU:DAT — 100 — — ns *3,4 SDA, SCL signal rise up time tr — — 300 ns *3,4 SDA, SCL signal fall time tf — — 300 ns *3,4 tSU:STO — 0.6 — — s *3,4 Bus free time between under "STOP" condition and "START" condition tBUF — 1.3 — — s *3,4 Capacitive load for each bus line Cb — — — 400 pF *3,4 Noise margin of each connection device at Low-level VnL — 0.1 VDD — — V *3,4 Noise margin of each connection device at High-level VnH — 0.2 VDD — — V *3,4 I2C bus (Bus line specifications) Hold duration (recursive) Setup time under "STOP" condition 20 + 0.1Cb 20 + 0.1Cb Note) *3: These are values checked by design but not production tested. *4: The timing of Fast-mode devices in I2C-bus is specified as follows. All values referred to VIHmin and VILmax level. SDA tf tLOW tSU;DAT tr SCL S tHD;STA tHD;DAT tHIGH tf tHD;STA tSU;STA Sr tSP tSU;STO tr tBUF P S S : START condition Sr : Repeat START condition P : STOP condition Page 8 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C PIN CONFIGURATION 1 2 3 4 A IREF VCC CLK PWM LED3 B AD SEL2 AD SEL1 GND LED2 C Top View SDA SCL VDD LED1 PIN FUNCTIONS Pin No. Pin name Type Output Description A1 IREF Resistor connection pin for setting constant current value A2 VCC A3 CLKPWM A4 LED3 B1 ADSEL2 Input I2C Interface slave address switch pin 2 B2 ADSEL1 Input I2C Interface slave address switch pin 1 B3 GND Ground Ground pin B4 LED2 Output LED2 output pin C1 SDA Input/Output C2 SCL Input C3 VDD C4 LED1 Power Supply Power supply pin for LED Circuit Input/Output Output Reference clock Input / Output pin PWM signal input pin to control LED brightness by the external pulse signal LED3 output pin I2C interface data Input / Output pin I2C interface clock input pin Power Supply Power supply pin for interface Output LED1 output pin Page 9 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C FUNCTIONAL BLOCK DIAGRAM IREF LED1 LED2 LED3 VCC A1 C4 B4 A4 A2 VDD C3 Current Source Current Source Current Source SCL C2 PWM PWM PWM WaveForm Generator WaveForm Generator WaveForm Generator CLKPWM A3 Buffer SDA C1 B2 ADSEL1 OSC I2C B1 ADSEL2 B3 GND Note) This block diagram is for explaining functions. Part of the block diagram may be omitted, or it may be simplified. Page 10 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION 1. I2C-bus Interface 1) Basic Rules This LSI, I2C-bus, is designed to correspond to the Standard-mode (100 kbps) and Fast-mode(400 kbps) devices in the version 2.1 of NXP's specification. However, it does not correspond to the HS-mode (to 3.4 Mbps). This LSI will be operated as a slave device in the I2C-bus system. This IC will not operate as a master device. The program operation check of this LSI has not been conducted on the multi-master bus system and the mix-speed bus system, yet. The connected confirmation of this LSI to the CBUS receiver also has not been checked. Please confirm with our company if it will be used in these mode systems. The I2C is the brand of NXP. 2) START and STOP conditions A High to Low transition on the SDA line while SCL is High is one such unique case. This situation indicates START condition. A Low to High transition on the SDA line while SCL is High defines STOP condition. START and STOP conditions are always generated by the master. After START condition occurs, the bus will be busy. The bus is considered to be free again a certain time after the STOP condition. START condition STOP condition SDA SCL 3) Transferring Data Every byte put on the SDA line must be 8-bits long. The number of bytes that can be transmitted per transfer is unrestricted. Each byte has to be followed by an acknowledge bit. Data is transferred with the most significant bit (MSB) first. P SDA acknowledgement signal from slave MSB SCL S or Sr 1 START or repeated START condition 2 7 8 9 ACK acknowledgement signal from receiver 1 2 3–8 9 ACK Sr Sr or P STOP or repeated START condition Page 11 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 