PLETRONICS VHD6031035CM

VHD6 Series 3.3V
VCXO CMOS Oscillator
December 2008
• Pletronics’ VHD6 Series is a voltage controlled
crystal oscillator with a CMOS output.
• This model uses fundamental mode crystals
with no multiplication circuits.
• Tape and Reel or tube packaging is available.
•
•
•
•
10 to 108 MHZ
3.2 x 5 mm Ceramic LCC Package
Voltage Control Function on pad 1
Enable/ Disable Function on pad 2
Pletronics Inc. certifies this device is in accordance with the
RoHS 6/6 (2002/95/EC) and WEEE (2002/96/EC) directives.
Pletronics Inc. guarantees the device does not contain the following:
Cadmium, Hexavalent Chromium, Lead, Mercury, PBB’s, PBDE’s
Weight of the Device: 0.09 grams
Moisture Sensitivity Level: 1 As defined in J-STD-020C
Second Level Interconnect code: e4
Absolute Maximum Ratings:
Parameter
Unit
VCC Supply Voltage
-0.5V to +5.5V
Vi
Input Voltage
-0.5V to VCC + 0.5V
Vo
Output Voltage
-0.5V to VCC + 0.5V
Thermal Characteristics
The maximum die or junction temperature is 155oC
The thermal resistance junction to board is 60 to 100oC/Watt depending on the solder pads, ground plane
and construction of the PCB.
Product information is current as of publication date. The product conforms
to specifications per the terms of the Pletronics standard warranty. Production
processing does not necessarily include testing of all parameters.
Copyright © 2008, Pletronics Inc.
VHD6 Series 3.3V
VCXO CMOS Oscillator
December 2008
Part Number:
VHD6031035
E
G
500
100
-16.384M
-XX
Internal code or blank
Nominal Frequency in MHZ
Pullability in ppm (Vcontrol)
050 = _
+ 50 ppm minimum
100 = _
+ 100 ppm minimum
Stability in ppm
000 = APR
250 = _
+ 25 ppm
500 = _
+ 50 ppm
Highest Specified Operating Temperature
A = +40oC F = +65oC L = +90oC
B = +45oC G = +70oC M = +95oC
C = +50oC H = +75oC N = +100oC
P = +105oC
D = +55oC J = +80oC
o
o
E = +60 C K = +85 C
Lowest Specified Operating Temperature
J = -30oC
A = +10oC E = -10oC
F = -15oC
K = -35oC
B = +5oC
o
o
G = -20 C
L = -40oC
C = +0 C
H = -25oC
M = -45oC
D = -5oC
Series (Part Type, Logic & Package)
Part Marking:
PLE VHD6
FF.FFFM
C YMDXX
Legend:
P or PLE
FF.FFFM
YMD
xx
= Pletronics
= Frequency in MHZ
= Date of Manufacture
= Internal factory codes
Specifications such as frequency stability, supply voltage and operating temperature range, etc. are not
identified from the marking. External packaging labels and packing list will correctly identify the ordered
Pletronics part number.
Codes for Date Code YMD
Code
Year
8
2008
Code
Month
Code
Day
Code
Day
Code
Day
9
2009
A
JAN
1
1
D
13
T
25
B
FEB
2
2
E
14
U
26
www.pletronics.com
0
2010
C
MAR
3
3
F
15
V
27
1
2011
D
APR
4
4
G
16
W
28
2
2012
E
MAY
5
5
H
17
X
29
425-776-1880
F
JUN
6
6
J
18
Y
30
3
2013
G
JUL
7
7
K
19
Z
31
4
2014
H
AUG
J
SEP
K
OCT
L
NOV
M
DEC
8
8
L
20
9
9
M
21
A
10
N
22
B
11
P
23
C
12
R
24
2
VHD6 Series 3.3V
VCXO CMOS Oscillator
December 2008
Electrical Specification for 3.30V _
+5% over the specified temperature range
Item
Min
Typ
Max
Unit
Frequency Range
10
-
108
MHZ
Frequency Accuracy 1
_
+25
-
-
ppm
Not specified if APR is specified
Pullability 1
_ 90
+
-
+
_ 125
ppm
For Vcontrol 1.65 V _
+1.5 V.
