Data Sheet AC80V to AC138V input, 18W output Isolated AC/DC converter BP5717 Absolute Maximum Ratings Dimensions (Unit : mm) (Ta=25°C) Unit V Apk V V mA mA mA W kV °C °C °C Conditions 113V to195VDC (about 80 to 138VAC) 1sec (between primary and secondary) (Ambient temperature + the module self-heating)≤Tcmax Typ. 12.0 − Max. 12.6 1500 Unit V mA Vr VI Vp η − − − 82 2 5 55 87 200 200 500 − mV mV mVpp % Conditions Io=1500mA ∗1 Vi=113V to 195VDC Io=1500mA Io=50 to 1500mA Io=1500mA ∗2 Io=1500mA ∗1: Maximum output current must be reduced by ambient temperature. ∗2: An output ripple voltage sometimes changes in capacitor to use, the measurement environment. Especially right attention has to be paid to aluminum electrolytic capacitor,because ESR changes greatly at the time of the low temperature and output voltages increase. Sample Application Circuit C1 C2 C3 C5 RTH D2 C7 R3 R4 D1 + ZNR D4 R2 + F1 FL1 12V 1.5A C8 D3 C4 R1 + C6 T1 12 10 8 7 6 3 2 1 Pin No. 1 Name Function PC Secondary-Side Photocoupler Current Supply Pin 2 Vo Secondary Output Voltage Control Pin. Connect the output smoothing capacitor between GND. 3 GND GND Pin for Secondary Output 6 ZCD Zero-Current Adjustment Pin 7 Vcc Internal Power Supply Pin 8 Vin(-) 10 VH Startup Pin VD Drain Pin for Internal FET. Connect to the primary windings of the external transformer. 12 External Component Settings 0.1 to 0.22µF/AC250V 47µF / 250V 10µF / 50V low impedance 2200pF / 1kV Use if necessary 1000µF / 35V×2 low impedance, Rated ripple current 5.5Arms. 2200pF/AC250V FRD 200V/0.5A 600V/1A 60V/20A 400V/1A 47kΩ±1% 0.125W 200kW±5% 3Ω Rated at 300V or higher 69.2Ω (68kW + 1.2kW) ±1% 0.125W 910Ω ±1% 0.125W Be sure to use this for safety Be sure to use this for safety Use if necessary www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 12 0.25±0.05 7.05MAX. 2.25MAX. 1/1 Operation Range -10 0 10 20 30 40 50 60 70 80 90 Ambient Temperature Ta(°C) Conversion Efficiency (Vin=141V, Ta=25°C) 100 80 60 40 20 0 0 250 500 750 1000 1250 1500 Output Current Io (mA) Load Regulation Primary Input (Negative) Pin BP5717 C1,C2: EMI Capacitor for AC Line C3: Input smoothing capacitor C4: Vcc smoothing capacitor C5: Noise reduction capacitor C6: Quasi-resonance capacitor C7: Output smoothing capacitor C8: Noise reduction capacitor D1: Rectifier diode D2: Rectifier diode D3: Rectifier diode D4: Diode bridge R1: Zero-Current Adjustment Resistor R2: Snubber Resistor R3: Output voltage setting resistor R4: PC Current-Limiting Resistor T1: Switching transformer F1: Fuse FL1: EMI Filter for AC Line ZNR: Varistor RTH: Thermistor Output Power (W) Min. 11.4 0 Conversion Efficiency η(%) Symbol Vo Io Be sure to use fuse for safety. 6 7 8 10 0.5±0.1 1.3±0.2 P=2.54±0.2 2.54X11=27.94TYP. 20 18 16 14 12 10 8 6 4 2 0 -30 -20 (Vin=141V, Ta=25°C) Output Voltage Vo(V) Line regulation Load regulation Output ripple voltage Power conversion efficiency 1 2 3 Derating Curve (Unless otherwise noted, Vi=141V, rated load Ta=25°C) Parameter Output voltage Output current MARKING SIDE 3.25MAX Electrical Characteristics <12V output> 9.3MAX MARKING SIDE 24.3MAX 37.4MAX 4.0±1.0 Symbol Limits VD 480 ID 1 VH 400 VCC 30 Isozcd −2.0 6-pin input current Isizcd +3.0 Ipc 10 1-pin input current Po 18 Maximum power VI 2.5 Withstanding voltage 105 Allowable maximum surface temperature Tcmax −25 to +80 Operating temperature range Topr Tstg −30 to +105 Storage temperature range 16 14 12 10 8 6 4 2 0 0 500 1000 1500 2000 2500 Output Current Io (mA) Line Regulation (lo=1500mA, Ta=25°C) 12.6 Output voltage (V) Parameter 12-pin input voltage 12-pin input current 10-pin input voltage 7-pin input voltage 12.4 12.2 12.0 11.8 11.6 11.4 100 120 140 160 180 200 Input voltage (V) 2011.10 - Rev. A Notice Notes Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A