!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Tel: 0755-83264115
Fax:0755-83955172
URL: http://w.ww.qsdaz.com
Ceramic Resonator
(CERALOCKr)
Application Manual
Murata
Manufacturing Co., Ltd.
Cat.No.P17E-14
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Introduction
Ceramic resonators (CERALOCK®) are made of high
stability piezoelectric ceramics that function as a
mechanical resonator.
This device has been developed to function as a
reference signal generator and the frequency is
primarily adjusted by the size and thickness of the
ceramic element.
With the advance of the IC technology, various
equipment may be controlled by a single LSI integrated
circuit, such as the one-chip microprocessor.
CERALOCK® can be used as the timing element in most
microprocessor based equipment.
In the future, more and more applications will use
CERALOCK® because of its high stability nonadjustment performance, miniature size and cost
savings. Typical applications include TVs, VCRs,
automotive electronic devices, telephones, copiers,
cameras, voice synthesizers, communication equipment,
remote controls and toys.
This manual describes CERALOCK® and will assist you
in applying it effectively.
* CERALOCK® is the brand name of these MURATA
products.
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
1 Characteristics and Types of CERALOCK®
YY02
CONTENTS
1. General Characteristics of CERALOCK ....................................02
2. Types of CERALOCK®..................................................................03
®
kHz Band CERALOCK® (CSBLA Series) .......................................03
MHz Band CERALOCK® (CSALS Series) .....................................04
MHz Band CERALOCK® with Built-in Load Capacitance
(CSTLS Series)..............................................................................06
Reflow Solderable kHz Band CERALOCK® (CSBFB Series) ........07
MHz Band Chip CERALOCK®
(CSACW/CSTCC/ CSTCR/CSTCE/CSTCW Series) .....................08
P17E14.pdf 04.8.24
1
Characteristics and
Types of CERALOCK®
2
Principles of CERALOCK®
3
Specifications of
CERALOCK®
4
Applications of
Typical Oscillation Circuits
5
Characteristics of
CERALOCK® Oscillation Circuits
6
Application Circuits to
Various ICs/LSIs
7
Notice
8
Appendix
2 Principles of CERALOCK® YYYYYYYYYYYYYYYYYYYY10
1. Equivalent Circuit Constants ......................................................10
2. Basic Oscillation Circuits ............................................................13
3 Specifications of CERALOCK®
YYYYYYYYYYYYYYY16
1. Electrical Specifications ..............................................................16
Electrical Specifications of kHz Band CSBLA Series ....................16
Electrical Specifications of MHz Band Lead CERALOCK®
(CSTLS/CSALS Series) .................................................................17
Electrical Specifications of MHz Band Chip CERALOCK®
(CSACW Series) (CSTCC/CSTCR/CSTCE/CSTCW Series) ........18
2. Mechanical and Environmental
Specifications of CERALOCK® ...................................................19
4 Applications of Typical Oscillation Circuits Y21
1. Cautions for Designing Oscillation Circuits ..............................21
2. Application to Various Oscillation Circuits ...............................22
Application to C-MOS Inverter .......................................................22
Application to H-CMOS Inverter ....................................................23
Application to Transistors and Comparators..................................24
5 Characteristics of
CERALOCK® Oscillation Circuits
YYYYYYYYYYYY25
1. Stability of Oscillation Frequency ..............................................25
2. Characteristics of the Oscillation Level .....................................26
3. Characteristics of Oscillation Rise Time ...................................27
4. Starting Voltage ...........................................................................28
YYYY29
1. Application to Microcomputers ..................................................29
6 Application Circuits to Various ICs/LSIs
2. Application to Remote Control ICs ............................................32
3. Application to Various Kinds of VCOs
(Voltage Controlled Oscillators) .................................................33
Application to TV Horizontal Oscillation Circuits ............................33
Application to Stereo Demodulation Circuits .................................34
4. Application to Telephone Dialers ...............................................34
5. Application to ICs for Office Equipment ....................................36
6. Other Kinds of Applications to Various ICs ..............................37
7 Notice YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY38
8
Appendix
Equivalent Circuit Constants of
CERALOCK®YYYYYYYYYYYYYYYYYYYYYYYYYY39
Equivalent Circuit
Constants of CERALOCK®
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
1 Characteristics and Types of CERALOCK®
1. General Characteristics of CERALOCK®
1
Ceramic resonators use the mechanical resonance of
piezoelectric ceramics. (Generally, lead zirconium
titanate: PZT.)
The oscillation mode varies with resonant frequency.
The table on the right shows this relationship.
As a resonator device, quartz crystal is well-known. RC
oscillation circuits and LC oscillation circuits are also
used to produce electrical resonance. The following are
the characteristics of CERALOCK®.
q High stability of oscillation frequency
Oscillation frequency stability is between that of
the quartz crystal and LC or RC oscillation circuits.
The temperature coefficient of quartz crystal is
10–6/°C maximum and approximately 10–3 to 10–4/°C
for LC or RC oscillation circuits. Compared with
these, it is 10–5/°C at –20 to +80°C for ceramic
resonators.
w Small configuration and light weight
The ceramic resonator is half the size of popular
quartz crystals.
e Low price, non-adjustment
CERALOCK® is mass produced, resulting in low
cost and high stability.
Unlike RC or LC circuits, ceramic resonators use
mechanical resonance. This means it is not
basically affected by external circuits or by the
fluctuation of the supply voltage.
Highly stable oscillation circuits can therefore be
made without the need of adjustment.
The table briefly describes the characteristics of various
oscillator elements.
!Vibration Mode and Frequency Range
Frequency (Hz)
Vibration Mode
10k
100k
1M
10M 100M
1G
1
Flexural
mode
2
Length
mode
3
Area
expansion
mode
4
Radius
vibration
5
Shear
thickness
mode
6
Thickness
expander
mode
7
Surface
acoustic
wave
[Note] : ,./ show the direction of vibration
!Characteristics of Various Oscillator Elements
Price
Size
Oscillation
Adjust- Frequency Long-term
Initial
ment
Stability
Tolerance
LC
Inexpensive
Big
Required
±2.0%
Fair
CR
Inexpensive
Small
Required
±2.0%
Fair
Name
Quartz
Crystal
Ceramic
Resonator
2
1k
Symbol
Expensive
Inexpensive
Big
Small
Not
±0.001% Excellent
required
Not
required
±0.5%
Excellent
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Characteristics and Types of CERALOCK®
1
2. Types of CERALOCK®
!Part Numbers and Dimensions of kHz Band
CERALOCK® (CSBLA Series) (Standard Products)
Part Number
Frequency (kHz)
7.9
6
3.
375–429
5.0
!Part Numbering
7.0
5
E
C
8
q
w
e
r
t
y
u
-B0
i
430–509
Non-Washable
3.5
455K
o
qProduct ID
wFrequency/No capacitance built-in
eStructure/Size
rNominal Center Frequency
tType
E : Area Expansion mode,
J : Area Expansion mode (Closed Type)
yFrequency Tolerance
2 : ±0.2%, 3 : ±0.3%, 5 : ±0.5%,
B : 1kHz, C : ±2kHz, Z : Others
uLoad Capacitance Value
iIndividual Specification
With standard products, "i individual Specification" is
omitted, and "o Package Specification Code" is carried up.
oPackaging
–B0 : Bulk
5.0
7.0
5
3.
9.0
LA
510–699
3.5
B
5.0
CSBLA
Washable*
(Closed Type)
5.0
2
2.
J
3.5 6.0
CS
E
9.0
3.
CSBLA
(Ex.)
1
Dimensions (in mm)
9.3
The CSBLA series uses are a vibration mode of the
piezoelectric ceramic element. The dimensions of this
element vary with frequency. The ceramic element is
sealed in a plastic case and the size of the case also
varies with the frequency band. Washable products are
available in all the frequencies ; however, three
standard products (375 to 699kHz) are also made in less
expensive non-washable models.
4.3
kHz Band CERALOCK® (CSBLA Series)
700–1250
2.5
∗Please consult Murata regarding ultrasonic cleaning conditions to avoid
possible damage during ultrasonic cleaning.
3
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
1
Characteristics and Types of CERALOCK®
MHz Band CERALOCK® (CSALS Series)
Because CSALS Series uses the thickness vibration
mode of piezoelectric ceramic element, there is little
difference of dimensions over the whole frequency band.
!Part Numbers and Dimensions of MHz Band
CERALOCK® (CSALS Series)
Part Number
Frequency (MHz)
Dimensions (in mm)
5.5
∗
X
16.00–70.00
3.5
CSALS
6.5
3.0
1
!Part Numbering
5.0±0.3
(Ex.)
CS
A
LS
33M8
X
5
1
q
w
e
r
t
y
u
–B0
i
o
qProduct ID
wFrequency/No capacitance built-in
eStructure/Size
LS : Round Lead Type
rNominal Center Frequency
tType
X : Thickness Longitudinal Vibration (3rd overtone)
yFrequency Tolerance
2 : ±0.2%, 3 : ±0.3%, 5 : ±0.5%, Z : Others
uLoad Capacitance Value
iIndividual Specification
With standard products, "i individual Specification" is
omitted, and "o Package Specification Code" is carried up.
oPackaging
–B0 : Bulk,
–A0 : Radial Taping H0=18mm Ammo Pack (Standard)
4
∗ 16.00−32.99MHz : 3.5
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
Characteristics and Types of CERALOCK®
1
!Specifications of Taped Products of MHz Band CERALOCK® (CSALS Series)
P
P2
dh dh
1
dS
H0
W0
L1
W
W1
d
H1
W2
A
D
D0
P1
F
P0
Item
Code
Dimensions
Tolerance
D
5.5
Height of resonator
A
6.5
±0.5
Dimensions of terminal
d
ø0.48
±0.05
Lead length under the hold down tape
L1
5.0 min.