Not specified if APR is specified
Defined by the part number
Pullability (APR) 1
_
+50
-
-
ppm
Absolute Pull Range, includes the effect of
temperature stability
Defined by the part number
Output Waveform
Condition
CMOS
Output High Level
90
-
-
%
of VCC for IOH= +7 mA
Output Low Level
-
-
10
%
of VCC for IOL = -7 mA
Output TRISE and TFALL
-
3.0
6.0
nS
10% to 90% of VCC, CLOAD = 15 pF
Output Symmetry
45
50
55
%
at 50% point of VCC (See load circuit)
Vcontrol Resistance Pin 1
20
25
-
Kohm
Modulation Bandwidth
10
20
-
KHz
-
0.4
0.6
pS
50
-
-
Kohm
V disable
-
-
15
%
of VCC applied to pin 1
V enable
85
-
-
%
of VCC applied to pin 1
-10
-
+10
uA
Pin 1 low, device disabled
-10
-
+10
uA
Enable time
-
-
250
nS
Time for output to reach a logic state
Disable time
-
-
250
nS
Time for output to reach a high Z state
Start up time
-
1.5
10
mS
Time for output to reach specified frequency
Supply Current
-
5.0
8.0
mA
CLOAD = 15 pF
Integrated Jitter
E/D Internal Pull-up
Output leakage
VOUT = VCC
VOUT = 0V
Operating Temperature
-45
+105
o
Storage Temperature Range
-55
+125
o
C
Vcontrol = 1.65V +
_ 1.65V, -3dB
12 KHz to 20 MHZ
to VCC
Defined by part number
C
Specifications with Pad 2 E/D open circuit
1
For all supply voltages, load changes, aging for 1 year, shock, vibration and temperatures.
www.pletronics.com
425-776-1880
3
VHD6 Series 3.3V
VCXO CMOS Oscillator
December 2008
Load Circuit and Test Waveform
Symmetry
Vhigh
90% * Vcc
50% * Vcc
10% * Vcc
Vlow
Ground
Trise
Tfall
Reliability: Environmental Compliance
Parameter
Condition
Mechanical Shock
MIL-STD-883 Method 2002, Condition B
Vibration
MIL-STD-883 Method 2007, Condition A
Solderability
MIL-STD-883 Method 2003
Thermal Shock
MIL-STD-883 Method 1011, Condition A
ESD Rating
Model
Minimum Voltage
Conditions
Human Body Model
1500
MIL-STD-883 Method 3115
Charged Device Model
1000
JESD 22-C101
Package Labeling
Label is 1" x 2.6" (25.4mm x 66.7mm)
Font is Courier New
Bar code is 39-Full ASCII
(example actual PN will appear)
www.pletronics.com
Label is 1" x 2.6" (25.4mm x 66.7mm)
Font is Arial
425-776-1880
4
VHD6 Series 3.3V
VCXO CMOS Oscillator
December 2008
Mechanical:
Inches
6
2
5
3
1
1
4
A
0.197 +
_ 0.006
5.00 +
_ 0.15
B
0.125 +
_ 0.006
3.20 +
_ 0.15
C
0.053 max
1.35 max
D1
0.050
1.27
E1
0.050
1.27
F1
0.004
0.10
G1
0.039
1.00
H1
0.025
0.63
1
0.020
0.50
J1
0.004R
0.10R
K1
0.008R
0.20R
I
Contacts:
Gold 11.8 µinches 0.3 µm minimum over
Nickel 50 to 350 µinches 1.27 to 8.89 µm
Pad
Function
1
Typical dimensions
Not to Scale
mm
Note
1
Vcontrol Input
2
Output
Enable/ Disable
3
Ground (GND)
4
Output
5
N.C.
No Internal connection, pad may be connected to ground or VCC
6
Supply Voltage
(VCC)
Recommend connecting appropriate power supply bypass capacitors as close as
possible.
When this pad is not connected, the oscillator shall operate
When this pad is logic low, the output will be inhibited (high impedance state)
Recommend connecting this pad to Vcc if the oscillator is to be always on
Layout and application information
For Optimum Jitter Performance, Pletronics recommends:
•
a ground plane under the device
•
no large transient signals (both current and voltage) should be routed under the device do not layout
near a large magnetic field such as a high frequency switching power supply
•
do not place near piezoelectric buzzers or mechanical fans.
www.pletronics.com
425-776-1880
5
VHD6 Series 3.3V
VCXO CMOS Oscillator
December 2008
Reflow Cycle (typical for lead free processing)
260°C Maximum
10 Seconds Maximum
Temperature (°C)
250
215°C±10°C
200
175°C±10°C
150
100
Approximately 50 Seconds
120 to 160 Seconds
Allowed rate of temperature change
Maximum 4°C per second
The part may be reflowed 2 times without degradation.
