JDP2S05FS TOSHIBA Diode Silicon Epitaxial PIN Type JDP2S05FS Unit:mm UHF~VHF Band RF Switch Applications • Low series resistance: rs = 1.5 Ω (typ.) • Low capacitance: CT = 0.32 pF (typ.) 0.6±0.05 A Symbol Rating Unit Reverse voltage VR 20 V Forward current IF 50 mA Power dissipation(Note:1) Pd 150 mW Junction temperature Tj 150 °C Tstg −55~150 °C Storage temperature range Note: 0.1 0.8±0.05 0.2 ±0.05 0.1 Characteristics 0.07 M A Absolute Maximum Ratings (Ta = 25°C) 1.0±0.05 Suitable for reducing set’s size as a result from enabling high-density mounting due to 2-pin small packages. CATHODE MARK • 0.1±0.05 +0.02 0.48 -0.03 ― JEDEC ― JEITA 1-1L1A TOSHIBA Weight: 0.0006 g(Typ.) Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: When mounted on glass epoxy board board size : 20mm × 20mm × 1.6mmt Cu foot area : 4mm × 4mm × 0.035mmt Electrical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Min Typ. Max Unit Reverse voltage VR IR = 0.1μA 20 ― ― V Reverse current IR VR = 20 V ― ― 0.1 μA Forward voltage VF IF = 50 mA ― ― 0.94 V Capacitance(Note2) CT VR = 1 V, f = 1 MHz 0.21 0.32 0.42 pF Series resistance rs IF = 1 mA, f = 100 MHz ― 1.5 2.2 Ω Note2: Signal level when capacitance is measured. Vsig = 100 mVrms Marking 3 1 2007-11-01 JDP2S05FS TYPICAL PERFORMANCE CURVES (Ta = 25°C) Cs - f 1.8 0.45 1.6 0.40 SERIES CAPACITANCE Cs(pF) SERIES rs rs(Ω) (Ω ) SERIESRESISTANCE RESISTANCE rs - f 1.4 1.2 1.0 0.8 0.6 IF=1mA 0.4 IF=3mA IF=10mA 0.2 0.35 0.30 0.25 0.20 0.15 0.10 VR=0V 0.05 0.0 0.00 0 1000 2000 3000 4000 0 1000 FREQUENCY f(MHz) 2000 Ls - f 4000 Ct - VR 1.0 1 TERMINAL CAPACITANCE Ct(pF) 0.9 SERIES INDUCTANCE Ls(nH) 3000 FREQUENCY f(MHz) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 f = 1MHz Vsig = 100mVrms IF=10mA 0.1 0.1 0.001 0.0 0 1000 2000 3000 4000 0.01 0.1 1 10 100 REVERSE VOLTAGE VR(V) FREQUENCY f(MHz) Switching recovery characteristic IF - VF 1 15 0.01 FORWARD CURRENT IF(mA) FORWARD CURRENT IF(A) 0.1 0.001 0.0001 1E-05 1E-06 1E-07 1E-08 1E-09 10 5 0 -5 IF = 10mA(ON state) VR = 0V(OFF state) RL = Rs = 50Ω -10 1E-10 1E-11 -15 0 0.2 0.4 0.6 0.8 1 1.2 FORWARD VOLTAGE VF(V) 0 2 4 6 8 10 TIME T(μs) 2 2007-11-01 JDP2S05FS PD - Ta MAXIMAM POWER DISSIPATION PD(max) (mW) 160 When mounted on glass epoxy board board size : 20mm× 20mm × 1.6mmt Cu foot area : 4mm × 4mm × 0.035mmt 140 120 100 80 60 40 20 0 0 50 100 150 200 AMBIENT TEMPERATURE Ta(°C) 3 2007-11-01 JDP2S05FS RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 4 2007-11-01