www.fairchildsemi.com KA2S0965/KA2S09655 Fairchild Power Switch(SPS) Features Description • • • • • • • • • The SPS product family is specially designed for an offline SMPS with minimal external components. The SPS consist of high voltage power SenseFET and current mode PWM Controller IC. control IC features a trimmed oscillator, under voltage lock-out, leading edge blanking, optimized gate turnon/turn-off driver, thermal shut down protection, over voltage protection, temperature compensated precision current sources for loop compensation and fault protection circuit. Compared to discrete MOSFET and controller or RCC switching converter solution, a SPS can reduce total component count, design size, weight and at the same time increase &efficiency, productivity, and system reliability. It has a basic platform well suited for cost-effective Monitor power supply. Wide operatimg frequency range up to (150kHz) Pulse by pulse over current limiting Over load protection Over voltage protecton (Min. 23V) Internal thermal shutdown function Under voltage lockout Internal high voltage sense FET External sync terminal Latch up Mode TO-3P-5L 1 1. DRAIN 2. GND 3. Vcc 4. FB 5. Sync Internal Block Diagram #3 VCC 32V 5V Vref Internal bias Good logic − #5 Sync OSC + 5V S 6.4V R − #4 FB 2µA 1mA 2.5R 1R 9V L.E.B 0.1V − + 25V − Q + + 7.5V #1 DRAIN SFET S Thermal S/D R #2 GND Q Power on reset OVER VOLTAGE S/D Rev. .5.0 ©2000 Fairchild Semiconductor International KA2S0965/KA2S09655 Absolute Maximum Ratings Characteristic Symbol Value Unit VDSS 650 V VDGR 650 V VGS ±30 V IDM 36.0 ADC EAS 950 mJ Continuous drain current (TC=25°C) ID 9.0 ADC Continuous drain current (TC=100°C) ID 5.8 ADC Supply voltage VCC 30 V Analog input voltage range VFB −0.3 to VSD V PD 170 W Derating 1.33 W/°C Operating temperature TOPR −25 to +85 °C Storage temperature TSTG −55 to +150 °C Drain-source (GND) voltage (1) Drain-Gate voltage (RGS=1MΩ) Gate-source (GND) voltage Drain current pulsed (2) Single pulsed avalanche energy Total power dissipation (3) Notes: 1.Tj=25°C to 150°C 2.Repetitive rating: Pulse width limited by maximum junction temperature 3.L=20mH, VDD=50V, RG=27Ω, starting Tj=25 °C 2 KA2S0965/KA2S09655 Electrical Characteristics (SFET part) (Ta = 25°C unless otherwise specified) Characteristic Symbol Drain-source breakdown voltage Zero gate voltage drain current Static drain-source on resistance (note) Forward transconductance Min. Typ. Max. Unit VGS=0V, ID=50µA 650 − − V VDS=Max., Rating, VGS=0V − − 50 µA VDS=0.8Max., Rating, VGS=0V, TC=125°C − − 200 µA RDS(ON) VGS=10V, ID=4.5A − 0.96 1.2 Ω gfs VDS=50V, ID=4.5A 5.0 − − S − 1750 − − 190 − − 78 − − 20 50 − 23 55 − 85 180 − 30 70 − 74 95 − 12 − − 35.4 − BVDSS IDSS (note) Input capacitance Ciss Output capacitance Coss Reverse transfer capacitance Crss Turn on delay time td(on) Rise time Turn off delay time Test condition tr td(off) Fall time tf Total gate charge (gate-source+gate-drain) Qg Gate-source charge Qgs Gate-drain (Miller) charge Qgd VGS=0V, VDS=25V, f=1MHz VDD=0.5BVDSS, ID=9.0A (MOSFET switching time are essentially independent of operating temperature) VGS=10V, ID=9.0A, VDS=0.5BVDSS (MOSFET switching time are essentially independent of operating temperature) pF nS nC Note: Pulse test: Pulse width < 300µS, duty cycle < 2% 1 S = ---R 3 KA2S0965/KA2S09655 Electrical Charcteristics (CONTROL part) (Ta = 25°C unless otherwise specified) Characteristic Symbol Test condition Min. Typ. Max. Unit 4.80 5.00 5.20 V −25°C≤Ta≤+85°C − 0.3 0.6 mV/°C REFERENCE SECTION Output voltage (1) Temperature Stability Vref (1)(2) Vref/∆T Ta=25°C OSCILLATOR SECTION Initial accuracy FOSC Ta=25°C 18 20 22 kHz Frequency change with temperature (2) ∆F/∆T −25°C≤Ta≤+85°C − ±5 ±10 % VSYTH Vfb=5V 6.0 6.4 6.8 V 92 95 98 % Ta=25°C, Vfb=GND 0.8 1 1.2 mA Ta=25°C, 5V≤Vfb≤VSD 1.4 1.8 2.2 µA KA2S0965 5.28 6.00 6.72 KA2S09655 4.40 5.00 5.60 14 15 16 V 9 10 11 V VCC=14V 0.1 0.3 0.55 mA