CAT5110, CAT5118, CAT5119 CAT5123, CAT5124, CAT5125 32-Tap MiniPot™ Digitally Programmable Potentiometers with 2-Wire Interface Features DEscription ■ 0.3µA Ultra-low standby current ■ Single-supply operation: 2.7V to 5.5V ■ Glitchless switching between resistor taps ■ Power-on reset to midscale ■ 2-Wire up/down serial interface ■ Resistance values: 10kΩ, 50kΩ and 100kΩ ■ All devices available in SOT-23 package ■ CAT5110, CAT5118, CAT5119 also available in SC70 CAT5110/5118/5119/5123/5124/5125 linear-taper digitally programmable potentiometers perform the same function as a mechanical potentiometer or a variable resistor. These devices consist of a fixed resistor and a wiper contact with 32-tap points that are digitally controlled through a 2-wire up/down serial interface. The CAT5110 and CAT5125 are configured as potentiometers. The CAT5118/19/23/24 are configured as variable resistors. Three resistance values are available: 10kΩ, 50kΩ and 100kΩ. All devices are available in space-saving 5-pin and 6-pin SOT-23 packages. The CAT5110/5118/5119 are also available in the SC70 package. Applications ■ LCD screen adjustment ■ Volume control ■ Mechanical potentiometer replacement ■ Gain adjustment ■ Line impedance matching Functional Diagram H VDD GND UP-DOWN COUNTER 32-POSITION DECODER CS For Ordering Information details, see page 11. U/D Pin Configuration L sOT-23 sOT-23 VDD H VDD 5 W GND 2 6 GND 2 U/D 3 CAT5110 CAT5125 4 CS U/D 3 sC70 VDD CAT5110 © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice sOT-23 5 H VDD H VDD 5 W GND 2 4 CS U/D 3 6 GND 2 CAT5118 CAT5123 4 CS U/D 3 sC70 6 GND 2 U/D 3 W 5 L CAT5119 CAT5124 H VDD GND 2 4 CS 6 H sC70 5 CAT5118 H 4 CS U/D 3 5 L CAT5119 4 CS Doc. No. 2120, Rev. E CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Pin Descriptions Pin Number CAT5110/ CAT5125 CAT5118/ CAT5123 CAT5119/ CAT5124 1 1 1 VDD Power Supply 2 2 2 GND Ground 3 3 3 U/D Up/Down Control Input. With CS low, a low-to-high transition increments or decrements the wiper position. 4 4 4 CS Chip Select Input. A high-to-low CS transition determines the mode: increment if U/D is high, or decrement if U/D is low. - - 5 L Low Terminal of Resistor 5 - - W Wiper Terminal of Resistor 6 6 6 H High Terminal of Resistor Pin Name Description Absolute Maximum Ratings(1) VDD to GND -0.3V to +6V All Other Pins to GND -0.3V to (VDD + 0.3)V Input and Output Latch-Up Immunity ±200mA Maximum Continuous Current into H, L and W 100kΩ 50kΩ 10kΩ ±0.6mA ±1.3mA ±1.3mA Continuous Power Dissipation (TA = +70ºC) 5-pin SC70* 6-pin SC70* 247mW 245mW Operating Temperature Range -40°C to +85ºC Junction Temperature +150ºC Storage Temperature Range -65ºC to +150ºC Soldering Temperature (soldering, 10s) +300ºC Notes: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. (*) Derate 3.1mW/ºC above TA = +70ºC Doc. No. 2120, Rev. E © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Electrical CHARACTERISTICS VDD = 2.7V to 5.5V, VH = VDD, VL = 0, TA = -40ºC to 85ºC. Typical values are at VDD = 2.7V, TA = 25ºC, unless otherwise noted. Parameter Symbol Conditions Min Typ Max Units DC Performance Resolution 32 End-to-End Resistance (-00) 80 100 120 End-to-End Resistance (-50) 40 50 60 End-to-End Resistance (-10) 8 10 12 End-to-End Resistance Tempco TCR Ratiometric Resistance Tempco Integral Nonlinearity INL Differential Nonlinearity DNL Taps 200 ppm/ºC 5 ppm/ºC ±0.5 Full-Scale Error kΩ ±1 LSB ±1 LSB ±0.1 Zero-Scale Error