!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 o Part Numbering CERALOCKr (MHz) (Part Number) CS T CE 16M0 q w e r 3 *** -R0 t y u i o V 5 qProduct ID yInitial Frequency Tolerance Product ID Design Code CS Ceramic Resonators wFrequency/Capacitance 5 ±0.5% 3 ±0.3% 2 ±0.2% Code Frequency/Capacitance 1 ±0.1% A MHz with No capacitance built-in H ±0.07% T MHz with Built-in Capacitance uLoad Capacity eStructure/Size Code Design Code Structure/Size 1 5/6pF LS Round Lead Type 2 10pF CC Cap Chip Type 3 15pF CR/CE/CG Small-cap Chip Type 4 22pF CV Monolithic Chip Type 5 30/33/39pF CW Small Monolithic Chip Type 6 47pF rNominal Center Frequency iIndividual Specification Expressed by four-digit alphanumerics. The unit is in hertz (Hz). Decimal point is expressed by capital letter "M". tDesign Code Individual Specification *** Three-digit alphanumerics express "Individual Specification". With standard products, "iIndividual Specification" is omitted. Code Design Gpp Thickness Shear mode oPackaging T/Vpp Thickness Expander mode Code Packaging Xpp Thickness Expander mode (3rd overtone) -B0 Bulk pp indicates initial frequency tolerance and load capacity. -A0 Radial Taping H0=18mm -R0 Plastic Taping ø=180mm -R1 Plastic Taping ø=330mm Radial taping is applied to lead type and plastic taping to chip type. 3 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 Ceramic Resonators (CERALOCKr) 1 MHz Chip Type -Tight Frequency Tolerance for Automotive1.4 max. 0.2±0.2 0.6±0.05 1.1±0.1 4.1 max. 0.4 (ref.) 0.4 (ref.) 0.4 (ref.) (3) (2) 0.4±0.1 (1) 0.4±0.1 0.4±0.1 ∗: EIAJ Monthly Code CSTCR_G15C 4.00-7.99MHz 0.75±0.1 ■ Features 1. The series are high accuracy resonators whose total tolerance is available for less than +-3,000ppm. 2. The series has high reliability and is available for a wide temperature range. 3. Oscillation circuits do not require external load capacitors. 4. The series is available for a wide frequency range. 5. The resonators are extremely small and have a low profile. 6. No adjustment is necessary for oscillation circuits. 1.5±0.1 1.5±0.1 (in mm) ∗ 1.1 max. 1.3±0.15 0.10±0.10 3.2±0.15 0.4±0.1 0.1±0.1 3.0 max. 0.50 (ref.) 0.50 (ref.) 0.50 (ref.) (3) (2) (1) 0.4±0.1 0.4±0.1 0.4±0.1 ∗: EIAJ Monthly CSTCE_G15C 8.00-13.99MHz ■ Applications Code (in mm) 0.4±0.1 1. Cluster panel and Control panel 2. Safety control (Anti-lock Brake System, Electronic Stability Control, Airbag, etc.) 3. Engine ECU, Electronic Power Steering, Immobilizer, etc. 4. Car Air conditioner, Power Window, Remote Keyless Entry system, etc. 5. Intelligent Transportation System (Lane Keeping System, Millimeter wave radar, etc.) 6. Battery control for hybrid cars 1.2±0.1 1.2±0.1 ∗ 1.1 max. 1.3±0.15 0.10±0.10 3.2±0.15 0.4±0.1 0.1±0.1 0.9±0.1 3.0 max. 0.5 (ref.) 0.5 (ref.) 0.5 (ref.) (3) (2) (1) 0.4±0.1 0.4±0.1 0.4±0.1 ∗: EIAJ Monthly CSTCE_V13C 14.00-20.00MHz Code 0.4±0.1 1.2±0.1 1.2±0.1 (in mm) Part Number Oscillating Frequency (MHz) Initial Tolerance Temperature Stability (%) Temperature Range (°C) CSTCR_G15C 4.00 to 7.99 ±0.1% ±0.13 -40 to 125 CSTCE_G15C 8.00 to 13.99 ±0.1% ±0.13 -40 to 125 CSTCE_V13C 14.00 to 20.00 ±0.1% ±0.13 -40 to 125 Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use. 4 2.0±0.1 ∗ 0.70±0.10 Chip type CERALOCK(R) with built-in load capacitors provides high accuracy in an extremely small package. MURATA's frequency adjustment and package technology expertise has enabled the development of the chip CERALOCK(R) with built-in load capacitors. This diverse series owes its development to MURATA's original mass production techniques and high reliability, and has achieved importance in the worldwide automotive market. 0.30±0.20 4.5±0.1 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 ■ Oscillation Frequency Measuring Circuit 1 VDD 5pF To Frequency Counter Rf 1MΩ Rd (1) (3) C1 C2 (2) ■ Standard Land Pattern Dimensions CSTCR_G15C (* This Land Pattern is not common to CSTCR_G.) 0.4 0.4 1.1 1.1 CSTCE_G15C 0.4 0.8 0.4 0.8 0.4 2.6 1.90 ~ 2.10 0.4 1.2 1.5 1.5 1.2 Land Pattern Land Pattern (in mm) (in mm) ■ Oscillation Frequency Temperature Stability CSTCE_V13C (* This Land Pattern is not common to CSTCE_V.) CSTCR_G15C +0.2 0.4 0.8 0.4 Oscillating Frequency Shift (%) 0.8 1.90 ~ 2.10 0.4 1.2 1.2 +0.1 0 -0.1 Land Pattern -0.2 -60 -40 -20 0 CSTCE_G15C +60 +80 +100 +120 +140 +80 +100 +120 +140 +0.2 Oscillating Frequency Shift (%) Oscillating Frequency Shift (%) +40 CSTCE_V13C +0.2 +0.1 0 -0.1 -0.2 -60 +20 Temperature (°C) (in mm) -40 -20 0 +20 +40 +60 Temperature (°C) +80 +100 +120 +140 +0.1 0 -0.1 -0.2 -60 -40 -20 0 +20 +40 +60 Temperature (°C) 5 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 Application Circuits Utilization 1 ■ TMP92CD54IF (Toshiba) ■ MB90F387 (Fujitsu) 16-bit Microcomputer Vcc3=3.3V 16-bit Microcomputer Vcc5=5.0V Vcc=5.0V H2 H 0.1µF H1 IC : TMP92CD54IF 74 72 IC : MB90F387 L 27 H1: 36, 68, 86 H2: 2, 4, 15, 40, 50, 61, 75 L: 1, 3, 13, 38, 51, 63, 73, 88 CERALOCKr V1 V1 C2 C1 H: 1, 2, 21, 22, 24 L: 20, 23, 25, 48 C2 CERALOCKr: CSTCE8M00G15Cpp-R0 C1=33pF (Typ.) C2=33pF (Typ.) ■ ST72F561 (HS) (ST Microelectronics) 8-bit Microcomputer Vdd=5.0V L V2 CERALOCKr: CSTCE10M0G15Cpp-R0 C1=33pF (Typ.) C2=33pF (Typ.) ■ MC68HC908AZ60AVFU (Freescale) 26 0.1µF V2 C1 28 CERALOCKr 8-bit Microcomputer Vdd=5.0V H 60 EVALUATION BOARD IC : MC68HC908AZ60AVFU 59 58 IC : ST72F561 (HS) GND 1 1MΩ CERALOCKr L CERALOCKr V1 V2 C1 2 H: 9, 25, 41, 57, 58 L: 8, 24, 40, 55, 56 V1 V2 C1 CERALOCKr: CSTCE16M0V13Cpp-R0 C1=15pF (Typ.) C2=15pF (Typ.) C2 ■ µPD70F3283YGC (Renesas) C2 CERALOCKr: CSTCE8M00G15App-R0 C1=33pF (Typ.) C2=33pF (Typ.) ■ M30842MCT-XXXGP (Renesas) 32-bit Microcomputer Vdd=3.3V 16-bit Microcomputer Vcc=5.0V 10kΩ H 14 H 19 IC : µPD70F3283YGC 12 13 10 4.7µF IC : M30842MCT-XXXGP (High*) L 22 V1 V2 C1 6 C2 20 L CERALOCKr CERALOCKr H: 1, 5, 9, 34, 70 L: 2, 8, 11, 15, 33, 69 CERALOCKr: CSTCE10M0G15Cpp-R0 C1=33pF (Typ.) C2=33pF (Typ.) H: 23, 24, 37, 39, 59, 74, 91, 118, 122, 132, 142, 143 L: 15, 16, 21, 36, 41, 57, 76, 93, 110~113, 120, 121, 130, 140 *High: XIN-XOUT Drive Capacity Select Bit V1 V2 C1 C2 CERALOCKr: CSTCE8M00G15Cpp-R0 C1=33pF (Typ.) C2=33pF (Typ.) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 Ceramic Resonators (CERALOCKr) MHz Chip Type -Standard Frequency Tolerance for Automotive2 2.1 max. 3.0±0.2 ∗ 0.5±0.05 0.3±0.3 6.6 max. 0.45 (Ref.) 0.45 (Ref.) 0.45 (Ref.) t Chip type CERALOCK(R) with built-in load capacitors provides high accuracy in an extremely small package. MURATA's frequency adjustment and package technology expertise has enabled the development of the chip CERALOCK(R) with built-in load capacitors. This diverse series owes its development to MURATA's original mass production techniques and high reliability, and has achieved importance in the worldwide automotive market. 0.45±0.3 7.2±0.2 (3) (2) (1) 1.2±0.2 1.4±0.2 1.2±0.2 t : 1.75±0.05 (2.00—2.99MHz) t : 1.55±0.05 (3.00MHz—) CSTCC_G_A 2.00-3.99MHz ∗ : EIAJ code 1.1±0.1 2.5±0.1 ■ Features 1. The series has high reliability and is available for a wide temperature range. 2. Oscillation circuits do not require external load capacitors. 3. The series is available in a wide frequency range. 4. The resonators are extremely small and have a low profile. 5. No adjustment is necessary for oscillation circuits. (in mm) 2.5±0.1 ∗ (3) 0.2±0.2 (2) 0.4±0.05 (1) 0.4 (ref.) 0.8±0.1 0.4 (ref.) 0.8±0.1 ∗ : EIAJ Monthly Code 1.15±0.05 4.1 max. 0.4 (ref.) 1.4 max. 2.0±0.1 0.3±0.2 4.5±0.1 0.8±0.1 ■ Applications CSTCR_G_B 4.00-7.99MHz 0.4±0.1 0.4±0.1 0.75±0.1 1.5±0.1 1.5±0.1 0.4±0.1 (in mm) ∗ 1.1 max. 1.3±0.15 3.2±0.15 0.10±0.10 0.4±0.1 0.1±0.1 3.0 max. 0.70±0.10 1. Cluster panel and Control panel 2. Safety control (Anti-lock Brake System, Electronic Stability Control, Airbag, etc.) 3. Engine ECU, Electronic Power Steering, Immobilizer, etc. 4. Car Air conditioner, Power Window, Remote Keyless Entry system, etc. 5. Electronic Toll Collection system, Car Navigation, etc. 0.50 (ref.) 0.50 (ref.) 0.50 (ref.) (3) (2) (1) 0.4±0.1 0.4±0.1 0.4±0.1 CSTCE_G_A 8.00-13.99MHz (in mm) 0.4±0.1 M (0.5) (3) 3.0 max. (0.5) (2) (0.5) (1) Terminals (1) and (3) are interchangeable. Terminal (2) should be soldered only to fix the resonator onto PCB Terminal (2) should be electrically 0.4±0.2 0.5±0.2 0.4±0.2 floating so it cannot be connected 0.5±0.3 0.5±0.3 0.5±0.3 anywhere. 0.9±0.1 0.5 (ref.) ∗ 0.4±0.1 0.1±0.1 0.5 (ref.) 1.3±0.1 3.1±0.2 ∗ 1.1 max. 3.7±0.2 1.3±0.15 0.10±0.10 3.2±0.15 1.2±0.1 1.2±0.1 0.5 (ref.) (3) (2) (1) 0.4±0.1 0.4±0.1 0.4±0.1 ∗: EIAJ Monthly CSTCE_V_C 14.00-20.00MHz Code 0.4±0.1 1.2±0.1 1.2±0.1 (in mm) Thickness varies with frequency. *: EIAJ Monthly Code CSACV_X_Q 20.01-70.00MHz 1.6±0.2 1.6±0.2 1.85±0.3 (in mm) Continued on the following page. 7 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Continued from the preceding page. ∗ M (0.7) (3) 1.3±0.1 3.1±0.2 3.7±0.2 (0.9) (2) (0.7) (1) 0.4±0.2 0.5±0.2 0.4±0.2 0.5±0.3 0.5±0.3 0.5±0.3 2 Thickness varies with frequency and built-in capacitance. *: EIAJ code CSTCV_X_Q 20.01-70.00MHz 1.6±0.2 1.6±0.2 1.85±0.3 (in mm) Oscillating Frequency (MHz) Initial Tolerance Temperature Stability (%) Temperature Range (°C) CSTCC_G_A 2.00 to 3.99 ±0.5% ±0.4 [-0.6% to +0.3%:Built-in Capacitance 47pF type within