Ta=25°C 6 12 18 mA ICC=20mA 30 32.5 35 V (3) Sync threshold voltage PWM SECTION − Dmax Maximum duty cycle FEEDBACK SECTION Feedback source current IFB Shutdown delay current Idelay OVER CURRENT PROTECTION SECTION Over current protection IL(max) A UVLO SECTION Start threshold voltage Vth(H) Minimum operating voltage Vth(L) − After turn on TOTAL STANDBY CURRENT SECTION IST Start current IOPR Operating supply current (control part only) VZ VCC zener voltage SHUTDOWN SECTION Shutdown Feedback voltage Thermal shutdown temperature (Tj) (1) VSD − 6.9 7.5 8.1 V TSD − 140 160 − °C SOFT START SECTION Soft start current ISS Sync & S/S=GND 0.8 − − mA Soft start voltage VSS VFB=2V 4.7 5.0 5.3 V NOTE: 1. These parameters, although guaranteed, are not 100% tested in production 2. These parameters, although guaranteed, are tested in EDS(water test) process 3.The amplitude of the sync. pulse is recommended to be between 2V and 3V for stable sync. function. 4 KA2S0965/KA2S09655 Typical Performance Characteristics (These characteristic graphs are normalized at Ta = 25°C) Fig.2 Feedback Source Current Fig.1 Operating Frequency 1.2 1.15 1.1 1.05 Fosc 1 0.95 0.9 0.85 0.8 -25 0 25 50 75 100 125 150 1.2 1.15 1.1 1.05 Ifb 1 IFB 0.95 0.9 0.85 0.8 -25 0 25 Temperature [°C] Figure 1. Operating Frequency Fig.3 Operating Current 1.2 1.15 1.1 1.05 lIop OPR 1 0.95 0.9 0.85 0.8 -25 100 125 150 Fig.4 Max Inductor Current 1.1 1.05 IL(MAX) Ipeak 1 0.95 0.9 0.85 0 25 50 75 100 125 150 0.8 -25 0 25 50 75 100 125 150 Temperature [°C] Figure 3. Operating Current Figure 4. Max. Inductor Current Fig.5 Start up Current Fig.6 Start Threshold Voltage 1.15 1.1 1.3 1.05 1.1 IIstart ST V th(H) 1 Vstart 0.9 0.95 0.7 0.5 -25 75 Figure 2. Feedback Source Current Temperature [°C] 1.5 50 Temperature [°C] 0.9 0 25 50 75 100 125 150 Temperature [°C] Figure 5. Start up Current 0.85 -25 0 25 50 75 100 125 150 Temperature [°C] Figure 6. Start Threshold Voltage 5 KA2S0965/KA2S09655 Typical Performance Characteristics (Continued) (These characteristic graphs are normalized at Ta = 25°C) Fig.7 Stop Threshold Voltage 1.15 Fig.8 Maximum Duty Cycle 1.15 1.1 1.1 1.05 1.05 Vth(L) 1 Vstop Dmax 1 0.95 0.95 0.9 0.9 0.85 -25 0 25 50 75 100 125 150 0.85 -25 0 Temperature [°C] Figure 7. Stop Threshold Voltage 50 75 100 125 150 Figure 8. Maximum Duty Cycle Fig.10 Shutdown Feedback Voltage Fig.9 Vcc Zener Voltage 1.15 1.2 1.15 1.1 1.05 Vz 1 0.95 0.9 0.85 0.8 -25 1.1 1.05 Vsd 1 0.95 0.9 0 25 50 75 100 125 150 0.85 -25 0 Temperature [°C] 50 75 100 125 150 Figure 10. Shutdown Feedback Voltage Fig.11 Shutdown Delay Current 1.2 1.15 1.1 1.05 Idelay 1 0.95 0.9 0.85 0.8 -25 25 Temperature [°C] Figure 9. VCC Zener Voltage Fig.12 Over Voltage Protection 1.15 1.1 1.05 Vovp 1 0.95 0.9 0 25 50 75 100 125 150 Temperature [°C] Figure 11. Shutdown Delay Current 6 25 Temperature [°C] 0.85 -25 0 25 50 75 100 125 150 Temperature [°C] Figure 12. Over Voltage Protection KA2S0965/KA2S09655 Typical Performance Characteristics (Continued) (These characteristic graphs are normalized at Ta = 25°C) Fig.13 Soft Start Voltage Fig.14 Drain Source Turn-on Resistance 1.15 2.5 1.1 2 1.05 1 1.5 0.95 Rdson 1 0.9 0.5 Vss 0.85 -25 0 25 50 75 100 125 Figure13. Soft Start Voltage 150 0 -25 0 25 50 75 100 125 150 Figure 14. Drain Source Turn-on Resistance 7 KA2S0965/KA2S09655 Package Dimensions TO-3P-5L 8 KA2S0965/KA2S09655 Package Dimensions (Continued) TO-3P-5L (Forming) 9 KA2S0965/KA2S09655 Ordering Information Product Number KA2S0965-TU KA2S0965-YDTU KA2S09655-TU KA2S09655-YDTU TU : Non Forming Type YDTU : Forming Type 10 Package TO-3P-5L TO-3P-5L(Forming) TO-3P-5L TO-3P-5L(Forming) Rating Over current protection 650V, 9A 6A 650V, 9A 5A KA2S0965/KA2S09655 11 KA2S0965/KA2S09655 DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR INTERNATIONAL. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 9/7/00 0.0m 001 Stock#DSxxxxxxxx 2000 Fairchild Semiconductor International