TC74VCX16835FT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74VCX16835FT Low-Voltage 18-Bit Universal Bus Driver with 3.6-V Tolerant Inputs and Outputs The TC74VCX16835FT is a high-performance CMOS 18-bit universal bus driver. Designed for use in 1.8-V, 2.5-V or 3.3-V systems, it achieves high-speed operation while maintaining the CMOS low power dissipation. It is also designed with overvoltage tolerant inputs and outputs up to 3.6 V. Data flow from A to Y is controlled by the output-enable (OE) input. The device operates in the transparent mode when the latch-enable (LE) input is high. When LE is low, the A data is Weight: 0.25 g (typ.) latched if the clock (CK) input is held at a high or low logic level. If LE is low, the A data is stored in the latch/flip-flop on the low-to-high transition of CK. When OE is high, the outputs are in the high-impedance state. All inputs are equipped with protection circuits against static discharge. Features • Low-voltage operation: VCC = 1.8 to 3.6 V • High-speed operation: tpd = 3.3 ns (max) (VCC = 3.0 to 3.6 V) : tpd = 4.2 ns (max) (VCC = 2.3 to 2.7 V) : tpd = 8.4 ns (max) (VCC = 1.8 V) • Output current : IOH/IOL = ±24 mA (min) (VCC = 3.0 V) : IOH/IOL = ±18 mA (min) (VCC = 2.3 V) : IOH/IOL = ±6 mA (min) (VCC = 1.8 V) • Latch-up performance: −300 mA • ESD performance: Machine model ≥ ±200 V Human body model ≥ ±2000 V • Package: TSSOP • 3.6-V tolerant function and power-down protection is provided on all inputs and outputs 1 2007-10-19 TC74VCX16835FT Pin Assignment (top view) NC 1 IEC Logic Symbol 56 OE GND NC 2 55 NC Y1 3 54 A1 GND 4 53 GND CK LE 27 30 28 EN1 2C3 C3 G2 Y2 5 52 A2 Y3 6 51 A3 VCC 7 50 8 49 A4 Y5 9 48 A5 Y6 10 47 A6 GND 11 46 GND Y7 12 45 A7 Y8 13 44 A8 Y9 14 43 A9 Y10 15 42 A10 Y11 16 41 A11 Y12 17 40 A12 GND 18 39 GND Y13 19 38 A13 Y14 20 37 A14 Y15 21 36 A15 22 35 VCC Y16 23 34 A16 Y17 24 33 A17 GND 25 32 GND Y18 26 31 A18 27 30 CK LE 28 29 GND OE Y2 Y3 Y4 Y5 Y6 VCC Y4 VCC Y1 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 2 3 5 1 1 3D 54 52 6 51 8 49 9 48 10 12 47 13 44 14 15 43 42 16 41 17 40 19 20 38 37 21 36 23 34 24 33 26 31 45 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 2007-10-19 TC74VCX16835FT Truth Table Inputs Outputs Y OE LE CK A H X X X Z L H X L L L H X H H L L L L L L H H L L H X L L L X Y0 (Note) Y0 (Note) X: Don’t care Z: High impedance Note: Output level before the indicated steady-state input conditions were established, provided that CK was high or low before LE went low. System Diagram OE CK LE A1 27 30 28 54 LE LE D D 3 Y1 To 17 other channels 3 2007-10-19 TC74VCX16835FT Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Power supply voltage VCC −0.5 to 4.6 V DC input voltage VIN −0.5 to 4.6 V −0.5 to 4.6 (Note 2) DC output voltage VOUT −0.5 to VCC + 0.5 V (Note 3) Input diode current −50 IIK mA Output diode current IOK ±50 DC output current IOUT ±50 mA Power dissipation DC VCC/ground current per supply pin Storage temperature (Note 4) mA PD 400 mW ICC/IGND ±100 mA Tstg −65 