Freq.2.00 to 3.49MHz] -40 to 125 CSTCR_G_B 4.00 to 7.99 ±0.5% ±0.15 -40 to 125 CSTCE_G_A 8.00 to 13.99 ±0.5% ±0.2 -40 to 125 CSTCE_V_C 14.00 to 20.00 ±0.5% ±0.15 -40 to 125 CSACV_X_Q 20.01 to 70.00 ±0.5% ±0.3 -40 to 125 CSTCV_X_Q 20.01 to 70.00 ±0.5% ±0.3 -40 to 125 Part Number Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use. ■ Oscillation Frequency Measuring Circuit CSTCC_G_A CSTCE_G_A/CSTCE_V_C/CSTCR_G_B/CSTCV_X_Q VDD VDD 5pF To Frequency Counter Rf To Frequency Counter Rf 1MΩ Rd Rd (1) (3) C1 (1) C1 C2 (2) VDD 0.01µF To Frequency Counter Rf CL1 8 C2 (2) CSACV_X_Q 22µF + (3) CL2 Jul.15,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 ■ Standard Land Pattern Dimensions CSTCC_G_A CSTCR_G_B 0.8 1.4 1.2 0.8 0.7 0.8 1.2 1.6 1.2 2 3.8~4.4 2.6 1.2 0.7 0.4 0.4 1.5 2.5 0.4 1.5 2.5 Land Pattern Land Pattern (in mm) (in mm) CSTCE_G_A 0.4 0.8 0.4 0.4 0.8 0.4 0.8 0.4 1.90 ~ 2.10 0.8 1.90 ~ 2.10 0.4 CSTCE_V_C (* This Land Pattern is not common to CSTCE_V.) 1.2 1.2 1.2 Land Pattern 1.2 Land Pattern (in mm) (in mm) CSTCV_X_Q 0.5 1.1 0.5 0.5 1.1 0.5 1.1 0.5 1.0 0.5 1.0 0.5 3.1±0.2 3.1±0.2 1.0 0.5 1.1 1.0 0.5 0.5 CSACV_X_Q 1.6 1.6 1.6 Land Pattern (in mm) 1.6 Land Pattern (in mm) 9 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 ■ Oscillation Frequency Temperature Stability CSTCC_G_A CSTCR_G_B +0.2 Oscillating Frequency Shift (%) +0.1 0 -0.1 -0.2 -60 -40 -20 0 +20 +40 +60 +80 +100 +120 +0.1 0 -0.1 -0.2 -60 +140 -40 -20 0 Temperature (°C) Oscillating Frequency Shift (%) Oscillating Frequency Shift (%) +80 +100 +120 +140 0 -0.1 -40 -20 0 +20 +40 +60 +80 +100 +120 +80 +100 +120 +140 +80 +100 +120 +140 +0.1 0 -0.1 -0.2 -60 +140 -40 -20 0 Temperature (°C) +20 +40 +60 Temperature (°C) CSTCV_X_Q CSACV_X_Q +0.2 Oscillating Frequency Shift (%) +0.2 +0.1 0 -0.1 -40 -20 0 +20 +40 +60 Temperature (°C) 10 +60 +0.2 +0.1 -0.2 -60 +40 CSTCE_V_C +0.2 -0.2 -60 +20 Temperature (°C) CSTCE_G_A Oscillating Frequency Shift (%) 2 Oscillating Frequency Shift (%) +0.2 +80 +100 +120 +140 +0.1 0 -0.1 -0.2 -60 -40 -20 0 +20 +40 +60 Temperature (°C) P16E.pdf !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Jul.15,2011 Application Circuits Utilization ■ µPD78F9222MC-5A4 (Renesas) ■ M30260F8AGP (Renesas) 8-bit Microcomputer Vdd=5.0V V'dd=7.0V 16-bit Microcomputer Vcc=5.0V 2 10kΩ H 6 H 7 IC : µPD78F9222MC-5A4 2 3 8 IC : M30260F8AGP (High*) L 23 CERALOCKr V1 H: 5, 20 L: 1 V2 C1 24 L H: 11, 46, 47, 48 L: 4, 9, 44 CERALOCKr C2 *High: XIN-XOUT Drive Capacity Select Bit V1 V2 C1 CERALOCKr: CSTCR6M00G55B-R0 C1=39pF (Typ.) C2=39pF (Typ.) ■ MB90F347D (Fujitsu) C2 CERALOCKr: CSTCE10M0G55A-R0 C1=33pF (Typ.) C2=33pF (Typ.) ■ MC68HC908AZ60AVFU (Freescale) 16-bit Microcomputer Vcc=5.0V 8-bit Microcomputer Vdd=5.0V H EVALUATION BOARD IC : MC68HC908AZ60AVFU IC : MB90F347D 93 92 L 59 CERALOCKr H: 15, 32, 65, 90 L: 16, 35, 44, 66, 91 V1 V2 C1 58 V1 C2 V2 CERALOCKr: CSTCE8M00G55A-R0 C1=33pF (Typ.) C2=33pF (Typ.) ■ ST72F324J6T3 (MS) (ST Microelectronics) C1 8-bit Microcomputer 8-bit Microcomputer Vdd=5.0V H H IC : PIC12F675-I/P(HS) IC : ST72F324J6T3 (MS) 41 2 L H: 13, 21, 32, 43 