H V SC AV ER O M A I S IO P L L A N IA BL S N T E TISP4290T3BJ, TISP4350T3BJ *R o BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS TISP4xx0T3BJ Overvoltage Protector Series MODEM Protection against: -TIA/EIA-IS-968 Type A & B surge -UL 60950, Clause 6. power cross -CSA 22.2 No. 60950, Clause 6. power cross SMB Package (Top View) R 1 Low Differential Capacitance .................................. 23 pF typ. 2 T Ion-Implanted Breakdown Region -Precise and Stable Voltage -Low Voltage Overshoot Under Surge VDRM V(BO) V V ‘4290T3 220 290 ‘4350T3 275 350 Device MDXXCM Device Symbol T Rated for International Surge Wave Shapes IPPSM Wave Shape Standard 2/10 GR-1089-CORE 250 SD4XAA A 8/20 IEC 61000-4-5 250 10/160 TIA/EIA-IS-968 150 10/700 ITU-T K.20/.21/.45 120 9/720 TIA/EIA-IS-968 120 10/560 TIA/EIA-IS-968 100 10/1000 GR-1089-CORE 80 R .............................................. UL Recognized Component Description These devices are designed to limit overvoltages on the telephone line. Overvoltages are normally caused by a.c. power system or lightning flash disturbances which are induced or conducted on to the telephone line. A single device provides 2-point protection and is typically used for the protection of 2-wire telecommunication equipment (e.g. between the Ring and Tip wires for telephones and modems). Combinations of devices can be used for multi-point protection (e.g. 3-point protection between Ring, Tip and Ground). The protector consists of a symmetrical voltage-triggered bidirectional thyristor. Overvoltages are initially clipped by breakdown clamping until the voltage rises to the breakover level, which causes the device to crowbar into a low-voltage on state. This low-voltage on state causes the current resulting from the overvoltage to be safely diverted through the device. The high crowbar holding current prevents d.c. latchup as the diverted current subsides.These protectors are guaranteed to voltage limit and withstand the listed lightning surges in both polarities. After a TIA/EIA-IS-968 (replaces FCC Part 68) Type A surge the equipment can be faulty, provided that the fault mode causes the equipment to be unusable. There are two wave shapes used: 10/160 for longitudinal surges and 10/560 for metallic surges. For modems with a TISP4350T3BJ connected between the Ring and Tip wires (and without overvoltage protection to ground), the longitudinal 10/160 applied to both Ring and Tip will not activate the TISP4350T3BJ, giving an operational pass. The metallic 10/560 is applied between Ring and Tip wires and will operate the TISP4350T3BJ. As the TISP4350T3BJ has a current rating of 100 A, 10/560 it will survive the FCC Part Type A 100 A, 10/560 metallic surge giving an operational pass. How to Order Device TISP4290T3BJ TISP4350T3BJ Package BJ (SMB/DO-214AA J-Bend) Carrier R (Embossed Tape Reeled) *RoHS Directive 2002/95/EC Jan 27 2003 including Annex DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. For Standard Termination Finish Order As For Lead Free Termination Finish Order As TISP4290T3BJR TISP4290T3BJR-S TISP4350T3BJR TISP4350T3BJR-S TISP4xx0T3BJ Overvoltage Protector Series Description (Continued) After a TIA/EIA-IS-968 Type B surge the equipment must be operational. As the TISP4350T3BJ has a current rating of 120 A, it will survive both Type B surges, metallic (25 A, 9/720) and longitudinal (37.5 A, 9/720), giving an operational pass to FCC Part 68 Type B surges. The TIA/EIA-IS-968 B type ringer has voltages of 56.5 V d.c. and up to 150 V rms a.c., giving a peak voltage of 269 V. The TISP4350T3BJ will not clip the B type ringing voltage as it has a high impedance up to 275 V. Absolute Maximum Ratings, TA = 25 °C (Unless Otherwise Noted) Rating Symbol ’4290T3 Repetitive peak off-state voltage (see Note 1) ’4350T3 VDRM Value ±220 ±275 Unit V Non-repetitive peak on-state pulse current (see Notes 1 and 2) 2/10 (Telcordia GR-1089-CORE, 2/10 voltage wave