to 150 °C Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: OFF state Note 3: High or low state. IOUT absolute maximum rating must be observed. Note 4: VOUT < GND, VOUT > VCC Operating Ranges (Note 1) Characteristics Symbol Power supply voltage VCC Input voltage VIN Output voltage Output current Rating Unit 1.8 to 3.6 1.2 to 3.6 (Note 2) −0.3 to 3.6 V 0 to 3.6 (Note 3) VOUT 0 to VCC (Note 4) IOH/IOL ±24 (Note 5) ±18 (Note 6) ±6 (Note 7) Operating temperature Topr −40 to 85 Input rise and fall time dt/dv 0 to 10 V V mA °C (Note 8) ns/V Note 1: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Note 2: Data retention only Note 3: OFF state Note 4: High or low state Note 5: VCC = 3.0 to 3.6 V Note 6: VCC = 2.3 to 2.7 V Note 7: VCC = 1.8 V Note 8: VIN = 0.8 to 2.0 V, VCC = 3.0 V 4 2007-10-19 TC74VCX16835FT Electrical Characteristics DC Characteristics (Ta = −40 to 85°C, 2.7 V < VCC =< 3.6 V) Characteristics Input voltage Symbol Test Condition H-level VIH ⎯ L-level VIL ⎯ H-level VOH Min Max 2.7 to 3.6 2.0 ⎯ 2.7 to 3.6 ⎯ 0.8 IOH = −100 μA 2.7 to 3.6 VCC − 0.2 ⎯ IOH = −12 mA 2.7 2.2 ⎯ IOH = −18 mA 3.0 2.4 ⎯ IOH = −24 mA 3.0 2.2 ⎯ IOL = 100 μA 2.7 to 3.6 ⎯ 0.2 IOL = 12 mA 2.7 ⎯ 0.4 IOL = 18 mA 3.0 ⎯ 0.4 IOL = 24 mA 3.0 ⎯ 0.55 2.7 to 3.6 ⎯ ±5.0 μA 2.7 to 3.6 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 2.7 to 3.6 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 2.7 to 3.6 ⎯ ±20.0 VIH = VCC − 0.6 V 2.7 to 3.6 ⎯ 750 Min Max VIN = VIH or VIL Output voltage L-level VOL Input leakage current IIN 3-state output OFF state current IOZ Power-off leakage current IOFF Quiescent supply current ICC Increase in ICC per input ΔICC VIN = VIH or VIL VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V VCC (V) Unit V V μA DC Characteristics (Ta = −40 to 85°C, 2.3 V =< VCC =< 2.7 V) Characteristics Input voltage Symbol Test Condition H-level VIH ⎯ 2.3 to 2.7 1.6 ⎯ L-level VIL ⎯ 2.3 to 2.7 ⎯ 0.7 2.3 to 2.7 VCC − 0.2 ⎯ IOH = −6 mA 2.3 2.0 ⎯ IOH = −12 mA 2.3 1.8 ⎯ IOH = −18 mA 2.3 1.7 ⎯ IOL = 100 μA 2.3 to 2.7 ⎯ 0.2 IOL = 12 mA 2.3 ⎯ 0.4 IOL = 18 mA 2.3 ⎯ 0.6 2.3 to 2.7 ⎯ ±5.0 μA 2.3 to 2.7 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 2.3 to 2.7 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 2.3 to 2.7 ⎯ ±20.0 IOH = −100 μA H-level VOH VIN = VIH or VIL Output voltage L-level VOL Input leakage current IIN 3-state output OFF state current IOZ Power-off leakage current IOFF Quiescent supply current ICC VIN = VIH or VIL VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V 5 VCC (V) Unit V V μA 2007-10-19 TC74VCX16835FT DC Characteristics (Ta = −40 to 85°C, 1.8 V =< VCC < 2.3 V) Characteristics Symbol Test Condition H-level VIH ⎯ L-level VIL ⎯ H-level VOH Min Max 1.8 to 2.3 0.7 × VCC ⎯ 1.8 to 2.3 ⎯ 0.2 × VCC IOH = −100 μA 1.8 VCC − 0.2 ⎯ IOH = −6 mA 1.8 1.4 ⎯ IOL = 100 μA 1.8 ⎯ 0.2 IOL = 6 mA 1.8 ⎯ 0.3 1.8 ⎯ ±5.0 μA 1.8 ⎯ ±10.0 μA 0 ⎯ 10.0 μA VIN = VCC or GND 1.8 ⎯ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 1.8 ⎯ ±20.0 VCC (V) Input voltage VIN = VIH or VIL