———
Pitch of component
P
12.7
±0.5
Pitch of sprocket hole
P0
12.7
±0.2
Length from sprocket hole center to lead
P1
3.85
±0.5
Length from sprocket hole center to
component center
P2
6.35
±0.5
Lead spacing
F
5.0
±0.3
Slant to the forward or backward
dh
0
±1.0
Width of carrier tape
W
18.0
±0.5
Width of hold down tape
W0
6.0 min.
———
Position of sprocket hole
W1
9.0
Gap of hold down tape and carrier tape
W2
0
±0.5
+0.5
-0
Distance between the center of
sprocket hole and lead stopper
H0
18.0
±0.5
Total height of resonator
H1
24.5
±1.0
Diameter of sprocket hole
D0
ø4.0
±0.2
0.6
±0.2
0
±1.0
Body tilt
• CSTLS series is also available on tape.
t
dS
Remarks
±1.0
Width of diameter
Total tape thickness
t
Direction of Feed
Tolerance for Pitches 10xP0=127±1
1mm max.
Hold down tape doesn't exceed the carrier tape.
(in mm)
5
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
1
Characteristics and Types of CERALOCK®
!Part Numbers and Dimensions of CERALOCK® with
Built-in Load Capacitance (CSTLS Series)
Part Number
Frequency
Dimensions (in mm)
8.0
5.5
G
3.40–10.00MHz
3.5
CSTLS
2.5 2
.5
!Part Numbering
∗
5.5
3.0
CS
T
LS
4M00
G
5
3
q
w
e
r
t
y
u
-A0
i
o
qProduct ID
wFrequency/Built-in Capacitance
eStructure/Size
LS : Round Lead Type
rNominal Center Frequency
tType
G : Thickness Shear vibration,
X : Thickness Longitudinal Vibration (3rd overtone)
yFrequency Tolerance
1 : ±0.1%, 2 : ±0.2%, 3 : ±0.3%, 5 : ±0.5%, D : DTMF,
Z : Others
uBuilt-in Load capacitance
1 : 5pF, 3 :15pF, 4 : 22pF, 5 : 30pF, 6 : 47pF
iIndividual Specification
With standard products, "i individual Specification" is
omitted, and "o Package Specification Code" is carried up.
oPackaging
–B0 : Bulk,
–A0 : Radial Taping H0=18mm Ammo Pack (Standard)
6
CSTLS
X
6.5
(Ex.)
16.00–70.00MHz
3.5
1
As CSTLS series does not require externally mounted
capacitors, the number of components can be reduced,
allowing circuits to be made more compact.
The table shows the frequency range and appearance of
the three terminal CERALOCK® with built-in load
capacitance.
3.0
MHz Band CERALOCK® with Built-in Load
Capacitance (CSTLS Series)
2.5 2.5
∗ 16.00−32.99MHz : 3.5
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
1
Characteristics and Types of CERALOCK®
Reflow Solderable kHz Band CERALOCK®
(CSBFB Series)
!Dimensions of Reflow Solderable CERALOCK®
(CSBFB Series)
Reflow solderable kHz band CERALOCK® (CSBFB
series) have been developed to meet down sizing and
S.M.T. (Surface Mount Technology) requirements.
Part Number *1
Frequency (kHz)
Dimensions (in mm)
FB
500K
J
5
8
q
w
e
r
t
y
u
5.0
–R1
i
o
qProduct ID
wFrequency/No capacitance built-in
eStructure/Size
rNominal Center Frequency
tType
J : Area Expansion mode (Closed type)
yFrequency Tolerance
2 : ±0.2%, 3 : ±0.3%, 5 : ±0.5%,
B : ±1kHz, C : ±2kHz, Z : Others
uLoad Capacitance Value
iIndividual Specification
With standard products, "i individual Specification" is
omitted, and "o Package Specification Code" is carried up.
oPackaging
–B0 : Bulk,
–R1 : Plastic Taping φ330mm Reel Package
0
6.
CSBFB
5.0
700–1250*2
J
2.3
B
2.
0
CS
430–519
J
2.5
2.
0
(Ex.)
3.3
CSBFB
!Part Numbering
1
7.5
5
8.
∗1 Please consult Murata regarding ultrasonic cleaning conditions to avoid
possible damage during Ultrasonic cleaning.
∗2 Not available for certain frequencies
!Dimensions of Carrier Tape for CSBFB Series (430 to 519kHz Type)
16.0±0.3
11.4±0.1
7.5±0.1
ø1.5±0.1
13.3±0.1
2.0±0.1
1.75±0.1
4.0±0.1
10˚
(4.6max.)
t0.3
8.05±0.1 3˚ max.
Cover Film
3.5±0.1
12.0±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
Direction of Feed
(in mm)
• Different Dimensions of carrier tape in 700 to 1250kHz.
7
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
1
Characteristics and Types of CERALOCK®
!Part Numbering
(Ex.)
CS
T
CR
4M00
G
5
3
q
w
e
r
t
y
u
-R0
i
o
qProduct ID
wFrequency/No capacitance built-in
A : No Capacitance Built-in, T : Built-in Capacitance
eStructure/Size
CC/CR/CE : Cap Chip Type, CW : Monolithic Chip Type
rNominal Center Frequency
tType
G : Thickness Shear Vibration,
V : Thickness Longitudinal Vibration,
X : Thickness Longitudinal Vibration (3rd overtone)
yFrequency Tolerance
1 : ±0.1%, 2 : ±0.2%, 3 : ±0.3%, 5 : ±0.5%, Z : Others
uLoad Capacitance Value
(In case of CSACW, value is for external capacitance of
standard circuit)
1 : 5pF or 6pF, 2 : 10pF, 3 : 15pF, 5 : 33pF or 39pF,
6 : 47pF
iIndividual Specification
With standard products, "i individual Specification" is
omitted, and "o Package Specification Code" is carried up.
oPackaging
–B0 : Bulk,
–R0 : Plastic Taping φ180mm Reel Package
8
Frequency (MHz)
Dimensions
Standard Land Pattern (in mm)
2.
0
Part Number
2.5
1.0
∗1
0.5
X
20.01–70.00
0.5
2.0±0.2
CSACW
0.8
0.3
1
The MHz band Chip CERALOCK® has a wide frequency
range and small footprint to meet further down sizing
and high-density mounting requirements.
The table shows the dimensions and two terminals
standard land patterns of the CERALOCK® CSACW
series.
The second table shows the dimensions and three
terminals standard land patterns of CSTCC/CSTCR/
CSTCE/CSTCW series chip resonator (built-in load
capacitance type). And the carrier tape dimensions of
CSTCR series are shown on the next page.
!Dimensions and Standard Land Pattern of Chip
CERALOCK® (CSACW Series)
0.8
0.3
MHz Band Chip CERALOCK® (CSACW/CSTCC/
CSTCR/CSTCE/CSTCW Series)
∗1 Thickness varies with frequency.
2.0
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
1
Characteristics and Types of CERALOCK®
!Dimensions and Standard Land Pattern of Chip
CERALOCK® (CSTCC/CSTCR/CSTCE/CSTCW Series)
!Dimensions of Carrier Tape for Chip CERALOCK®
Dimensions
Standard Land Pattern (in mm)
4.0±0.1
W0.1
ø1.5 Y0
2.0±0.05
0
3.
2.5
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
Cover Film
10˚
2.5
3˚ max.
12.0±0.2
5.5±0.05
4.7±0.1
W0.1
ø1.5Y0
2.2±0.1
(1.85 max.)
4.0±0.1
0.3±0.05
(9.5)
1.2 1.2 1.4 1.2 1.2
2.00–3.99
3.8~4.4
G
(3) (2) (1)
1.6
∗1
CSTCC
1
7.2
1.25±0.05
Frequency (MHz)
1.75±0.1
CSTCR Series
Part Number
1.2
2.
0
4.5
Direction of Feed
(in mm)
0.8 0.7 0.8 0.7 0.8
G*2
4.00–7.99
2.6
1.6
CSTCR
0.4
1.5
3
0.4
3.2
0.8
1.
0.4
1.5
0.4 0.8 0.4 0.8
G*2
0.4
8.00–12.50
1.90 ~ 2.10
CSTCE
1.2
3
3.2
1.0
1.
1.2
0.3 0.65 0.3 0.65 0.3
V*2
12.51–20.00
1.6
CSTCE
0.95
0.95
2.
0
2.5
1.0
∗1
X*2
20.01–70.00
0.8
0.3
2.00±0.2
CSTCW
0.8
0.3
0.5 0.5 0.5 0.5 0.5
1.0
1.0
∗1 Thickness varies with frequency
∗2 Conformal coating or washing of the components is not acceptable
because they are not hermetically sealed.
9
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
2 Principles of CERALOCK®
1. Equivalent Circuit Constants
Symbol
Impedance between Two Terminals Z=R+jx
(R : Real Component, X : Impedance Component)
Phase φ =tan-1X/R
Fig. 2-1 Symbol of the Two Terminal CERALOCK®
Impedance [Z] (Ω)
105
104
103
102
10
Fr
Fa
Frequency (kHz)
90
Fr=1/2π
L1C1
Fa=1/2π L1C1C0/(C1+C0)=Fr 1+C1/C0
Qm=1/2πFrC1R1
(2-1)
(2-2)
(2-3)
(Qm : Mechanical Q)
Considering the limited frequency range of FrVFVFa,
the impedance is given as Z=Re+jωLe (LeU0) as shown
in Fig. 2-4, and CERALOCK® should work as an
inductance Le (H) having the loss Re (Ω).