L: 14, 22, 33, 39, 40 V2 C1 C2 3 V1 CERALOCKr: CSTCR4M00G55B-R0 C1=39pF (Typ.) C2=39pF (Typ.) L 1MΩ CERALOCKr CERALOCKr V1 CERALOCKr: CSTCE16M0V53C-R0 C1=15pF (Typ.) C2=15pF (Typ.) C2 ■ PIC12F675-I/P (HS) (Microchip) Vdd=5.0V 42 GND 1MΩ CERALOCKr H: 1 L: 4, 8 V2 C1 C2 CERALOCKr: CSTCE8M00G52A-R0 C1=10pF (Typ.) C2=10pF (Typ.) 11 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Notice for Automotive ■ Soldering and Mounting (CSTCC/CSTCR/CSTCE_V/CSTCE_G Series) Flux Please use rosin based flux, but do not use water soluble flux. Solder Please use solder (Sn-3.0Ag-0.5Cu) under the following condition. Standard thickness of soldering paste: 0.10 to 0.15mm Recommendable Soldering Profile Pre-heating 60 to 120s 220°C min. 30 to 60s upper limit: 260°C 1s max. lower limit: 245°C 5s max. Heating Peak Temperature 150 to 180°C Temperature shall be measured on the surface of component. (2) Soldering with Iron Be compelled to mount component by using soldering iron, please do not directly touch the component with soldering iron. The terminals of component or electrical characteristics may be damaged if excess thermal stress is applied. Recommendable Soldering with Iron Heating of the soldering iron Watt Shape of the soldering iron Soldering Time Solder Temperature (°C) 2 1. Soldering (1) Re-flow soldering Please mount component on a circuit board by re-flow soldering. Flow soldering is not acceptable. Recommendable Flux and Solder Peak 260 245 220 Heating (220°C min.) 180 150 Pre-heating (150 to 180°C) 60 to 120s Gradual Cooling 30 to 60s 350°C max. 30W max. ø3mm max. 5s max. at one terminal Sn-3.0Ag-0.5Cu (3) Solder Volume Please make the solder volume less than the height of the substrate. When exceeding the substrate, the damage of adhesive for sealing between the metal cap and the substrate may occur. (4) etc. Do not reuse removed component from a circuit board after soldering. (5) Condition for Placement Machines The component is recommended with placement machines with employ optical placement capabilities. The component might be resulted in damage by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines which utilize mechanical positioning. Please contact Murata for details beforehand. 2. Wash (1) Cleaning Solvents HCFC, Isopropanol, Tap water, Demineralized water, Cleanthrough750H, Pine alpha 100S, Techno care FRW Continued on the following page. 12 P16E.pdf Jul.15,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 Notice for Automotive Continued from the preceding page. (2) Temperature Difference : dT *1 dTV60°C (dT=Component-solvent) *1 ex. In case the component at +90°C immerses into cleaning solvent at +60°C, then dT=30°C. 2 (3) Conditions (a) Ultrasonic Wash 1 minute max. in above solvent at +60°C max. (Frequency: 28kHz, Output: 20W/l) (b) Immersion Wash 5 minutes max. in above solvent at +60°C max. (c) Shower or Rinse Wash 5 minutes max. in above solvent at +60°C max. (4) Drying 5 minutes max. by air blow at +80°C max. (5) Others (a) Total washing time should be within 10 minutes. (b) The component may be damaged if it is washed with chlorine, petroleum, or alkali cleaning solvent. 