MUR1610CT, MUR1615CT, MUR1620CT, MUR1640CT, MUR1660CT SWITCHMODE Power Rectifiers http://onsemi.com . . . designed for use in switching power supplies, inverters and as free wheeling diodes, these state–of–the–art devices have the following features: • • • • • • • • ULTRAFAST RECTIFIERS 8.0 AMPERES 100–600 VOLTS Ultrafast 35 and 60 Nanosecond Recovery Times 175°C Operating Junction Temperature Popular TO–220 Package Epoxy Meets UL94, VO @ 1/8″ High Temperature Glass Passivated Junction High Voltage Capability to 600 Volts Low Leakage Specified @ 150°C Case Temperature Current Derating @ Both Case and Ambient Temperatures 1 2, 4 3 Mechanical Characteristics: • Case: Epoxy, Molded • Weight: 1.9 grams (approximately) • Finish: All External Surfaces Corrosion Resistant and Terminal • • • Leads are Readily Solderable Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds Shipped 50 units per plastic tube Marking: U1610, U1615, U1620, U1640, U1660 4 MARKING DIAGRAM U16xx 1 2 3 TO–220AB CASE 221A PLASTIC MAXIMUM RATINGS Please See the Table on the Following Page U16xx = Device Code xx = 10, 15, 20, 40 or 60 ORDERING INFORMATION Device Semiconductor Components Industries, LLC, 2000 October, 2000 – Rev. 3 1 Package Shipping MUR1610CT TO–220 50 Units/Rail MUR1615CT TO–220 50 Units/Rail MUR1620CT TO–220 50 Units/Rail MUR1640CT TO–220 50 Units/Rail MUR1660CT TO–220 50 Units/Rail Publication Order Number: MUR1620CT/D MUR1610CT, MUR1615CT, MUR1620CT, MUR1640CT, MUR1660CT MAXIMUM RATINGS MUR16 Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current Total Device, (Rated VR), TC = 150°C Per Leg Total Device Symbol 10CT 15CT 20CT 40CT 60CT Unit VRRM VRWM VR 100 150 200 400 600 Volts IF(AV) 8.0 16 Amps Peak Rectified Forward Current Per Diode Leg (Rated VR, Square Wave, 20 kHz), TC = 150°C IFM 16 Amps Nonrepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) IFSM 100 Amps Operating Junction Temperature and Storage Temperature TJ, Tstg 65 to +175 °C THERMAL CHARACTERISTICS (Per Diode Leg) Maximum Thermal Resistance, Junction to Case RθJC 3.0 °C/W 2.0 ELECTRICAL CHARACTERISTICS (Per Diode Leg) Maximum Instantaneous Forward Voltage (Note 1.) (iF = 8.0 Amps, TC = 150°C) (iF = 8.0 Amps, TC = 25°C) vF Maximum Instantaneous Reverse Current (Note 1.) (Rated dc Voltage, TC = 150°C) (Rated dc Voltage, TC = 25°C) iR Maximum Reverse Recovery Time (IF = 1.0 Amp, di/dt = 50 Amps/µs) (IF = 0.5 Amp, IR = 1.0 Amp, IREC = 0.25 Amp) trr Volts 0.895 0.975 1. Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤ 2.0% http://onsemi.com 2 1.00 1.30 1.20 1.50 µA 250 5.0 500 10 35 25 60 50 ns MUR1610CT, MUR1615CT, MUR1620CT, MUR1640CT, MUR1660CT MUR1610CT, MUR1615CT, MUR1620CT 100 IR, REVERSE CURRENT ( A) 70 50 30 TJ = 175°C 100°C 10 7.0 TJ = 175°C 100°C 0.8 0.4 0.2 0.08 0.04 0.02 25°C 0 25°C 20 40 60 5.0 80 100 120 140 160 180 200 VR, REVERSE VOLTAGE (VOLTS) Figure 2. Typical Reverse Current, Per Leg* 3.0 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. 