Phase φ (deg)
2
Fig. 2-1 shows the symbol for a ceramic resonator. The
impedance and phase characteristics measured between
the terminals are shown in Fig. 2-2. This illustrates that
the resonator becomes inductive in the frequency zone
between the frequency Fr (resonant frequency), which
provides the minimum impedance, and the frequency Fa
(anti-resonant frequency), which provides the maximum
impedance.
It becomes capacitive in other frequency zones. This
means that the mechanical vibration of a two terminal
resonator can be replaced equivalently with a
combination of series and parallel resonant circuits
consisting of an inductor : L, a capacitor : C, and a
resistor : R. In the vicinity of the specific frequency
(Refer to Note 1 on page 12.), the equivalent circuit can
be expressed as shown in Fig. 2-3.
Fr and Fa frequencies are determined by the
piezoelectric ceramic material and the physical
parameters. The equivalent circuit constants can be
determined from the following formulas. (Refer to Note
2 on page 12.)
0
-90
Fig. 2-2 Impedance and Phase Characteristics of CERALOCK®
L1
C1
R1
C0
R1 : Equivalent Resistance
L1 : Equivalent Inductance
C1 : Equivalent Capacitance
C0 : Parallel Equivalent Capacitance
Fig. 2-3 Electrical Equivalent Circuit of CERALOCK®
Re
Le
Re : Effective Resistance
Le : Effective Inductance
Fig. 2-4 Equivalent Circuit of CERALOCK®
in the Frequency Band FrVFVFa
10
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
2
Principles of CERALOCK®
CSBLA455KC8–B0
1M
100k
Impedance [Z] (Ω)
The table on this page shows comparison for the
equivalent constants between CERALOCK® and quartz
crystal oscillator.
In comparison, there is a large difference in capacitance
and Qm, which results in the difference of oscillating
conditions, when actually operated.
The table in the appendix shows the standard values of
equivalent circuit constant for each type of
CERALOCK®. Furthermore, other higher harmonic
modes exist, other than the desired oscillation mode.
These other oscillation modes exist because the ceramic
resonator uses mechanical resonance.
Fig. 2-5 shows those characteristics.
Main Vibration
10k
Thickness Vibration
2
1k
100
10
1
0
1
2
3
4
5
6
7
8
9
10
Frequency (MHz)
CSTLS4M00G53–B0
1M
Main Vibration
Impedance [Z] (Ω)
100k
10k
3rd Vibration
1k
100
10
1
0
10
20
30
40
Frequency (MHz)
Fig. 2-5 Spurious Characteristics of CERALOCK®
!Comparison of Equivalent Circuits of CERALOCK® and Crystal Oscillator
Resonator
Oscillation Frequency
L1 (µH)
C1 (pF)
C0 (pF)
R1 (Ω)
Qm
455kHz
7.68×103
16.7
272.8
10.1
2136
13
2.00MHz
3
1.71×10
4.0
20.8
43.9
475
177.2
4.00MHz
0.46×103
3.8
19.8
9.0
1220
350.9
8.00MHz
3
0.13×10
3.5
19.9
8.0
775
641.6
453.5kHz
8.60×106
0.015
5.15
23000
0.6
2.457MHz
7.20×105
0.005
2.39
37.0
298869
4.00MHz
5
2.10×10
0.007
2.39
22.1
240986
6
8.00MHz
1.40×104
0.027
5.57
8.0
88677
19
CERALOCK®
Crystal
1060
dF (kHz)
3
11
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
2
P17E14.pdf 04.8.24
Principles of CERALOCK®
2
Notes
(Note 1)
The relationship between the size of the resonator
and the resonant frequency is described as follows.
For example, the frequency doubles if the thickness
doubles, when thickness vibration is used.
The following relationship is obtained when the
length of the resonators is r, the resonance
frequency is Fr, the speed of sound waves travelling
through piezoelectric ceramics, and the wavelength
is λ.
Fr·r = Const.
(frequency constant, Fr·t for the thickness)
λ = 2r
C = Fr·λ = 2Fr·r
As seen in the above formula, the frequency
constant determines the size of the resonator.
(Note 2)
In Fig. 2-3, when resistance R1 is omitted for
simplification, the impedance Z (ω) between two
terminals is expressed by the following formula.
1 ( jωL1+ 1 )
jωC0
jωC1
Z (ω) =
1 + ( jωL1+ 1 )
jωC0
jωC1
j ( ωL1 –
=
1 + C0 – ω2 C0L1
C1
When ω =
1 = ωr, Z (ωr) =0
L1C1
When ω =
1
= ωa, Z (ωa) = ∞
C0C1L1/(C0+C1)
Therefore from ω =2πF,
Fr = ωr/2π =
r=λ / 2
Fa = ωa/2π =
Amplitude
Range of
Standing
Wave
1 )
ωC1
2π
2π
1
L1C1
1
= Fr
C0C1L1/(C0+C1)
L1
C1
(Min.Amplitude) (Max.Amplitude)
C0
Fig. 1
12
Fig. 2
1+ C1
C0
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Principles of CERALOCK®
2
2. Basic Oscillation Circuits
Generally, basic oscillation circuits can be grouped into
the following 3 categories.
q Use of positive feedback
w Use of negative resistance element
e Use of delay in transfer time or phase
In the case of ceramic resonators, quarts crystal
oscillators, and LC oscillators, positive feedback is the
circuit of choice.
Among the positive feedback oscillation circuit using an
LC, the tuning type anti-coupling oscillation circuit,
Colpitts and Hartley circuits are typically used.
See Fig. 2-6.
In Fig. 2-6, a transistor, which is the most basic
amplifier, is used.
The oscillation frequencies are approximately the same
as the resonance frequency of the circuit consisting of L,
CL1 and CL2 in the Colpitts circuit or consisting of L1
and L2 in the Hartley circuit. These frequencies can be
represented by the following formulas. (Refer to Note 3
on page 15.)
(Colpitts Circuit)
1
fosc. =
2π L · CL1 · CL2
CL1 + CL2
(Hartley Circuit)
1
fosc. =
2π C (L1+L2)
CL1
L2
L1
CL2
2
L
C
Colpitts Circuit
Hartley Circuit
Fig. 2-6 Basic Configuration of LC Oscillation Circuit
Amplifier
Mu Factor : α
Phase Shift : θ 1
Feedback Circuit
Feedback Ratio : β
Phase Shift : θ 2
(2-4)
Oscillation Conditions
Loop Gain G= α · β U1
Phase Shift θ = θ 1+ θ 2=360°×n
Fig. 2-7 Principle of Oscillation
(2-5)
In an LC network, the inductor is replaced by a ceramic
resonator, taking advantage of the fact that the
resonator becomes inductive between resonant and antiresonant frequencies.
This is most commonly used in the Colpitts circuit.
The operating principle of these oscillation circuits can
be seen in Fig. 2-7. Oscillation occurs when the
following conditions are satisfied.
Loop Gain G = α · β U1
Phase Amount
θ = θ 1 + θ 2 = 360°×n (n = 1, 2, ···)
(2-6)
In Colpitts circuit, an inverter of θ 1 = 180° is used, and
it is inverted more than θ 2 = 180° with L and C in the
feedback circuit. The operation with a ceramic resonator
can be considered the same.
13
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
2
P17E14.pdf 04.8.24
Principles of CERALOCK®
It is general and simple to utilize inverter for Colpitts
circuit with CERALOCK®.
Fig. 2-8 shows the basic oscillation circuit with inverter.
In open loop circuit by cutting at A point, it is possible
to measure loop gain G and phase shift θ.
Fig. 2-9 shows the actual measuring circuit, and the
example of measuring result is shown in Fig. 2-10.
α(θ 1)
Rf
A
CERALOCK®
CL1
2
CL2
β (θ 2)
Fig. 2-8 Basic Oscillation Circuit with inverters
α(θ 1)
IC
β (θ 2)
CERALOCK®
Zin1MΩ//8pF
0.01µF
Z0=50Ω
Rf
Vector
Volt
Meter
C2 C1
Vin
S.S.G
Loop Gain : G= α · β
Phase Shift : θ 1+ θ 2
Fig. 2-9 Measuring Circuit Network of Loop Gain and Phase Shift
40
180
30
Phase
(Oscillation)
90
Gain
10
0
0
Phase (deg.)
Loop Gain (dB)
20
-10
-20
CERALOCK®
CSTLS4M00G53–B0
VDD=+5V
CL1=CL2=15pF
IC : TC4069UBP
-90
-30
-40
3.80
3.90
4.00
4.10
4.20
-180
Frequency (MHz)
40
180
90
(No Oscillation)
0
0
Phase (deg.)
Loop Gain (dB)
Phase
Gain
-90
-40
3.80
3.90
4.00
4.10
4.20
-180
CERALOCK®
CSTLS4M00G53–B0
VDD=+2V
CL1=CL2=15pF
IC : TC4069UBP
Frequency (MHz)
Fig. 2-10 Measured Results of Loop Gain and Phase Shift
14
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Principles of CERALOCK®
2
2
Notes
(Note 3)
Fig. 3 shows the equivalent circuit of an emitter
grounding type transistor circuit. In the figure, Ri
stands for input impedance, R0 stands for output
impedance and β stands for current amplification
rate.
When the oscillation circuit in Fig. 2-6 is expressed
by using the equivalent circuit in Fig. 3, it
becomes like Fig. 4. Z1, Z2 and Z are as shown in
the table for each Hartley type and Colpitts type
circuit.