3. Coating Conformal coating of the component is acceptable. However, the resin material, curing temperature, and other process conditions should be evaluated to confirm stable electrical characteristics are maintained. 13 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Notice for Automotive ■ Soldering and Mounting (CSTCV/CSACV Series) Flux Please use rosin based flux, but do not use water soluble flux. Solder Please use solder (Sn-3.0Ag-0.5Cu) under the following condition. Standard thickness of soldering paste: 0.10 to 0.15mm Recommendable Soldering Profile Pre-heating 60 to 120s 220°C min. 30 to 60s upper limit: 260°C 1s max. lower limit: 245°C 5s max. Heating Peak Temperature 150 to 180°C Temperature (°C) 2 1. Soldering (1) Re-flow soldering Please mount component on a circuit board by re-flow soldering. Flow soldering is not acceptable. Recommendable Flux and Solder Peak 260 245 220 Heating (220°C min.) 180 150 Pre-heating (150 to 180°C) 60 to 120s Gradual Cooling 30 to 60s Temperature shall be measured on the surface of component. (2) Soldering with Iron Be compelled to mount component by using soldering iron, please do not directly touch the component with soldering iron. The terminals of component or electrical characteristics may be damaged if excess thermal stress is applied. Recommendable Soldering with Iron Heating of the soldering iron Watt Shape of the soldering iron Soldering Time Solder 350°C max. 30W max. ø3mm max. 5s max. at one terminal Sn-3.0Ag-0.5Cu (3) etc. Do not reuse removed component from a circuit board after soldering. (4) Condition for Placement Machines The component is recommended with placement machines with employ optical placement capabilities. The component might be resulted in damage by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines which utilize mechanical positioning. Please contact Murata for details beforehand. 2. Wash (1) Cleaning Solvents HCFC, Isopropanol, Tap water, Demineralized water, Cleanthrough750H, Pine alpha 100S, Techno care FRW (2) Temperature Difference : dT *1 dTV60°C (dT=Component-solvent) *1 ex. In case the component at +90°C immerses into cleaning solvent at +60°C, then dT=30°C. Continued on the following page. 14 P16E.pdf Jul.15,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 Notice for Automotive Continued from the preceding page. (3) Conditions (a) Ultrasonic Wash 1 minute max. in above solvent at +60°C max. (Frequency: 28kHz, Output: 20W/l) (b) Immersion Wash 5 minutes max. in above solvent at +60°C max. (c) Shower or Rinse Wash 5 minutes max. in above solvent at +60°C max. 2 (4) Drying 5 minutes max. by air blow at +80°C max. (5) Others (a) Total washing time should be within 10 minutes. (b) The component may be damaged if it is washed with chlorine, petroleum, or alkali cleaning solvent. 3. Coating Conformal coating of the component is acceptable. However, the resin material, curing temperature, and other process conditions should be evaluated to confirm stable electrical characteristics are maintained. 