1. I2C-bus Interface (continued) 4) Data format Slave address can be switched by ADSEL1, ADSEL2 pin connections. The chart on the right shows the slave address of this product. ADSEL2 ADSEL1 Slave address Low (Ground) Low (Ground) 30 h (0110000) Low (Ground) High (VDD) 31 h (0110001) High (VDD) Low (Ground) 32 h (0110010) High (VDD) High (VDD) 33 h (0110011) Write mode 7-bit S 8-bit Slave address Start condition W A 8-bit Sub-address A Data byte A P Stop condition Ack Write mode : 0 Read mode A) When sub-address is not assigned. When data is read without assigning sub-address, it is possible to read the value of sub-address specified in Write mode immediately before. 7-bit 8-bit S Slave address Start condition R A Data byte Ack Read mode : 1 A P Stop condition Ex) When writing data into address and reading data from "01 h" 7-bit Write S Slave address 0 A Sub-address (01h) 7-bit Read S Slave address Slave address Start condition 0 A Sub-address Acknowledge bit Write mode : 0 A Data byte A P 8-bit 1 A B) When specifying sub-address 7-bit 8-bit S 8-bit 8-bit Data byte A P 7-bit A S Slave address Ack Repeated start condition 8-bit 1 A Ack Read mode : 1 Data byte A P Stop condition Sub-address should be assigned first. Page 12 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 1. I2C-bus Interface (continued) 4) Data format (continued) Continuous Write mode When using the continuous Write mode, the most significant bit of Sub address should be set to [1]. 7-bit S 8-bit Slave Address Start Condition W A 8-bit Sub Address A Data Byte A P Stop Condition Ack Write mode : 0 Set most significant bit to [1]. Ex) 05h 85h, 11h 91h Continuous Read mode A) When Sub address is not specified When the most significant bit specified in the last Write mode is [1], it is possible to perform the continuous Read mode operation directly after it. 7-bit 8-bit S Slave Address Start Condition R A Data byte A P Ack Read mode : 1 Stop condition Ex) Case where data is read from Address 01h after data is written to Address 01h 7-bit Write S Slave Address 0 A Sub Address 81h 7-bit Read S Slave Address 8-bit 8-bit A Data Byte 8-bit 8-bit 1 A Data Byte A P A Data Byte A P B) When Sub address is specified Set most significant bit to [1]. 8-bit 7-bit S Slave Address Start Condition 0 A Sub Address Acknowledge Bit Write Mode : 0 A S 7-bit 8-bit Slave Address Ack Repeated Start Condition 1 A Ack Read Mode : 1 Data Byte A P Stop Condition Sub address is specified initially Page 13 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 2．Register map Sub Addr ess R/W Register Name Data D7 D6 D5 D4 D3 D2 D1 D0 00h W SRESET — — — — — — — SRESET 01h R/W LEDON — — LED3ON LED2ON LED1ON 02h R/W SEL 03h R/W LED1CC LED1CC [7:0] 04h R/W LED2CC LED2CC [7:0] 05h R/W LED3CC LED3CC [7:0] 06h R/W LED1SLP SLP1TT2 [3:0] SLP1TT1 [3:0] 07h R/W LED2SLP SLP2TT2 [3:0] SLP2TT1 [3:0] 08h R/W LED3SLP SLP3TT2 [3:0] SLP3TT1 [3:0] 09h R/W LED1CNT1 DUTYMAX1 [3:0] DUTYMID1 [3:0] 0Ah R/W LED1CNT2 DELAY1 [3:0] DUTYMIN1 [3:0] 0Bh R/W LED1CNT3 SLP1DT2 [3:0] SLP1DT1 [3:0] 0Ch R/W LED1CNT4 SLP1DT4 [3:0] SLP1DT3 [3:0] 0Dh R/W LED2CNT1 DUTYMAX2 [3:0] DUTYMID2 [3:0] 0Eh R/W LED2CNT2 DELAY2 [3:0] DUTYMIN2 [3:0] 0Fh R/W LED2CNT3 SLP2DT2 [3:0] SLP2DT1 [3:0] 10h R/W LED2CNT4 SLP2DT4 [3:0] SLP2DT3 [3:0] 11h R/W LED3CNT1 DUTYMAX3 [3:0] DUTYMID3 [3:0] 12h R/W LED3CNT2 DELAY3 [3:0] DUTYMIN3 [3:0] 13h R/W LED3CNT3 SLP3DT2 [3:0] SLP3DT1 [3:0] 14h R/W LED3CNT4 SLP3DT4 [3:0] SLP3DT3 [3:0] LED3MD LED2MD LED1MD IMAX [1:0] IOEN CLKDIR EXTPWM DLYSEL3 DLYSEL2 DLYSEL1 Note) Read value in " —" is [0]. Page 14 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details SRESET Register Name Address R/W mode D7 D6 D5 D4 D3 D2 D1 D0 00 h W — — — — — — — SRESET Default 00 h 0 0 0 0 0 0 0 0 D0 : Software reset pin [0] : Normal condition ( default ) [1] : Reset (Reset all the other register and returns to Low automatically) Page 15 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) Register