ISL59885 ® Data Sheet May 12, 2009 Auto-Adjusting Sync Separator for HD and SD Video The ISL59885 video sync separator extracts sync timing information from both standard and non-standard video inputs in the presence of Macrovision pulses. The ISL59885 provides horizontal, vertical, and composite sync outputs as well as SD/HDTV detection. An auto input frequency detect feature automatically adapts to a wide range of video standards (it does not need a different RSET resistor for different frequencies). The vertical sync pulse is output on the rising edge of the first vertical serration following the vertical pre-equalizing string. For non-standard vertical inputs, a default vertical pulse is output when the vertical signal stays low for longer than the vertical sync default delay time. The horizontal output gives horizontal timing with pre/post equalizing pulses. Fixed 70mV sync tip slicing provides sync edge detection when the video input level is between 0.5VP-P and 2VP-P. The ISL59885 is available in an 8 Ld SOIC package and is specified for operation over the full -40°C to +85°C temperature range. Pinout FN7442.7 Features • NTSC, PAL, SECAM, HDTV, non-standard video sync separation • Fixed 70mV slicing of video input levels from 0.5VP-P to 2VP-P • Single 3V to 5V supply • Composite sync output • Vertical output • Horizontal output • HDTV detection • Macrovision compatible • Available in 8 Ld SOIC package • Pb-free available (RoHS compliant) Applications • High definition video equipment Demo Board • A dedicated demo board is available ISL59885 (8 LD SOIC) TOP VIEW COMPOSITE SYNC OUT 1 Ordering Information PART NUMBER 8 VDD COMPOSITE VIDEO IN 2 7 HORIZONTAL OUTPUT VERTICAL SYNC OUT 3 6 CSET GND 4 5 HD 1 PART MARKING PACKAGE PKG. DWG. # ISL59885IS* 59885 IS 8 Ld SOIC MDP0027 ISL59885ISZ* (Note) 59885 ISZ 8 Ld SOIC (Pb-free) MDP0027 *Add “-T7” or “-T13” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2005, 2006, 2007, 2009. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ISL59885 Absolute Maximum Ratings (TA = +25°C) Thermal Information VDD Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7V Pin Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VCC +0.5V Operating Ambient Temperature Range . . . . . . . . . .-40°C to +85°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400mW Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. DC Electrical Specifications VDD = 3.3V, TA = +25°C, CSET = 56nF, unless otherwise specified. PARAMETER DESCRIPTION MIN TYP MAX UNIT 1 2.2 4 mA 1.35 1.5 1.65 V IDD, Quiescent VDD = 3.3V Clamp Voltage Pin 2, ILOAD = -100µA Clamp Discharge Current Pin 2 = 2V 6 15 30 µA Clamp Charge Current Pin 2 = 1V -9 -7.2 -5.2 mA VOL Output Low Voltage IOL = 1.6mA 0.24 0.5 V VOH Output High Voltage IOH = -40µA 3 3.2 V IOH = -1.6mA 2.5 3.0 V MIN (Note 1) TYP MAX (Note 1) UNIT Dynamic Characteristics PARAMETER DESCRIPTION Comp Sync Prop Delay, tCS (See Figure 9) 35 75 ns Horizontal Sync Delay, tHS (See Figure 9) 40 80 ns Horizontal Sync Width, tHS-PW (See Figure 9) 3.8 5.2 6.2 µs Vertical Sync Width, tVS Normal or default trigger, 50% to 50% (see Figure 7) 230 280 350 µs Vertical Sync Default Delay, tVSD (See Figure 10) 28 50 68 µs 70 80 90 % 2 VP-P 90 mV Hsync Blanking Window Input Dynamic Range Video input amplitude to maintain slice level spec, VDD = 3.3V 0.5 Slice Level VSLICE above VCLAMP 50 HD Pin Level 720p, 1080i, 1080p 70 0 V NOTE: 1. