RPMS2401-H19 series Photo Link Module Ultra-compact Surface Mount Remote Control Photoreceiver Module RPMS2401-H19 zOutline ROHM’s RPMS2401-H19 photoreceiver, utilizing original miniaturization technology, features the smallest∗ mounting area in the world. In addition, the S/N ratio in broad daylight is significantly improved due to ROHM’s unique optical technology. zDimensions (Unit : mm) MOUNTING CENTER 1.04 2.85 1.15 1.2 3.02 1.54 1.82 4.33 2.49 zFeatures 2 1) Smallest mounting area in the world (9mm ) 2) Resistant to sunlight noise 3) Low power consumption: 950µA (in standby mode) 2.04 2.45 zApplications All types of portable devices, including digital still and video cameras, car navigation equipment, laptops, and gaming consoles zAbsolute maximum ratings (Ta = 25°C) Symbol Limits Unit Supply Voltage Vcc 6.3 V Output Current Io 2.0 mA Storage temperature Tstg −40 to +100 °C Operating temperature Topr −40 to +85 °C Parameter Conditions No condensation ∗ Jan.07 ROHM study 1/2 RPMS2401-H19 series Photo Link Module zElectrical, Optical characteristics (Ta = 25°C) Recommended operating conditions Parameter Symbol Min. Typ. Max. Unit Supply voltage Vcc 4.5 5.0 5.5 V Characteristics Parameter Consumption Current Symbol Min. Typ. Max. Unit lcc − 0.95 1.5 mA Conditions No outside light, No signal input L 5 8 − m ∗1 Outer light condition Ee 10 (Ix) High Level Output Voltage VH 4.5 − − V ∗1 Low Level Output Voltage VL − − 0.5 V ∗1 I sink 200µA ON Pulse Width TON 400 600 800 µs ∗1 Outer light condition Ee 10 (Ix) OFF Pulse Width TOFF 400 600 800 µs ∗1 Outer light condition Ee 10 (Ix) Center frequency fo − 40.0 − kHz Horizontal half angle θ1/2 − 34 − deg ∗2 Vertical half angle θ1/2 − 32 − deg ∗2 Effective Distance ∗1 600/600µs burst wave is transmitted by standard transmitter. However, it must be measured after the initial transmission pulse is 10 pulse. ∗2 It is an angle when the linear arrival distance become half. 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0