shape) 250 8/20 (IEC 61000-4-5, combination wave generator, 1.2/50 volt age wave shape) 250 10/160 (TIA/EIA-IS-968 (replaces FCC Part 68), 10/160 voltage wave shape) 5/310 (ITU-T K.44, 10/700 voltage wave shape used in K.20/45/21) IPPSM 150 120 5/320 (TIA/EIA-IS-968 (replaces FCC Part 68), 9/720 voltage wave shape) 120 10/560 (TIA/EIA-IS-968 (replaces FCC Part 68), 10/560 voltage wave shape) 100 10/1000 (Telcordia GR-1089-CORE, 10/1000 voltage wave shape) 80 A Non-repetitive peak on-state current (see Notes 1, 2 and 3) 20 ms (50 Hz), full sine wave ITSM 16.7 ms (60 Hz), full sine wave 25 30 A 2.1 1000 s 50 Hz/60 Hz Initial rate of rise of on-s tate current, Linear current ramp, Maximum ramp value < 50 A Junction temperature Storage temperature range di T /dt 500 A/µs TJ -40 to +150 °C Tstg -65 to +150 °C NOTES: 1. Initially, the device must be in thermal equilibrium with TJ = 25 °C. 2. These non-repetitive rated currents are peak values of either polarity. The surge may be repeated after the device returns to its initial conditions. 3. EIA/JESD51-2 environment and EIA/JESD51-3 PCB with standard footprint dimensions connected with 5 A rated printed wiring track widths. Derate current values at -0.61 %/°C for ambient temperatures above 25 °C. Overload Ratings, TA = 25 °C (Unless Otherwise Noted) Rating Symbol Value Unit See Figure 4 Peak overload on-state current, a.c. power line cross tests UL 60950 (see Note 4) IT(OV)M for current A rms versus time NOTE 4: These electrical stress levels may damage the device silicon chip. After test, the pass criterion is either that the device is functional or, if it is faulty, that it has a short circuit fault mode. In the short circuit fault mode, the following equipment is protected as the device is a permanent short across the line. The equipment would be unprotected if an open circuit fault mode developed. DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP4xx0T3BJ Overvoltage Protector Series Recommended Operating Conditions Component Min Series resistor for TIA/EIA-IS-968 (replaces FCC Part 68), 10/160 type A surge survival (T-G or R-G connection) RS Typ Max Unit 2.5 Series resistor for TIA/EIA-IS-968 (replaces FCC Part 68), 10/560 type A surge survival 0 Series resistor for TIA/EIA-IS-968 (replaces FCC Part 68), 9/720 type B surge survival 0 Series resistor for GR-1089-CORE first-level surge survival 5 Series resistor for K.20, K.21 and K.45 1.5 kV, 10/700 surge survival 0 Series resistor for K.20, K.21 and K.45 coordination with a 400 V primary protector 6 Ω Electrical Characteristics, TA = 25 °C (Unless Otherwise Noted) Parameter Test Conditions IDRM Repetitive peak offstate current VD = VDRM V(BO) AC breakover voltage dv/dt = ±250 V/ms, RSOURCE = 300 Ω I(BO) AC breakover current dv/dt = ±250 V/ms, RSOURCE = 300 Ω VT On-state voltage IT = ±5 A, t W = 100 µs IH Holding current IT = ±5 A, di/dt = +/-30 mA/ms dv/dt ID Coff Critical rate of rise of off-state voltage Off-state current Off-state capacitance Min Typ Max Unit TA = 25 °C TA = 85 °C ±5 ±10 µA ‘4290T3 ‘4350T3 ±290 ±350 V ±0.8 A ±3 Linear voltage ramp, Maximum ramp value < 0.85 VDRM A ±5 kV/µs TA = 85 °C VD = ±50 V V ±0.15 ±10 f = 1 MHz, Vd = 1 V rms, VD = 0, f = 1 MHz, Vd = 1 V rms, VD = -1 V 54 48 65 58 f = 1 MHz, Vd = 1 V rms, VD = -2 V 43 52 f = 1 MHz, Vd = 1 V rms, VD = -50 V 20 24 f = 1 MHz, Vd = 1 V rms, VD = -100 V 16 19 Typ Max µA pF Thermal Characteristics Parameter Test Conditions Min EIA/JESD51-3 PCB, 115 TA = 25 °C, (see Note 5) R θJA Junction to free air thermal resistance 265 mm x 210 mm populated line card, 4-layer PCB, IT = ITSM(1000) , TA = 25 °C Unit °C/W 52 NOTE 5: EIA/JESD51-2 environment and PCB has standard footprint dimensions connected with 5 A rated printed wiring track widths. DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP4xx0T3BJ Overvoltage Protector Series Parameter Measurement Information +i Quadrant I IPPSM Switching Characteristic