PBL401 - PBL407 4.0A BRIDGE RECTIFIER NOT RECOMMENDED FOR NEW DESIGN USE GBU4005 - GBU410 Features · · · · · · High Case Dielectric Strength of 1500V Low Forward Voltage Drop, High Current Capability Surge Overload Rating to 150A Peak Ideal for Printed Circuit Board Application Plastic Material - UL Flammability Classification 94V-0 UL Listed Under Recognized Component Index, File Number E95060 A PBL B Dim Min Max A 18.50 19.50 B 15.40 16.40 C 19.00 — D 6.20 6.50 E 4.60 5.60 G 1.50 2.00 - + C H Mechanical Data · · · · · Case: Molded Plastic Terminals: Plated Leads, Solderable per MIL-STD-202, Method 208 Polarity: Symbols Marked on Case Approx. Weight: 5.6 grams Marking: Type Number H G D 1.30 Typical All Dimensions in mm E Maximum Ratings and Electrical Characteristics @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current @ TC= 75°C Symbol PBL 401 PBL 402 PBL 403 PBL 404 PBL 405 PBL 406 PBL 407 Unit VRRM VRWM VR 50 100 200 400 600 800 1000 V VR(RMS) 35 70 140 280 420 560 700 V IO 4.0 A Non-Repetitive Peak Forward Surge Current, 8.3 ms single half-sine-wave superimposed on rated load (JEDEC method) IFSM 150 A Forward Voltage per element VFM 1.1 V IR 10 1.0 µA mA I2t 166 A2s RqJC 19 °C/W Tj, TSTG -65 to +125 °C Peak Reverse Current at Rated DC Blocking Voltage @ IF = 3.0A @TC = 25°C @ TC = 100°C I2t Rating for Fusing (t < 8.3ms) (Note 2) Typical Thermal Resistance, Junction to Case (Note 1) Operating and Storage Temperature Range Notes: 1. Thermal resistance rom junction to case per element mounted on PC board with 13 x 13 x 0.03mm land areas. 2. Non-repetitive for t > 1ms and < 8.3ms. DS21305 Rev. E-3 1 of 2 PBL401-PBL407 20 IF, INSTANTANEOUS FWD CURRENT (A) IO, AVERAGE OUTPUT CURRENT (A) 5 4 3 2 1 Single Phase Half Wave 60 Hz Resistive or Inductive Load 0 20 40 60 80 100 120 140 Tj = 25ºC Pulse Width = 300 ms 2% Duty Cycle 10 1.0 0.1 0.01 0 250 200 150 100 50 8.3ms Single Half Sine-Wave JEDEC Method 0 1 10 100 NUMBER OF CYCLES AT 60 Hz Fig. 3 Max Non-Repetitive Peak Fwd Surge Current DS21305 Rev. E-3 0.4 0.6 0.8 1.0 1.2 1.4 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics IR, INSTANTANEOUS REVERSE CURRENT (mA) IFSM, PEAK FORWARD SURGE CURRENT (A) TC, CASE TEMPERATURE (ºC) Fig. 1 Forward Current Derating Curve 0.2 2 of 2 10 TC = 100°C 1.0 0.1 TA = 25°C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) Fig. 4 Typical Reverse Characteristics, per element PBL401-PBL407