Name LEDON Address R/W mode D7 D6 D5 D4 D3 D2 D1 D0 01 h R/W — LED3MD LED2MD LED1MD — LED3ON LED2ON LED1ON Default 00 h 0 0 0 0 0 0 0 0 D6 : LED3MD LED3 lighting mode setting [0] : LED3 constant current mode ( default ) [1] : LED3 slope mode D5 : LED2MD LED2 lighting mode setting [0] : LED2 constant current mode ( default ) [1] : LED2 slope mode D4 : LED1MD LED1 lighting mode setting [0] : LED1 constant current mode ( default ) [1] : LED1 slope mode D2 : LED3ON LED3 enable control [0] : LED3 OFF ( default ) [1] : LED3 ON D1 : LED2ON LED2 enable control [0] : LED2 OFF ( default ) [1] : LED2 ON D0 : LED1ON LED1 enable control [0] : LED1 OFF ( default ) [1] : LED1 ON LED1 operation mode D4 D0 LED1MD LED1ON 0 0 OFF 1 0 OFF 0 1 ON (constant current mode) 1 1 ON (slope mode) LED1 operation mode This mode applies to LED2, LED3 operation modes, too. Page 16 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) Register Name Address R/W mode 02 h R/W Default 40 h SEL D7 D6 IMAX [1:0] 0 1 D5 D4 D3 D2 IOEN CLKDIR EXTPWM 0 0 0 D1 DLYSEL3 DLYSEL2 0 D0 DLYSEL1 0 0 D7-6 : IMAX [1:0] Maximum value, Step value setting for current setting [00] : Maximum value 12.75 mA, Step value 0.05 mA [01] : Maximum value 25.50 mA, Step value 0.10 mA ( default ) [10] : Maximum value 31.875 mA, Step value 0.125 mA [11] : Maximum value 63.75 mA, Step value 0.25 mA D5 : IOEN CLKPWM pin enable control [0] : CLKPWM pin invalid ( default ) [1] : CLKPWM pin valid D4 : CLKDIR CLKPWM pin I/O mode setting [0] : CLKPWM pin input mode ( default ) [1] : CLKPWM pin output mode D5 IOEN D4 D3 CLKDIR EXTPWM CLKPWM operation mode (Clock mode/PWM mode) 0 0 or 1 0 or 1 OFF 1 0 or 1 1 External PWM operation mode 1 0 0 External clock input mode 1 1 0 Internal clock output mode D3 : EXTPWM CLKPWM pin PWM mode setting [0] : CLKPWM pin PWM mode invalid ( default ) [1] : CLKPWM pin PWM mode valid D2 : DLYSEL3 Lighting delay time mode setting at LED3 Slope mode [0] : LED3 delay time Max 7.50 s mode ( default ) [1] : LED3 delay time Max 1.86 s mode D1 : DLYSEL2 Lighting delay time mode setting at LED2 Slope mode [0] : LED2 Delay time Max 7.50 s mode ( default ) [1] : LED2 Delay time Max 1.86 s mode D0 : DLYSEL1 Lighting delay time mode setting at LED1 Slope mode [0] : LED1 Delay time Max 7.50 s mode ( default ) [1] : LED1 Delay time Max 1.86 s mode Please refer to the detail explanation of following register DELAY1 for DLYSEL* details. <External PWM operation mode> LED lighting turns ON/OFF by High/Low setting of CLKPWM pin at the time of LED lighting setting. This mode enables LED lighting synchronization with music signal and brightness control by High/Low Duty ratio. <External clock input mode> The reference clock for Slope control is CLKPWM pin. Synchronization with external signals is possible. <Internal clock output mode> Internal reference clock for Slope control is generated via CLKPWM pin. (The output clock will not be available when LED1ON=LED2ON=LED3ON=0.) Synchronized operation can be possible when more than two pieces of this LSI are connected. Page 17 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) LED1CC Register Name Address R/W mode 03 h R/W Default 00 h D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 D2 D1 D0 0 0 0 D2 D1 D0 0 0 0 LED1CC [7 : 0] 0 0 0 0 0 D7-0 : LED1CC [7: 0] Current setting for LED1 constant current output LED2CC Register Name Address R/W mode 04 h R/W Default 00 h D7 D6 D5 D4 D3 LED2CC [7 : 0] 0 0 0 0 0 D7-0 : LED2CC [7: 0] Current setting for LED2 constant current output Register Name Address R/W mode 05 h R/W Default 00 h LED3CC D7 D6 D5 D4 D3 LED3CC [7 : 0] 0 0 0 0 0 D7-0 : LED3CC [7 : 0] Current setting for LED3 constant current output Output current value can be changed by IMAX setting as below. LED*CC [7 : 0] IMAX [1 : 0] D7 D6 D5 D4 D3 D2 D1 D0 00h 01h 10h 11h 0 0 0 0 0 0 0 0 0.000 mA 0.000 mA 0.000 mA 0.000 mA 0 0 0 0 0 0 0 1 0.050 mA 0.100 mA 0.125 