15 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. Notice for Automotive ■ Storage and Operating Conditions 2 1. Product Storage Condition Please store the products in a room where the temperature/humidity is stable, and avoid such places where there are large temperature changes. Please store the products under the following conditions: Temperature: -10 to + 40 degrees C Humidity: 15 to 85% R.H. 2. Expiration Date on Storage Expiration date (Shelf life) of the products is six months after delivery under the conditions of a sealed and unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the products may be degraded in solderability and/or rusty. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality, and/or be degraded in the solderability due to the storage in a chemical atmosphere. ■ Rating The component may be damaged if excessive mechanical stress is applied. ■ Handling "CERALOCK" may stop oscillating or oscillate irregularly under improper circuit conditions. 16 (2) Please do not put the products directly on the floor without anything under them to avoid damp and/or dusty places. (3) Please do not store the products in places such as: in a damp heated place, in a place where direct sunlight comes in, in a place applying vibrations. (4) Please use the products immediately after the package is opened, because the characteristics may be reduced in quality, and/or be degraded in the solderability due to storage under the poor conditions. (5) Please do not drop the products to avoid cracking of ceramic elements. 4. Others Conformal coating of the component is acceptable. However, the resin material, curing temperature, and other process conditions should be evaluated to confirm that stable electrical characteristics are maintained. Please be sure to consult with our sales representatives or engineers whenever and prior to using the products. P16E.pdf Jul.15,2011 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 Packaging for Automotive ■ Minimum Quantity Part Number Plastic Tape ø180mm Plastic Tape ø330mm Bulk Dimensions CSTCC_G_A 2,000 6,000 500 a CSTCR_G_B 3,000 9,000 500 a CSTCR_G15C 3,000 9,000 500 a CSTCE_G_A 3,000 9,000 500 b CSTCE_G15C 3,000 9,000 500 b CSTCE_V_C 3,000 9,000 500 b CSTCE_V13C 3,000 9,000 500 b CSTCV_X_Q 2,000 6,000 500 a CSACV_X_Q 2,000 6,000 500 a 2 (pcs.) The order quantity should be an integral multiple of the "Minimum Quantity" shown above. c Dimensions of Reel a b Trailer 160-190 Leader 13.0 Empty 160 min. Empty Components 400-560 (ø180 0–1.5 ) (ø180 0–1.5 ) Empty Components Leader Cover Film Trailer 160-190 Cover Film ø13.0±0.2 2.0±0.5 +1.0 0 9.0 17.0±1.0 Empty 160 min. 400-560 ø13.0±0.2 2.0±0.5 +1.0 0 13.0±1.0 (in mm) ■ Dimensions of Taping +0.10 Direction of Feed 0.90±0.10 10° (1.30 max.) (3˚) 0.25±0.05 1.50 -0.05 Cover Film (in mm) 8.0±0.2 +0.2 ø1.0 -0.0 The cover film peel strength force 0.1 to 0.7N The cover film peel speed 300mm/min. (1.85 max.) 0.3±0.05 (3˚) 3.5±0.05 +0.10 4.0±0.1 2.2±0.1 Direction of Feed 3.40 -0.05 (3)(2)(1) (5.2) 12.0±0.2 +0.1 ø1.5 -0 The