BYW80−200 SWITCHMODE Power Rectifiers . . . designed for use in switching power supplies, inverters and as free wheeling diodes, these state-of-the-art devices have the following features: • • • • • • • http://onsemi.com Ultrafast 35 Nanosecond Recovery Time 175°C Operating Junction Temperature Popular TO-220 Package Epoxy Meets UL94, VO @ 1/8″ Low Forward Voltage Low Leakage Current High Temperature Glass Passivated Junction ULTRAFAST RECTIFIERS 8.0 AMPERES 200 V Mechanical Characteristics: 1 • Case: Epoxy, Molded • Weight: 1.9 grams (approximately) • Finish: All External Surfaces Corrosion Resistant and Terminal 4 3 Leads are Readily Solderable • Lead Temperature for Soldering Purposes: • • 260°C Max. for 10 Seconds Shipped 50 units per plastic tube Marking: , BYW80-200 MARKING DIAGRAM 4 MAXIMUM RATINGS Please See the Table on the Following Page BYW80- 20 0 1 3 CASE 221B TO - 220AC PLASTIC BYW80- 200 = Device Code ORDERING INFORMATION Semiconductor Components Industries, LLC, 2003 July, 2003 - Rev. 1 1 Device Package Shipping BYW80- 200 TO - 220 50 Units/Rail Publication Order Number: BYW80/D BYW80 - 200 MAXIMUM RATINGS Symbol Values Unit Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Rating VRRM VRWM VR 200 Volts Average Rectified Forward Current Total Device, (Rated VR), TC = 150°C IF(AV) 8.0 Amps Peak Repetitive Forward Current (Rated VR, Square Wave, 20 kHz), TC = 150°C IFM 16 Amps Nonrepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) IFSM 100 Amps TJ, Tstg - 65 to +175 °C RθJC 3.0 °C/W Operating Junction Temperature and Storage Temperature Range THERMAL CHARACTERISTICS Maximum Thermal Resistance, Junction to Case ELECTRICAL CHARACTERISTICS Maximum Instantaneous Forward Voltage (Note 1.) (iF = 7.0 Amps, TC = 100°C) (iF = 22 Amps, TC = 25°C) vF Maximum Instantaneous Reverse Current (Note 1.) (Rated dc Voltage, TJ = 100°C) (Rated dc Voltage, TJ = 25°C) iR Maximum Reverse Recovery Time (IF = 1.0 Amp, di/dt = 50 Amps/µs) (IF = 0.5 Amp, iR = 1.0 Amp, IREC = 0.25 Amp) trr Volts 0.85 1.25 mA 1 0.01 ns 35 25 1. Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤ 2.0%. http://onsemi.com 2 BYW80 - 200 1000 100 IR, REVERSE CURRENT ( A) 70 50 20 10 100°C 1.0 25°C 0.1 10 0.01 7.0 0 20 40 60 120 140 180 200 160 Figure 2. Typical Reverse Current* * The curves shown are typical for the highest voltage device in the grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if VR is sufficiently below rated VR. 3.0 2.0 TJ = 175°C 100°C 25°C 1.0 0.7 0.5 0.3 0.2 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 10 9.0 RATED VR APPLIED 8.0 dc 7.0 6.0 SQUARE WAVE 5.0 4.0 3.0 2.0 1.0 0 140 150 vF, INSTANTANEOUS VOLTAGE (VOLTS) PF(AV) , AVERAGE POWER DISSIPATION (WATTS) RJA = 16°C/W RJA = 60°C/W (NO HEAT SINK) dc 10 SQUARE WAVE 8.0 6.0 4.0 dc 2.0 SQUARE WAVE 0 0 20 40 60 80 100 120 140 180 170 Figure 3. Current Derating, Case 14 12 160 TC, CASE TEMPERATURE (°C) Figure 1. Typical Forward Voltage IF(AV) , AVERAGE FORWARD CURRENT (AMPS) 100 80 VR, REVERSE VOLTAGE (VOLTS) 5.0 IF(AV) , AVERAGE FORWARD CURRENT (AMPS) i F , INSTANTANEOUS FORWARD CURRENT (AMPS) 30 TJ = 175°C 100 160 180 200 10 9.0 TJ = 175°C 8.0 7.0 SQUARE WAVE 6.0 dc 5.0 4.0 3.0 2.0 1.0 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 TA, AMBIENT TEMPERATURE (°C) IF(AV), AVERAGE FORWARD CURRENT (AMPS) Figure 4. Current Derating, Ambient Figure 5. Power Dissipation http://onsemi.com 3 9.0 10 1.0 D = 0.5 0.5 0.2 0.1 0.1 0.05 0.01 ZJC(t) = r(t) RJC RJC = 1.5 C/W MAX P(pk) 0.05 t2 SINGLE PULSE 0.02 0.01 0.01 D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT T1 t1 DUTY CYCLE, D = t1/t2 0.02 0.05 0.1 0.2 0.5 1.0 2.0 5.0 10 20 TJ(pk) − TC = P(pk) ZθJC(t) 50 t, TIME (ms) Figure 6. Thermal Response 1000 C, CAPACITANCE (pF) r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) BYW80 - 200 300 TJ = 25°C 100 30 10 1.0 10 VR, REVERSE VOLTAGE (VOLTS) Figure 7. Typical Capacitance http://onsemi.com 4 100 100 200 500 1000 BYW80 - 200 PACKAGE DIMENSIONS TO - 220 TWO - LEAD CASE 221B - 04 ISSUE D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. C B Q F S T DIM A B C D F G H J K L Q R S T U 4 A 1 U 3 H K L R D G J http://onsemi.com 5 INCHES MIN MAX 0.595 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.190 0.210 0.110 0.130 0.018 0.025 0.500 0.562 0.045 0.060 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 MILLIMETERS MIN MAX 15.11 15.75 9.65 10.29 4.06 4.82 0.64 0.89 3.61 3.73 4.83 5.33 2.79 3.30 0.46 0.64 12.70 14.27 1.14 1.52 2.54 3.04 2.04 2.79 1.14 1.39 5.97 6.48 0.000 1.27 BYW80 - 200 SENSEFET is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303 - 675- 2175 or 800 - 344- 3860 Toll Free USA/Canada Fax: 303 - 675- 2176 or 800 - 344- 3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 2- 9- 1 Kamimeguro, Meguro - ku, Tokyo, Japan 153 - 0051 Phone: 81 - 3- 5773- 3850 ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800 - 282- 9855 Toll Free USA/Canada http://onsemi.com 6 BYW80/D