mA 0.250 mA 0 0 0 0 0 0 1 0 0.100 mA 0.200 mA 0.250 mA 0.500 mA : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 0.050 mA Step : : 0.100 mA Step : : 0.125 mA Step : : 0.250 mA Step : 1 1 1 1 1 1 1 0 12.700 mA 25.400 mA 31.750 mA 63.500 mA 1 1 1 1 1 1 1 1 12.750 mA 25.500 mA 31.875 mA 63.750 mA Page 18 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) LED1SLP Register Name Address R/W mode 06 h R/W Default 88 h D7 D6 D5 D4 D3 0 D1 D0 SLP1TT1 [3 : 0] SLP1TT2 [3 : 0] 1 D2 0 0 1 0 0 0 Total time of SLOPE operation for LED1 will be set. Please refer to following "4. LED control Slope lighting mode" for the details of slope operation. SLP1TT1 [3 : 0] is set as the chart below shows. SLP1TT1 [3:0] Total time of SLOPE operation 1, 2 0 0 0 0 ( PWM cycle = 53.3 s ) 75 125 0 = 0.0 s 0 0 0 1 ( PWM cycle = 53.3 s ) 75 125 1 = 0.5 s 0 0 1 0 ( PWM cycle = 53.3 s ) 75 125 2 = 1.0 s : : : : : : : : : : : : : 0.5 s Step : 1 1 0 0 ( PWM cycle = 53.3 s ) 75 125 12 = 6.0 s 1 1 0 1 ( PWM cycle = 53.3 s ) 75 125 13 = 6.5 s 1 1 1 0 ( PWM cycle = 53.3 s ) 75 125 14 = 7.0 s 1 1 1 1 ( PWM cycle = 53.3 s ) 75 125 15 = 7.5 s SLP1TT2 [3: 0] is set as the chart below shows. SLP1TT2 [3:0] Total time of SLOPE operation 3, 4 0 0 0 0 ( PWM cycle = 53.3 s ) 75 125 0 = 0.0 s 0 0 0 1 ( PWM cycle = 53.3 s ) 75 125 1 = 0.5 s 0 0 1 0 ( PWM cycle = 53.3 s ) 75 125 2 = 1.0 s : : : : : : : : : : : : : 0.5 s Step : 1 1 0 0 ( PWM cycle = 53.3 s ) 75 125 12 = 6.0 s 1 1 0 1 ( PWM cycle = 53.3 s ) 75 125 13 = 6.5 s 1 1 1 0 ( PWM cycle = 53.3 s ) 75 125 14 = 7.0 s 1 1 1 1 ( PWM cycle = 53.3 s ) 75 125 15 = 7.5 s Page 19 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) LED2SLP Register Name Address R/W mode 07 h R/W Default 88 h D7 D6 D5 D4 D3 0 0 D1 D0 SLP2TT1 [3 : 0] SLP2TT2 [3 : 0] 1 D2 0 1 0 0 0 D3 D2 D1 D0 Total time of Slope operation for LED2 will be set. LED3SLP Register Name Address R/W mode 08 h R/W Default 88 h D7 D6 D5 D4 SLP3TT2 [3 : 0] 1 0 0 SLP3TT1 [3 : 0] 0 1 0 0 0 Total time of Slope operation for LED3 will be set. Please refer to following “ 4. LED control Slope lighting mode ” for the details of slope operation. The Slope setting charts for LED2 and LED3 are the same as the one for LED1 in the previous page. Page 20 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) LED1CNT1 Register Name Address R/W mode 09 h R/W Default F8 h D7 D6 D5 D4 D3 1 1 D1 D0 DUTYMID1 [3 : 0] DUTYMAX1 [3 : 0] 1 D2 1 1 0 0 0 D2 D1 D0 D7-4 : DUTYMAX1 [3 : 0] LED1 at Slope lighting maximum PWM Duty setting D3-0 : DUTYMID1 [3 : 0] LED1 at Slope lighting middle PWM Duty setting LED1CNT2 Register Name Address R/W mode 0A h R/W Default 00 h D7 D6 D5 0 0 0 0B h R/W Default 88 h DUTYMIN1 [3 : 0] 0 0 0 0 0 D2 D1 D0 LED1 starting delay time setting LED1 at Slope lighting minimum PWM Duty setting Register Name R/W mode D3 DELAY1 [3 : 0] D7-4 : DELAY1 [3 : 0] D3-0 : DUTYMIN1 [3 : 0] Address D4 LED1CNT3 D7 D6 D5 D4 D3 SLP1DT1 [3 : 0] SLP1DT2 [3 : 0] 1 0 0 0 1 0 0 0 D1 D0 D7-4 : SLP1DT2 [3 : 0] LED1 slope lighting, the period of SLOPE operation 2 time D3-0 : SLP1DT1 [3 : 0] LED1 slope lighting, the period of SLOPE operation 1 time Register Name Address R/W mode 0C h R/W Default 88 h LED1CNT4 D7 D6 D5 D4 D3 SLP1DT4 [3 : 0] 1 0 0 D2 SLP1DT3 [3 : 0] 0 1 0 0 0 D7-4 : SLP1DT4 [3 : 0] LED1 slope lighting, the period of SLOPE operation 4 time D3-0 : SLP1DT3 [3 : 0] LED1 slope lighting, the period of SLOPE operation 3 time Operation parameter of LED1 SLOPE operation will be set. Please refer to following “ 4. LED control Slope lighting mode ” for the details of slope operation. Page 21 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) DUTYMAX1 [3 : 0] correspond to the following PWM Duty setting as the following chart shows. DUTYMAX1 [3 : 0] Duty setting for PWM operation [6 : 0] D3 D2 D1 D0 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 1 0 0 1 0 0 0 1 0 1 1 1 0 0 1 1 0 0 1 1 1 1 1 ~ ~ 1 1 1 