The following 3 formulas are obtained based on
Fig. 4.
-
β R0
R
βR0Z1Z2=(Z1+Ri)Z2 –{Z1(Z2+Z)+
βR0Z1Z2=(Z2+Z+Z1)Ri}(Z2+R0)
2
1
+
···················(4)
Then, as Z1, Z2 and Z are all imaginary numbers,
the following conditional formula is obtained by
dividing the formula (4) into the real number part
and the imaginary number part.
(Imaginary number part)
Z1Z2Z+(Z1+Z2+Z)RiR0=0
(Real number part)
βR0Z1Z2+Z1(Z+Z2)R0+
Z2(Z+Z1)Ri=0
R0
1
As i1 ≠ 0, i2 ≠ 0, i3 ≠ 0 are required for continuous
oscillation, the following conditional formula can be
performed by solving the formulas of (1), (2) and (3)
on the current.
·············(5)
···················(6)
Formula (5) represents the phase condition and
formula (6) represents the power condition.
Oscillation frequency can be obtained by applying
the elements shown in the aforementioned table to
Z1 Z2 and Z solving it for angular frequency ω.
Fig. 3
(Hartley Type)
(L1L2) C{1+
-
1
R
β R0
1
ω2osc = (2π fosc.) 2 =
Z
R0
1
2
3
1
+
Z2
L1 · L2
}
(L1 + L2) CR R0
···················(7)
Z1
(Colpitts Type)
ω2osc = (2π fosc.) 2 =
Hartley Type
Colpitts Type
Z1
jωL1
1 / jωCL1
Z2
jωL2
1 / jωCL2
Z
1 / jωC
jωL
Fig. 4 Hartley/Colpitts Type LC Oscillation Circuits
β R0i1+(R0+Z2) i2–Z2i3=0
Z1i1+Z2i2–(Z2+Z+Z1) i3=0
(Z1+Ri) i1–Z1i3=0
···················(1)
···················(2)
···················(3)
1
L
· {1+
}
(CL1+CL2) R R0
L1·CL2
C
L
CL1+CL2
···················(8)
In either circuit, the term in brackets will be 1 as
long as Ri and R0 is large enough. Therefore
oscillation frequency can be obtained by the
following formula.
(Hartley Type) fosc. =
2π
(Colpitts Type) fosc. =
2π
1
(L1+L2) C
1
C
L · L1·CL2
CL1+CL2
·······(9)
·····(10)
15
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
3 Specifications of CERALOCK®
1. Electrical Specifications
3
The frequency stability of CERALOCK® is between that
of crystal and LC or RC oscillators. Temperature
stability is ±0.3 to ±0.5% against initial values within
-20 to +80°C. The initial frequency precision is
±0.5% for standard products. The frequency of the
standard CERALOCK® is adjusted by the standard
measuring circuit, but the oscillation frequency may
shift when used in the actual IC circuit. Usually, if the
frequency precision needed for clock signal of a 1 chip
microcomputer is approximately ±2 to 3% under
working conditions, CERALOCK® standard type can be
used in most cases. If exact oscillation frequency is
required for a special purpose, Murata can manufacture
the ceramic resonator for the desired frequency.
The following are the general electrical specifications of
CERALOCK®. (As for the standard measuring circuit of
oscillation frequency, please refer to the next chapter
“Application to Typical Oscillation Circuit”.)
!Resonant Impedance Specifications of CSBLA Series
Electrical Specifications of kHz Band CSBLA
Series
Electrical specifications of CSBLA series are shown in
the tables. The value of load capacitance (CL1, CL2) and
damping resistance (Rd) depend on the frequency. (The
initial frequency tolerance of standard CSBLA- J type
is ±0.5% max.)
Frequency Range (kHz)
Resonant Impedance (Ω max.)
0375–0450
120
0451–0504
130
0505–0799
140
0800–0899
160
0900–1099
100
1100–1250
120
!Frequency Specifications of CSBLA Series
Item
Frequency (kHz)
Part Number
Initial Tolerance of Temperature Stability of
Oscillation
Oscillation Frequency
Frequency
(-20 to +80°C)
Oscillating
Frequency Aging
Standard Circuit for
Oscillation Frequency
VDD
CSBLA Series
375–699
±2kHz
16
IC
1MΩ
±0.3%
(with MOS IC/
H–CMOS IC)
IC
700–1250
±0.5%
±0.3%
Rd
CL1
X
CL2
IC : CD4069UBE
IC : (MOS)
IC : TC74HCU04
IC : (H-CMOS)
VDD : +5V
X : CERALOCK®
CL1, CL2, Rd : Depends on frequency
:(cf. Fig. 4-2, 4-3)
Output
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Specifications of CERALOCK®
3
!Resonant Impedance Specifications of
CSTLS/CSALA/CSALS Series
Electrical Specifications of MHz Band Lead
CERALOCK® (CSTLS/CSALS Series)
Electrical specifications of CSTLS/CSALS series are
shown in the tables. Please note that oscillation
frequency measuring circuit constants of the CSTLSG56/CSALS- X55 series (with H-CMOS IC) depends on
frequency.
Type
Frequency Range (MHz) Resonant Impedance (Ω max.)
CSTLS- G
CSALS- X/CSTLS- X
13.40 — 03.99
150
14.00 — 07.99
130
18.00 — 10.00
125
16.00 — 32.99
150
33.00 — 60.00
140
60.01 — 70.00
150
!General Specifications of CSALS Series
Item
Part Number
Frequency
Range
(MHz)
Initial Tolerance
Of Oscillation
Frequency
Temperature Stability
of Oscillation
Frequency
(-20 to +80°C)
Oscillating
Frequency
Aging
3
Standard Circuit for
Oscillation Frequency
VDD
IC
IC
Output
1MΩ
Rd
CSALS- X
X
16.00—70.00
(with H-CMOS IC)
±0.5%
±0.2%
±0.2%
CL1
CL2
IC : TC74HCU04∗
VDD : +5V
X : CERALOCK®
CL1, CL2, Rd : Depends on frequency
: (cf. Fig. 4-3)
∗ 60.01–70.00MHz : SN74AHCU04
MHz band three terminal CERALOCK® (CSTLS Series)
is built-in load capacitance.
Fig. 3-1 shows the electrical equivalent circuit.
The table shows the general specifications of the CSTLS
series. Input and output terminals of the three terminal
CERALOCK® are shown in the table titled Dimensions
of CERALOCK® CSTLS series in Chapter 1 on page 6.
But connecting reverse, the oscillating characteristics
are not affected except that the frequency has slight lag.
CSTLS Series
Fig. 3-1 Symbol of the Three Terminal CERALOCK®
!General Specifications CSTLS Series
Item
Part Number
Frequency
Range
(MHz)
Initial Tolerance Temperature Stability
of Oscillation
Of Oscillation
Frequency
Frequency
(-20 to +80°C)
Oscillating
Frequency
Aging
Standard Circuit for
Oscillation Frequency
VDD
CSTLS- G53/56
03.40—10.00
±0.5%
±0.2%*1
±0.2%
IC
IC
Output
1MΩ
X
Rd
∗2 (1)
CSTLS- X
16.00—70.00
±0.5%
±0.2%
(3)
±0.2%
C1
C2
(2)
IC : TC4069UBP*3
VDD : +5V
X : CERALOCK®
Rd : 680Ω*4
∗1 This value varies for built-in Capacitance
∗2 If connected conversely, there may occur a little frequency lag.
∗3 G56/X series : TC74HCU04, CSTLS series (60.01–70.00MHz) : SN74AHCU04
∗4 This resistance value applies to the CSTLS- G56 series.
17
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
3
Specifications of CERALOCK®
!Resonant Impedance of
CSTCC/CSTCR/CSTCE/CST(A)CW Series
Electrical Specifications of MHz Band Chip
CERALOCK® (CSACW Series)
(CSTCC/CSTCR/CSTCE/CSTCW Series)
Type
General specifications of chip CERALOCK® (CSACW
series) (CSTCC/CSTCR/CSTCE/CSTCW series) are
shown in the tables respectively.
Frequency Range (MHz) Resonant Impedance (Ω max.)
02.00—02.99
80
03.00—03.99
50
04.00—05.99
60
06.00—07.99
50
08.00—10.00
40
10.01—12.50
30
12.51—13.99
50
14.00—20.00
40
20.01—24.99
80
25.00—29.99
60
30.00—60.00
50
60.01—70.00
60
CSTCC-G
CSTCR-G
CSTCE-G
CSTCE-V
3
CSACW-X/CSTCW-X
!General Specifications of CSACW Series
Item
Part Number
Frequency Range
(MHz)
Initial Tolerance
of Oscillation
Frequency
Temperature Stability of
Oscillation Frequency
(-20 to +80°C)
Oscillating
Frequency Aging
Standard Circuit for
Oscillation Frequency
VDD
IC
IC
CSACW- X53
±0.5%
20.01—24.99
±0.1%
±0.2%
Output
1MΩ
X
CL1
CSACW- X51
±0.5%
25.00—70.00
±0.2%
CL2
±0.1%
IC : TC74HCU04*
VDD : +5V
X : Chip CERALOCK®
CL1, CL2 : This value varies for frequency.