cover film peel strength force 0.1 to 0.7N The cover film peel speed 300mm/min. Cover Film 10˚ ø1.5 +0.1 -0.0 2.0±0.05 1.25±0.05 4.0±0.1 4.7±0.1 (9.5) (3)(2)(1) 2.0±0.05 4.0±0.1 5.5±0.05 +0.1 ø1.5 -0 1.75±0.1 CSTCE_G15C 1.75±0.1 CSTCR_G15C 4.0±0.1 (in mm) Continued on the following page. 17 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011 Packaging for Automotive Continued from the preceding page. ■ Dimensions of Taping Direction of Feed 1.10±0.05 (3˚) (1.40 max.) 0.25±0.05 (in mm) Direction of Feed 1.10±0.05 0.25±0.05 (1.40 max.) Thickness of CERALOCKr t1 ∗1 t2 ∗2 (in mm) t2 ∗2 (3˚) 10° t1 ∗1 +0.2 ø1.5 –0.0 0.3±0.1 +0.1 3.35 –0.05 12.0±0.2 5.5±0.1 4.1±0.1 (3)(2)(1) 4.0±0.1 Direction of Feed ∗1, ∗2: Dimensions vary with product thickness of CERALOCKr. 1.30–1.20 1.45±0.1 1.8 max. 1.10–1.00 1.2±0.1 1.5 max. 12.0±0.2 1.75±0.1 8.0±0.2 (1.30 max.) 0.90±0.10 0.25±0.05 5.5±0.1 12.0±0.2 1.75±0.1 t2 ∗2 t1 ∗1 (3˚) Direction of Feed ∗1, ∗2: Dimensions vary with product thickness of CERALOCKr. 1.75±0.1 +0.1 ø1.5 –0.0 +0.2 ø1.5 –0.0 10° CSACV_X_Q (9.5) +0.1 3.35 –0.05 Cover Film (3˚) Direction of Feed 2.0±0.1 4.0±0.1 0.3±0.1 +0.10 4.1±0.1 (3)(2)(1) (9.5) 8.0±0.2 The cover film peel strength force 0.1 to 0.7N The cover film peel speed 300mm/min. 4.0±0.1 +0.1 ø1.5 –0.0 2.0±0.1 3.5±0.05 3.45±0.1 (3)(2)(1) (5.2) 4.0±0.1 +0.1 -0.0 1.50–1.40 1.65±0.1 2.0 max. (in mm) Direction of Feed 1.75±0.1 +0.1 ø1.5 -0.0 Cover Film +0.10 10° CSTCV_X_Q 1.50 -0.05 The cover film peel strength force 0.1 to 0.7N The cover film peel speed 300mm/min. Cover Film 10˚ 18 (3˚) Cover Film CSTCE_V_C Thickness of CERALOCKr t1 ∗1 t2 ∗2 +0.10 (in mm) Dimensions of Carrier Tape 4.0±0.1 The cover film peel strength force 0.1 to 0.7N The cover film peel speed 300mm/min. +0.2 ø1.0 -0.0 1.50 -0.05 The cover film peel strength force 0.1 to 0.7N The cover film peel speed 300mm/min. (1.85 max.) 0.3±0.05 (3˚) 1.25±0.05 The cover film peel strength force 0.1 to 0.7N The cover film peel speed 300mm/min. Cover Film 10˚ ø1.0 3.40 -0.05 (3)(2)(1) (5.2) 12.0±0.2 4.0±0.1 3.5±0.05 1.75±0.1 5.5±0.05 4.7±0.1 (3)(2)(1) (9.5) 2.0±0.05 2.2±0.1 4.0±0.1 ø1.5 +0.1 -0.0 4.0±0.1 +0.1 ø1.5 -0 2.0±0.05 (in mm) CSTCE_G_A +0.1 ø1.5 -0 4.0±0.1 5.5±0.05 Direction of Feed ∗1, ∗2: Dimensions vary with frequency range of CERALOCKr. 2.00–2.99MHz 3.00–3.99MHz Frequency Range 1.85±0.05 1.65±0.05 t1 ∗1 2.45 max. 2.25 max. t2 ∗2 CSTCR_G_B 2.0±0.05 (3˚) t2 ∗2 +0.10 1.50 -0.05 The cover film peel strength force 0.1 to 0.7N The cover film peel speed 300mm/min. Cover Film 10˚ 4.0±0.1 7.6±0.1 (3) (2) (1) 4.0±0.1 ø1.5 +0.3 -0.0 The cover film peel strength force 0.1 to 0.7N 3.3±0.1 The cover film peel speed 300mm/min. Cover Film 10˚ +0.1 ø1.0 -0.0 4.0±0.1 ø1.55±0.05 (9.5) 8.0±0.2 3.45±0.1 (3)(2)(1) (5.2) 3.5±0.05 2 2.0±0.05 0.3±0.05 1.75±0.1 +0.1 ø1.5 -0.0 2.0±0.05 1.75±0.1 CSTCC_G_A 4.0±0.1 t1 ∗1 CSTCE_V13C Dimensions of Carrier Tape 4.0±0.1 (in mm) 1.50–1.40 1.65±0.1 2.0 max. 1.30–1.20 1.45±0.1 1.8 max. 1.10–1.00 1.2±0.1 1.5 max. (in mm) !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. P16E.pdf Jul.15,2011