KA2003-BE51A Printheads For Mobile, FET-POS, Debit Card, PDA, ECR 2.7V Print Voltage (B Series) KA2003-BE51A Not only hand-held printers, but card payment terminals (EFT-POS) and compact label printers require less than 8.5V of supply voltage. ROHM’s B Series of thermal printheads, developed using cutting-edge LSI technology, can operate on a single lithium ion battery and contribute to end-product miniaturization. zApplications Mobile printers EFT-POS printers Hand-held printers Debit printers zFeatures 1) The B series brings reduced height of protective resin for IC and enlarged paper pathway for thermal papers. Thanks to ROHM’s latest LSI high integrated mounting technology and it’s ultra slim driver IC. 2) The B series accede the great world class low energy consumption characteristics of GP series. zDimensions (Unit : mm) 80 72 (Effective Print Width) Exposed Conductor Side Insert Direction Connector Rev.A 1/4 KA2003-BE51A Printheads zEquivalent circuit DOT#576 DOT #1 VH #513～ #576 L-GND #449～ #385～ #512 #448 #321～ #384 #257～ #193～ #129～ #65～ #320 #256 #192 #128 #1～ #64 P-GND STB5 STB4 STB3 STB2 STB1 /AEO2 /AEO1 LATCH REGISTER /LAT DI ＬＡＴＣＨ ＲＥＧＩＳＴＥＲ SHIFT REGISTER CLK DO VDD NC ＴＨＥＲＭＩＳＴＯＲ 30kΩ B：3950K TM TM CONNECTOR zPin assignments Circuit No. Circuit 1 VH 15 P-GND 2 VH 16 P-GND 3 VH 17 P-GND 4 DO 18 L-GND 5 /LAT 19 /AEO1 6 CLK 20 /AEO2 7 VDD 21 STB4 8 STB1 22 STB5 9 STB2 23 N.C. 10 STB3 24 N.C. 11 TM 25 DI 12 TM 26 VH 13 P-GND 27 VH 14 P-GND 28 VH No. Rev.A 2/4 KA2003-BE51A Printheads zTiming chart tw CLK CLK (CLOCK) t hold DI t setup DI DI(DATA IN) "High":BLACK "LOW" :WHITE td DO DO (DATA OUT) "High":BLACK "LOW" :WHITE Min.10µs∗ t setup LAT t hold LAT /LAT (LATCH) "High": HOLD "LOW" : THROUGH tw LAT t setup STB STB (STROBE) /AEO (AREA ENABLE OUT) t do t do DRIVER OUT *If delay time for Driver Out can not be secured enough, there is a possibility that VH would fluctuate greatly. Please design the circuit so that VH does not exceed peak voltage (Vp). zCharacteristics Symbol Typical Unit Effective printing width − 72 mm Dot pitch − 0.125 mm Total dot number − 576 dots Rave 176 Ω Parameter Average resistance value Applied voltage VH 7.2 V Applied power PO 0.24 W/dot Print cycle SLT 1.25 ms Pulse width TON 0.55 ms Maximum number of dots energized simultaneously − 64 dots Maximum clock frequency − 8 MHz Maximum roller diameter − φ14 mm Running life / pulse life − 50/1×108 km/pulses Operating temperature − 5 to 45 °C Rev.A 3/4 KA2003-BE51A Printheads zElectrical characteristic curves 0.8 1.8 0.8 Paper : KF50-HDA (OJI) 0.7 1.4 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3 4 5 SCANNING LINE TIME (ms/line) 0.6 ENERGY (mJ/dot) OPTICAL DENSITY 0.6 ENERGY (mJ/dot) SLT : 2.50ms/line 1.6 0.7 1.2 1.0 0.8 0.6 0.4 0.3 0.4 0.2 0.2 0.1 0.0 0.00 0.05 0.10 0.15 0.20 0.25 0.30 ENERGY (mJ/dot) Fig.1 Adaptive speed chart 0.5 Fig.2 Representative density curve 0 0 1 2 3 4 5 SCANNING LINE TIME (ms/line) Fig.3 Maximum energy curve 180 160 RESISTANCE : (kΩ) 140 120 100 80 60 40 20 0 −20 −10 0 10 20 30 40 50 60 70 TEMPERATURE : (°C) Fig.4 Thermistor curve Rev.A 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0