Standard Circuit for
Oscillation Frequency
∗ X51 Series (60.01—70.00MHz); SN74AHCU04
!General Specifications of CSTCC/CSTCR/CSTCE/CSTCW Series
Item
Part Number
CSTCC- G
Frequency Range
(MHz)
2.00—03.99
Initial Tolerance
of Oscillation
Frequency
Temperature Stability of
Oscillation Frequency
(-20 to +80°C)
Oscillating
Frequency Aging
±0.5%
±0.3%*3
±0.3%
VDD
IC
IC
Output
CSTCR- G
4.00—07.99
±0.5%
±0.2%
±0.1%
1MΩ
*2
X
CSTCE- G
8.00—12.50
±0.5%
±0.2%
±0.1%
(1)
(3)
C1
CSTCE- V
CSTCW- X
12.51—20.00
20.01—70.00
±0.5%
±0.5%
±0.3%
±0.2%
∗1 V, X Series;TC74HCU04, X Series (60.01—70.00MHz); SN74AHCU04
∗2 If connected with wrong direction, above specification may not be guaranteed.
∗3 This value varies for built-in Capacitance and Frequency.
18
C2
(2)
±0.3%
±0.1%
IC : TC4069UBP*1
VDD : +5V
X : Chip CERALOCK®
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
Specifications of CERALOCK®
3
2. Mechanical and Environmental Specifications of CERALOCK®
The tables show the standard test conditions of mechanical strength and
environmental specifications of CERALOCK®.
Fig. 3-2 shows the changes of oscillation frequency in each test, the table on the
next page shows the criteria after the tests, and Fig. 3-3 shows the reflow
soldering profile.
!Test Conditions for Standard Reliability of CERALOCK®
Item
Conditions
a
1. Shock Resistance
Measure after dropping from a height of
2. Soldering
Heat Resistance
Lead terminals are immersed up to 2.0 mm from the resonator's body in solder bath of c , and then the resonator shall be
measured after being placed in natural condition for 1 hour.*1
Reflow profile show in Fig. 3-5 of heat stress is applied to the resonator, then being placed in natural condition for 1 hour, the
resonator shall be measured.*2
3. Vibration Resistance
Measure after applying vibration of 10 to 55Hz amplitude of 2 mm to each of 3 directions, X, Y, Z.
4. Humidity Resistance
Keep in a chamber with temperature of
5. Storage at
High Temperature
Keep in a chamber at 85±2°C for
6. Storage at
Low Temperature
Keep in a chamber at
7. Temperature Cycling
Keep in a chamber at -55°C for 30 minutes. After leaving at room temperature for 15 minutes, keep in a chamber at +85°C for 30
minutes, and then room temperature for 15 minutes. After 10 cycles of above, measure at room temperature.
8. Terminal Strength
Apply 1 kg of static load vertically to each terminal and measure.
f
e
°C for
d
cm to
floor surface 3 times.
b
and humidity of 90 to 95% for
e
3
hours. Leave for 1 hour before measurement.
hours. Leave for 1 hour before measurement.
e
hours. Leave for 1 hour before measurement.
∗1 Applies to CERALOCK® Lead Type
∗2 Applies to MHz Band Chip CERALOCK®
1. CSBLA Series
Type
fosc.
a
b
c
d
e
f
J
700—1250kHz
100
concrete
350±10°C
60±2°C
1000
−55±2°C
E
375—0699kHz
075
concrete
350±10°C
40±2°C
0500
−25±2°C
2. CSALS/CSTLS Series
Type
fosc.
a
b
c
d
e
f
G
03.40—10.00MHz
100
concrete
350±10°C
60±2°C
1000
−55±2°C
X
16.00—70.00MHz
100
concrete
350±10°C
60±2°C
1000
−55±2°C
3. CSACW Series
Type
fosc.
a
b
c
d
e
f
X
20.01—70.00MHz
100
wooden plate
—
60±2°C
1000
−55±2°C
4. CSTCC/CSTCR/CSTCE/CSTCW Series
Type
fosc.
a
b
c
d
e
f
G
02.00—12.50MHz
100
wooden plate
—
60±2°C
1000
−55±2°C
V
12.51—20.00MHz
100
wooden plate
—
60±2°C
1000
−55±2°C
X
20.01—70.00MHz
100
wooden plate
—
60±2°C
1000
−55±2°C
19
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
3
Specifications of CERALOCK®
(%)
0.1
1. Shock Resistance
(%)
0.1
0.05
0.05
fosc. 0
after test
(%)
0.1
3. Vibration Resistance
(%)
0.1
0.05
fosc. 0
before test
fosc. 0
before test
after test
fosc. 0
before test
after test
-0.05
-0.05
-0.1
-0.1
-0.1
-0.1
(%)
0.1
6. Storage at Low Temperature
0.05
0.05
100
1000
(%)
0.1
1000
(time)
-0.05
-0.05
-0.1
-0.1
-0.1
8. Terminal Strength
fosc. 0
25
-0.05
(time)
0.05
fosc. 0
100
(time)
7. Temperature Cycling
0.05
fosc. 0
fosc. 0
(%)
0.1
1000
100
-0.05
5. Storage at High Temperature
4. Humidity Resistance
0.05
-0.05
(%)
0.1
3
2. Solder Heat Resistance
50
100
(cycle)
before test
after test
-0.05
-0.1
Fig. 3-2 General Changes of Oscillation Frequency in Each Reliability Test (CSTLS4M00G53–B0)
!Deviation after Reliability Test
Every Series
∗ CSTCC Series : within±0.3%
Oscillation
Frequency
Others
within±0.2%*
(from initial value)
Meets the individual
specification of each
product.
Peak
(240D max.)
Temperature (D)
Item
Type
230
Heating
(230D)
180
150
Pre-heating
(150-180D)
Gradual
Cooling
30 sec. min.
60-120 sec.
40 sec. max. 120 sec. min.
Fig. 3-3 Reflow Soldering Profile for MHz Band Chip
CERALOCK®
20
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
4 Applications of Typical Oscillation Circuits
As described in Chapter 2, the most common oscillation
circuit with CERALOCK® is to replace L of a Colpitts
circuit with CERALOCK®. The design of the circuit
varies with the application and the IC being used, etc.
Although the basic configuration of the circuit is the
same as that of a quartz crystal, the difference in
mechanical Q results in the difference of the circuit
constant.
This chapter briefly describes the characteristics of the
oscillation circuit and gives some typical examples.
1. Cautions for Designing Oscillation Circuits
It is becoming more common to configure the oscillation
circuit with a digital IC, and the simplest way to use an
inverter gate.
Fig. 4-1 shows the configuration of a basic oscillation
circuit with a C-MOS inverter.
INV. 1 works as an inverter amplifier of the oscillation
circuit. INV. 2 acts to shape the waveform and also acts
as a buffer for the connection of a frequency counter.
The feedback resistance Rf provides negative feedback
around the inverter in order to put it in the linear
region, so the oscillation will start, when power is
applied.
If the value of Rf is too large, and if the insulation
resistance of the input inverter is accidentally
decreased, oscillation will stop due to the loss of loop
gain. Also, if Rf is too great, noise from other circuits
can be introduced into the oscillation circuit.
Obviously, if Rf is too small, loop gain will be low. An Rf
of 1MΩ is generally used with a ceramic resonator.
Damping resistor Rd provides loose coupling between
the inverter and the feedback circuit and decreases the
loading on the inverter, thus saving energy.
In addition, the damping resistor stabilizes the phase of
the feedback circuit and provides a means of reducing
the gain in the high frequency area, thus preventing the
possibility of spurious oscillation.
Load capacitance CL1 and CL2 provide the phase lag of
180°.
The proper selected value depends on the application,
the IC used, and the frequency. If CL1 and CL2 values
are too low, the loop gain in the high frequency is
increased, which in turn increases the probability of
spurious oscillation.
This is particularly likely around 4 to 5 MHz, where the
thickness vibration mode lies, as shown in Fig. 2-5 when
using kHz band resonator.
VDD
INV.1
INV.2
IC
4
Output
IC
Rf=1MΩ
Rd
X
CL1
CL2
IC : 1/6CD4069UBE
X : CERALOCK®
CL1, CL2 : External Capacitance
Rd : Dumping Resistor
Fig. 4-1 Basic Oscillation Circuit with C-MOS Inverter
21
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
4
Application to Typical Oscillation Circuit
Oscillation frequency fosc. in this circuit is expressed
approximately by the following equation.
fosc.=Fr
1+
C1
C0+CL
(4-1)
Where, Fr=Resonance frequency of CERALOCK®
Where, C1 : Equivalent series capacitance of
Where, C1 : CERALOCK®
Where, C0 : Equivalent parallel capacitance of
Where, C1 : CERALOCK®
CL1 · CL2
Where,
CL=
Where, = L= CL1+CL2
This clearly shows that the oscillation frequency is
influenced by the loading capacitance. And caution
should be paid in defining its value when a tight
tolerance of oscillation frequency is required.
4
2. Application to Various Oscillation Circuits
Application to C-MOS Inverter
For the C-MOS inverting amplifier, the one-stage 4069
C-MOS group is best suited.
The C-MOS 4049 type is not used, because the threestage buffer type has excessive gain, which causes RC
oscillation and ringing.
Murata employs the RCA (HARRIS) CD4069UBE as a
C-MOS standard circuit. This circuit is shown in
Fig. 4-2. The oscillation frequency of the standard
CERALOCK® (C-MOS specifications) is adjusted by the
circuit in Fig. 4-2.