LSB 1 Wiper Resistance RW CAT5110/18/19 200 600 CAT5123/24/25 80 200 LSB Ω Digital Inputs Input High Voltage VIH Input Low Voltage VIL 0.7 x VDD V 0.3 x VDD V Timing Characteristics (Figures 1, 2) U/D Mode to CS Setup tCU 25 ns CS to U/D Step Setup tCI 50 ns CS to U/D Step Hold tIC 25 ns U/D Step Low Period tIL 25 ns tIH 25 ns U/D Step High Period Up/Down Toggle Rate (1) fTOGGLE Output Settling Time (2) tSETTLE 1 100kΩ variable resistor configuration, CL = 10pF 1 100kΩ potentiometer configuration, CL = 10pF 0.25 MHz μs Power Supply Supply Voltage VDD Active Supply Current (3) IDD Standby Supply Current (4) ISB Notes: (1) Up/Down Toggle Rate: fTOGGLE = 2.7 VDD = +5V 0.3 5.5 V 25 µA 1 µA t SETTLE (2) Typical settling times are dependent on end-to-end resistance. (3) Supply current measured while changing wiper tap, fTOGGLE = 1MHz. (4) Supply current measured while wiper position is fixed. © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice Doc No. 2120, Rev. E CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Typical Operating Characteristics TA = 25ºC, unless otherwise noted. WIPER POSITION 160 140 120 CAT5110/5118/5119 RW (Ω) 100 50K 80 60 CAT5123/5124/5125 40 20 0 VDD = 2.7V 0 5 10 15 20 25 WIPER POSTION 30 VDD= 5.5V VDD= 2.7V Doc. No. 2120, Rev. E © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Functional Description The CAT5110/5118/5119/5123/5124/5125 consist of a fixed resistor and a wiper contact with 32-tap points that are digitally controlled through a 2-wire up/down serial interface. Three end-to-end resistance values are available: 10kΩ, 50kΩ and 100kΩ. The CS and U/D inputs control the position of the wiper along the resistor array. When CS transitions from high to low, the part will go into increment mode if U/D input is high, and into decrement mode when U/D input is low. Once the mode is set, the device will remain in that mode until CS goes high again. A low-to-high transition at the U/D pin will increment or decrement the wiper position depending on the current mode (Figures 1 and 2). The CAT5110/5125 is designed to operate as a potentiometer. In this configuration, the low terminal of the resistor array is connected to ground (pin 2). When the CS input transitions to high (serial interface inactive), the value of the counter is stored and the wiper position is maintained. The CAT5118/5123 performs as a variable resistor. In this device, the wiper terminal and high terminal of the resistor array are connected at pin 5. The CAT5119/5124 is a similar variable resistor, except the low terminal is connected to pin 5. Note that when the wiper reaches the maximum (or minimum) tap position, the wiper will not wrap around to the minimum (or maximum) position. Digital Interface Operation Power-On Reset The MiniPots have two modes of operation when the serial interface is active: increment and decrement mode. The serial interface is only active when CS is low. All parts in this family feature power-on reset (POR) circuitry that sets the wiper position to midscale at powerup. By default, the chip is in the increment mode. Figure 1. Serial Interface Timing Diagram, Increment Mode CS t CU t IC t IL U/D t IH t CI t SETTLE t SETTLE W Note: "W" is not a digital signal. It represents wiper transitions. Figure 2. Serial Interface Timing Diagram, Decrement Mode CS t CU t IC t IH U/D t IL W t CI t SETTLE t SETTLE Note: "W" is not a digital signal. It represents wiper