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 2 FN7442.7 May 12, 2009 ISL59885 Pin Descriptions PIN NUMBER PIN NAME PIN FUNCTION 1 Composite Sync Out Composite sync pulse output; sync pulses start on a falling edge and end on a rising edge. 2 Composite Video In AC coupled composite video input; sync tip must be at the lowest potential (positive picture phase). 3 Vertical Sync Out Vertical sync pulse output; the falling edge of vertical sync is the start of the vertical period. 4 Gnd Supply ground 5 HD Low when input horizontal frequency is greater than 20kHz. 6 CSET 7 Horizontal Output 8 VDD (An external capacitor to ground); bypass pin for internal bias generator. Horizontal output; falling edge active Positive supply Typical Performance Curves VDD = 3.3 AND 5.0V VCSET (V) HSYNC PULSEWIDTH (ns) VDD = 3.3 AND 5.0V k k k k k k k k k k k k k k k k k k k k HSYNC FREQUENCY (Hz) HSYNC (Hz) FIGURE 1. HSYNC vs VCSET (RSET = OPEN) FIGURE 2. HSYNC PULSEWIDTH vs HSYNC FREQUENCY (RSET = OPEN) HSYNC BLANKING TIME (µs) VDD = 3.3 AND 5.0V VIN 0.5V/DIV 5V/DIV HSYNC 5V/DIV VSYNC 5V/DIV CSYNC 100μs/DIV VCSET (V) FIGURE 3. HSYNC vs VCSET (RSET = OPEN) 3 FIGURE 4. MACROVISION COMPATIBILITY (NTSC) FN7442.7 May 12, 2009 ISL59885 Typical Performance Curves (Continued) JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1.8 1.2 POWER DISSIPATION (W) POWER DISSIPATION (W) 1.6 1.4 1.2 1.136W 1.0 θJ SO IC A= +1 8 1 0.8 0°C /W 0.6 0.4 1.0 781mW 0.8 θJ 0.6 A= SO +1 0.4 IC 8 60 °C /W 0.2 0.2 0 0 0 25 50 75 85 100 125 150 0 25 TEMPERATURE (°C) 50 75 85 100 125 150 TEMPERATURE (°C) FIGURE 5. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE FIGURE 6. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE SIGNAL 1a. COMPOSITE VIDEO INPUT, FIELD ONE 1.5µs ±0.1µs TIME VERTICAL BLANKING INTERVAL = 20H 3H H SYNC INTERVAL H 3H 3H 2 3 4 START OF H FIELD ONE PREEQUALIZING PULSE INTERVAL H 1 +H +63.5µs 1271µs -H -0µs 5 6 7 8 9 10 0.5H VERTICAL SYNC PULSE INTERVAL POSTEQUALIZING PULSE INTERVAL 9 LINE VERTICAL INTERVAL 19 20 21 H REF SUBCARRIER PHASE, COLOR FIELD ONE SIGNAL 1b. COMPOSITE SYNC OUTPUT, PIN 1 SIGNAL 1c. VERTICAL SYNC OUTPUT, PIN 3 tVS SIGNAL 1d. HORIZONTAL SYNC OUTPUT, PIN 7 NOTES: 2. The composite sync output reproduces all the video input sync pulses, with a propagation delay. 3. Vertical sync leading edge is coincident with the first vertical serration pulse leading edge with a propagation delay. 4. Horizontal sync output produces the “H” pulses of nominal width of 5µs. It has the same delay as the composite sync. FIGURE 7. TIMING DIAGRAM 4 FN7442.7 May 12, 2009 ISL59885 CONDITIONS: VDD = 3.3V/5V, TA = +25°C WHITE LEVEL COLOR BURST INPUT DYNAMIC RANGE 0.5V TO 2V VIDEO SYNC LEVEL SYNC IN VSLICE 50% SYNC TIP VBLANK (BLANKING LEVEL VOLTAGE) SYNC VSYNC (SYNC TIP VOLTAGE) tdSYNCOUT DEPENDS ON WIDTH OF INPUT SYNC AT 50% LEVEL SYNC OUT tdHOUT HOUT tHOUT FIGURE 8. HORIZONTAL INTERVAL 525/625 LINE COMPOSITE PARAMETER DESCRIPTION CONDITIONS TYP (Note 5) UNIT tdSYNCOUT SYNCOUT Timing Relative to Input (See Figure 8) 65 ns tdHOUT HOUT Timing Relative to Input (See Figure 8) 470 ns tHOUT Horizontal Output Width (See Figure 8) 5.2 µs NOTE: 5. Delay variation is less than 2.5ns over-temperature range. 5 FN7442.7 May 12, 2009 ISL59885 SIGNAL 2a. COMPOSITE VIDEO INPUT SLICE LEVEL 70mV tCS COMP SYNC PROP DELAY SIGNAL 2b. COMPOSITE SYNC OUTPUT tCS-VS COMP SYNC VERT SYNC DELAY SIGNAL 2c. VERTICAL SYNC OUTPUT SIGNAL 2d. HORIZONTAL SYNC OUTPUT tHS tHS-PW FIGURE 9. STANDARD VERTICAL TIMING LINES 2 SIGNAL 3a. COMPOSITE VIDEO INPUT 3 4 5 (NO VERTICAL SYNC PULSES) tVSD VERT SYNC DEFAULT DELAY SIGNAL 3b. VERTICAL SYNC OUTPUT FIGURE 10. NON-STANDARD VERTICAL TIMING 6 FN7442.7 May 12, 2009 ISL59885 COMPOSITE VIDEO INPUT, BEGINNING OF FIELD ONE START OF FIELD ONE 622 623 624 625 1 2 3 4 5 6 7 23 24 SYNCOUT OUTPUT VOUT OUTPUT tVS HOUT OUTPUT NOTES: 6. The composite sync output reproduces all the video input sync pulses, with a propagation delay. 