VDD
Item
14
Frequency Rage
Part Number
IC : CD4069UBE (RCA) ∗
1
2 3
4
VDD
375—0429kHz
7
CSBLA Series
Rf
CERALOCK® Rd
430—0699kHz
1+5V
700—1250kHz
Circuit Constant
CL1
CL2
120pF
470pF
1MΩ
Rf
Rd
100pF
100pF
1MΩ
0
100pF
100pF
1MΩ
5.6kΩ
(15pF)
(15pF)
1MΩ
0
0
Output
CL1
CL2
CSTLS- G53
03.40—10.00MHz
1+5V
∗CSTLS-G53 series : TC4069UBP
Fig. 4-2 C-MOS Standard Circuit
22
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Application to Typical Oscillation Circuit
4
Application to H-MOS Inverter
Recently, high speed C-MOS (H-CMOS) have been used
more frequently for oscillation circuits allowing high
speed and energy saving control for the microprocessor.
There are two types of H-CMOS inverters: the unbuffered 74HCU series and the 74HC series with
buffers.
The 74HCU system is optimum for the CERALOCK®
oscillation circuit.
Fig. 4-3 shows our standard H-CMOS circuit.
Since H-CMOS has high gain, especially in the high
frequency area, greater loading capacitor (CL) and
damping resistor (Rd) should be employed to stabilize
oscillation performance. As a standard circuit, we
recommend Toshiba's TC74CU04, but any 74HCU04
inverter from other manufacturers may be used.
The oscillation frequency for H-CMOS specifications is
adjusted by the circuit in Fig. 4-3.
4
Item
VDD (+5V)
Frequency Rage
14
IC : TC74HCU04 (TOSHIBA)*
1
2 3
4
CSBLA- E (J)
7
Rf
CL2
Rf
Rd
0375~0429kHz
330pF
330pF
1MΩ
5.6kΩ
0430~0699kHz
220pF
220pF
1MΩ
5.6kΩ
0700~0999kHz
150pF
150pF
1MΩ
5.6kΩ
1000~1250kHz
100pF
100pF
1MΩ
5.6kΩ
CSTLS- G56
03.40~10.00MHz
(47pF)
(47pF)
1MΩ
680Ω
CSALS- X55
16.00~19.99MHz
30pF
30pF
1MΩ
0
CSALS- X53
20.00~25.99MHz
15pF
15pF
1MΩ
0
CSALS- X51
26.00~70.00MHz
5pF
5pF
1MΩ
0
CERALOCK® Rd
Output
CL1
Circuit Constant
CL1
Part Number
CL2
∗ 60.01—70.00MHz : SN74AHCU04
Fig. 4-3 H-CMOS Standard Circuit
23
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
4
P17E14.pdf 04.8.24
Application to Typical Oscillation Circuit
Application to Transistors and Comparators
Fig. 4-4 shows examples of the configuration for a
Colpitts type oscillation circuit with a transistor.
Load capacitance used is larger than in the case of a
MOS inverter.
Fig. 4-5 shows an example with a comparator IC. The
oscillation circuit is configured by using the invert input
side. Loading capacitance and feedback resistance are
almost the same as those for a MOS-IC.
30kΩ
0.0047µF
+10V
Output
1kΩ
0.001µF
CSBLA455KEC8–B0
Fig. 4-4 Example of Oscillation Circuit with a Transistor
+5V
220kΩ
4
220kΩ
1kΩ
+
Output
LM339
100kΩ
5.6kΩ
CERALOCK®
C1
Ex.
C2
CERALOCK®
C1
C2
CSBLA400KECE–B0
120pF
120pF
Fig. 4-5 Example of Application to a Comparator
24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
5 Characteristics of CERALOCK® Oscillation Circuit
This chapter describes the general characteristics of the basic
oscillation of Fig. 4-1 (page. 21). Contact Murata for detailed
characteristics of oscillation with specific kinds of ICs and LSIs.
1. Stability of Oscillation Frequency
Fig. 5-1 shows examples of actual measurements for stability
of the oscillation frequency.
The stability versus temperature change is ±0.1 to 0.5% within
a range of -20 to +80°C, although varies slightly depending on
the ceramic material.
Influence of load capacitance (CL1, CL2) on the oscillation
frequency is relatively high, as seen in formula (4-1) (P.22).
It varies approximately ±0.05% for a capacitance deviation of
±10%. The stability versus supply voltage is normally within
±0.05% in the working voltage range, although it varies with
the characteristics of the IC.
Temperature Characteristics
Supply Voltage Characteristics
Max.
Min.
0
-40
0
40
80
120
Temperature (°C)
-0.25
CL2 (CL1 = Constant) Characteristics
+0.50
VDD = +5V
CL1 = 6pF Const.
+0.25
0
2
4
6
8
VDD (V)
-0.25
Starting Voltage
-0.50
+0.25
CL1 (CL2 = Constant) Characteristics
+0.50
0
0
1
VDD = +5V
CL2 = 6pF Const.
10
CL2/CL1
Oscillating Frequency Shift (%)
Oscillating Frequency Shift (%)
5
+0.25
-0.50
-0.25
-0.50
CL (CL1 = CL2) Characteristics
+0.50
Oscillating Frequency Shift (%)
+0.50
VDD = +5V
Oscillating Frequency Shift (%)
Oscillating Frequency Shift (%)
+0.50
VDD = +5V
0
0
1
10
CL1/CL2
-0.25
-0.50
+0.25
0
+0.25
0
1
100
10
CL (pF)
-0.25
-0.50
Fig. 5-1 Examples of Actual Measurement for the Stability of Oscillation Frequency (IC: TC74HCU04, CERALOCK®: CSACW33M8X51–B0)
25
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
5
P17E14.pdf 04.8.24
Characteristics of CERALOCK® Oscillation Circuit
2. Characteristics of the Oscillation Level
Fig. 5-2 shows examples of actual measurements of the
oscillation level versus temperature, supply voltage and
load capacitance (CL1, CL2). The oscillating amplitude is
required to be stable over a wide temperature range,
and temperature characteristics should be as flat as
possible. The graph titled Supply Voltage
Characteristics in Fig. 5-2 shows that the amplitude
varies linearly with supply voltage, unless the IC has an
internal power supply voltage regulator.
Temperature Characteristics of Oscillationg Voltage
V1H
4
3
2
1
V1L
0
-40
0
40
80
-1
+9.0
V2H
+8.0
Oscillating Level (V)
Oscillating Level (V)
5
5
Oscillating Voltage vs VDD Characteristics
VDD = +5V
V2H
6
+7.0
V1H
+6.0
+5.0
+4.0
+3.0
+2.0
V1L
+1.0
0
-1.0
120 V2L
Temperature (°C)
2
CL2 (CL1 = Constant) Characteristics
+7.0
V2L
8
VDD (V)
CL1 (CL2 = Constant) Characteristics
V1H
V2H
VDD = +5V
CL2 = 6pF Const.
+6.0
V2H
+5.0
+5.0
Oscillating Level (V)
Oscillating Level (V)
6
+7.0
VDD = +5V
CL1 = 6pF Const.
+6.0
4
+4.0
+3.0
+2.0
+1.0
V1H
+4.0
+3.0
+2.0
V1L
+1.0
0
1
0
V2L
V1L
-1.0
0
10
CL2/CL1
1
0
V2L
10
CL1/CL2
-1.0
CL (CL1 = CL2) Characteristics
+7.0
VDD = +5V
+6.0
V2H
V1H
Oscillating Level (V)
+5.0
+4.0
+3.0
+2.0
+1.0
0
0
1
10
V1L
V2L
100
CL (pF)
-1.0
Fig. 5-2 Examples of Actual Measurement of Oscillating Amplitude (IC: TC74HCU04, CERALOCK®: CSACW33M8X51–B0)
26
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
5
Characteristics of CERALOCK® Oscillation Circuit
3. Characteristics of Oscillation Rise Time
ON
Supply Voltage Characteristics
1.00
Rise Time (ms)
Oscillation rise time means the time when oscillation
develops from a transient area to a steady state
condition, at the time the power of the IC is activated.
With a CERALOCK®, this is defined as the time to reach
90% of the oscillation level under steady state
conditions as shown in Fig. 5-3.
Rise time is primarily a function of the oscillation circuit
design. Generally, smaller loading capacitance, higher
frequency of ceramic resonator, and lower mechanical Q
of ceramic resonator cause a faster rise time. The effect
of load capacitance becomes more apparent as the
capacitance of the resonator decreases.
Fig. 5-4 shows how the rise time increases as the load
capacitance of the resonator increases. Also, Fig. 5-4
shows how the rise time varies with supply voltage.
It is noteworthy that the rise time of the ceramic
resistor is one or two decades faster than a quartz
crystal.
Fig. 5-5 shows comparison of rise time between the two.
0.50
0
2
4
6
VDD (V)
8
CL (CL1 = CL2) Characteristics
1.00
5
VDD = +5V
Rise Time (ms)
VDD
0V
0.9×Vp-p
0.50
Vp-p
t=0
Rise Time
Time
0
0
1
10
CL (pF)
100
Fig. 5-3 Definition of Rise Time
Fig. 5-4 Examples of Characteristics of Oscillation Rise Time
(IC: TC74HCU04, CERALOCK®: CSACW33M8X51–B0)
CRYSTAL
(33.868MHz)
CSACW33M8X51–B0
IC : TC74HCU04AP
VDD=+5V, CL1=CL2=6pF
↑ 2.0V/div.
→0.1msec./div.
Fig. 5-5 Comparison of the Rise Time of
a Ceramic Resonator vs. a Quartz Crystal
27
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
5
Characteristics of CERALOCK® Oscillation Circuit
4. Starting Voltage
5.0
VDD = +5V
4.0
Starting Voltage (V)
Starting voltage means the minimum supply voltage at
which an oscillation circuit can operate. Starting voltage
is affected by all the circuit elements, but it is
determined mostly by the characteristics of the IC.
Fig. 5-6 shows an example of an actual measurement for
the starting voltage characteristics against the loading
capacitance.
