S−AU50H TOSHIBA RF POWER AMPLIFIER MODULE S−AU50H UHF BAND FM POWER AMPLIFIER MODULE HAND-HELD TRANSCEIVER Unit in mm MAXIMUM RATINGS (Tc = 25°C) CHARACTERISTIC SYMBOL RATING UNIT DC Supply Voltage VDD 17 V DC Supply Voltage VGG 6 V Input Power Pi 150 mW Output Power Po 12 W Total Current IT 3 A Tc (opr) −30~100 °C Tstg −40~110 °C Operating Case Temperature Range Storage Temperature Range JEDEC EIAJ TOSHIBA Weight: 3.5g — — 5−23E 000707EAA1 · TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. · The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. · The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. · The information contained herein is subject to change without notice. 2001-02-02 1/4 S−AU50H ELECTRICAL CHARACTERISTICS (Tc = 25°C) CHARACTERISTIC Frequency Range SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT frange — 470 — 520 MHz 6.5 — — W 21.1 — — dB Output Power Po Power Gain Gp Total Efficiency Input VSWR Harmonics Load Mismatch Stability ηT VDD = 9.6V, VGG = 4V Pi = 50mW, ZG = ZL = 50Ω 40 — — % VSWRin — — 4.5 — HRM — — −30 dBc — VDD = 15V, Pi = 50mW Po = 7W (VGG = adjust) VSWR LOAD 20 : 1 ALL PHASE No Degradation — — VDD = 7.5~11.5V, VGG = 0~4V Pi = 50mW VSWR LOAD 3: 1 ALL PHASE All spurious output than 60dB below desired signal — CAUTION · This product has intersetting cap. Please pay attention for exceeding stress and foreign matter in your application. And not to take away the cap. · Do not intermingle with normal industrial or domestic waste. · This product is electrostatic sensitivity, please handle with caution. 2001-02-02 2/4 S−AU50H SCHEMATIC TEST FIXTURE 2001-02-02 3/4 S−AU50H CAUTION These are only typical curves and devices are not necessarily guaranteed at these curves. 2001-02-02 4/4