transitions. © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice Doc No. 2120, Rev. E CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Applications Information Adjustable Gain The MiniPots are intended for circuits requiring digitally controlled adjustable resistance, such as LCD contrast control, where voltage biasing adjusts the display contrast. Figure 5 shows how to use either a variable resistor or a potentiometer to digitally adjust the gain of a noninverting op amp configuration, by connecting the Minipot in series with a resistor to ground. The MiniPots have a low 5ppm/ºC ratiometric tempco that allows for a very stable adjustable gain configuration over temperature. Alternative Positive LCD Bias Control An op amp can be used to provide buffering and gain on the output of the CAT5110/CAT5125. This can be done by connecting the wiper output to the positive input of a noninverting op amp as shown in Figure 3. Figure 4 shows a similar circuit for the CAT5119/CAT5124. Figure 3. Positive LCD Bias Control Figure 4. Positive LCD Bias Control +5V +5V H H 30V 30V W VOUT VOUT CAT5119/CAT5124 L CAT5110/CAT5125 L Figure 5a. Adjustable Gain Circuit Figure 5b. Adjustable Gain Circuit V CC VCC VIN VIN VOUT VOUT H L H CAT5110/CAT5125 CAT5118/CAT5123 L Doc. No. 2120, Rev. E W © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Package Information SC-70 6 LEAD e e E1 b D A2 A GAUGE PLANE c L A1 θ L2 L1 SYMBOL MIN NOM MAX A 0.80 A1 0.00 1.10 A2 0.70 b 0.15 c 0.08 0.20 0.22 D 1.80 2.00 2.20 0.10 0.90 1.00 0.30 E 1.15 1.25 1.38 E1 1.80 2.10 2.40 e — 0.65 BSC — L 0.26 0.36 0.46 L1 L2 θ For current Tape and Reel information, download the PDF file from: www.catsemi.com/documents/tapeandreel.pdf 0.425 REF 0.15 BSC 0° 8° Notes: (1) All dimensions are in millimeters. (2) All specifications comply to JEDEC standard M0-203. © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice Doc No. 2120, Rev. E CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 SOT-23 6 LEAD D e E1 E A2 A θ1 θ Gauge Plane b θ2 L1 A1 SYMBOL MIN NOM A L2 L MAX 1.45 A1 0.00 A2 0.90 c 0.08 b 0.30 0.15 1.15 0.50 0.95 BSC D 2.90 BSC E 2.80 BSC E1 1.30 0.22 e L C 1.60 BSC 0.30 0.45 0.60 L1 0.60 REF L2 θ 0.25 BSC 0° 8° θ1 0° 10° θ2 0° 10° For current Tape and Reel information, download the PDF file from: www.catsemi.com/documents/tapeandreel.pdf Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) All specifications comply to JEDEC standard MO-178. Doc. No. 2120, Rev. E © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 SC-70 5 LEAD e e E1 b D A2 A GAUGE PLANE c L A1 θ L2 L1 SYMBOL MIN NOM MAX A 0.80 1.10 A1 0.00 0.10 A2 0.80 1.00 b 0.15 0.30 c 0.10 D 1.80 2.00 2.20 E 1.15 1.25 1.35 E1 1.80 2.10 2.40 e L 0.18 0.65 BSC 0.26 0.36 L1 0.42 REF L2 0.15 BSC θ 0° 0.46 8° For current Tape and Reel information, download the PDF file from: www.catsemi.com/documents/tapeandreel.pdf Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) All specifications comply to JEDEC standard M0-203. © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice Doc No. 2120, Rev. E CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 SOT-23 5 LEAD D e E1 E A2 A θ1 θ Gauge Plane b θ2 L1 A1 SYMBOL MIN NOM A L2 L MAX 1.45 A1 0.00 A2 0.90 c 0.08 b 0.30 0.15 1.15 0.50 0.95 BSC D 2.90 BSC E 2.80 BSC E1 1.30 0.22 e L C 1.60 BSC 0.30 0.45 0.60 L1 0.60 REF L2 θ 0.25 BSC 0° 8° θ1 0° 10° θ2 0° 10° For current Tape and Reel information, download the PDF file