3.0
2.0
1.0
0
0
1
10
CL (pF)
100
Fig. 5-6 Starting Voltage Characteristics against CL (CL1=CL2)
(IC: TC74HCU04, CERALOCK®: CSACW33M8X51–B0)
5
28
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
6 Application Circuits to Various ICs/LSIs
CERALOCK®, by making good use of the above mentioned features, is used in a
wide range of applications to various kinds of ICs.
The following are a few examples of actual applications.
1. Application to Microcomputers
CERALOCK® is optimum for a stable oscillation element
for various kinds of microcomputers : 4-bit, 8-bit and
16-bit.
With the general frequency tolerance required for the
reference clock of microcomputers at ±2 to ±3%,
standard CERALOCK® meets this requirement. Please
consult with MURATA or LSI manufacturers about the
circuit constants, because these constants vary with
frequency and the LSI circuit being used.
Fig. 6-1 to 6-6 show applications to various kinds of
4-bit microcomputers, Fig. 6-7 to 6-12 show application
to 8-bit microcomputers, and Fig. 6-13 to 6-15 show
application to 16bit and 32bit microcomputers.
VDD (+5V)
4, 12
IC : MN15G1601
8
13
9
CSTLS4M00G56–B0
C1
C1=47pF
C2=47pF
C2
Fig. 6-1 Application to MN15G1601 (MATSUSHITA)
VDD (+5V)
6
28
IC : TMP47C443N
2
3-27
1
CSTCR4M00G53–R0
C1
C2
C1=15pF
C2=15pF
Fig. 6-2 Application to TMP47C443N (TOSHIBA)
VDD (+5V)
25
IC : M34524MC–xxxFP
22
23
L
CSTCR4M00G53–R0
C1
C2
C1=15pF
C2=15pF
L : 21, 24, 28, 29
Fig. 6-3 Application to M34524MC-xxxFP (MITSUBISHI)
29
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
6
Application Circuits to Various ICs/LSIs
VDD (+5V)
VDD (+5V)
28
6, 20, 21
IC : TMP87C809BN
IC : HD4074318S
8
9
7, 10, 11, 22, 23
2
14, 27
1
Rf
CSTLS4M00G53–B0
C1
CSTLS8M00G53–B0
Rf=1MΩ
C1=15pF
C2=15pF
C2
Fig. 6-4 Application to HD4074318S (HITACHI)
C1
C1=15pF
C2=15pF
C2
Fig. 6-7 Application to TMP87C809BN (TOSHIBA)
VDD (+5V)
VDD (+5V)
28
21, 24
IC : MC68HC05P18ADW
IC : µPD753108
22
23
27
L
26
CSTLS4M19G53–B0
CSTLS4M00G56–B0
C1
6
C1=47pF
C2=47pF
L : 2, 3, 4, 9, 18, 19
C2
Fig. 6-5 Application to µPD753108 (NEC)
VDD (+5V)
C1
VDD (+5V)
10kΩ
27,28
10, 24, 25
IC : LC65F1156A
8
36
IC : µPD780032A
L
9
41
40
CSTLS4M00G56–B0
C1
C2
9, 25, 42
CSTCE8M00G52-R0
C1=47pF
C2=47pF
L : 1–7, 16–20, 25, 26, 29,
30
Fig. 6-6 Application to LC65F1156A (SANYO)
30
Rf=1MΩ
C1=39pF
C2=39pF
C2
Fig. 6-8 Application to MC68HC05P18ADW (MOTOROLA)
1kΩ
10
14
Rf
C1
C2
C1=10pF
C2=10pF
Fig. 6-9 Application to µPD780032A (NEC)
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Application Circuits to Various ICs/LSIs
VDD (+5V)
VDD (+5V)
16, 61
H
IC : HD6433802
6
IC : HD64F2268
4, 7, 8, 55
5
65
Rf
63
CSTCE16M0V53-R0
C1
L
CSTCE12M0G52-R0
C1=15pF
C2=15pF
C2
Fig. 6-10 Application to HD64F33802 (HITACHI)
C1
C1=10pF
C2=10pF
H : 12, 54, 57, 61, 62
L : 14, 42, 60, 64
C2
Fig. 6-13 Application to HD64F2268 (HITACHI)
VDD (+5V)
VDD (+5V)
40
H
16
IC : MSM83C154S
19
18
54
22
9, 20
C2
56
IC : M30221M4-xxxFP
20
L
CSTCE10M0G52-R0
CSTLS6M00G56-B0
C1
6
C1
C1=47pF
C2=47pF
Fig. 6-11 Application to MSM83C154S (OKI)
VDD (+5V)
C1=10pF
C2=10pF
H : 20, 51, 52, 76, 120
L : 13, 18, 49, 50, 53, 55,
78, 117
RESET : 16
C2
6
Fig. 6-14 Application to M30221M4-xxxFP (MITSUBISHI)
VDD (+3.3V)
57
H
IC : M38039MF-xxxFP
22
23
IC : µPD70F3102
18, 19, 24, 58, 59
64
63
CSTCR6M60G55–R0
CSTLS8M00G53–B0
C1
C2
L
C1=15pF
C2=15pF
Fig. 6-12 Application to M38039MF-xxxFP (MITSUBISHI)
C1
C2
C1=39pF
C2=39pF
H : 34, 45, 62, 100, 126, 144
L : 9, 35, 65, 71, 83, 117, 135
Fig. 6-15 Application to µPD70F3102 (NEC)
31
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
6
P17E14.pdf 04.8.24
Application Circuits to Various ICs/LSIs
2. Application to Remote Control ICs
Remote controllers have become an increasingly more
popular feature in TVs, stereos, VCRs, and air
conditioners.
Fig. 6-16, 6-17 show examples of CERALOCK® in
remote control transmission ICs. Oscillation frequency
is normally 3.2M to 4MHz, with 3.64MHz being the
most popular. This 3.64MHz is divided by a carrier
signal generator, so that a carrier of approximately
38kHz is generated.
VDD (+3V)
H
IC : µPD65
8
7
L
CSTLS3M64G53–B0
C1
C1=15pF
C2=15pF
H : 6, 10
L : 3, 9, 12, 13, 14
C2
Fig. 6-16 Application to µPD65 (NEC)
VDD (+3V)
20
IC : M34280M1
6
4
5
1
CSTLS3M64G53–B0
C1
C2
C1=15pF
C2=15pF
Fig. 6-17 Application to M34280M1 (MITSUBISHI)
32
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Application Circuits to Various ICs/LSIs
6
3. Application to Various Kinds of VCOs (Voltage Controlled Oscillators)
0.022µF
47µF
VCC (+9V)
+
25, 44
IC : TA8690AN
20
510kΩ
Vcont.
22
8
37
430Ω
24
FH (1/32fosc.)
390Ω
23
CSBLA503KEZZF46–B0
150Ω
VCO circuits are used in TVs and audio equipment,
because the signals need to be processed in
synchronization with pilot signals transmitted from
broadcasting stations. Oscillation circuits, such as LC
and RC, were previously often used, but CERALOCK® is
now widely used as well, because they require no
adjustment and have superior stability over the older
type circuit.
Resonators, for VCO applications, are required to have a
wide variable frequency range. We supply CERALOCK®
devices with specially designed ceramic materials for
VCO applications.
Fig. 6-18 Application to TA8690AN (TOSHIBA)
Application to TV Horizontal Oscillation
Circuits
Fig. 6-18 to 6-20 show application examples of horizontal
oscillation circuits.
Fig. 6-18 and 6-19 are examples of NTSC system
(FH=15.734kHz) and Fig. 6-20 is for PAL system
(FH=15.625kHz).
48
44
100µF
0.01µF
VCC (+7.8V)
+
40
IC : LA7687
23
24
1.8kΩ
+
0.033µF
6
25
330kΩ
22
CSBLA503
KEZZF12–B0
15
22µF
+
3.3µF
Vcont.
HVcc 13mA
Hout (fosc./32)
Fig. 6-19 Application to LA7687 (SANYO)
VCC (+12V)
1kΩ
11
13
IC : TEA2130
17
3
9
18
4
100nF
3.32kΩ
33nF
Rs
Vcont.
2.2µF 3.9kΩ
CSBLA503KEZZF12–B0
5
2.7kΩ
Flyback In
47nF
100µF
0.01µF
Hout
Rs=470Ω
Fig. 6-20 Application to TEA2130 (THOMSON)
33
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
6
Application Circuits to Various ICs/LSIs
Application to Stereo Demodulation Circuits
1kΩ
3.3µF
0.47µF
16 15
14 13
350kΩ
10µF
(VCO STOP)
CSBLA456KE2ZF11–B0
Fig. 6-21 is an application to the FM-MPX.
VCC
−
+
1µF
12
11
10
9
7
8
LA3410
1
0.047µF
2
3
4
VCC (+12V)
62kΩ
5
750pF
INPUT
6
62kΩ
750pF
L
R
Fig. 6-21 Application to LA3410 (SANYO) (FM-MPX)
4. Application to Telephone Dialers
6
The latest developments in telephone technology make it
a highly advanced communication terminal. With the
change from the pulse dialer to the tone dialer, the
telephone key pad can be used for an effective data
transmission. The frequency tone of each key is
determined by the combination of the allocated frequency
tone of the column and row keys. It is mandatory to
observe an overall frequency tolerance of ±1.5% under any
servicing conditions. Since ICs normally have a division
error of ±0.1 to ±0.75%, a maximum of ±0.6% frequency
tolerance is allowed for the oscillator of the tone dialer.