ITSM IT V(BO) VT I(BO) IH VDRM -v IDRM ID VD ID IDRM VD VDRM +v IH I(BO) V(BO) VT IT ITSM I Quadrant III Switching Characteristic IPPSM -i PM4XAG Figure 1. Voltage-Current Characteristic for T and R Terminals All Measurements are Referenced to the R Terminal DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP4xx0T3BJ Overvoltage Protector Series Typical Characteristics NORMALIZED CAPACITANCE vs OFF-STATE VOLTAGE TC4TAA TYPICAL CAPACITANCE ASYMMETRY vs OFF-STATE VOLTAGE TC4TAB 1.0 |Coff(+VD) - C off(-VD) | — Capacitance Asymmetry – pF 1 0.9 TJ = 25 °C Vd = 1 Vrms Capacitance Normalized to VD = 0 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.5 1 2 3 5 10 20 30 VD - Off-state Voltage - V 50 100150 Figure 2. DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. 0.9 0.8 0.7 Vd = 10 mV rms, 1 MHz 0.6 0.5 0.4 0.3 0.2 0.1 Vd = 1 V rms, 1 MHz 0.0 1 2 3 4 51 7 0 VD — Off-state Voltage - V Figure 3. 20 30 40 50 TISP4xx0T3BJ Overvoltage Protector Series Rating and Thermal Information IT(OV)M — Peak Overload On-State Current – A rms PEAK OVERLOAD ON-STATE CURRENT vs CURRENT DURATION TI4MAM 40 35 30 25 2 40 A 100 A s 20 DEVICE WILL CARRY CURRENT OF TESTS 1 THRU 5 CLAUSE 6.4, UL 60950, FOR FULL TEST TIME 15 7A 10 9 8 7 6 5 4 3.5 3 2.5 2 0·01 2.2 A WIRING SIMULATOR 0·1 1 10 t - Current Duration - s 100 1000 Figure 4. Peak Overload On-state Current against Duration DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP4xx0T3BJ Overvoltage Protector Series MECHANICAL DATA Recommended Printed Wiring Land Pattern Dimensions 2.54 (.100) SMB Land Pattern 2.40 (.095) DIMENSIONS ARE: 2.16 (.085) MILLIMETERS (INCHES) MDXX BID Device Symbolization Code Devices will be coded as below. As the device parameters are symmetrical, terminal 1 is not identified. Device Symbolization Code TISP4290T3BJ 4290T3 TISP4350T3BJ 4350T3 Carrier Information For production quantities, the carrier will be embossed tape reel pack. Evaluation quantities may be shipped in bulk pack or embossed tape. Package SMB Carrier Embossed Tape Reel Pack DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. Standard Quantity 3 000 TISP4xx0T3BJ Overvoltage Protector Series MECHANICAL DATA SMB (DO-214AA) Plastic Surface Mount Diode Package This surface mount package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. SMB02 4.06 - 4.57 (.160 - .180) 3. 30 - 3. 94 (.130 - .155) 1 2 Index Mark 2. 00 - 2.40 (.079 - .094) 1. 90 - 2.10 (.075 - .083) 0. 76 - 1.52 (.030 - .060) 0. 10 - 0. 20 (.004 - .008) 1. 96 - 2. 32 (.077 - .091) 5. 21 - 5.59 (.205 - .220) DIMENSIONS ARE: MILLIMETERS (INCHES) MDXXBHG DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP4xx0T3BJ Overvoltage Protector Series MECHANICAL DATA Tape Dimensions SMB02 Package Single-Sprocket Tape 3. 90 - 4.10 (.154 - .161 ) ø 1. 95 - 2.05 (.077 - .081) 1. 50 MIN . (.059) 1. 55 - 1.65 ø (.061 - .065 ) 0. 40 MAX . (.016) 1. 65 - 1.85 (.065 - .073 ) 5. 45 - 5.55 (.215 - .219 ) 11.70 - 12.30 (.461 - .484 ) 8. 20 MAX . (.323) e 0 MIN . 7. 90 - 8.10 (.311 - .319 ) Direction of Feed Cover Tape Carrier Tape Embossment 20 ° 4. 50 MAX . (.177) Maximium component rotation Typical component cavity center line MILLIMETERS DIMENSIONS ARE: (INCHES) Typical component center line NOTES: A. The clearance between the component and the cavity must be within 0.05 mm (.002 in) MIN. to 0.65 mm (.026 in) MAX. so that the component cannot rotate more than 20 ° within the determined cavity. B. Taped devices are supplied on a reel of the following dimensions:Reel diameter: 330 mm ± 3.0 mm (12.99 in ± .118 in) Reel hub diameter 75 mm (2.95 in) MIN. Reel axial hole: 13.0 mm ± 0.5 mm (.512 in ± .020 in) C. 3 000 devices are on a reel. “TISP” is a trademark of Bourns, Ltd., a Bourns Company, and is Registered in U.S. Patent and Trademark Office. “Bourns” is a registered trademark of Bourns, Inc. in the U.S. and other countries. DECEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. MDXXBHH