2.0 IF(AV) , AVERAGE POWER DISSIPATION (WATTS) i F , INSTANTANEOUS FORWARD CURRENT (AMPS) 20 800 400 200 80 40 20 8.0 4.0 2.0 1.0 0.7 0.5 0.3 0.2 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 1.0 0.9 1.1 1.2 10 RATED VR APPLIED 9.0 8.0 7.0 6.0 5.0 dc 4.0 3.0 2.0 1.0 0 vF, INSTANTANEOUS VOLTAGE (VOLTS) SQUARE WAVE 140 150 145 155 160 165 170 175 180 TC, CASE TEMPERATURE (°C) Figure 1. Typical Forward Voltage, Per Leg 14 12 PF(AV) , AVERAGE POWER DISSIPATION (WATTS) IF(AV) , AVERAGE FORWARD CURRENT (AMPS) Figure 3. Current Derating, Case, Per Leg RJA = 16°C/W RJA = 60°C/W (NO HEATSINK) dc 10 8.0 SQUARE WAVE 6.0 4.0 dc 2.0 SQUARE WAVE 0 0 20 40 60 80 100 120 140 160 180 200 10 TJ = 175°C 9.0 8.0 SQUARE WAVE 7.0 dc 6.0 5.0 4.0 3.0 2.0 1.0 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 TA, AMBIENT TEMPERATURE (°C) IF(AV), AVERAGE FORWARD CURRENT (AMPS) Figure 4. Current Derating, Ambient, Per Leg Figure 5. Power Dissipation, Per Leg http://onsemi.com 3 10 MUR1610CT, MUR1615CT, MUR1620CT, MUR1640CT, MUR1660CT MUR1640CT 70 50 100°C TJ = 175°C 20 25°C 10 7.0 800 400 200 TJ = 175°C 80 40 20 8.0 4.0 2.0 150°C 100°C 0.8 0.4 0.2 0.08 0.04 0.02 25°C 0 50 100 5.0 150 200 250 300 350 450 500 400 VR, REVERSE VOLTAGE (VOLTS) Figure 7. Typical Reverse Current, Per Leg* 3.0 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these curves if VR is sufficiently below rated VR. 2.0 IF(AV) , AVERAGE POWER DISSIPATION (WATTS) i F , INSTANTANEOUS FORWARD CURRENT (AMPS) 30 IR, REVERSE CURRENT ( A) 100 1.0 0.7 0.5 0.3 0.2 0.1 0.4 0.6 0.8 1.0 1.2 1.4 1.6 10 RATED VR APPLIED 9.0 8.0 7.0 6.0 5.0 dc 4.0 3.0 2.0 1.0 0 vF, INSTANTANEOUS VOLTAGE (VOLTS) SQUARE WAVE 140 150 145 155 160 165 170 175 180 TC, CASE TEMPERATURE (°C) Figure 6. Typical Forward Voltage, Per Leg 14 PF(AV) , AVERAGE POWER DISSIPATION (WATTS) IF(AV) , AVERAGE FORWARD CURRENT (AMPS) Figure 8. Current Derating, Case, Per Leg RJA = 16°C/W RJA = 60°C/W (NO HEAT SINK) 12 10 dc 8.0 6.0 SQUARE WAVE 4.0 dc 2.0 SQUARE WAVE 0 0 20 40 60 80 100 120 140 160 180 200 10 TJ = 175°C 9.0 SQUARE WAVE dc 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 TA, AMBIENT TEMPERATURE (°C) IF(AV), AVERAGE FORWARD CURRENT (AMPS) Figure 9. Current Derating, Ambient, Per Leg Figure 10. Power Dissipation, Per Leg http://onsemi.com 4 10 MUR1610CT, MUR1615CT, MUR1620CT, MUR1640CT, MUR1660CT MUR1660CT 100 IR, REVERSE CURRENT ( A) 70 50 TJ = 150°C 20 100°C 10 25°C 7.0 TJ = 150°C 100°C 25°C 100 200 5.0 300 400 600 500 VR, REVERSE VOLTAGE (VOLTS) Figure 12. Typical Reverse Current, Per Leg* 3.0 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. 