Output voltage VOL VIN = VIH or VIL Input leakage current IIN VIN = 0 to 3.6 V 3-state output OFF state current IOZ Power-off leakage current IOFF Quiescent supply current ICC L-level VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V 6 Unit V V μA 2007-10-19 TC74VCX16835FT AC Characteristics (Ta = −40 to 85°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 Ω) Characteristics Maximum clock frequency Symbol fmax Propagation delay time tpLH (An-Yn) tpHL Propagation delay time tpLH (CK-Yn) tpHL Propagation delay time tpLH (LE-Yn) tpHL Output enable time Output disable time Minimum pulse width Minimum setup time (An-CK, An-LE) Minimum hold time (An-CK, An-LE) Output to output skew Note: tpZL tpZH tpLZ tpHZ tW (H) tW (L) ts th Test Condition Figure 1, Figure 3 Figure 1, Figure 2 Figure 1, Figure 3 Figure 1, Figure 4 Figure 1, Figure 5 Figure 1, Figure 5 Figure 1, Figure 3, Figure 4 Figure 1, Figure 3, Figure 4 Figure 1, Figure 3, Figure 4 tosLH tosHL Min Max 1.8 100 ⎯ 2.5 ± 0.2 200 ⎯ 3.3 ± 0.3 250 ⎯ 1.8 1.5 8.4 2.5 ± 0.2 0.8 4.2 3.3 ± 0.3 0.6 3.3 1.8 2.0 9.2 2.5 ± 0.2 1.5 5.2 3.3 ± 0.3 1.4 4.2 1.8 1.5 9.8 2.5 ± 0.2 0.8 4.9 3.3 ± 0.3 0.6 3.8 1.8 1.5 9.8 2.5 ± 0.2 0.8 4.9 3.3 ± 0.3 0.6 3.8 1.8 1.5 7.6 2.5 ± 0.2 0.8 4.5 3.3 ± 0.3 0.6 3.9 VCC (V) 1.8 4.0 ⎯ 2.5 ± 0.2 1.5 ⎯ 3.3 ± 0.3 1.5 ⎯ 1.8 2.5 ⎯ 2.5 ± 0.2 1.5 ⎯ 3.3 ± 0.3 1.5 ⎯ 1.8 1.0 ⎯ 2.5 ± 0.2 0.7 ⎯ 3.3 ± 0.3 0.7 ⎯ 1.8 ⎯ 0.5 (Note) 2.5 ± 0.2 ⎯ 0.5 3.3 ± 0.3 ⎯ 0.5 Unit MHz ns ns ns ns ns ns ns ns ns Parameter guaranteed by design. (tosLH = |tpLHm − tpLHn|, tosHL = |tpHLm − tpHLn|) 7 2007-10-19 TC74VCX16835FT AC Characteristics (Ta = 0 to 85°C, input: tr = tf = 2.0 ns, CL = 0 pF, RL = 500 Ω) Characteristics Symbol Propagation delay time tpLH (An-Yn) tpHL Propagation delay time tpLH (CK-Yn) tpHL Propagation delay time tpLH (LE-Yn) tpHL Output enable time Output disable time Minimum setup time (An-CK, An-LE) Minimum hold time (An-CK, An-LE) Note: Test Condition VCC (V) Min Max Unit Figure 1, Figure 2 (Note) 3.3 ± 0.15 0.9 2.0 ns Figure 1, Figure 3 (Note) 3.3 ± 0.15 1.5 2.9 ns Figure 1, Figure 4 (Note) 3.3 ± 0.15 0.7 2.6 ns Figure 1, Figure 5 (Note) 3.3 ± 0.15 0.7 2.6 ns Figure 1, Figure 5 (Note) 3.3 ± 0.15 0.7 2.7 ns ts Figure 1, Figure 3, Figure 4 (Note) 3.3 ± 0.15 1.5 ⎯ ns th Figure 1, Figure 3, Figure 4 (Note) 3.3 ± 0.15 0.7 ⎯ ns Min Max Unit tpZL tpZH tpLZ tpHZ TOSHIBA SPICE simulation data. AC Characteristics (Ta = 0 to 85°C, input: tr = tf = 2.0 ns, CL = 50 pF, RL = 500 Ω) Characteristics Symbol Propagation delay time tpLH (An-Yn) tpHL Propagation delay time tpLH (CK-Yn) tpHL Propagation delay time tpLH (LE-Yn) tpHL Output enable time Output disable time Minimum setup time (An-CK, An- LE) Minimum hold time (An-CK, An-LE) Test Condition VCC (V) Figure 1, Figure 2 3.3 ± 0.15 1.0 3.6 ns Figure 1, Figure 3 3.3 ± 0.15 1.7 4.5 ns Figure 1, Figure 4 3.3 ± 0.15 1.0 4.1 ns Figure 1, Figure 5 3.3 ± 0.15 1.0 4.1 ns Figure 1, Figure 5 3.3 ± 0.15 1.0 4.2 ns ts Figure 1, Figure 3, Figure 4 3.3 ± 0.15 1.5 ⎯ ns th Figure 1, Figure 