HIGH GROUP
FREQUENCIES (Hz)
1209
1336
1477
1633
697
1
2
3
A
770
4
5
6
B
852
7
8
9
C
0
#
D
LOW GROUP
FREQUENCIES
(Hz)
941
Fig. 6-22 Key Matrix
34
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
Application Circuits to Various ICs/LSIs
In order to satisfy this frequency accuracy, we developed
the 3.58MHz CERALOCK® “CSTLS3M58GD series”
which is tuned for each IC.
Due to the outstanding features of CERALOCK® such as
lower cost, lighter weight, and faster rise-up time, it is
widely replacing the quartz crystal.
Fig. 6-23, Fig. 6-24 are some examples for various dialer
ICs. For more information, “Piezoelectric Components
Application Manual for the New Telephone” is available
upon request.
6
VDD (+5V)
H
2
21
IC : LC7367JM
9
L
10
CSTLS3M58GD6267–B0
C1
C1=47pF
C2=47pF
H : 11
L : 5, 6, 7, 8, 12
C2
Fig. 6-23 Application to LC7367J (SANYO) (Tone-Pulse Dialer)
VDD (+5V)
1
IC : ML7005MB
11
12
23
CSTLS3M58GD3104
C1
C2
C1=15pF
C2=15pF
6
Fig. 6-24 Application to ML7005MB (OKI) (Tone-Pulse Dialer)
35
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
6
Application Circuits to Various ICs/LSIs
5. Application to ICs for Office Equipments
With the applications of ICs in office machines, many
CERALOCK®s are used for motor drivers/controllers/
digital signal processor (D.S.P.) in floppy disk driver
(F.D.D.) and CD/CD-ROM's ICs. Fig. 6-25, 6-26 show
application examples. It is believed that this type of
application will increase in the future.
VDD1 (+5V) VDD2 (+3.3V)
H1
H2
IC : LC895299
93
L
92
Rf
CSTCW33M8X53–R0
C1
C2
C1=15pF
C2=15pF
H1 : 21, 39, 52, 65, 86, 88,
94, 112, 154, 163, 176
H2 : 22, 44, 66, 110, 116,
132, 165
L : 1, 23, 24, 40, 45, 51, 58,
67, 73, 89, 91, 109, 111,
125, 133, 139, 155, 164
Fig. 6-25 Application to LC895299 (SANYO)
(Error Correction of CD-ROM LSI)
VDD1 (+5V)
VDD2 (+3.3V)
H2
H1
IC : LC78646E
6
49
L
48
Rd
CSTCE16M9V53–R0
C1
C2
Rd=150Ω
C1=15pF
C2=15pF
H1 : 5, 18, 38, 41, 46,
47, 77
H2 : 68
L : 6, 19, 37, 43, 44, 51,
69, 75
Fig. 6-26 Application to LC78646E (SANYO)
(CD Digital Signal Processor)
36
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Application Circuits to Various ICs/LSIs
6
6. Other Kinds of Applications to Various ICs
VDD (+5V)
8, 9
IC : MSM6650GS
8
GND
9
220pF
Other than the above mentioned uses, CERALOCK® is
widely used with ICs for voice synthesis.
Fig. 6-27 and 6-28 show examples of voice synthesis.
We can provide CERALOCK® application data for many
ICs which are not mentioned in this manual. Please
consult us for details.
CSTLS4M09G53–B0
C1
C2
C1=15pF
C2=15pF
: 15, 29, 64
GND : 6, 7, 14, 16, 20
Fig. 6-27 Application to ICs for Voice Synthesis MSM6650GS (OKI)
VDD (+5V)
6
IC : LC81192
25
26
1
1MΩ
CSBLA400KECE–B0
330pF
4.7kΩ
330pF
6
Fig. 6-28 Application to ICs for Voice Synthesis LC81192 (SANYO)
37
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
7 Notice
!Notice (Soldering and Mounting)
Please consult with us regarding ultrasonic cleaning
conditions to avoid possible damage during ultrasonic
cleaning.
!Notice (Storage and Operating Conditions)
· Please do not apply excess mechanical stress to the
component and lead terminals at soldering.
· Conformal coating of the component is acceptable.
However, the resin material, curing temperature, and
other process conditions should be evaluated to
confirm stable electrical characteristics are
maintained.
!Notice (Rating)
The component may be damaged if excess mechanical
stress is applied.
!Notice (Handling)
7
· Unstable oscillation or oscillation stoppage might
happen when CERALOCK® is used in an improper
way in conjunction with ICs. We are happy to evaluate
the application circuit to avoid this for you.
· Oscillation frequency of our standard CERALOCK® is
adjusted with our standard measuring circuit. There
could be slight shift in frequency other types of IC are
used. When you require exact oscillation frequency in
your application, we can adjust it with your specified
circuit.
38
P17E14.pdf 04.8.24
P17E14.pdf 04.8.24
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
8
Appendix
Equivalent Circuit Constants of CERALOCK®
(The equivalent circuit constants are not the guaranteed value but the standard value.)
Equivalent
Constant
Fr (kHz)
Fa (kHz)
∆F (kHz)
R1 (Ω)
L1 (mH)
C1 (pF)
C0 (pF)
CSBLA400KECE-B0
388.5
402.4
13.9
6.2
6.7041
25.0462
344.3647
2650
CSBLA455KEC8-B0
443.9
457.3
13.4
10.1
7.6800
16.7421
272.7610
2136
CSBLA500KEC8-B0
487.2
503.2
16.0
8.5
7.1632
14.9069
222.8248
2619
CSBLA600KEC8-B0
586.5
604.2
17.7
11.8
6.1860
11.9121
194.2629
2140
CSBLA700KJ58-B0
683.5
706.5
23.0
11.1
5.3876
10.0678
146.8621
2158
CSBLA1M00J58-B0
978.5
1013.3
34.7
13.7
4.4407
5.9576
82.4807
2009
CSBLA1M20J58-B0
1179.6
1220.8
41.2
45.4
4.5330
4.0184
56.4891
780
436.6
457.9
21.2
11.4
4.1631
31.9247
320.3785
1006
CSBLA456KE2ZF14-B0
435.9
457.4
21.5
11.0
3.9472
33.7848
333.5176
989
CSBLA500KECZF02-B0
506.1
549.8
43.7
8.5
1.3209
74.8959
415.5858
496
CSBLA500KECZF09-B0
489.0
543.9
55.0
27.9
0.9089
116.5686
490.9133
100
CSBLA503KECZF02-B0
509.5
554.0
44.6
8.5
1.2460
78.3331
429.0170
474
CSTLS4M00G53-B0
3784.4
4135.3
350.9
9.0
0.4611
3.8377
19.7730
1220
CSTLS6M00G53-B0
5710.9
6199.5
488.6
7.5
0.2381
3.2635
18.2899
1135
CSTLS8M00G53-B0
7604.7
8246.3
641.6
8.0
0.1251
3.5030
19.9175
775
CSTLS10M0G53-B0
9690.1
10399.1
709.0
7.0
0.0984
2.7448
18.0899
947
CSTLS16M0X55-B0
15972.9
16075.0
102.1
24.6
0.6572
0.1511
11.7835
2681
CSTLS20M0X53-B0
19959.2
20070.8
111.6
19.0
0.4858
0.1309
11.6716
3203
CSTLS24M0X53-B0
23955.8
24095.9
140.2
16.6
0.4205
0.1050
8.9440
3805
CSTLS27M0X51-B0
27024.3
27172.8
148.5
15.9
0.3638
0.0953
8.6486
3877
CSTLS32M0X51-B0
31918.4
32092.6
174.2
13.4
0.2481
0.1002
9.1542
3716
CSTLS33M8X51-B0
33777.8
33969.7
191.9
25.6
0.2561
0.0867
7.6093
2120
CSTLS36M0X51-B0
36033.6
36241.1
207.6
13.4
0.2260
0.0863
7.4700
3821
CSTLS40M0X51-B0
39997.7
40240.1
242.7
15.8
0.2301
0.0688
5.6544
3651
CSTLS50M0X51-B0
49946.3
50193.1
246.8
27.6
0.1856
0.0547
5.5234
2107
Qm
Part Number
CSBLA456KE2ZF11-B0
8
39
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
P17E14.pdf 04.8.24
Note:
1. Export Control
For customers outside Japan
Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructive
weapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons.
For customers in Japan
For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required
for export.
<
<
>
>
2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially
high reliability for the prevention of defects which might directly damage to a third party's life, body or property, or when one of our products is intended for use
in applications other than those specified in this catalog.
q Aircraft equipment
w Aerospace equipment
e Undersea equipment
r Power plant equipment
t Medical equipment
y Transportation equipment (vehicles, trains, ships, etc.)
u Traffic signal equipment
i Disaster prevention / crime prevention equipment
o Data-processing equipment
!0 Application of similar complexity and/or reliability requirements to the applications listed in the above
3. Product specifications in this catalog are as of July 2004. They are subject to change or our products in it may be discontinued without advance notice. Please
check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product
engineers.
4. Please read rating and
CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or
transact the approval sheet for product specifications before ordering.
6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect
of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or
contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned
above under licenses without our consent.
7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process.
http://www.murata.com/
Head Office
2-26-10, Tenjin Nagaokakyo-shi, Kyoto 617-8555, Japan Phone: 81-75-951-9111
As of October 12, 2004, Murata's contact information will be changed as follows
1-10-1, Higashi Kotari, Nagaokakyo-shi, Kyoto 617-8555, Japan
International Division
3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan
Phone: 81-3-5469-6123 Fax: 81-3-5469-6155 E-mail: [email protected]