7. Vertical sync leading edge is coincident with the first vertical serration pulse leading edge, with a propagation delay. FIGURE 11. EXAMPLE OF VERTICAL INTERVAL (625) SYNCIN 1123 1124 1125 560 561 562 1 2 3 564 565 4 5 6 567 568 7 8 ... 21 569 570 ... 583 SYNCOUT HOUT VOUT SYNCIN 563 566 SYNCOUT HOUT VOUT FIGURE 12. EXAMPLE OF HDTV 1080I/30 LINE COMPOSITE VIDEO: INTERLACED 7 FN7442.7 May 12, 2009 ISL59885 SYNCIN 1245 1246 1247 1248 1249 1250 620 621 622 623 624 625 1 2 3 4 5 ... 48 SYNCOUT HOUT VOUT SYNCIN 626 627 628 629 630 ... 673 SYNCOUT HOUT VOUT FIGURE 13. HDTV 1080I/25 LINE COMPOSITE VIDEO: INTERLACED (1250 LINES) 8 FN7442.7 May 12, 2009 ISL59885 CONDITIONS: VDD = 3.3V/5V, TA = +25°C SYNCIN tdSYNCOUT SYNC OUT tdHOUT HOUT tHOUT FIGURE 14. HORIZONTAL INTERVAL (HDTV) (720p) H Timing for HDTV, No Filter (using 720p input signal) PARAMETER DESCRIPTION CONDITIONS TYP TYP @ 5V @ 3.3V (Note 8) (Note 8) UNIT tdSYNCOUT SYNCOUT Timing Relative to Input (See Figure 14) 56 50 ns tdHOUT HOUT Timing Relative to Input (See Figure 14) 48 36 ns tHOUT Horizontal Output Width (See Figure 14) 1.90 1.90 µs NOTE: 8. Delay variation is less than 2.5ns over-temperature range. 9 FN7442.7 May 12, 2009 ISL59885 CONDITIONS: VDD = 3.3V/5V, TA = +25°C SYNCIN tdSYNCOUT SYNC OUT tdHOUT HOUT tHOUT FIGURE 15. HORIZONTAL INTERVAL (HDTV) (720p) H Timing for HDTV, With Filter (using 720p input) PARAMETER DESCRIPTION CONDITIONS TYP TYP @ 5V @ 3.3V (Note 9) (Note 9) UNIT tdSYNCOUT SYNCOUT Timing Relative to Input (See Figure 15) 120 110 ns tdHOUT HOUT Timing Relative to Input (See Figure 15) 112 100 ns tHOUT Horizontal Output Width (See Figure 15) 200 200 ns NOTE: 9. Delay variation is less than 2.5ns over-temperature range. 10 FN7442.7 May 12, 2009 ISL59885 Applications Information Video In Refer to the “Simplified Block Diagram” on page 12. An AC coupled video signal is input to Video In pin 2 via C1, nominally 0.1µF. Clamp charge current will prevent the signal on pin 2 from going any more negative than Sync Tip Ref, about 1.5V. This charge current is nominally about 1mA. A clamp discharge current of about 10µA is always attempting to discharge C1 to Sync Tip Ref, thus charge is lost between sync pulses that must be replaced during sync pulses. The droop voltage that will occur can be calculated from IT = CV, where V is the droop voltage, I is the discharge current, t is the time between sync pulses (sync period-sync tip width), and C is C1. An NTSC video signal has a horizontal frequency of 15.73kHz, and a sync tip width of 4.7µs. This gives a period of 63.6µs and a time t = 58.9µs. The droop voltage will then be V = 5.9mV. This is less than 2% of a nominal sync tip amplitude of 286mV. The charge represented by this droop is replaced in a time given by t = CV/I, where I = clamp charge current = 5.3mA. Here t = 590ns, about 12% of the sync pulse width of 4.7µs. It is important to choose C1 large enough so that the droop voltage does not approach the switching threshold of the internal comparator. Composite Sync The Composite Sync output is simply a reproduction of the input signal with the active video removed. The sync tip of the Composite video signal is clamped