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Duty setting for PWM operation [6 : 0] [0000111] : 7 / 128 = 5.47 % [0001111] : 15 / 128 = 11.72 % [0010111] : 23 / 128 = 17.97 % [0011111] : 31 / 128 = 24.22 % : [1110111] : 119 / 128 = 92.97 % [1111111] : 127 / 128 = 99.22 % DUTYMID1 [3: 0] correspond to the following PWM Duty setting as the following chart shows. DUTYMID1 [3 : 0] Duty setting for PWM operation[6 : 0] D3 D2 D1 D0 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 1 1 1 0 0 1 0 0 0 1 0 1 1 1 0 0 1 1 0 0 1 1 1 1 1 ~ ~ 1 1 1 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Duty setting for PWM operation [6 : 0] [0000000] : 0 / 128 = 0 % [0001111] : 15 / 128 = 11.72 % [0010111] : 23 / 128 = 17.97 % [0011111] : 31 / 128 = 24.22 % : [1110111] : 119 / 128 = 92.97 % [1111111] : 127 / 128 = 99.22 % Page 22 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) DUTYMIN1 [3 : 0] correspond to the following PWM Duty setting as the following chart shows. DUTYMIN1 [3 : 0] Duty setting for PWM operation [6 : 0] D3 D2 D1 D0 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0 0 0 1 0 0 0 1 0 0 0 0 0 0 1 1 0 0 1 1 0 0 0 ~ ~ 1 1 1 0 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 Duty setting for PWM operation [6: 0] [0000000] : 0 / 128 = 0 % [0001000] : 8 / 128 = 6.25 % [0010000] : 16 / 128 = 12.5 % [0011000] : 24 / 128 = 18.75 % : [1110000] : 112 / 128 = 87.5 % [1111000] : 120 / 128 = 93.75 % DELAY1 [3 : 0] is set as the following chart shows. DELAY1 [3 : 0] DLYSEL1 = 0 DLYSEL1 = 1 0 0 0 0 0.00 s 0.000 s 0 0 0 1 0.50 s 0.124 s 0 0 1 0 1.00 s 0.248 s ~ ~ ~ 1 1 1 0 7.00 s 1.736 s 1 1 1 1 7.50 s 1.860 s Page 23 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) SLP1DT1 [3 : 0] is set as the following chart shows. SLP1DT1 [3 : 0] Detention time at each step 0 0 0 0 ( PWM cycle = 53.3 s ) 1 = 53.3 s 0 0 0 1 ( PWM cycle = 53.3 s ) 75 1 = 4.0 ms 0 0 1 0 ( PWM cycle = 53.3 s ) 75 2 = 8.0 ms ~ ~ 1 1 1 0 ( PWM cycle = 53.3 s ) 75 14 = 56.0 ms 1 1 1 1 ( PWM cycle = 53.3 s ) 75 15 = 60.0 ms SLP1DT2 [3 : 0] is set as the following chart shows. SLP1DT2 [3: 0] Detention time at each step 0 0 0 0 ( PWM cycle = 53.3 s ) 1 = 53.3 s 0 0 0 1 ( PWM cycle = 53.3 s ) 75 1 = 4.0 ms 0 0 1 0 ( PWM cycle = 53.3 s ) 75 2 = 8.0 ms ~ ~ 1 1 1 0 ( PWM cycle = 53.3 s ) 75 14 = 56.0 ms 1 1 1 1 ( PWM cycle = 53.3 s ) 75 15 = 60.0 ms SLP1DT3 [3 : 0] is set as the following chart shows. SLP1DT3 [3: 0] Detention time at each step 0 0 0 0 ( PWM cycle = 53.3 s ) 1 = 53.3 s 0 0 0 1 ( PWM cycle = 53.3 s ) 75 1 = 4.0 ms 0 0 1 0 ( PWM cycle = 53.3 s ) 75 2 = 8.0 ms ~ ~ 1 1 1 0 ( PWM cycle = 53.3 s ) 75 14 = 56.0 ms 1 1 1 1 ( PWM cycle = 53.3 s ) 75 15 = 60.0 ms SLP1DT4 [3 : 0] is set as the following chart shows. SLP1DT4 [3: 0] Detention time at each step 0 0 0 0 ( PWM cycle = 53.3 s ) 1 = 53.3 s 0 0 0 1 ( PWM cycle = 53.3 s ) 75 1 = 4.0 ms 0 0 1 0 ( PWM cycle = 53.3 s ) 75 2 = 8.0 ms ~ ~ 1 1 1 0 ( PWM cycle = 53.3 s ) 75 14 = 56.0 ms 1 1 1 1 ( PWM cycle = 53.3 s ) 75 15 = 60.0 ms Page 24 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) LED2CNT1 Register Name Address R/W mode 0D h R/W Default F8 h D7 D6 D5 D4 D3 1 1 D1 D0 DUTYMID2 [3 : 0] DUTYMAX2 [3 : 0] 1 D2 1 1 0 0 0 D2 D1 D0 D7-4 : DUTYMAX2 [3 : 0] LED2 at slope lighting, maximum PWM Duty setting D3-0 : DUTYMID2 [3 : 0] LED2 at slope lighting, middle PWM Duty setting LED2CNT2 Register Name Address R/W mode 0E h R/W Default 00 h D7 D6 D5 D4 D3 DELAY2 [3 : 0] 0 0 0 DUTYMIN2 [3 : 0] 0 0 0 0 0 D2 D1 D0 D7-4 : DELAY2 [3 : 0] LED2 starting delay time setting D3-0 : DUTYMIN2 [3 : 0] LED2 at slope lighting, minimum PWM Duty setting Register Name Address R/W mode 0F h R/W Default 88 h LED2CNT3 D7 D6 D5 D4 D3 SLP2DT2 [3 : 0] 1 0 0 SLP2DT1 [3 : 0] 0 1 0 0 0 D1 D0 D7-4 : SLP2DT2 [3 : 0] LED2 slope lighting, the period of SLOPE operation 2 time D3-0 : SLP2DT1 [3 : 0] LED2 slope lighting, the period of SLOPE operation 1 time Register Name Address R/W mode 10 h R/W Default 88 h LED2CNT4 D7 D6 D5 D4 D3 SLP2DT4 [3 : 0] 1 0 0 D2 SLP2DT3 [3 : 0] 0 1 0 0 0 D7-4 : SLP2DT4 [3 : 0] LED2 slope lighting, the period of SLOPE operation 4 time D3-0 : SLP2DT3 [3 : 0] LED2 slope lighting, the period of SLOPE operation 3 time Operation parameter of LED2 SLOPE operation will be set. Each parameter is the same as LED1 Parameter. Please refer to following “ 4. LED control Slope lighting mode ” for the details of slope operation. Page 25 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 3．