TA8220HQ TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic TA8220HQ 30W BTL × 2ch Audio Power Amplifier The thermal resistance θj−T of TA8220HQ package designed for low thermal resistance, has high efficiency of heat radiation. The temperature rise of chip can be reduced, and the influence from the degradation of the features due to the temperature rise at the high output can also be reduced. This stereo audio power IC, designed for car audio use, has two built−in channels to reduce the characteristic difference between L and R channels. It also contains output short detection circuit, output clip detection and various kind of protection. Weight: 9.8g (typ.) Features • Low thermal resistance: θj−T = 1.5°C / W (infinite heat sink) • High power: POUT (1) = 30W (typ.) / channel (VCC = 14.4V, f = 1kHz, THD = 10%, RL = 2Ω) : POUT (2) = 26W (typ.) / channel (VCC = 13.2V, f = 1kHz, THD = 10%, RL = 2Ω) : POUT (3) = 19W (typ.) / channel (VCC = 13.2V, f = 1kHz, THD = 10%, RL = 4Ω) • Low distortion ratio: THD = 0.04% (typ.) (VCC = 13.2V, f = 1kHz, POUT = 1W, RL = 4Ω, GV = 50dB) • Low noise: VNO = 0.30mVrms (typ.) (VCC = 13.2V, RL = 4Ω, GV = 50dB, Rg = 0Ω, BW = 20Hz~20kHz) • Built−in stand−by function (with (4)pin set at low, power is turned off.): ISB = 1µA (typ.) • Built−in output short detection circuit ((9)pin: Open collector) • Built−in output clip detection circuit ((1)pin: Open collector) • Built−in various protection circuits Protection circuits: Thermal shut down, Over voltage, Out→VCC short, Out→GND short and Out−Out short. • Operating supply voltage: VCC = 9~18V 1 2006-04-28 TA8220HQ Block Diagram TA8220HQ (GV = 50dB) Caution And Application Method (description is made only on the single channel.) 1. Voltage gain adjustment This IC has the amplifier constructions as shown Fig.1. The pre−amp (amp1) is provided to the primary stage, and the input voltage is amplified by the flat amps, amp3 and amp4 of each channel through the phase amp (amp2). Since the input offset is prevented by pre−amp when VCC is set to on, this circuit can remarkably reduce the pop noise. 2 2006-04-28 TA8220HQ The total closed loop gain GV of this IC can be obtained by expression below when the closed loop voltage gain of amp1 is GV1. R + (Rf + R2 ) G V1 = 20log 1 (dB)LLL (1) R f + R2 The closed loop voltage gain of power amp, amp3 and amp4 is fixed at GV3≒GV4 = 20dB. Therefore, the total closed circuit voltage gain GV is obtained through BTL connection by the expression below. GV = GV1 + GV3 + 6 (dB)………(2) For example, when Rf = 0Ω, GV is obtained by the expressions (1) and (2) as shown below. GV≒24 + 20 + 6 = 50dB The voltage gain is reduced when Rf is increased. (Fig.2) With the voltage gain reduced, since (1) the oscillation stability is reduced, and (2) the pop noise changes when VCC is set to on, refer to the items 3 and 4. 2. Stand−by SW function By means of controlling (4)pin (stand−by terminal) to high and low, the power supply can be set to on and off. The threshold voltage of (4)pin is set at 2.1V (3VBE), and the power supply current is about 1µA (typ.) at the stand−by state. Control voltage of (4)pin: V (SB) Stand−By Power V (SB) (V) On Off 0~2 Off On 3~VCC <Adjustage of stand−by SW> (1) Since VCC can directly be controlled to on / off by the microcomputer, the switching relay can be omitted. (2) Since the control current is microscopic, the switching relay of small current capacity is satisfactory for switching. 3 2006-04-28 TA8220HQ 3. Preventive measure against oscillation For preventing the oscillation, it is advisable to use C4, the condenser of polyester film having small characteristic fluctuation of the temperature and the frequency. The condenser (C6) between input and GND is effective for preventing oscillation which is generated with a feedback signal from a output stage. The resistance R to be series applied to C4 is effective for phase correction of high frequency, and improves the oscillation allowance. (1) Voltage gain to be used (GV setting) (2) Capacity value of condenser (3) Kind of condenser (4) Layout of printed board In case of its use with the voltage gain GV reduced or with the feedback amount increased, care must be taken because the phase−inversion is caused by the high frequency resulting in making the oscillation liable generated. 4. Adjustment of output offset (when the power supply turn on) As this IC is constructed with DC circuit on the pre−amp stage, it is necessary to lower a input offset or output offset by agreement with the each leading edge time constant of the input voltage in the pre−amp stage and NF terminal voltage. Concretely, monitor the output DC voltage and vary the capacity value in input condenser and NF condenser (see Fig.4) (Reference) In case of setting the condition (GV = 40dB) with Rf = 470Ω 4 2006-04-28 TA8220HQ 5. Output clip detection function (pin(1)) The output clip detection terminal of pin(1) has the open collector output structure on clip as shown in Fig.5. In case that the output waveform is clipping, the clip detection circuit is operated and NPN Tr. is turned on. It is possible to improve the tone quality with the current of flowing into pin(1) and with controlling the volume, tone･control circuit through L.P.F smoothing circuit as shown in Fig.5. In case of being unused this function, use this IC as open connection on pin(1). (Application) 5 2006-04-28 TA8220HQ 6. Output to VCC, output to GND detection function (pin(9)) The output short detection terminal of pin(9) has open collector output structure on chip as shown in Fig.6. In unusual case that output terminal of power amp. is condition of output to VCC or output to GND short, it is possible to protect all the system of apparatus as well as power IC protection. In case of being unused this function, use this IC as open−connection on pin(9). 