to 1.5V at pin 2 and then slices at 70mV above the sync tip reference. The output signal is buffered out to pin 1. When loss of sync, the Composite Sync output is held low. MacroVision copy protection. When there is a loss of incoming composite sync, the Horizontal Sync output is held high. CSET An external CSET capacitor connected from CSET pin 6 to ground. CSET capacitor should be a X7R grade or better as the Y5U general use capacitors may be too leaky and cause faulty operation. The CSET capacitor should be very close to the CSET pin to reduce possible board leakage. 56nF is recommended. Refer to the “CSET Bias Block” on page 12. The CSET capacitor rectifies a 5µs pulse current and creates a voltage on CSET. The CSET voltage is converted to bias current for HSYNC and VSYNC timing. Chroma Filter A chroma filter is suggested to increase the S/N ratio of the incoming video signal. Use of the optional chroma filter is shown in Figure16. It can be implemented very simply and inexpensively with a series resistor of 100Ω and a capacitor of 570pF, which gives a single pole roll-off frequency of about 2.79MHz during NTSC or PAL. This sufficiently attenuates the 3.58MHz (NTSC) or 4.43MHz (PAL) color burst signal, yet passes the approximately 15kHz sync signals without appreciable attenuation. During HDTV, the transistor turns off and a 100pF capacitor is left to filter any noise present at the input. A chroma filter will increase the propagation delay from the composite input to the outputs. VIDEO IN RF 0.1µF 1 CSYNC VDD 8 2 HOUT 7 3 VSYNC CSET 6 4 5 CVIN 100Ω CF 100pF Vertical Sync A low-going Vertical Sync pulse is output during the start of the vertical cycle of the incoming video signal. The vertical cycle starts with a pre-equalizing phase of pulses with a duty cycle of about 93%, followed by a vertical serration phase that has a duty cycle of about 15%. Vertical Sync is clocked out of the ISL59885 on the first rising edge during the vertical serration phase. In the absence of vertical serration pulses, a vertical sync pulse will be forced out after the vertical sync default delay time, approximately 60µs after the last falling edge of the vertical equalizing phase. ISL59885 CHROMA FILTER CF2 470pF GND HD 10kΩ MMBT3904 FIGURE 16. OPTIONAL CHROMA FILTER HD-Detect High definition video is flagged by HD going low when the input horizontal frequency is greater than 20kHz. Horizontal Sync The horizontal block senses the leading edges of the composite sync signal and generates horizontal pulses of nominal width 5.2µs. Any half line pulses present in the input signal during vertical blanking are removed with an internal 2H line eliminator function that inhibits the retriggering of horizontal output pulses until 70% of the line time is reached, then the horizontal output operation is enabled again. Any signals present on the I/P signal after the real H sync will be ignored, thus the horizontal output will not be affected by 11 FN7442.7 May 12, 2009 ISL59885 Simplified Block Diagram CLAMP SYNC TIP REF 1.5V C1 RF 620Ω CF 510pF VDD 8 VDD 5V C2 0.1µF COMPOSITE VIDEO IN 2 SLICE 1.57V 0.1µF COMP. + 1 COMPOSITE SYNC GND 4 CSET C3 56nF 6 REF GEN SYNC TIP 70mV SLICE HD DETECTOR 5 HD V SYNC 3 VERTICAL SYNC OUT H SYNC 7 HORIZONTAL SYNC OUT 2H ELIMINATOR CSET Bias Block VDD CSYNC PULSE 5µs VDD CSET 56nF + IBIAS - TIMING All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 12 FN7442.7 May 12, 2009 ISL59885 Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 13 FN7442.7 May 12, 2009