Register map details (continued) LED3CNT1 Register Name Address R/W mode 11 h R/W Default F8 h D7 D6 D5 D4 D3 1 1 D1 D0 DUTYMID3 [3 : 0] DUTYMAX3 [3 : 0] 1 D2 1 1 0 0 0 D2 D1 D0 D7-4 : DUTYMAX3 [3 : 0] LED3 at slope lighting maximum PWM Duty setting D3-0 : DUTYMID3 [3 : 0] LED3 at slope lighting middle PWM Duty setting LED3CNT2 Register Name Address R/W mode 12 h R/W Default 00 h D7 D6 D5 D4 D3 DELAY3 [3 : 0] 0 0 0 DUTYMIN3 [3 : 0] 0 0 0 0 0 D2 D1 D0 D7-4 : DELAY3 [3 : 0] LED3 starting delay time setting D3-0 : DUTYMIN3 [3 : 0] LED3 at slope lighting minimum PWM Duty setting Register Name Address R/W mode 13 h R/W Default 88 h LED3CNT3 D7 D6 D5 1 0 0 14 h R/W Default 88 h SLP3DT1 [3 : 0] 0 1 0 0 0 D1 D0 LED3 slope lighting, the period of SLOPE operation 2 time LED3 slope lighting, the period of SLOPE operation 1 time Register Name R/W mode D3 SLP3DT2 [3 : 0] D7-4 : SLP3DT2 [3: 0] D3-0 : SLP3DT1 [3: 0] Address D4 LED3CNT4 D7 D6 D5 D4 D3 SLP3DT4 [3: 0] 1 D7-4 : SLP3DT4 [3: 0] D3-0 : SLP3DT3 [3: 0] 0 0 D2 SLP3DT3 [3: 0] 0 1 0 0 0 LED3 slope lighting, the period of SLOPE operation 4 time LED3 slope lighting, the period of SLOPE operation 3 time Operation parameter of LED3 SLOPE operation will be set. Each parameter is the same as LED1 parameter. Please refer to following “ 4. LED control Slope lighting mode ” for the details of slope operation. Page 26 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 4. LED control Constant current lighting mode It is possible to choose "Constant current lighting mode" and "Slope lighting mode" by setting Register LED*MD. To operate at "Constant current mode", please set LED*MD at "0". ( "*" can be 1, 2, or 3.) Starting delay time Constant current operation LED*MD LED*ON Current value set by LED*CC LED* output current DELAY* Upon setting LED*ON to "1", constant current operation will start after the previously set starting delay time, DELAY*. As described in page 30, it is possible to turn on and off at High/Low of CLKPWM pin by making the external PWM operating mode for CLKPWM pin setting valid. Page 27 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 4. LED control (continued) Slope lighting mode To operate at "Slope lighting mode", please set LED*MD at "1". ( "*" can be 1, 2, or 3.) Starting SLOPE delay time operation 1 SLOPE operation 2 SLOPE SLOPE operation 3 operation 4 SLOPE operation 1 LED*MD LED*ON DUTYMAX* DUTYMID* DUTYMIN* DELAY* SLP*TT2 SLP*TT1 SLP*DT1 SLP*DT2 SLP*DT3 SLP*DT4 SLOPE Operation 1 SLOPE Operation 2 SLOPE Operation 3 SLOPE Operation 4 Detention time To repeat Slope operation from 1 to 4 after the previously set starting delay time, DELAY*, please set Register LED*ON at "1". The minimum resolution of SLOPE sequence control is 2.40 MHz reference clock cycle as below. LED*ON 2.4 MHz reference CLK Current value set at LED*CC[7: 0] LED* output current 128 cycle Duty setting 0 / 128 to 127 / 128 Page 28 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 4. LED control (continued) 1) Total time of Slope operation 1, 2 Total time of Slope operation 1, 2 can be controlled by SLP*TT1[3 : 0]. SLP*TT1[3 : 0] is set as described before. SLP*TT1[3 : 0] setting has priority to the case of SLP*TT1[3 : 0] < "SLOPE operation 1" + "SLOPE operation 2". In case of that SLP*TT1[3 : 0] time is over during SLOPE operation 1 (before SLOPE operation 2), SLOPE operation 2 is omitted and transferred to SLOPE operation 3 from the position of DUTYMAX. 