7. External part list and description Sym− bol Recommended Value C1 4.7µF Influence Feature DC blocking Smaller Than Recommended Value Larger Than Recommended Value Related to pop noise at VCC→on. Remarks Related to gain. Refer to item 4. Related to pop noise at VCC→on. C2 47µF Feedback condenser C3 220µF Ripple reduction Time constant is small at VCC→on or off. Time constant is large at VCC→on or off. C4 0.12µF Oscillation prevention Made liable to oscillate. Oscillation allowance Determination of low cut−off frequency 1 C2 = 2π ⋅ fL ⋅ R f C5 1000µF Ripple filter For filtering power supply hum and ripple. Large at using AC rectified power supply. Small at using DC power supply. C6 1000pF Oscillation prevention Oscillation allowance improved. Noise reduction 6 Refer to item 3. Refer to item 3. 2006-04-28 TA8220HQ Absolute Maximum Ratings (Ta = 25°C) Characteristic Symbol Rating Unit VCC (surge) 50 V DC supply voltage VCC (DC) 25 V Operating supply voltage VCC (opr) 18 V Output current (peak) IO (peak) 9 A Power dissipation PD 50 W Operating temperature Topr −30~85 °C Storage temperature Tstg −55~150 °C Peak input voltage (0.2s) Electrical Characteristics (unless otherwise specified, VCC = 13.2V, RL = 4Ω, f = 1kHz, Ta = 25°C) Characteristic Quiescent supply current Output power Total harmonic distortion Voltage gain Voltage gain ratio Symbol Test Cir− cuit ICCQ — POUT (1) POUT (2) Test Condition Min. Typ. Max. Unit VIN = 0 — 120 250 mA — VCC = 14.4V, RL = 2Ω, THD = 10% — 30 — — RL = 2Ω, THD = 10% 17 26 — W POUT (3) — THD = 10% 16 19 — THD — POUT = 1W — 0.04 0.4 % GV — 48 50 52 dB ∆GV — −1.0 0 1.0 dB Output noise voltage VNO — Rg = 0Ω, BW = 20Hz~20kHz — 0.3 0.7 mVrms Ripple rejection ratio R.R. — fripple = 100Hz, Rg = 600Ω 40 54 — dB Input resistance RIN — — 30 — kΩ −100 0 100 mV — 1 10 µA Output offset voltage Voffset — Current at stand−by state ISB — VIN = 0 Cross talk C.T. — Rg = 600Ω, VOUT = 0.775Vrms (0dBm) — 60 — dB (4)pin control voltage VSB — Stand−by→off (power→on) 2.5 — VCC V (1)pin (clip DET) saturation voltage Vsat (1) — IC = 1mA — 100 — mV (9)pin (short DET) saturation voltage Vsat (9) — IC = 1mA — 100 — mV 7 2006-04-28 TA8220HQ Vsat (1), Vsat (9) Test Circuit Test Circuit TA8220HQ (GV = 50dB) 8 2006-04-28 TA8220HQ 9 2006-04-28 TA8220HQ 10 2006-04-28 TA8220HQ 11 2006-04-28 TA8220HQ Package Dimensions Weight: 9.8g (typ.) 12 2006-04-28 TA8220HQ 13 2006-04-28 TA8220HQ • Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. • If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. For details on how to connect a protection circuit such as a current limiting resistor or back electromotive force adsorption diode, refer to individual IC datasheets or the IC databook. IC breakdown may cause injury, smoke or ignition. • Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. • Carefully select external components (such as inputs and negative feedback capacitors) and load components (such as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage to a speaker directly. • Over current Protection Circuit Over current protection circuits (referred to as current limiter circuits) do not necessarily protect ICs under all circumstances. If the Over current protection circuits operate against the over current, clear the over current status immediately. Depending on the method of use and usage conditions, such as exceeding absolute maximum ratings can cause the over current protection circuit to not operate properly or IC breakdown before operation. In addition, depending on the method of use and usage conditions, if over current continues to flow for a long time after operation, the IC may generate heat resulting in breakdown. • Thermal Shutdown Circuit Thermal shutdown circuits do not necessarily protect ICs under all circumstances. If the Thermal shutdown circuits operate against the over temperature, clear the heat generation status immediately. Depending on the method of use and usage conditions, such as exceeding absolute maximum ratings can cause the thermal shutdown circuit to not operate properly or IC breakdown before operation. • Heat Radiation Design When using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. • Installation to Heat Sink Please install the power IC to the heat sink not to apply excessive mechanical stress to the IC. Excessive mechanical stress can lead to package cracks, resulting in a reduction in reliability or breakdown of internal IC chip. In addition, depending on the IC, the use of silicon rubber may be prohibited. Check whether the use of silicon rubber is prohibited for the IC you intend to use, or not. For details of power IC heat radiation design and heat sink installation, refer to individual technical datasheets or IC databooks. 14 2006-04-28 TA8220HQ RESTRICTIONS ON PRODUCT USE 060116EBF • The information contained herein is subject to change without notice. 021023_D • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. 021023_A • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. 021023_B • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 060106_Q • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 021023_C • The products described in this document are subject to the foreign exchange and foreign trade laws. 021023_E • This product generates heat during normal operation. However, substandard performance or malfunction may cause the product and its peripherals to reach abnormally high temperatures. The product is often the final stage (the external output stage) of a circuit. Substandard performance or malfunction of the destination device to which the circuit supplies output may cause damage to the circuit or to the product. 030619_R About solderability, following conditions were confirmed • Solderability (1) Use of Sn-37Pb solder Bath · solder bath temperature = 230°C · dipping time = 5 seconds · the number of times = once · use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath · solder bath temperature = 245°C · dipping time = 5 seconds · the number of times = once · use of R-type flux 15 2006-04-28