from: www.catsemi.com/documents/tapeandreel.pdf Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) All specifications comply to JEDEC standard MO-178. Doc. No. 2120, Rev. E 10 © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Example of Ordering Information Prefix Device # Suffix CAT 5110 SD Optional Company ID Product Number 5110 5118 5119 5123 5124 5125 Package SD: SC70 TB: SOT23 I -10 -G Resistance -10: 10kohms -50: 50kohms -00: 100kohms Temperature Range I: Inductrial (-40ºC to +85ºC) T3 Tape & Reel T: Tape & Reel 3: 3000 units/reel 10: 10000 units/reel Lead Finish G: NiPdAu Blank: Matte-Tin Notes: (1) All packages are RoHS-compliant (Lead-free, Halogen-free). (2) The device used in the example above is a CAT5110SDI-10 -GT3 (NiPdAu, Tape and Reel). (3) The standard finish for SOT23 package is Matte-Tin. (4) The standard finish for SC70 package is NiPdAu. (5) For additional package and temperature options, please contact your nearest Catalyst Semiconductor Sales office. © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 11 Doc No. 2120, Rev. E CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Ordering Information Device Ordering part number Resistor [kΩ] Top Marking Pin package Parts per reel CAT5110 CAT5110SDI-10-GT3 10 JU_ SC70-6 3,000 CAT5110SDI-10-GT10 10 JU_ SC70-6 10,000 CAT5110TBI-10-T3 10 JUYM SOT23-6 3,000 CAT5110TBI-10-T10 10 JUYM SOT23-6 10,000 CAT5110TBI-10-GT3 10 JUYM SOT23-6 3,000 CAT5110TBI-10-GT10 10 JUYM SOT23-6 10,000 CAT5110SDI-50-GT3 50 JV_ SC70-6 3,000 CAT5110SDI-50-GT10 50 JV_ SC70-6 10,000 CAT5110TBI-50-T3 50 JVYM SOT23-6 3,000 CAT5118 Doc. No. 2120, Rev. E CAT5110TBI-50-T10 50 JVYM SOT23-6 10,000 CAT5110TBI-50-GT3 50 JVYM SOT23-6 3,000 CAT5110TBI-50-GT10 50 JVYM SOT23-6 10,000 CAT5110SDI-00-GT3 100 JW_ SC70-6 3,000 CAT5110SDI-00-GT10 100 JW_ SC70-6 10,000 CAT5110TBI-00-T3 100 JWYM SOT23-6 3,000 CAT5110TBI-00-T10 100 JWYM SOT23-6 10,000 CAT5110TBI-00-GT3 100 JWYM SOT23-6 3,000 CAT5110TBI-00-GT10 100 JWYM SOT23-6 10,000 CAT5118SDI-10-GT3 10 JL_ SC70-5 3,000 CAT5118SDI-10-GT10 10 JL_ SC70-5 10,000 CAT5118TBI-10-T3 10 JLYM SOT23-5 3,000 CAT5118TBI-10-T10 10 JLYM SOT23-5 10,000 CAT5118TBI-10-GT3 10 JLYM SOT23-5 3,000 CAT5118TBI-10-GT10 10 JLYM SOT23-5 10,000 CAT5118SDI-50-GT3 50 JM_ SC70-5 3,000 CAT5118SDI-50-GT10 50 JM_ SC70-5 10,000 CAT5118TBI-50-T3 50 JMYM SOT23-5 3,000 CAT5118TBI-50-T10 50 JMYM SOT23-5 10,000 CAT5118TBI-50-GT3 50 JMYM SOT23-5 3,000 CAT5118TBI-50-GT10 50 JMYM SOT23-5 10,000 CAT5118SDI-00-GT3 100 JN_ SC70-5 3,000 CAT5118SDI-00-GT10 100 JN_ SC70-5 10,000 CAT5118TBI-00-T3 100 JNYM SOT23-5 3,000 CAT5118TBI-00-T10 100 JNYM SOT23-5 10,000 CAT5118TBI-00-GT3 100 JNYM SOT23-5 3,000 CAT5118TBI-00-GT10 100 JNYM SOT23-5 10,000 12 © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Ordering Information (Continued) Device Ordering part number Resistor [kΩ] Top Marking Pin package Parts per reel CAT5119 CAT5119SDI-10-GT3 10 JP_ SC70-6 3,000 CAT5119SDI-10-GT10 10 JP_ SC70-6 10,000 CAT5119TBI-10-T3 10 JPYM SOT23-6 3,000 CAT5119TBI-10-T10 10 JPYM SOT23-6 10,000 CAT5119TBI-10-GT3 10 JPYM SOT23-6 3,000 CAT5119TBI-10-GT10 10 JPYM SOT23-6 10,000 CAT5119SDI-50-GT3 50 JR_ SC70-6 3,000 CAT5119SDI-50-GT10 50 JR_ SC70-6 10,000 CAT5119TBI-50-T3 50 JRYM SOT23-6 3,000 CAT5123 CAT5119TBI-50-T10 50 JRYM SOT23-6 10,000 CAT5119TBI-50-GT3 50 JRYM SOT23-6 3,000 CAT5119TBI-50-GT10 50 JRYM SOT23-6 10,000 CAT5119SDI-00-GT3 100 JT_ SC70-6 3,000 CAT5119SDI-00-GT10 