2) Total time of Slope operation 3, 4 Total time of Slope operation 3, 4 can be controlled by SLP*TT2[3: 0]. SLP* TT2[3 : 0] is set as described before. SLP*TT2[3 : 0] setting has priority to the case of SLP*TT2[3 : 0] < "SLOPE operation 3" + "SLOPE operation 4". In case of that SLP*TT2[3 : 0] time is over during SLOPE operation 3(before SLOPE operation 4), SLOPE operation 4 is omitted and transferred to SLOPE operation 1 from the position of DUTYMIN. 3) DUTYMIN, DUTYMID, DUTYMAX setting for SLOPE operation SLOPE operation 1 PWM step increases step by step from the value set by DUTYMIN*[3 : 0] to the value set by DUTYMID*[3 : 0]. Please set the period by SLP*DT1[3 : 0] for each step. The value should be DUTYMIN*[3 : 0] < DUTYMID*[3 : 0]. SLOPE operation 1 operates at DUTYMIN = DUTYMID in case DUTYMIN*[3 : 0] DUTYMID*[3 : 0] . SLOPE operation 2 PWM step increases step by step from the value set by DUTYMID*[3 : 0] to the value set at DUTYMAX*[3 : 0]. Please set the period by SLP*DT2[3 : 0] for each step. The value should be DUTYMID*[3 : 0] < DUTYMAX*[3 : 0]. SLOPE operation 2 operates at DUTYMID = DUTYMAX in case DUTYMID*[3 : 0] DUTYMAX*[3 : 0] . Slope operation 3 PWM step decreases step by step from the value set by DUTYMAX*[3 : 0] to the value set by DUTYMID*[3 : 0]. Please set the period by SLP*DT3[3: 0] for each step. The value should be DUTYMID*[3 : 0] < DUTYMAX*[3 : 0]. SLOPE operation 3 operates at DUTYMID = DUTYMAX in case DUTYMID*[3 : 0] DUTYMAX*[3 : 0] . SLOPE operation 4 PWM step decreases step by step from the value set by DUTYMID*[3 : 0] to the value set by DUTYMIN*[3 : 0]. Please set the period by SLP*DT4[3 : 0] for each step. The value should be DUTYMIN*[3 : 0] < DUTYMID*[3 : 0]. SLOPE operation 4 operates at DUTYMIN = DUTYMID in case DUTYMIN*[3 : 0] DUTYMID*[3: 0] . Page 29 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 4. LED control (continued) 4) External PWM operation mode of CLKPWM pin The lighting synchronization with CLKPWM signal can be turned on by setting "External PWM operation mode" in register setting. The maximum frequency which can be input to CLKPWM pin is 20 kHz. < At Constant current mode > Constant current operation LED*ON CLKPWM (External input) Current value set by LED*CC LED* output current CLKPWM operating mode OFF External PWM operating mode Current waveform synchronized with CLKPWM pin < At Slope lighting mode> Slope operation LED*ON CLKPWM (External input) Current value set to SLOPE setting LED* output current CLKPWM Operating mode OFF External PWM operating mode Current waveform synchronized with CLKPWM pin Page 30 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C OPERATION (continued) 4. LED control (continued) 5) External clock input mode and internal clock output mode of CLKPWM pin The following configuration can be made up by choosing "External clock input mode", "Internal clock output mode“ in register setting. < Single application > VDCDC CLKPWM Unused state（CLKPWM operation OFF mode） < Connected application > Internal clock output mode VDCDC CLKPWM CLKPWM ・・・ Capable of connected operation by using synchronous clock External clock input mode (Please refer to the explanation of the operation mode of P.17 for the setting of CLKPWM) < External reference clock application > VDCDC External oscillator CLKPWM ・・・ Capable of operating using external reference clock External clock input mode (Please refer to the explanation of the operation mode of P.17 for the setting of CLKPWM) Page 31 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C PACKAGE INFORMATION ( Reference Data ) Page 32 of 33 Established : 2012-09-18 Revised : 2013-02-09 Doc No. TA4-EA-06119 Revision. 2 Product Standards AN30259C IMPORTANT NOTICE 1. When using the LSI for new models, verify the safety including the long-term reliability for each product. 