NE3002-WA30A Printheads Near edge thermal printhead (with thermal historical control) NE3002-WA30A NE-WA30 series are the thermal printheads developed for high-speed / high-resolution printing for the market of bar-code printer & scale-printer, based on “step-free” structure. These printheads realize ultra-highspeed printing with long life & high reliability. zApplications Bar code printer Label printer Packaging printer ATM Ticket printer zFeatures 1) High dot reproducibility with step-free structure. 2) About 8° head inclination by near-edge structure, applicable to the large-size platen. Resin type thermal-transfer ink-ribbon can be used. 3) High-hardness protect cote type “W-coat” is employed with 150km abrasion life-time. 4) Even without history-control, high-speed printing more than 300mm / s can be achieved at 300dpi with clear print image. With history-control, 500mm / s printing is also possible at 300dpi. zExternal dimensions (Unit : mm) 7.104±0.3 66±0.5 40±0.3 6±0.5 DOT No.1 SECTION A 54.208 (13) 20±0.3 φ 3 H10 Length 4 MAX.4.5 #20 #2 #4 MAX.11 7.3±0.3 Print Dir ection 0369UB 34.0±0.5 MAX.51 (5.896) 24.455±0.3 DOT No.640 φ 3 H10 Effective Depth 3 #1 M3 Effective Depth 3 CONNECTOR A #1 CONNECTOR B #19 TYPE OF PRINTHEAD 1/3 NE3002-WA30A Printheads zEquivalent circuit DOT #640 VH (COM) DOT #1 220µF 35V GND 0.1µF 50V VDD (+5) / STB2 / STB1 BEO / RESET LATCH REGISTER CLK (CP) DI / LOAD START TO EACH IC INC SEL2 SEL1 TM THERMISTOR 30kΩ B: 3950 TM DI, STB DIVISION DOT No. CORRESPONDENCE DI No. DOT No. / STB No. DOT No. DI 640 to 1 / STB2 640 to 385 / STB1 384 to 1 zPin assignments CONNECTOR A CONNECTOR B Circuit No. Circuit No. Circuit No. Circuit 1 VDD 2 BEO 1 VH (COM) 2 VH (COM) 3 GND 4 DI 3 GND 4 GND 5 GND 6 CLK(CP) 7 /LOAD 8 START No. 9 INC 10 N.C. 11 SEL2 12 SEL1 13 /RESET 14 / STB 2 15 / STB 1 16 TM 17 TM 18 SENS1 19 SENS2 20 SENS3 2/3 NE3002-WA30A Printheads zCharacteristics Parameter Symbol Typical Unit − 54.2 mm Dot pitch − 0.0847 mm Total dot number − 640 dots Rave 850 Ω Effective printing width Average resistance value Applied voltage VH 24 V Applied power PO 0.59 W/dot SLT 0.28 ms Maximum number of dots energized simultaneously − 640 dots Maximum clock frequency − 8 MHz Maximum roller diameter − φ50 mm Running life / pulse life − 150/(1×108) km/pulses Operating temperature − 5 to 45 °C Print cycle 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1