Tape and Reel: available for quantities of 250 to 1000 per reel
Constant Dimensions Table 1
Tape
Size
D0
8mm
D1
Min
E1
P0
1.0
S1
Min
T
Max
0.6
0.6
T1
Max
2.0
+0.05
_
12mm
1.5
1.5
1.75
4.0
16mm
+0.1
-0.0
1.5
_
+0.1
_0.1
+
24mm
P2
0.1
2.0
_
+0.1
1.5
Variable Dimensions Table 2
Tape
Size
B1
Max
E2 Min
F
P1
T2
Max
W
Max
Ao, Bo &
Ko
16 mm
12.1
14.25
7.5 _
+0.1
8.0 +
_0.1
8.0
16.3
Note 1
Note 1: Embossed cavity to conform to EIA-481-B
Dimensions in mm
Not to scale
REEL DIMENSIONS
A
B
inches
7.0
10.0
13.0
mm
177.8
254.0
330.2
inches
2.50
4.00
3.75
mm
63.5
101.6
95.3
Tape
Width
16.4
+2.0
-0.0
16.0
C
mm
D
mm
13.0 +0.5 / -0.2
16.4
+2.0
-0.0
16.4
+2.0
-0.0
Reel dimensions may vary from the above
www.pletronics.com
425-776-1880
6
VHD6 Series 3.3V
VCXO CMOS Oscillator
December 2008
IMPORTANT NOTICE
Pletronics Incorporated (PLE) reserves the right to make corrections, improvements, modifications and
other changes to this product at anytime. PLE reserves the right to discontinue any product or service
without notice. Customers are responsible for obtaining the latest relevant information before placing orders
and should verify that such information is current and complete. All products are sold subject to PLE’s
terms and conditions of sale supplied at the time of order acknowledgment.
PLE warrants performance of this product to the specifications applicable at the time of sale in accordance
with PLE’s limited warranty. Testing and other quality control techniques are used to the extent PLE deems
necessary to support this warranty. Except where mandated by specific contractual documents, testing of
all parameters of each product is not necessarily performed.
PLE assumes no liability for application assistance or customer product design. Customers are responsible
for their products and applications using PLE components. To minimize the risks associated with the
customer products and applications, customers should provide adequate design and operating safeguards.
PLE products are not designed, intended, authorized or warranted to be suitable for use in life support
applications, devices or systems or other critical applications that may involve potential risks of death,
personal injury or severe property or environmental damage. Inclusion of PLE products in such applications
is understood to be fully at the risk of the customer. Use of PLE products in such applications requires the
written approval of an appropriate PLE officer. Questions concerning potential risk applications should be
directed to PLE.
PLE does not warrant or represent that any license, either express or implied, is granted under any PLE
patent right, copyright, artwork or other intellectual property right relating to any combination, machine or
process which PLE product or services are used. Information published by PLE regarding third-party
products or services does not constitute a license from PLE to use such products or services or a warranty
or endorsement thereof. Use of such information may require a license from a third party under the patents
or other intellectual property of the third party, or a license from PLE under the patents or other intellectual
property of PLE.
Reproduction of information in PLE data sheets or web site is permissible only if the reproduction is without
alteration and is accompanied by associated warranties, conditions, limitations and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. PLE is not responsible or
liable for such altered documents.
Resale of PLE products or services with statements different from or beyond the parameters stated by PLE
for that product or service voids all express and implied warranties for the associated PLE product or
service and is an unfair or deceptive business practice. PLE is not responsible for any such statements.
Contacting Pletronics Inc.
Pletronics Inc.
19013 36th Ave. West
Lynnwood, WA 98036-5761 USA
Tel: 425-776-1880
Fax: 425-776-2760
E-mail: [email protected]
URL: www.pletronics.com
Copyright © 2008, Pletronics Inc.
www.pletronics.com
425-776-1880
7