High-performance Video Driver Series Y/C MIX Circuit built-in Video Driver No.09065EAT02 BA7664AFV ●Description BA7664AFV is a 75Ω video driver, packaged in SSOP-B8, incorporating a 6dB amplifier, Y/C MIX circuit, sag compensation, and Mute function. This driver can drive two 75Ω loads. While the composite Y signal input is sync-tip-clamp, the chroma input has an internal termination at 20kΩ. The device also incorporates a power save circuit by activated when the output is under 0.2V. ●Features 1) A low consumption electric power movement 2) Built-in output mute circuit 3) Built-in power save circuit 4) Built-in output protection circuit 5) Low output coupling capacitor value can be used due to a built-in sag compensation circuit 6) The driver can have two loads (each channel) 7) Built-in Y/C MIX circuit ●Applications DVD, DVC, DSC, STB, and visual instruments. ●Absolute maximum ratings (Ta=25°C) Parameter Symbol Limits Unit Power Supply Voltage Power Dissipation Operating Temperature Range Storage Temperature Range Vcc Pd Topr Tstg 8 350 *1 -25～+75 -55～+125 V mV °C °C *1 At the time of glass epoxy (FR-4) PCB mounting (70mm×70mm×1.6mm). Reduce by 3.5 mW/C over 25C ●Operating range (Ta=25°C) Parameter Supply voltage www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Symbol Min Typ Max Unit Vcc 4.5 5.0 5.5 V 1/4 2009.04 - Rev.A Technical Note BA7664AFV ●Electrical characteristics Electrical characteristics (unless otherwise specified, Vcc=5V, Ta=25°C) Parameter Symbol Min Typ Max Unit Circuit Current ICC 6.1 12.2 18.3 mA Maximum Output Level Vom 2.6 3.0 VP-P Voltage Gain -1.0 -0.2 0.6 dB GV Frequency Characteristics GF -1.5 -0.5 0.5 dB MUTE Attenuation MT -60 dB Mute Threshold “H” VTHH 2.2 VCC V Mute Threshold “L” VTHL 0 0.7 V Input Impedance ZIN 16 20 24 kΩ Supply Current in Mute 1.3 2.6 mA IMUTE Guaranteed design parameters Conditions No-signal f=1kHz,THD=1% V02 f=4.43MHz,1Vpp/V01 f=7MHz/1MHz,1VP-P/V01 f=4.43MHz,1VP-P/V01 Chroma input terminal MUTEA“H” (unless otherwise specified, Vcc=5V, Ta=25°C) Parameter Differential Gain Differential Phase Symbol Min Typ Max Unit Conditions DG DP - 1.0 0.5 2.0 2.0 % DEG VIN=1VP-P Standard staircase signal VIN=1VP-P Standard staircase signal ●Block diagram / Application circuit Place decoupling and bypass capacitors near the IC Put decoupling capacitors near the IC. MUTE 1 8 Open or GND 47uF 0.1uF 75Ω 1uF 1000uF 2 6dB 7 75Ω 3 0.1uF 75Ω 6 20k CHROMA MUTE 4 5 Open or GND When sag compensation function is used. 6dB 75Ω 7 8 100uF 22uF 75Ω 75Ω ※ The application is recommended forcharacteristics use. ※ Make sure to takecircuit into account the tolerance of When usingcomponents, the circuit, make sure to confirm the adequnacy of the characteristics. the external as well as the IC power dissipation limits. Make sure to leave an adequate margin for external components includingstatic and transitional characteristics as well as dispersion of the IC. Fig.1 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 2/4 2009.04 - Rev.A Technical Note BA7664AFV ●Equivalent circuit Pin.No Pin name IN OUT Voltage Equivalent circuit Function Mute control terminal 1 5 MUTEA MUTEB 15k ○ ― Pin1 MUTEA - “H” = mute on Pin5 MUTEB - “H” = only chroma mute on ― 14k Signal input terminal 2 YIN ○ ― 2.0V 3 GND ― ― 0V Sync-tip-clamp input for the composite Y signal. Ground terminal GND Signal input terminal 4 CIN ○ ― 2.0V This pin is a chroma signal input. Input terminal is 20kΩ. 20k Signal output terminal Pin7 is Y/C MIX signal output terminal. Power save mode is active when output is set under 0.2V. Pin6 is a sag compensator input. Pin6 6 7 MIXOUT2 MIXOUT1 ― ○ 0.9V 0.95V Pin7 8 VCC ― ― VCC 5.0V Power supply terminal ●Cautions on use 1. 2. 3. 4. 5. 6. 7. Numbers and data in entries are representative design values and are not guaranteed values of the items. Although ROHM is confident that the example application circuit reflects the best possible recommendations, be sure to verify circuit characteristics for your particular application. Modification of constants for other externally connected circuits may cause variations in both static and transient characteristics for external components as well as this ROHM IC. Allow for sufficient margins when determining circuit constants. Absolute maximum ratings Use of the IC in excess of absolute maximum ratings, such as the applied voltage or operating temperature range (Topr), may result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such damage is suffered. A physical safety measure, such as a fuse, should be implemented when using the IC at times where the absolute maximum ratings may be exceeded. GND potential Ensure a minimum GND pin potential in all operating conditions. Make sure that no pins are at a voltage below the GND at any time, regardless of whether it is a transient signal or not. Thermal design Perform thermal design, in which there are adequate margins, by taking into account the permissible dissipation (Pd) in actual states of use. Short circuit between terminals and erroneous mounting Pay attention to the assembly direction of the ICs. Wrong mounting direction or shorts between terminals, GND, or other components on the circuits, can damage the IC. Operation in strong electromagnetic field Using the ICs in a strong electromagnetic field can cause operation malfunction. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 3/4 2009.04 - Rev.A Technical Note BA7664AFV ●Selection of order type A B 7 6 6 A 4 2 E V F TYPE Package, Foaming specifications BA7664AFV SSOP-B8 <Dimension> <Tape and Reel information> Tape 3.0±0.2 5 1 4 2500pcs E2 (Correct direction: 1pin of product should be at the upper left when you hold reel with the left hand, and you pull out the tape with the right hand) 0.15±0.1 0.1 1234 1234 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 1234 （Unit:mm) 1pin 1234 Reel 1234 0.65 1234 0.22±0.1 1234 (0.52) Quantity Direction of feed 1234 1.15±0.1 0.1 6.4±0.3 4.4±0.2 0.3Min. 8 Embossed carrier tape Direction of feed ※Orders are available in complete units only. 4/4 2009.04 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A