2.0 IF(AV) , AVERAGE POWER DISSIPATION (WATTS) i F , INSTANTANEOUS FORWARD CURRENT (AMPS) 30 800 400 200 80 40 20 8.0 4.0 2.0 0.8 0.4 0.2 0.08 0.04 0.02 1.0 0.7 0.5 0.3 0.2 0.1 0.4 0.6 0.8 1.0 1.2 1.6 1.4 1.8 10 RATED VR APPLIED 9.0 8.0 7.0 6.0 5.0 dc 4.0 3.0 2.0 1.0 0 vF, INSTANTANEOUS VOLTAGE (VOLTS) SQUARE WAVE 140 150 145 155 160 165 170 175 180 TC, CASE TEMPERATURE (°C) Figure 11. Typical Forward Voltage, Per Leg 10 RJA = 16°C/W RJA = 60°C/W (NO HEAT SINK) 9.0 dc 8.0 PF(AV) , AVERAGE POWER DISSIPATION (WATTS) IF(AV) , AVERAGE FORWARD CURRENT (AMPS) Figure 13. Current Derating, Case, Per Leg 7.0 6.0 SQUARE WAVE 5.0 4.0 dc 3.0 2.0 SQUARE WAVE 1.0 0 0 20 40 60 80 100 120 140 160 180 200 14 13 12 11 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 SQUARE WAVE TJ = 175°C dc 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 TA, AMBIENT TEMPERATURE (°C) IF(AV), AVERAGE FORWARD CURRENT (AMPS) Figure 14. Current Derating, Ambient, Per Leg Figure 15. Power Dissipation, Per Leg http://onsemi.com 5 10 1.0 D = 0.5 0.5 0.2 0.1 0.1 0.05 0.05 t1 0.01 0.02 0.01 ZθJC(t) = r(t) RθJC P(pk) 0.01 0.02 0.05 D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT T1 t2 TJ(pk) - TC = P(pk) ZθJC(t) DUTY CYCLE, D = t1/t2 SINGLE PULSE 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 t, TIME (ms) Figure 16. Thermal Response 1000 C, CAPACITANCE (pF) r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) MUR1610CT, MUR1615CT, MUR1620CT, MUR1640CT, MUR1660CT MUR1620CT THRU 1660CT MUR1605CT THRU 1615CT 300 TJ = 25°C 100 30 10 1.0 10 VR, REVERSE VOLTAGE (VOLTS) Figure 17. Typical Capacitance, Per Leg http://onsemi.com 6 100 100 200 500 1000 MUR1610CT, MUR1615CT, MUR1620CT, MUR1640CT, MUR1660CT PACKAGE DIMENSIONS TO–220 THREE–LEAD TO–220AB CASE 221A–09 ISSUE AA –T– B SEATING PLANE C F T S 4 DIM A B C D F G H J K L N Q R S T U V Z A Q 1 2 3 U H K Z L R V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. J G D N http://onsemi.com 7 INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 ----0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 ----2.04 MUR1610CT, MUR1615CT, MUR1620CT, MUR1640CT, MUR1660CT SWITCHMODE is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada N. American Technical Support: 800–282–9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor – European Support German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET) Email: ONlit–[email protected] French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET) Email: ONlit–[email protected] English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT) Email: [email protected] CENTRAL/SOUTH AMERICA: Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST) Email: ONlit–[email protected] Toll–Free from Mexico: Dial 01–800–288–2872 for Access – then Dial 866–297–9322 ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001–800–4422–3781 Email: ONlit–[email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781 *Available from Germany, France, Italy, UK, Ireland For additional information, please contact your local Sales Representative. http://onsemi.com 8 MUR1620CT/D