3, Figure 4 3.3 ± 0.15 0.7 ⎯ ns tpZL tpZH tpLZ tpHZ 8 2007-10-19 TC74VCX16835FT Dynamic Switching Characteristics (Ta = 25°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 Ω) Characteristics Quiet output maximum dynamic VOL Quiet output minimum dynamic VOL Quiet output minimum dynamic VOH Note: Test Condition Symbol VOLP VOLV VOHV VCC (V) Typ. VIH = 1.8 V, VIL = 0 V (Note) 1.8 0.35 VIH = 2.5 V, VIL = 0 V (Note) 2.5 0.7 VIH = 3.3 V, VIL = 0 V (Note) 3.3 0.9 VIH = 1.8 V, VIL = 0 V (Note) 1.8 −0.35 VIH = 2.5 V, VIL = 0 V (Note) 2.5 −0.7 VIH = 3.3 V, VIL = 0 V (Note) 3.3 −0.9 VIH = 1.8 V, VIL = 0 V (Note) 1.8 1.3 VIH = 2.5 V, VIL = 0 V (Note) 2.5 1.7 VIH = 3.3 V, VIL = 0 V (Note) 3.3 2.0 Unit V V V Parameter guaranteed by design. Capacitive Characteristics (Ta = 25°C) Characteristics Input capacitance Output capacitance Power dissipation capacitance Note: Symbol Test Condition CIN ⎯ COUT ⎯ CPD Typ. Unit 1.8, 2.5, 3.3 6 pF 1.8, 2.5, 3.3 7 pF 1.8, 2.5, 3.3 20 pF VCC (V) fIN = 10 MHz (Note) CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/18 (per bit) 9 2007-10-19 TC74VCX16835FT AC Test Circuit 6.0 V or VCC × 2 Open GND RL Switch Switch tpLH, tpHL Open RL Measure CL Output Parameter tpLZ, tpZL CL = 0, 30, 50 pF RL = 500 Ω 6.0 V VCC × 2 tpHZ, tpZH @VCC = 3.3 ± 0.3 V @VCC = 2.5 ± 0.2 V @VCC = 1.8 V GND Figure 1 AC Waveform tr 2.0 ns tf 2.0 ns 90% VM Input (An) VIH 10% GND VOH Output (Yn) VM VOL tpHL tpLH Figure 2 tpLH, tpHL tr 2.0 ns Input (CK) 10% tf 2.0 ns VIH 90% VM GND tw (H) tw (L) VIH Input (An) VM ts (H) th (H) ts (L) th (L) GND VOH Output (Yn) VM tpHL tpLH VOL Figure 3 tpLH, tpHL, tw, ts, th 10 2007-10-19 TC74VCX16835FT tf 2.0 ns Input (LE) VM VIH 90% VM 10% tr 2.0 ns Input (An) tr 2.0 ns VM GND tf 2.0 ns tw (H) VIH 90% 10% VM VM GND ts (H) th (H) ts (L) th (L) VOH Output (Yn) VM VM tpLH tpHL tpHL tpLH VOL Figure 4 tpLH, tpHL, tw, ts, th tr 2.0 ns tf 2.0 ns 90% VM Output Enable Control ( OE ) VIH 10% tpLZ GND tpZL 3.0 V or VCC Output (Yn) Low to Off to Low VM tpHZ VX VOH VY Output (Yn) High to Off to High VOL tpZH VM GND Outputs enabled Outputs enabled Outputs disabled Figure 5 tpLZ, tpHZ, tpZL, tpZH Symbol VCC 3.3 ± 0.3 V 2.5 ± 0.2 V 1.8 V VIH 2.7 V VCC VCC VM 1.5 V VCC/2 VCC/2 VX VOL + 0.3 V VOL + 0.15 V VOL + 0.15 V VY VOH − 0.3 V VOH − 0.15 V VOH − 0.15 V 11 2007-10-19 TC74VCX16835FT IBIS Characteristics (typ.) 0 PC-100 requirement PC-100 requirement VCX16835 (VCC = 3.15 V) VCX16835 (VCC = 3.45 V) High level output current IOH (mA) −50 −100 −150 −200 −250 0 0.5 1.0 1.5 2.0 High level output voltage VOH Figure 6 250 2.5 3.0 (V) I/V Characteristics-Pullup PC-100 requirement PC-100 requirement VCX16835 (VCC = 3.15 V) VCX16835 (VCC = 3.45 V) Low level output current IOL (mA) 200 150 100 50 0 0 0.5 1.0 1.5 2.0 Low level output voltage Figure 7 2.5 3.0 3.5 4.0 VOL (V) I/V Characteristics-Pulldown 12 2007-10-19 TC74VCX16835FT Package Dimensions Weight: 0.25 g (typ.) 13 2007-10-19 TC74VCX16835FT RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 14 2007-10-19