100 JT_ SC70-6 10,000 CAT5119TBI-00-T3 100 JTYM SOT23-6 3,000 CAT5119TBI-00-T10 100 JTYM SOT23-6 10,000 CAT5119TBI-00-GT3 100 JTYM SOT23-6 3,000 CAT5119TBI-00-GT10 100 JTYM SOT23-6 10,000 CAT5123TBI-10-T3 10 JLYM SOT23-5 3,000 CAT5123TBI-10-T10 10 JLYM SOT23-5 10,000 CAT5123TBI-10-GT3 10 JLYM SOT23-5 3,000 CAT5123TBI-10-GT10 10 JLYM SOT23-5 10,000 (1) CAT5123TBI-50-T3 50 JMYM SOT23-5 3,000 CAT5123TBI-50-T10 (1) 50 JMYM SOT23-5 10,000 CAT5123TBI-50-GT3 (1) 50 JMYM SOT23-5 3,000 50 JMYM SOT23-5 10,000 CAT5123TBI-50-GT10 (1) (1) 100 JNYM SOT23-5 3,000 CAT5123TBI-00-T10 (1) 100 JNYM SOT23-5 10,000 CAT5123TBI-00-GT3 (1) 100 JNYM SOT23-5 3,000 100 JNYM SOT23-5 10,000 CAT5123TBI-00-T3 CAT5123TBI-00-GT10 (1) Notes: (1) Contact factory for availability. © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 13 Doc No. 2120, Rev. E CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 Ordering Information (Continued) Device CAT5124 Ordering part number CAT5124TBI-10-T3 (1) Top Marking Pin package Parts per reel 10 JLYM SOT23-5 3,000 CAT5124TBI-10-T10 (1) 10 JLYM SOT23-5 10,000 CAT5124TBI-10-GT3 (1) 10 JLYM SOT23-5 3,000 10 JLYM SOT23-5 10,000 CAT5124TBI-50-T3 50 JMYM SOT23-5 3,000 CAT5124TBI-50-T10 50 JMYM SOT23-5 10,000 CAT5124TBI-50-GT3 50 JMYM SOT23-5 3,000 CAT5124TBI-50-GT10 50 JMYM SOT23-5 10,000 CAT5124TBI-10-GT10 (1) (1) 100 JNYM SOT23-5 3,000 (1) 100 JNYM SOT23-5 10,000 CAT5124TBI-00-GT3 (1) 100 JNYM SOT23-5 3,000 CAT5124TBI-00-GT10 (1) 100 JNYM SOT23-5 10,000 CAT5125TBI-10-T3 10 JUYM SOT23-6 3,000 CAT5125TBI-10-T10 10 JUYM SOT23-6 10,000 CAT5125TBI-10-GT3 10 JUYM SOT23-6 3,000 CAT5125TBI-10-GT10 10 JUYM SOT23-6 10,000 (1) CAT5124TBI-00-T3 CAT5124TBI-00-T10 CAT5125 Resistor [kΩ] CAT5125TBI-50-T3 50 JVYM SOT23-6 3,000 CAT5125TBI-50-T10 (1) 50 JVYM SOT23-6 10,000 CAT5125TBI-50-GT3 (1) 50 JVYM SOT23-6 3,000 50 JVYM SOT23-6 10,000 CAT5125TBI-50-GT10 CAT5125TBI-00-T3 (1) (1) 100 JWYM SOT23-6 3,000 CAT5125TBI-00-T10 (1) 100 JWYM SOT23-6 10,000 CAT5125TBI-00-GT3 (1) 100 JWYM SOT23-6 3,000 100 JWYM SOT23-6 10,000 CAT5125TBI-00-GT10 (1) Notes: (1) Contact factory for availability. Doc. No. 2120, Rev. E 14 © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125 REVISION HISTORY Date Rev. Reason 03/10/2004 A Initial Issue 03/18/2004 B Update Typical Operating Characteristics Update SC70 package outline 07/19/2004 C Added SOT-23 package in all areas Update Description Update Electrical Characteristics Update Typical Operating Characteristics Update Functional Description 12/15/2006 D Added CAT5123, CAT5124, CAT5125 Update Features Update Description Update Pin Configuration Update Pin Description Update Electrical Characteristics Update Typical Operating Characteristics Update Functional Description Update Figures 3, 4, 5 and 6 Update Package Information Update Example of Ordering Information Update Ordering information 01/29/07 E Update Electrical Characteristics © 2007 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 15 Doc No. 2120, Rev. E Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: Beyond Memory™, DPP™, EZDim™, MiniPot™, and Quad-Mode™ Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled “Advance Information” or “Preliminary” and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. Catalyst Semiconductor, Inc. Corporate Headquarters 2975 Stender Way Santa Clara, CA 95054 Phone: 408.542.1000 Fax: 408.542.1200 www.catsemi.com Document No:2120 Revision: E Issue date: 01/29/07