2. When the application system is designed by using this LSI, please confirm the notes in this book. Please read the notes to descriptions and the usage notes in the book. 3. Please use this product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Our company shall not be held responsible for any damage incurred as a result of our IC being used by our customers, not complying with the applicable laws and regulations. 4. Pay attention to the direction of LSI. When mounting it in the wrong direction onto the PCB (printed-circuit-board), it might emit smoke or ignite. 5. Pay attention in the PCB (printed-circuit-board) pattern layout in order to prevent damage due to short circuit between pins. In addition, refer to the Pin Description for the pin configuration. 6. Perform a visual inspection on the PCB before applying power, otherwise damage might happen due to problems such as a solder-bridge between the pins of the semiconductor device. Also, perform a full technical verification on the assembly quality, because the same damage possibly can happen due to conductive substances, such as solder ball, that adhere to the LSI during transportation. 7. Take notice in the use of this product that it might be damaged or occasionally emit smoke when an abnormal state occurs such as output pin-VCC short (Power supply fault), output pin-GND short (Ground fault), or output-to-output-pin short (load short). Safety measures such as an installation of fuses are recommended because the extent of the above-mentioned damage and smoke emission will depend on the current capability of the power supply.. 8. This IC is intended to be used for general electronic equipment. Consult our sales staff in advance for information on the following applications: Special applications in which exceptional quality and reliability are required, or if the failure or malfunction of this IC may directly jeopardize life or harm the human body. Any applications other than the standard applications intended. (1) Space appliance (such as artificial satellite, and rocket) (2) Traffic control equipment (such as for automobile, airplane, train, and ship) (3) Medical equipment for life support (4) Submarine transponder (5) Control equipment for power plant (6) Disaster prevention and security device (7) Weapon (8) Others : Applications of which reliability equivalent to (1) to (7) is required Our company shall not be held responsible for any damage incurred as a result of or in connection with the IC being used for any special application, unless our company agrees to the use of such special application. 9. This IC is neither designed nor intended for use in automotive applications or environments unless the specific product is designated by our company as compliant with the ISO/TS 16949 requirements. Our company shall not be held responsible for any damage incurred by customers or any third party as a result of or in connection with the IC being used in automotive application, unless our company agrees to such application in this book. 10. Due to the unshielded structure of this LSI, functions and characteristics of the product cannot be guaranteed under the exposure of light. During normal operation or even under testing condition, please ensure that the LSI is not exposed to light. 11. Please ensure that your design does not have metal shield parts touching the chip surface as the surface potential is GND voltage. 12. Pay attention to the breakdown voltage of this LSI when using. Page 33 of 33 Established : 2012-09-18 Revised : 2013-02-09 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for general applications (such as office equipment, communications equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book. Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with your using the products described in this book for any special application, unless our company agrees to your using the products in this book for any special application. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20100202